summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/omap5
Commit message (Collapse)AuthorAgeLines
* ARM: DRA7xx: Add CPSW support to DRA7xx EVMMugunthan V N2013-07-26-0/+4
| | | | | | Adding support for CPSW Ethernet support found in DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: DRA7xx: Enable GMAC clock controlMugunthan V N2013-07-26-1/+8
| | | | | | Enabling CPSW module by enabling GMAC clock control Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: DRA7xx: Lock DPLL_GMACLokesh Vutla2013-07-26-0/+12
| | | | | | | | | Locking DPLL_GMAC [mugunthanvnm@ti.com:Configure only if CPSW is selected] Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-136/+8
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP: GPIO: Fix valid range and enable usage of all GPIOs on OMAP5Axel Lin2013-07-02-1/+5
| | | | | | | | | | | | | | | | The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs. These SoCs have different gpio count but currently omap_gpio driver uses hard coded 192 which is wrong. This patch fixes this issue by: 1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h. 2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5. Thanks for Lubomir Popov to provide valuable comments to fix this issue. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Acked-by: Heiko Schocher <hs@denx.de>
* OMAP5: Enable access to auxclk registersLubomir Popov2013-06-10-0/+8
| | | | | | | | | | auxclk0 and auxclk1 are utilized on some OMAP5 boards. Define the infrastructure needed for accessing them without using magic numbers. Also remove unrelated TPS62361 defines from clocks.h Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
* ARM: DRA7xx: EMIF: Change settings required for EVM boardSricharan R2013-06-10-21/+190
| | | | | | | | | | | DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: clocks: Update PLL valuesLokesh Vutla2013-06-10-34/+54
| | | | | | | | | | | Update PLL values. SYS_CLKSEL value for 20MHz is changed to 2. In other platforms SYS_CLKSEL value 2 represents reserved. But in sys_clk array ind 1 is used for 13Mhz. Since other platforms are not using 13Mhz, reusing index 1 for 20MHz. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Sricharan R <r.sricharan@ti.com>
* ARM: DRA7xx: Do not enable srcomp for DRA7xx Soc'sLokesh Vutla2013-06-10-0/+3
| | | | | | | | Slew rate compensation cells are not present for DRA7xx Soc's. So return from function srcomp_enable() if soc is not OMAP54xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: DRA7xx: support class 0 optimized voltagesNishanth Menon2013-06-10-0/+10
| | | | | | | | | | | | | DRA752 now uses AVS Class 0 voltages which are voltages in efuse. This means that we can now use the optimized voltages which are stored as mV values in efuse and program PMIC accordingly. This allows us to go with higher OPP as needed in the system without the need for implementing complex AVS logic. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: power Add support for tps659038 PMICLokesh Vutla2013-06-10-1/+37
| | | | | | | | TPS659038 is the power IC used in DRA7XX boards. Adding support for this and also adding pmic data for DRA7XX boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP4+: pmic: Make generic bus init and write functionsLokesh Vutla2013-06-10-0/+3
| | | | | | | | | | Voltage scaling can be done in two ways: -> Using SR I2C -> Using GP I2C In order to support both, have a function pointer in pmic_data so that we can call as per our requirement. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.hLokesh Vutla2013-06-10-2/+2
| | | | | | | To be consistent with other ARM platforms, renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: clocks: Do not enable sgx clocksSricharan R2013-06-10-6/+0
| | | | | | | | SGX clocks should be enabled only for OMAP5 ES1.0. So this can be removed. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP4+: Cleanup header filesLokesh Vutla2013-06-10-0/+2
| | | | | | | After having the u-boot clean up series, there are many definitions that are unused in header files. Removing all those unused ones. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: Fix bug in omap5_es1_prcm structLubomir Popov2013-06-10-0/+1
| | | | | | | | | | | | | | The newly introduced function setup_warmreset_time(), called from within prcm_init(), tries to write to the prm_rsttime OMAP5 register. The struct member holding this register's address is however initialized for OMAP5 ES2.0 only. On ES1.0 devices this uninitialized value causes a second (warm) reset at startup. Add .prm_rsttime address init to the ES1.0 struct. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> Acked-by: Tom Rini <trini@ti.com>
* OMAP5: add ABB setup for MPU voltage domainAndrii Tseglytskyi2013-06-10-0/+7
| | | | | | | | Patch adds a call of abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain. Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
* OMAP3+: introduce generic ABB supportAndrii Tseglytskyi2013-06-10-0/+68
| | | | | | | | | | | | | | | | | Adaptive Body Biasing (ABB) modulates transistor bias voltages dynamically in order to optimize switching speed versus leakage. Adaptive Body-Bias ldos are present for some voltage domains starting with OMAP3630. There are three modes of operation: * Bypass - the default, it just follows the vdd voltage * Foward Body-Bias - applies voltage bias to increase transistor performance at the cost of power. Used to operate safely at high OPPs. * Reverse Body-Bias - applies voltage bias to decrease leakage and save power. Used to save power at lower OPPs. Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com> Acked-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP4/5: Make OMAPx_SRAM_SCRATCH_ defines commonSRICHARAN R2013-05-10-4/+5
| | | | | | | | These defines are same across OMAP4/5. So move them to omap_common.h. This is required for the patches that follow. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* ARM: OMAP5: Fix warm reset with USB cable connectedLokesh Vutla2013-05-10-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Warm reset on OMAP5 freezes when USB cable is connected. Fix requires PRM_RSTTIME.RSTTIME1 to be programmed with the time for which reset should be held low for the voltages and the oscillator to reach stable state. There are 3 parameters to be considered for calculating the time, which are mostly board and PMIC dependent. -1- Time taken by the Oscillator to shut + restart -2- PMIC OTP times -3- Voltage rail ramp times, which inturn depends on the PMIC slew rate and value of the voltage ramp needed. In order to keep the code in u-boot simple, have a way for boards to specify a pre computed time directly using the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' option. If boards fail to specify the time, use a default as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead. Using the default value translates into some ~22ms and should work in all cases. However in order to avoid this large delay hiding other bugs, its recommended that all boards look at their respective data sheets and specify a pre computed and optimal value using 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' In order to help future board additions to compute this config option value, add a README at doc/README.omap-reset-time which explains how to compute the value. Also update the toplevel README with the additional option and pointers to doc/README.omap-reset-time. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [rnayak@ti.com: Updated changelog and added the README] Signed-off-by: Rajendra Nayak <rnayak@ti.com>
* OMAP5: USB: hsusbtll_clkctrl has to be in hw_auto for USB to workLubomir Popov2013-05-10-1/+1
| | | | | | | | | | | | USB TLL clocks do not support 'explicit_en', only 'hw_auto' control (R. Sricharan). cm_l3init_hsusbtll_clkctrl has to be moved to the clk_modules_hw_auto_essential[] array in order to make the clock work. This fix is needed (but not sufficient) for USB EHCI operation in U-Boot. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
* OMAP5: I2C: Enable i2c5 clocksLubomir Popov2013-05-10-0/+1
| | | | | | | I2C4 and I2C5 are utilized on all known OMAP5 hardware platforms. The i2c5 clock was however not enabled; do this here. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
* arm: omap4: Fix SDRAM AUTO DETECTIONLokesh Vutla2013-04-08-1/+0
| | | | | | | | | | | | | | Commit "8602114 omap: emif: configure emif only when required" breaks SDRAM_AUTO_DETECTION. The issue is dmm_init() depends on emif_sizes[](SDRAM Auto detection) done in do_sdram_init(). The above commit moves dmm_init() above do_sdram_init() because of which dmm_init() uses uninitialized emif_sizes[]. So instead of using global emif_sizes[], get sdram details locally and calculate emif sizes. Reported-by: Michael Cashwell <mboards@prograde.net> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* arm: dra7xx: Add silicon id support for DRA752 socLokesh Vutla2013-03-11-0/+3
| | | | | | | | Adding CPU detection support for the DRA752 ES1.0 soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: Add DDR related data for DRA752 ES1.0Lokesh Vutla2013-03-11-2/+25
| | | | | | | | | | DRA752 uses DDR3. Populating the corresponding structures with DDR3 data. Writing into MA registers if only MA is present in that soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: Add control module changesLokesh Vutla2013-03-11-2/+75
| | | | | | | | | | Control module register addresses are changed from OMAP5 to DRA7XX socs. So adding the necessary changes for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: clock: Add the dplls dataLokesh Vutla2013-03-11-3/+61
| | | | | | | | | | | | A new DPLL DDR is added in DRA7XX socs. Now clocks to EMIF CD is from DPLL DDR. So DPLL DDR should be locked before initializing RAM. Also adding other dpll data which are different from OMAP5 ES2.0. SYS_CLK running at 20MHz is introduced in DRA7xx socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: clock: Add the prcm changesLokesh Vutla2013-03-11-5/+234
| | | | | | | | PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX. So adding the necessary register changes for DRA7XX socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP5: srcomp: enable slew rate compensation cells after powerupLokesh Vutla2013-03-11-1/+120
| | | | | | | | | | | | | | After power-up SRCOMP cells are by-passed by default in OMAP5. Software has to enable these SRCOMP sells. For ES2: All 5 SRCOMP cells needs to be enabled. For ES1: Only 4 SRCOMP cells in core power domain are enabled. The 1 in wkup domain is not enabled because smart i/os of wkup domain work with default compensation code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP5: Add DDR changes required for OMAP543X ES2.0 SOCsLokesh Vutla2013-03-11-2/+87
| | | | | | | | | | | | | Add pre calculated timing settings of LPDDR2 and DDR3 memories present in OMAP5430 and OMAP5432 ES2.0 versions. Also adding the DDR pad io settings required for OMAP543X SOCs here. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP4/5: clocks: Add the required OPP settings as per the latest addendumSRICHARAN R2013-03-11-99/+136
| | | | | | | | | | | | | | | | | Change OPP settings as per the latest 0.5 version of addendum for OMAP5430 ES2.0. omap4/hw_data.c is touched here to add dummy dividers. While here correcting OPP_NOM mpu, core frequency for OMAP4430 ES2.x Note that OMAP5430 ES1.0 support is still kept alive and would be removed in a cleanup later. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
* ARM: OMAP5: clock: Add the prcm register changes required for ES2.0SRICHARAN R2013-03-11-0/+288
| | | | | | | | | | | PRCM register addresses are changed from ES1.0 to ES2.0 due to PER power domain getting moved to CORE power domain. So adding the nessecary register changes for the same. Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP5: Add silicon id support for ES2.0 revision.SRICHARAN R2013-03-11-11/+16
| | | | | | | | | Adding the CPU detection suport for OMAP5430 and OMAP5432 ES2.0 SOCs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
* ARM: OMAP5: Clean up iosettings codeLokesh Vutla2013-03-11-44/+67
| | | | | | | | | | | There is some code duplication in the ddr io settings code. This is avoided by moving the data to a Soc specific place and letting the code generic. This avoids unnessecary code addition for future socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Make control module register structure genericLokesh Vutla2013-03-11-56/+124
| | | | | | | | | | | | A seperate omap_sys_ctrl_regs structure is defined for omap4 & 5. If there is any change in control module for any of the ES versions, a new structure needs to be created. In order to remove this dependency, making the register structure generic for all the omap4+ boards. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Cleanup emif specific filesLokesh Vutla2013-03-11-42/+77
| | | | | | | | | | | | Removing the duplicated code in ddr3 initialization. Also creating structure for lpddr2 mode registers to avoid unnessecary revision checks. These change reduces code addition for future Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Clean up the pmic codeSRICHARAN R2013-03-11-99/+43
| | | | | | | | | | The pmic code is duplicated for OMAP 4 and 5. Instead move the data to Soc specific place and share the code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Cleanup the clocks layerSRICHARAN R2013-03-11-396/+355
| | | | | | | | | | | | | | | Currently there is quite a lot of code which is duplicated in the clocks code for OMAP 4 and 5 Socs. Avoiding this here by moving the clocks data to a SOC specific place and the sharing the common code. This helps in addition of a new Soc with minimal changes. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Change the PRCM structure prototype common for all SocsSRICHARAN R2013-03-11-108/+453
| | | | | | | | | | | | The current PRCM structure prototype directly matches the hardware register layout. So there is a need to change this for every new silicon revision which has register space changes. Avoiding this by making the prototye generic and populating the register addresses seperately for all Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP4+: emif: Detect SDRAM from SDRAM config registerLokesh Vutla2013-03-11-2/+3
| | | | | | | | | | | Now SDRAM initialization is done on the basis of omap revision. Instead this should be done on basis of SDRAM type read from EMIF_SDRAM_CONFIG register. This will be helpful to avoid unnessecary cpu checks for new boards Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4/5: Move USB clocks to essential group.SRICHARAN R2012-07-07-3/+3
| | | | | | | | | USB clocks will be required for fastboot, tftp related functionalities. Move these clocks to essential group inorder to have the functionality working when non-essential clocks are not enabled. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4/5: Move gpmc clocks to essential group.SRICHARAN R2012-07-07-1/+1
| | | | | | | | | | GPMC clocks are currently getting enabled as a part non-essential clocks. This will be required during NOR boot. Move this to essential group to keep the functionality, when non-essential clocks are not enabled. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4+: Move external phy initialisations to arch specific place.SRICHARAN R2012-07-07-0/+31
| | | | | | | | | | The external phy is present in the case OMAP5 soc is currently configured in emif-common.c. This results in having dummy structures for those Socs which do not have a external phy. So by having a weak function in emif-common and overriding it in OMAP5, avoids the use of dummy structures. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: Change voltages for omap5432Lokesh Vutla2012-07-07-10/+21
| | | | | | Change voltages for OMAP5432 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: EMIF: Add support for DDR3 deviceLokesh Vutla2012-07-07-0/+15
| | | | | | | | | In OMAP5432 EMIF controlller supports DDR3 device. This patch adds support for ddr3 device intialization and configuration. Initialization sequence is done as specified in JEDEC specs. This also adds support for ddr3 leveling. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: ADD precalculated timings for ddr3Lokesh Vutla2012-07-07-1/+49
| | | | | | | Adding precalculated timings for ddr3 with 1cs adding required registers for ddr3 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: Configure the io settings for omap5432 uevm boardLokesh Vutla2012-07-07-19/+79
| | | | | | This patch adds the IO settings required for OMAP5432 uevm's DDR3 pads Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: ADD chip detection for OMAP5432 SOCLokesh Vutla2012-07-07-1/+9
| | | | | | This patch adds chip detection for OMAP5432 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: dmm: Create a tiler trap section.SRICHARAN R2012-07-07-3/+3
| | | | | | | | | | | | | | | | | The unmapped entries in tiler space are set with values 0xFF. So creating a DMM section of size 16MB at 0xFF000000 with ADDRSPACE set to 0x2. This way all the unmapped entry accesses to tiler will be trapped by the EMIF and a error response is sent to the L3 interconnect. L3 errors are inturn reported to MPU. Note that here the tiler trap section is overlapping with the actual ddr physical space and we lose 16MB out of the total 2GB. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: reset: Use cold reset in case of 5430ES1.0SRICHARAN R2012-05-15-0/+14
| | | | | | | | Warm reset is not functional in case of omap5430ES1.0. So override the weak reset_cpu function to use cold reset instead. Signed-off-by: R Sricharan <r.sricharan@ti.com>