summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/omap5
Commit message (Collapse)AuthorAgeLines
* ARM: OMAP5 / DRA7: Setup L2 Aux Control Register with recommended configurationNishanth Menon2015-03-13-0/+16
| | | | | | | | | | | Update to existing recommendation for L2ACTLR configuration to prevent system instability and optimize performance. These apply to both OMAP5 and DRA7. Reported-by: Vivek Chengalvala <vchengalvala@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7 / OMAP5: Add workaround for ARM errata 798870Praveen Rao2015-03-13-0/+7
| | | | | | | | | | | | | | | | | | | This patch enables the workaround for ARM errata 798870 for OMAP5 / DRA7 which says "If back-to-back speculative cache line fills (fill A and fill B) are issued from the L1 data cache of a CPU to the L2 cache, the second request (fill B) is then cancelled, and the second request would have detected a hazard against a recent write or eviction (write B) to the same cache line as fill B then the L2 logic might deadlock." An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced here as well. Signed-off-by: Praveen Rao <prao@ti.com> Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7-evm: DDR3: Update leveling valuesLokesh Vutla2015-02-16-30/+30
| | | | | | | Update the software leveling parameters. This fixes the random crash seen on DRA7-evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register valueLokesh Vutla2015-02-16-3/+6
| | | | | | | | | | | The value in SDRAM_REF_CTRL controls the delay time between the initial rising edge of DDR_RESETn to rising edge of DDR_CKE (JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL should be written with a value corresponding to 500us delay before starting DDR initialization sequence, and configure proper value at the end of sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA72x: DDR3: Fix EMIF timings for 666MHz clockAngela Stegmaier2015-02-16-8/+8
| | | | | | | | | | DDR3 timing and latency paramenters were not configured correctly for 666MHz. Fixing the timing and latency values according to Data sheet. This fixes the random crashes seen on DRA72-evm. Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: DRA7xx: Add support for power rail groupingLubomir Popov2015-01-29-19/+24
| | | | | | | | | | | | | | | | | | | | | | On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC core rails. This concept of using one SMPS to supply multiple core domains (in various, although limited combinations, per primary device use case) has now become common and is used by many customer J6/J6Eco designs; it is supported by a number of corresponding PMIC OTP versions. This patch implements correct operation of the core voltages scaling routine by ensuring that each SMPS that is supplying more than one domain shall be written only once, and with the highest voltage of those fused in the SoC (or of those defined in the corresponding header if fuse read is disabled or fails) for the power rails belonging to the group. The patch also replaces some PMIC-related magic numbers with the appropriate definitions. The default OPP_NOM voltages for the DRA7xx SoCs are updated as well, per the latest DMs. Signed-off-by: Lubomir Popov <l-popov@ti.com>
* beagle_x15: add board support for Beagle x15Felipe Balbi2014-12-04-0/+4
| | | | | | | | | | | | | | | | | BeagleBoard-X15 is the next generation Open Source Hardware BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHZ A15 processor. The platform features 2GB DDR3L (w/dual 32bit busses), eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60), separate LCD port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G Ethernet. For more information, refer to: http://www.elinux.org/Beagleboard:BeagleBoard-X15 Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: omap5: sdram: mark emif_get_ext_phy_ctrl_const_regs __weakFelipe Balbi2014-12-04-1/+1
| | | | | | | | this will allow for boards to overwrite those in case memory setup is different. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: omap5: make hw_init_data weakFelipe Balbi2014-12-04-1/+1
| | | | | | | | this way we can let boards overwrite based on what they need. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: prcm: add missing registersFelipe Balbi2014-12-04-0/+3
| | | | | | | | | some boards might want to use USB1 for host, without fiddling those registers it'll be impossible. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: omap5: tps659038: rename regulator definesFelipe Balbi2014-12-04-5/+5
| | | | | | | | | Those regulators don't have any coupling with what they supply, so remove the suffixes in order to not confuse anybody. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-29-3/+0
| | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-2/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* ARM: DRA72: DDR3: Add emif settings for 666MHz clockR Sricharan2014-09-04-3/+96
| | | | | | | | On DRA72x, EMIF supports DDR3 upto 667MHz. Adding the required settings for DDR3 at 666MHz and enabling it. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* omap5: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-0/+29
| | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the OMAP5 board select menu to omap5/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="omap5"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7: Enable software leveling for dra7Sricharan R2014-08-25-31/+31
| | | | | | | | | | Currently hw leveling is enabled by default on DRA7/72. But the hardware team suggested to use sw leveling as hw leveling is not characterized and seen some test case failures. So enabling sw leveling on all DRA7 platforms. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: ctrl: Fix efuse register addressesLokesh Vutla2014-05-23-4/+4
| | | | | | | | Efuse register addresses are wrongly programmed. Fixing the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* ARM: DRA72x: Update EMIF dataLokesh Vutla2014-05-23-1/+19
| | | | | | | | DRA72 has 1GB connected to EMIF1 only. Updating the details. And also enable WA for BUG0039 only if corresponding EMIF is present. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* ARM: DRA72x: clocks: Update the hwdataLokesh Vutla2014-05-23-0/+7
| | | | | | | Adding the prcm, dplls, control module hooks for DRA72x. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* ARM: DRA72x: volt: Update the pmic offsetsKeerthy2014-05-23-0/+32
| | | | | | | | TPS65917 is used in DRA722 evm. Update the address offsets accordingly. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Tom Rini <trini@ti.com>
* ARM: DRA72x: Add Silicon ID supportLokesh Vutla2014-05-23-0/+3
| | | | | | | Add silicon ID code for DRA722 silicon. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* sizes.h - consolidate for all architecturesAlexey Brodkin2014-03-04-1/+1
| | | | | | | | | | | | | | | | Copied from Linux sources "include/linux/sizes.h" commit 413541dd66d51f791a0b169d9b9014e4f56be13c Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Stefan Roese <sr@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com> Acked-by: Stefan Roese <sr@denx.de> [trini: Add bcm Kona platforms to the patch] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-26-1/+1
|\ | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/config.mk board/ti/am43xx/mux.c include/configs/am43xx_evm.h Signed-off-by: Tom Rini <trini@ti.com>
| * DRA7: fix ABB efuse offset for OPP_NOMNishanth Menon2014-02-21-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | commit 194dd74ad919e57026f385aaab7f89acf7ea79ef (DRA7: add ABB setup for MPU voltage domain) Made an offset typo error by using 0x4A003B24 as the efuse offset for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and 0x4A003B20 is for OPP_NOM. Fix the same. Reported-by: Praveen Rao <prao@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* | kbuild: use shorten logs for mkimage rulesMasahiro Yamada2014-02-25-1/+1
|/ | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kbuild: change out-of-tree buildMasahiro Yamada2014-02-19-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit changes the working directory where the build process occurs. Before this commit, build process occurred under the source tree for both in-tree and out-of-tree build. That's why we needed to add $(obj) prefix to all generated files in makefiles like follows: $(obj)u-boot.bin: $(obj)u-boot Here, $(obj) is empty for in-tree build, whereas it points to the output directory for out-of-tree build. And our old build system changes the current working directory with "make -C <sub-dir>" syntax when descending into the sub-directories. On the other hand, Kbuild uses a different idea to handle out-of-tree build and directory descending. The build process of Kbuild always occurs under the output tree. When "O=dir/to/store/output/files" is given, the build system changes the current working directory to that directory and restarts the make. Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>" syntax for descending into sub-directories. (We can write it like "make $(obj)=<sub-dir>" with a shorthand.) This means the current working directory is always the top of the output directory. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Gerhard Sittig <gsi@denx.de>
* DRA7: add ABB setup for MPU voltage domainNishanth Menon2014-01-24-3/+18
| | | | | | | | | Patch adds modification to shared omap5 abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain at OPP_NOM. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* DRA7: Add support for ES1.1 silicon ID codeNishanth Menon2014-01-24-0/+9
| | | | | | | | ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support for ES1.1 IDCODE change. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALLJassi Brar2014-01-24-88/+0
| | | | | | | | | The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* ARM: OMAP5: clocks: Update MPU settings for OPP_NOMLokesh Vutla2013-12-12-12/+2
| | | | | | | | | | As per the latest 0.6 version of DM for OMAP5430 ES2.0, MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU should be locked at 2000MHz. Fixing the same and cleaning the previously used dpll values. Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: Change clk divider settingLokesh Vutla2013-12-12-5/+5
| | | | | | | | | Commit "armv7: hw_data: change clock divider setting" updates the setting for m6 divider for 20MHz sys_clk frequency. But missed to update for other sys_clk frequencies. Doing the same. Reported-by: Rajendran, Vinothkumar <vinothr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5+: Remove unnecessary EFUSE settingsLokesh Vutla2013-12-04-6/+0
| | | | | | | | | Certain EFUSE settings were recommended for the first four lots of OMAP5 ES1.0 silicon. These are not applicable for OMAP5 ES2.0 and DRA7 silicon. So removing these EFUSE settings. Reported-by: Griffis, Brad <bgriffis@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: Add PRCM and Control information for SATARoger Quadros2013-12-04-0/+3
| | | | | | | Adds the necessary PRCM and Control register information for SATA on DRA7xx. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: OMAP5: Add PRCM and Control information for SATARoger Quadros2013-12-04-0/+4
| | | | | | | Adds the necessary PRCM and Control register information for SATA on OMAP5. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: DRA7/OMAP5: EMIF: Add workaround for bug 0039SRICHARAN R2013-12-04-0/+68
| | | | | | | | | | | When core power domain hits oswr, then DDR3 memories does not come back while resuming. This is because when EMIF registers are lost, then the controller takes care of copying the values from the shadow registers. If the shadow registers are not updated with the right values, then this results in incorrect settings while resuming. So updating the shadow registers with the corresponding status registers here during the boot. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* ARM: DRA: EMIF: Change DDR3 settings to use hw levelingSRICHARAN R2013-12-04-68/+99
| | | | | | | | | | Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using software leveling. This was done since hardware leveling was not working. Now that the right sequence to do hw leveling is identified, use it. This is required for EMIF clockdomain to idle and come back during lowpower usecases. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* armv7: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-27/+6
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-0/+1
| | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* ARM: OMAP5: Add registers and defines for USBOTG SSDan Murphy2013-10-20-0/+4
| | | | | | | Add the prcm registers and the bit definitions to enable the USB SS port of the OMAP5 device. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* Coding Style cleanup: drop some excessive empty linesWolfgang Denk2013-10-14-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* armv7: hw_data: change clock divider setting.Poddar, Sourav2013-10-07-1/+1
| | | | | | | | | | | | | | Clock requirement for qspi clk is 192 Mhz. According to the below formulae, f dpll = f ref * 2 * m /(n + 1) clockoutx2_Hmn = f dpll / (hmn+ 1) fref = 20 Mhz, m = 96, n = 4 gives f dpll = 768 Mhz For clockoutx2_Hmn to be 768, hmn + 1 should be 4. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* omap5: add qspi supportMatt Porter2013-10-07-0/+9
| | | | | | | | Add QSPI definitions and clock configuration support. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* ARM: OMAP5: Avoid writing into LDO SRAM bitsLokesh Vutla2013-09-20-12/+0
| | | | | | | | | | | Writing magic bits into LDO SRAM was suggested only for OMAP5432 ES1.0. Now these are no longer applicable. Moreover these bits should not be overwritten as they are loaded from EFUSE. So avoid writing into these registers. Boot tested on OMAP5432 ES2.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: Add CPSW support to DRA7xx EVMMugunthan V N2013-07-26-0/+4
| | | | | | Adding support for CPSW Ethernet support found in DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: DRA7xx: Enable GMAC clock controlMugunthan V N2013-07-26-1/+8
| | | | | | Enabling CPSW module by enabling GMAC clock control Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: DRA7xx: Lock DPLL_GMACLokesh Vutla2013-07-26-0/+12
| | | | | | | | | Locking DPLL_GMAC [mugunthanvnm@ti.com:Configure only if CPSW is selected] Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-136/+8
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP: GPIO: Fix valid range and enable usage of all GPIOs on OMAP5Axel Lin2013-07-02-1/+5
| | | | | | | | | | | | | | | | The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs. These SoCs have different gpio count but currently omap_gpio driver uses hard coded 192 which is wrong. This patch fixes this issue by: 1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h. 2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5. Thanks for Lubomir Popov to provide valuable comments to fix this issue. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Acked-by: Heiko Schocher <hs@denx.de>
* OMAP5: Enable access to auxclk registersLubomir Popov2013-06-10-0/+8
| | | | | | | | | | auxclk0 and auxclk1 are utilized on some OMAP5 boards. Define the infrastructure needed for accessing them without using magic numbers. Also remove unrelated TPS62361 defines from clocks.h Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
* ARM: DRA7xx: EMIF: Change settings required for EVM boardSricharan R2013-06-10-21/+190
| | | | | | | | | | | DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit v1.1 at 2024-11-19 19:18:33 +0000