summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
Commit message (Collapse)AuthorAgeLines
* MLK-11528 imx: mx6ul check fuse before init beePeng Fan2017-03-14-1/+11
| | | | | | | | | | | | Need to check fuse bit 25 of bank 0 word 4 before initialize bee. The bit: 0 means bee enabled, 1 means bee disabled. If disabled, continuing initialize bee will cause system hang, so need to check this bit before initialize bee. Add macro to enable BEE in header file, default disabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit ef4cb7c53418e4e1dd7cfcb7c6974cfea77ef3c0)
* MLK-10958 imx: mx6ul support Bus Encryption EnginePeng Fan2017-03-14-1/+463
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is to support Bus Encryption Engine(BEE) for i.MX 6UL. Supported feature: 1. SNVS key and soft key 2. CTR and ECB mode 3. Specify address region to bee. Two commands are included: bee init [key] [mode] [start] [end] - BEE block initial "Example: bee init 1 1 0x80000000 0x80010000\n" bee test [region] "Example: bee test 1\n" Mapping: [0x10000000 - (0x10000000 + size - 1)] : [start - (start + size - 1)] [0x30000000 - (0x30000000 + IRAM_SIZE - 1)] : [IRAM_BASE_ADDR - (IRAM_BASE_ADDR + IRAM_SIZE - 1)] Whatever start is, start - (start + size -1) will be fixed mapping to 0x10000000 - (0x10000000 + size - 1) Since default AES region's protected size is SZ_512M, so on mx6ul evk board, you can not simply run 'bee init', it will overlap with uboot execution environment, you can use 'bee init 0 0 0x80000000 0x81000000'. If want to use bee, Need to define CONFIG_CMD_BEE in board configuration header file, since CONFIG_CMD_BEE default is not enabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 29b9bdbbdac9678dba9b7bc2d3662598e9c548a5) (cherry picked from commit 6d45292ff7e7020a48842f033f8a337daabe4476)
* MLK-14422 imx7d: wdog: Overwrite the reset_cpu to turn off internal reset signalYe Li2017-03-14-0/+15
| | | | | | | | Set wdog WCR register SRS bit to turn off internal reset signal WDOG_RESET_B_DEB for mx7d. So that the warm reset is disabled. The WDA is cleared to output WDOG_B immediately to reset the board. Signed-off-by: Ye Li <ye.li@nxp.com>
* ARM: Migrate errata to KconfigTom Rini2017-03-09-0/+8
| | | | | | | | | This moves all of the current ARM errata from various header files and in to Kconfig. This allows for a minor amount of cleanup as we had some instances where both a general common header file was enabling errata as well as the board config. We now just select these once at the higher level in Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada2017-02-12-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini2017-02-03-24/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/ls1046aqds_defconfig configs/ls1046aqds_nand_defconfig configs/ls1046aqds_qspi_defconfig configs/ls1046aqds_sdcard_ifc_defconfig configs/ls1046aqds_sdcard_qspi_defconfig configs/ls1046ardb_emmc_defconfig configs/ls1046ardb_qspi_defconfig configs/ls1046ardb_sdcard_defconfig
| * arch: arm: update the IFC IP input clockPrabhakar Kushwaha2017-02-03-24/+5
| | | | | | | | | | | | | | | | | | | | | | | | IFC IP clock is always a constant divisor of platform clock pre-defined per SoC. Clock control register (CCR) used in current implementation governs IFC IP output clock. Update sys_info->freq_localbus to represent IFC input clock with value constant divisor of platform clock. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls1046a: Enable workaround for erratum A-008336York Sun2017-01-31-0/+1
| | | | | | | | | | | | | | Erratum A-008336 applies to LS1046A per latest SoC document. Signed-off-by: York Sun <york.sun@nxp.com> CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2017-02-01-1/+214
|\ \
| * | BOARD: MCCMON6: Provide support for iMX6q based mccmon6 boardLukasz Majewski2017-01-30-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | This patch provides u-boot support for Liebherr (LWN) mccmon6 board. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
| * | ARM: imx6ul: Move liteSOM source to SoC directoryMarcin Niestroj2017-01-27-1/+209
| |/ | | | | | | | | | | | | | | | | | | | | Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested in [1] during discussion of chiliSOM support patches. [1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm64: spin-table: add more information in Kconfig helpMasahiro Yamada2017-01-28-2/+4
|/ | | | | | | | | | | | | | | | | | | | | This feature seems to be sometimes misunderstood. The intention is: [1] Bring the slaves into the U-Boot proper image, not SPL (unless you have a special reason to do otherwise). [2] The operation must be done in a board (SoC) specific manner since how to wake the slaves from the Boot ROM is SoC specific. [3] The slaves must enter U-Boot proper after U-Boot relocates itself because the "cpu-release-addr" property points to the relocated memory area. [2] is already explained in the help. We can make [1] even clearer by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing, so I am adding it to the list. Instead, "before the master CPU jumps to the kernel" is a matter of course, so removed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass2017-01-25-0/+8
| | | | | | | This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_ARCH_EARLY_INIT_R to KconfigSimon Glass2017-01-25-0/+4
| | | | | | | This converts the following to Kconfig: CONFIG_ARCH_EARLY_INIT_R Signed-off-by: Simon Glass <sjg@chromium.org>
* Kconfig: Migrate BOARD_LATE_INIT to a selectTom Rini2017-01-24-0/+34
| | | | | | | | | This option should not really be user selectable. Note that on PowerPC we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be conditional on that. Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
* status_led: Kconfig migrationUri Mashiach2017-01-21-17/+18
| | | | | | | | | | | | | Move all of the status LED feature to drivers/led/Kconfig. The LED status definitions were moved from the board configuration files to the defconfig files. TBD: Move all of the definitions in the include/status_led.h to the relevant board's defconfig files. Tested boards: CL-SOM-AM57x, CM-T335 Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
* serial, ns16550: bugfix: ns16550 fifo not enabledHeiko Schocher2017-01-20-4/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit: 65f83802b7a5b "serial: 16550: Add getfcr accessor" breaks u-boot commandline working with long commands sending to the board. Since the above patch, you have to setup the fcr register. For board/archs which enable OF_PLATDATA, the new field fcr in struct ns16550_platdata is not filled with a default value ... This leads in not setting up the uarts fifo, which ends in problems, when you send long commands to u-boots commandline. Detected this issue with automated tbot tests on am335x based shc board. The error does not popup, if you type commands. You need to copy&paste a long command to u-boots commandshell (or send a long command with tbot) Possible boards/plattforms with problems: ./arch/arm/cpu/arm926ejs/lpc32xx/devices.c ./arch/arm/mach-tegra/board.c ./board/overo/overo.c ./board/quipos/cairo/cairo.c ./board/logicpd/omap3som/omap3logic.c ./board/logicpd/zoom1/zoom1.c ./board/timll/devkit8000/devkit8000.c ./board/lg/sniper/sniper.c ./board/ti/beagle/beagle.c ./drivers/serial/serial_rockchip.c Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini2017-01-19-79/+1012
|\
| * kconfig: fsl PPA: move CONFIG_* to KconfigHou Zhiqiang2017-01-18-2/+26
| | | | | | | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * ARMv8/sec_firmware: relocated and renamed the config FSL_PPA_ARMV8_PSCIHou Zhiqiang2017-01-18-14/+14
| | | | | | | | | | | | | | | | Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * kconfig: armv8: move armv8 sec_firmware CONFIG_* to KconfigHou Zhiqiang2017-01-18-3/+36
| | | | | | | | | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [York S: clean up scripts/config_whitelist.txt] Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: aarch64: Fix the warning about x1-x3 nonzero issueAlison Wang2017-01-18-32/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | For 64-bit kernel, there is a warning about x1-x3 nonzero in violation of boot protocol. To fix this issue, input argument 4 is added for armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will be set to the right value, such as zero. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Alexander Graf <agraf@suse.de> Tested-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/fsl-layerscape: fdt: fixup LS1043A rev1 MSI nodeWenbin Song2017-01-18-0/+157
| | | | | | | | | | | | | | | | | | | | The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if rev1.1 silicon used, need to fixup the MSI node to match it. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043a: fixup GIC offset for ls1043a rev1Wenbin Song2017-01-18-5/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The LS1043A rev1.1 silicon supports two types of GIC offset: 4K alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT] is used to choose which offset will be used. The LS1043A rev1.0 silicon only supports the CIG offset with 4K alignment. If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment is used. 64K alignment is the default setting. Overriding the weak smp_kick_all_cpus, the new impletment is able to detect GIC offset. The default GIC offset in kernel device tree is using 4K alignment, it need to be fixed if 64K alignment is detected. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-lsch3: enable snoopable sata read and writeTang Yuantian2017-01-18-0/+2
| | | | | | | | | | | | | | | | | | By default the SATA IP on the ls208Xa SoCs does not generating coherent/snoopable transactions. This patch enable it in the sata axicc register. Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/fsl_lsch2: Add chip power supply voltage setupHou Zhiqiang2017-01-18-0/+361
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set up chip power supply voltage according to voltage ID. The fuse status register provides the values from on-chip voltage ID fuses programmed at the factory. These values define the voltage requirements for the chip. Main operations: 1. Set up the core voltage 2. Set up the SERDES voltage and reset SERDES lanes 3. Enable/disable DDR controller support 0.9V if needed Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-layerscape: Fix SECURE_BOOT configYork Sun2017-01-18-1/+1
| | | | | | | | | | | | | | | | | | | | | | Without a prompt in Kconfig, SECURE_BOOT cannot be selected by defconfig. The option was dropped unintentionally when defconfig files were cleaned up. Three targets were impacted ls1043ardb_SECURE_BOOT, ls2080ardb_SECURE_BOOT, ls2080aqds_SECURE_BOOT. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * armv8/fsl-lsch3: consolidate the clock system initializationHou Zhiqiang2017-01-18-7/+21
| | | | | | | | | | | | | | | | This patch binds the sys_info->freq_systembus to Platform PLL, and implements the IPs' clock function individually. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/fsl-lsch2: refactor the clock system initializationHou Zhiqiang2017-01-18-18/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Up to now, there are 3 kind of SoCs under Layerscape Chassis 2, like LS1043A, LS1046A and LS1012A. But the clocks tree has a lot of differences, for instance, the IP modules have different dividers to derive its clock from Platform PLL. And the core cluster PLL and platform PLL maybe have different reference clocks, such as LS1012A. Another problem is which clock/PLL should be described by sys_info->freq_systembus, it is confused in Layerscape Chissis 2. This patch is to bind the sys_info->freq_systembus to the Platform PLL, and handle the different divider of IP modules separately between different SoCs, and separate reference clocks of core cluster PLL and platform PLL. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * ARMv8/fsl-layerscape: Enable data coherency between cores in clusterHou Zhiqiang2017-01-18-0/+4
| | | | | | | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: Enable CPUECTLR.SMPEN for coherencyMingkai Hu2017-01-18-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is set. The SMPEN bit should be set before enabling the data cache. If not enabled, the cache is not coherent with other cores and data corruption could occur. For A57/A72, SMPEN bit enables the processor to receive instruction cache and TLB maintenance operations broadcast from other processors in the cluster. This bit should be set before enabling the caches and MMU, or performing any cache and TLB maintenance operations. Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/fsl_lsch2: Add the OCRAM initializationHou Zhiqiang2017-01-18-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Clear the content to zero and the ECC error bit of OCRAM1/2. The OCRAM must be initialized to ZERO by the unit of 8-Byte before accessing it, or else it will generate ECC error. And the IBR has accessed the OCRAM before this initialization, so the ECC error status bit should to be cleared. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * kconfig: move FSL_PCIE_COMPAT to platform KconfigHou Zhiqiang2017-01-18-0/+19
| | | | | | | | | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-layerscape, ccn504: Set forced-order mode in RNI-6, RNI-20Priyanka Jain2017-01-18-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | It is recommended to set forced-order mode in RNI-6, RNI-20 for performance optimization in LS2088A. Both LS2080A, LS2088A families has CONFIG_LS2080A define. As above update is required only for LS2088A, skip this for LS2080A SoC family. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | armv8: fix #if around spin-table code in start.SOded Gabbay2017-01-14-1/+1
| | | | | | | | | | | | | | | | | | | | Using CONFIG_IS_ENABLED() doesn't work in SPL. This patch replaces the only occurrence of CONFIG_IS_ENABLED() in start.S to a regular #if defined(). It also adds "&& !defined(CONFIG_SPL_BUILD)" to that #if statement because the spin-table code can't currently work in SPL, and the spin-table file isn't even compiled in SPL. Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
* | Merge tag 'xilinx-for-v2017.03' of git://www.denx.de/git/u-boot-microblazeTom Rini2017-01-11-1/+91
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | Xilinx changes for v2017.03 - ATF handoff - DT syncups - gem: Use wait_for_bit(), add simple clk support - Simple clk driver for ZynqMP - Other small changes
| * | ARM64: zynqmp: Generate handoff structure for ATFMichal Simek2017-01-10-1/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xilinx ATF extending options for passing images from BL2(FSBL) to BL31. U-Boot SPL is FSBL replacement that's why it should generate handoff structure the same. Support only one entry which is U-Boot in EL2 itself. When FIT image is adopted structure generate should be data driven. Currently ATF is placing this structure at the beggining of OCM which is rewriting early parts of ATF which should be unused at that time. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | ARM: zynqmp: Make SYS_VENDOR configurableMike Looijmans2017-01-10-0/+1
| |/ | | | | | | | | | | | | Add a string description for SYS_VENDOR to allow configuring boards from other vendors than just "xilinx". Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | mmc: move more driver config options to KconfigMasahiro Yamada2017-01-11-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move (and rename) the following CONFIG options to Kconfig: CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI) CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS) CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC) CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS) CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA) CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI) They are the same option names as used in Linux. This commit was created as follows: [1] Rename the options with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g ' [2] Commit the changes [3] Create entries in driver/mmc/Kconfig. (copied from Linux) [4] Move the options with the following command tools/moveconfig.py -y -r HEAD \ MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI [5] Sort and align drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini2017-01-10-3/+61
|\ \ | |/ |/|
| * ARM: boot0 hook: remove macro, include whole header fileAndre Przywara2017-01-04-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For prepending some board specific header area to U-Boot images we were so far including a header file with a macro definition containing the actual header specification. This works fine if there are just a few statements and if there is only one alternative. However adding more complex code quickly gets messy with this approach, so let's just drop that intermediate macro and let the #include actually insert the code directly. This converts the callers and the callees, but doesn't change anything at this point. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Steve Rae <steve.rae@raedomain.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
| * armv8: move reset branch into boot hookAndre Przywara2017-01-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | The boot0 hook we have so far is applied _after_ the initial branch to the "reset" entry point. An upcoming change requires even this branch to be changed, so we apply the hook macro at the earliest point, and have the branch in the hook file as well. This is no functional change at this point, just refactoring to simplify upcoming patches. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
| * armv8: add simple sdelay implementationAndre Przywara2017-01-04-0/+14
| | | | | | | | | | | | | | | | | | The sunxi DRAM setup code needs an sdelay() implementation, which wasn't defined for armv8 so far. Shamelessly copy the armv7 version and adjust it to work in AArch64. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
| * armv8: add lowlevel_init.SAndre Przywara2017-01-04-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | For boards that call s_init() when the SPL runs, we are expected to setup an early stack before calling this C function. Implement the proper AArch64 version of this based on the ARMv7 code. This allows sunxi boards to setup the basic peripherals even with a 64-bit SPL. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
* | ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to KconfigYork Sun2017-01-04-9/+0
| | | | | | | | | | | | | | | | Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing usage in ls102xa and fsl-layerscape. Remove all powerpc macros in config header and board header files. Signed-off-by: York Sun <york.sun@nxp.com>
* | arm: layerscape: Move CONFIG_SYS_FSL_ERRATUM_* to KconfigYork Sun2017-01-04-0/+48
| | | | | | | | | | | | Use Kconfig to select errata workaround. Signed-off-by: York Sun <york.sun@nxp.com>
* | fsl_ddr: Move DDR config options to driver KconfigYork Sun2017-01-04-93/+11
| | | | | | | | | | | | | | | | | | Create driver/ddr/fsl/Kconfig and move existing options. Clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com> [trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: Tom Rini <trini@konsulko.com>
* | crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to KconfigYork Sun2017-01-04-0/+3
| | | | | | | | | | | | | | Use Kconfig option to set little- or big-endian access to secure boot and trust architecture. Signed-off-by: York Sun <york.sun@nxp.com>
* | crypto: Move SYS_FSL_SEC_COMPAT into driver KconfigYork Sun2017-01-04-0/+6
|/ | | | | | | Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC and ARM SoCs, move it to Kconfig under the driver. Signed-off-by: York Sun <york.sun@nxp.com>
* ARM64: zynqmp: Add missing SPL dependency for boot.bin generationMichal Simek2016-12-20-0/+1
| | | | | | | boot.bin file is generated only when SPL is selected. Reflect this depency in Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit v1.1 at 2024-10-07 18:23:20 +0000