summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7
Commit message (Collapse)AuthorAgeLines
* kconfig: add CONFIG_SUPPORT_SPLMasahiro Yamada2014-10-27-0/+23
| | | | | | | | | CONFIG_SPL should not be enabled for boards that do not have SPL. CONFIG_SUPPORT_SPL introduced by this commit should be "select"ed by boards with SPL support and CONFIG_SPL should depend on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* Rename some defines containing FAT in their name to be filesystem genericGuillaume GARDET2014-10-27-4/+4
| | | | | | | | | | | Rename some defines containing FAT in their name to be filesystem generic: MMCSD_MODE_FAT => MMCSD_MODE_FS CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-imxTom Rini2014-10-27-0/+1
|\
| * ARM: i.MX6: include prototype for get_board_rev()Eric Nelson2014-10-21-0/+1
| | | | | | | | | | | | | | Include <asm/bootm.h> to see the prototype for get_board_rev() and prevent warning "Should it be static?" with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2014-10-27-460/+739
|\ \
| * | omap3: Kconfig: fix the cm-t35 board option promptIgor Grinberg2014-10-23-1/+1
| | | | | | | | | | | | | | | | | | | | | The cm-t35 board support covers both cm-t3530 and cm-t3730 boards. Mention both boards in the Kconfig option prompt. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
| * | ARM: keystone: cmd_ddr3: add ddr3 commands to test ddrHao Zhang2014-10-23-1/+249
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ddr3 commands: test <start_addr in hex> <end_addr in hex> - test DDR from start\n address to end address\n ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n compare DDR data of (size) bytes from start address to end address\n ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n in DDR data at <addr>, the command will read a 32-bit data\n from <addr>, and write (data ^ bit_err) back to <addr>\n Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used for ddr3 commands and for now it's not needed any more. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: ecc: add ddr3 error detection and correction supportVitaly Andrianov2014-10-23-0/+244
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the DDR3 ECC support to enable ECC in the DDR3 EMIF controller for Keystone II devices. By default, ECC will only be enabled if RMW is supported in the DDR EMIF controller. The entire DDR memory will be scrubbed to zero using an EDMA channel after ECC is enabled and before u-boot is re-located to DDR memory. An ecc_test environment variable is added for ECC testing. If ecc_test is set to 0, a detection of 2-bit error will reset the device, if ecc_test is set to 1, 2-bit error detection will not reset the device, user can still boot the kernel to check the ECC error handling in kernel. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | ARM: keystone: msmc: extend functionality of SESVitaly Andrianov2014-10-23-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add functions to set/get SES PMAX values of Pivilege ID pair. Also add msmc module definitions. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | ARM: keystone: clock: add support for K2E SoCsKhoronzhuk, Ivan2014-10-23-4/+13
| | | | | | | | | | | | | | | | | | | | | | | | For K2E and K2L SoCs clock output from PASS PLL has to be enabled after NETCP domain and PA module are enabled. So create new function for that and call it after PA module is enabled. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: k2l-evm: add board supportHao Zhang2014-10-23-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds Keystone II Lammar (K2L) EVM board support. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: enable OSR clock domain for K2L SoCHao Zhang2014-10-23-0/+51
| | | | | | | | | | | | | | | | | | | | | This patches enables the On-chip Shared Ram clock domain for K2L SoC. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | ARM: keystone2: spl: move board specific codeHao Zhang2014-10-23-54/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | The initialization of PLLs is a part of board specific code, so move it appropriate places. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: msmc: add MSMC cache coherency support for K2L SOCHao Zhang2014-10-23-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds Keystone II Lamar (K2L) SoC specific definitions to support MSMC cache coherency. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: clock: add K2L clock definitions and commandsHao Zhang2014-10-23-0/+139
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds clock definitions and commands to support Keystone II K2L SOC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | ARM: cmd_clock: generalize command usage descriptionKhoronzhuk, Ivan2014-10-23-17/+7
| | | | | | | | | | | | | | | | | | | | | | | | The usage description of commands refers to headers of sources, that is not correct. This patch is intended to fix it. Also generalize code in order to reduce SoC dependent #ifdefs. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | dma: keystone_nav: move keystone_nav driver to driver/dma/Khoronzhuk, Ivan2014-10-23-355/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The keystone_nav is used by drivers/net/keystone_net.c driver to send and receive packets, but currently it's placed at keystone arch sources. So it should be in the drivers directory also. It's separate driver that can be used for sending and receiving pktdma packets by others drivers also. This patch just move this driver to appropriate directory and doesn't add any functional changes. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: keystone_nav: don't use hard addresses in netcp_pktdmaKhoronzhuk, Ivan2014-10-23-25/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | Use definitions in netcp_pktdma instead direct addresses. The definitions can be set specifically for SoC, so there is no reason to check SoC type while initialization. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | keystone2: keystone_nav: don't use hard addresses in qm_configKhoronzhuk, Ivan2014-10-23-30/+19
| | | | | | | | | | | | | | | | | | | | | | | | Use definitions in qm_config. The definitions can be set specifically for SoC, so there is no reason to check SoC type while initialization. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini2014-10-27-10/+1
|\ \ \
| * | | arm: socfpga: Zap spl.h and ad-hoc related symsMarek Vasut2014-10-27-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch to the common spl.h file and zap the arch/spl.h . Since the arch/spl.h contained various ad-hoc symbols, zap those symbols as well and rework the board configuration a little so it doesn't depend on them. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Vince Bridgers <vbridger@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Pavel Machek <pavel@denx.de>
| * | | arm: socfpga: Move code from misc_init_r() to arch_early_init_r()Marek Vasut2014-10-27-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move this initialization code to proper place. The misc_init_r() function is called way too late and the platform initialization code should be executed much earlier. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Vince Bridgers <vbridger@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Pavel Machek <pavel@denx.de>
* | | | Merge http://git.denx.de/u-boot-sunxiTom Rini2014-10-26-23/+181
|\ \ \ \
| * | | | sunxi: Add CONFIG_OLD_SUNXI_KERNEL_COMPAT Kconfig optionHans de Goede2014-10-24-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a Kconfig option which users can select when they want to boot older kernels, e.g. the linux-sunxi 3.4 kernels. For now this just forces the pll5 "p" value to 1 (divide by 2) as that is what those kernels are hardcoded too, in the future this may enable further workarounds. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Tom Rini <trini@ti.com> -- Changes in v2: -s/CONFIG_OLD_KERNEL_COMPAT/CONFIG_OLD_SUNXI_KERNEL_COMPAT. -Move the code block setting P(1) for old kernels to where P gets cleared
| * | | | sunxi: dram: Use clock_get_pll5p to calculate mbus, rather then hardcodingHans de Goede2014-10-24-18/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a preparation patch for making the pll5 "p" divisor configurable through Kconfig. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | sunxi: Add clock_get_pll5p() functionHans de Goede2014-10-24-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a preparation patch for making the pll5 "p" divisor configurable through Kconfig. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sunxi: Add support for using R_UART as consoleChen-Yu Tsai2014-10-24-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The A23 only has UART0 muxed with MMC0. Some of the boards we encountered expose R_UART as a set of pads. Add support for R_UART so we can have a console while using mmc. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sunxi: Allow specifying module in prcm apb0 init functionChen-Yu Tsai2014-10-24-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The prcm apb0 controls multiple modules. Allow specifying which modules to enable clocks and de-assert resets so the function can be reused. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sunxi: Add basic A23 supportChen-Yu Tsai2014-10-24-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The basic blocks of the A23 are similar to the A31 (sun6i). Re-use sun6i code for initial clock, gpio, and uart setup. There is no SPL support for A23, as we do not have any documentation or sample code for DRAM initialization. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sunxi: Add support for uart0 on port F (mmc0)Chen-Yu Tsai2014-10-24-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allwinner SoCs provide uart0 muxed with mmc0, which can then be used with a micro SD breakout board. On the A23, this is the only way to use uart0. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sunxi: Fix reset command on sun6i/sun8iChen-Yu Tsai2014-10-24-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The watchdog on sun6i/sun8i has a different layout. Add the new layout and fix up the setup functions so that reset works. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk> [ ijc -- removed sun5i workaround from sun6i/sun8i codepath as discussed ]
| * | | | ARM: sunxi: Add basic A31 supportMaxime Ripard2014-10-24-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a new sun6i machine that supports UART and MMC. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef around mmc and smp code, drop MACH_TYPE] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sun6i: Setup the A31 UART0 muxingMaxime Ripard2014-10-24-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: commit message was "ARM: sunxi: Setup the A31 UART0 muxing"] [wens@csie.org: reorder #ifs by SUN?I] [wens@csie.org: replace magic numbers with GPIO definitions] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sun6i: Add clock supportChen-Yu Tsai2014-10-24-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the basic clocks support for the Allwinner A31 (sun6i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. This includes changes from the following commits from u-boot-sunxi: a92051b ARM: sunxi: Add sun6i clock controller structure 1f72c6f ARM: sun6i: Setup the UART0 clocks 5f2e712 ARM: sunxi: Enable pll6 by default on all models 2be2f2a ARM: sunxi-mmc: Add mmc support for sun6i / A31 12e1633 ARM: sun6i: Add initial clock setup for SPL 1a9c9c6 ARM: sunxi: Split clock code into common, sun4i and sun6i code 0b194ee ARM: sun6i: Properly setup the PLL LDO in clock_init_safe b54c626 sunxi: avoid sr32 for APB1 clock setup. 68fe29c sunxi: remove magic numbers from clock_get_pll{5,6} c89867d sunxi: clocks: clock_get_pll5 prototype and coding style 501ab1e ARM: sunxi: Fix sun6i PLL6 settings 37f669b ARM: sunxi: Fix macro names for mmc and uart reset offsets 61de1e6 ARM: sunxi: Correct comment for MBUS1 register in sun6i clock definitions Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: styling fixes reported by checkpatch.pl] [wens@csie.org: drop unsupported SPL code block and unused gpio.h header] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Cc: Tom Cubie <Mr.hipboi@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sun6i: Add support for the power reset control module found on the A31Oliver Schinagl2014-10-24-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The A31 has a new module called PRCM, or Power, Reset Control Module. This module controls clocks and resets for RTC block modules, and also PLL biasing in the main clock module. This patch adds the register definitions, and also enables the clocks and resets for the RTC block PIO (pin controller) and P2WI (push-pull 2 wire interface) which is used to talk to the PMIC. Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: spacing fixes reported by checkpatch.pl] [wens@csie.org: Use setbits helper in PRCM init function] [wens@csie.org: rephrase commit message to explain what the hardware supports and what we actually enable] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | | | ARM: sunxi: Use macro values for setting UART GPIO pull-upsChen-Yu Tsai2014-10-24-3/+3
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have already defined macros for pull-up/down values in the GPIO header. Use them instead of magic numbers when configuring the UART pins. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | Merge git://git.denx.de/u-boot-dmTom Rini2014-10-26-1/+134
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a trivial conflict over adding <dm.h> Conflicts: arch/arm/cpu/armv7/omap3/board.c Signed-off-by: Tom Rini <trini@ti.com>
| * | | | dm: serial: use Driver Model for UniPhier serial driverMasahiro Yamada2014-10-23-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit converts UniPhier on-chip serial driver to driver model. Since UniPhier SoCs do not have Device Tree support, some board files should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories. (Device Tree support for UniPhier platform is still under way.) Now the base address and master clock frequency are passed from platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and CONFIG_SYS_UNIPHIER_UART_CLK should be removed. Tested on UniPhier PH1-LD4 ref board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
| * | | | dm: omap3: Move to driver model for GPIO and serialSimon Glass2014-10-23-1/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adjust the configuration for the am33xx boards, including beagleboard, to use driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com>
| * | | | dm: am33xx: Provide platform data for serialSimon Glass2014-10-23-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Provide suitable platform data for am33xx boards, so that these boards can use driver model for serial. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
| * | | | dm: am33xx: Provide platform data for GPIOsSimon Glass2014-10-23-0/+28
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | Provide suitable platform data for am33xx boards, so that these boards can use driver model for GPIO access. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
* | | | omap3: board: add missing include and protoJeroen Hofstee2014-10-25-0/+3
| | | | | | | | | | | | | | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | | | imx: add missing includesJeroen Hofstee2014-10-25-0/+1
| | | | | | | | | | | | | | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | | | tegra: make local functions staticJeroen Hofstee2014-10-25-1/+2
| | | | | | | | | | | | | | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | | | omap3: make local functions staticJeroen Hofstee2014-10-25-3/+3
|/ / / | | | | | | | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | | Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini2014-10-23-0/+4
|\ \ \
| * | | arm: tegra: initial support for apalis t30Marcel Ziswiler2014-10-22-0/+4
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds board support for the Toradex Apalis T30 a computer on module which can be used on different carrier boards. For the sake of ease of use we do not distinguish between different carrier boards for now as the base module features are deemed sufficient enough for regular booting. The following functionality is working so far: - eMMC boot and environment storage - Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210 fixes hit mainline) - MMC/SD cards (both 8-bit as well as 4-bit slot) - USB client/host (dual role port as client e.g. for DFU/UMS, other two ports as host) Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | | kconfig: move CONFIG_USE_PRIVATE_LIBGCC to KconfigMasahiro Yamada2014-10-23-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86. Those architectures should "select" HAVE_PRIVATE_LIBGCC and CONFIG_USE_PRIVATE_LIBGCC should depend on it. Currently, this option is enabled on Tegra boards and x86 architecture. Move the definition from header files to Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com>
* | | arm: armada-xp: Add basic support for Marvell Armada XP SoCStefan Roese2014-10-23-0/+200
| |/ |/| | | | | | | | | | | | | | | | | | | This basic support for the Marvell Armada XP is base on the existing kirkwood support. Which has been generatized by moving some common files into common marvell locations. This is in preparation for the upcoming Armada XP MV78460 support. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Luka Perkov <luka@openwrt.org>
* | dm: exynos: Make sure that GPIOs are requestedSimon Glass2014-10-22-0/+3
| | | | | | | | | | | | | | | | | | | | With driver model GPIOs must be requested before use. Make sure this is done correctly. (Note that the soft SPI part of universal is omitted, since this driver is about to be replaced with a driver-model-aware version) Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-11-10 02:25:37 +0000