summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/omap5/prcm-regs.c
Commit message (Collapse)AuthorAgeLines
* ARM: BeagleBoard-x15: Enable i2c5 clocksLokesh Vutla2015-06-15-0/+4
| | | | | | | | | On AM57xx evm I2C5 is used to detect the LCD board by reading the EEPROM present on the bus. Enable i2c5 clocks to help that. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Add support for IO delay configurationLokesh Vutla2015-06-12-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | On DRA7, in addition to the regular muxing of pins, an additional hardware module called IODelay which is also expected to be configured. This "IODelay" module has it's own register space that is independent of the control module. It is advocated strongly in TI's official documentation considering the existing design of the DRA7 family of processors during mux or IODelay recalibration, there is a potential for a significant glitch which may cause functional impairment to certain hardware. It is hence recommended to do muxing as part of IOdelay recalibration. IODELAY recalibration sequence: - Complete AVS voltage change on VDD_CORE_L - Unlock IODLAY config registers. - Perform IO delay calibration with predefined values. - Isolate all the IOs - Update the delay mechanism for each IO with new calibrated values. - Configure PAD configuration registers - De-isolate all the IOs. - Relock IODELAY config registers. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: DRA7: Set serial number environment variableDileep Katta2015-04-23-0/+4
| | | | | | | | | | | | | | | | | This patch populates serial number environment variable from die_id_0 and die_id_1 register values for DRA7xx boards. The function is added in omap common code so that this can be re-used. Serial# environment variable will be useful to show correct information in "fastboot devices" commands. Ref: http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Enable clocks for USB OTGSS and USB PHYKishon Vijay Abraham I2015-04-14-5/+5
| | | | | | | Enabled clocks for dwc3 controller and USB PHY present in DRA7. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
* arm: dra7xx: prcm: add missing registersFelipe Balbi2014-12-04-0/+3
| | | | | | | | | some boards might want to use USB1 for host, without fiddling those registers it'll be impossible. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: ctrl: Fix efuse register addressesLokesh Vutla2014-05-23-4/+4
| | | | | | | | Efuse register addresses are wrongly programmed. Fixing the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* DRA7: fix ABB efuse offset for OPP_NOMNishanth Menon2014-02-21-1/+1
| | | | | | | | | | | | commit 194dd74ad919e57026f385aaab7f89acf7ea79ef (DRA7: add ABB setup for MPU voltage domain) Made an offset typo error by using 0x4A003B24 as the efuse offset for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and 0x4A003B20 is for OPP_NOM. Fix the same. Reported-by: Praveen Rao <prao@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* DRA7: add ABB setup for MPU voltage domainNishanth Menon2014-01-24-0/+8
| | | | | | | | | Patch adds modification to shared omap5 abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain at OPP_NOM. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: Add PRCM and Control information for SATARoger Quadros2013-12-04-0/+3
| | | | | | | Adds the necessary PRCM and Control register information for SATA on DRA7xx. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: OMAP5: Add PRCM and Control information for SATARoger Quadros2013-12-04-0/+4
| | | | | | | Adds the necessary PRCM and Control register information for SATA on OMAP5. Signed-off-by: Roger Quadros <rogerq@ti.com>
* usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-0/+1
| | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* ARM: OMAP5: Add registers and defines for USBOTG SSDan Murphy2013-10-20-0/+4
| | | | | | | Add the prcm registers and the bit definitions to enable the USB SS port of the OMAP5 device. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* Coding Style cleanup: drop some excessive empty linesWolfgang Denk2013-10-14-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* omap5: add qspi supportMatt Porter2013-10-07-0/+1
| | | | | | | | Add QSPI definitions and clock configuration support. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* ARM: OMAP5: Avoid writing into LDO SRAM bitsLokesh Vutla2013-09-20-12/+0
| | | | | | | | | | | Writing magic bits into LDO SRAM was suggested only for OMAP5432 ES1.0. Now these are no longer applicable. Moreover these bits should not be overwritten as they are loaded from EFUSE. So avoid writing into these registers. Boot tested on OMAP5432 ES2.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: Add CPSW support to DRA7xx EVMMugunthan V N2013-07-26-0/+4
| | | | | | Adding support for CPSW Ethernet support found in DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: DRA7xx: Enable GMAC clock controlMugunthan V N2013-07-26-0/+2
| | | | | | Enabling CPSW module by enabling GMAC clock control Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: DRA7xx: Lock DPLL_GMACLokesh Vutla2013-07-26-0/+1
| | | | | | | | | Locking DPLL_GMAC [mugunthanvnm@ti.com:Configure only if CPSW is selected] Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* OMAP5: Enable access to auxclk registersLubomir Popov2013-06-10-0/+8
| | | | | | | | | | auxclk0 and auxclk1 are utilized on some OMAP5 boards. Define the infrastructure needed for accessing them without using magic numbers. Also remove unrelated TPS62361 defines from clocks.h Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
* ARM: DRA7xx: EMIF: Change settings required for EVM boardSricharan R2013-06-10-0/+1
| | | | | | | | | | | DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7xx: clocks: Update PLL valuesLokesh Vutla2013-06-10-0/+1
| | | | | | | | | | | Update PLL values. SYS_CLKSEL value for 20MHz is changed to 2. In other platforms SYS_CLKSEL value 2 represents reserved. But in sys_clk array ind 1 is used for 13Mhz. Since other platforms are not using 13Mhz, reusing index 1 for 20MHz. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Sricharan R <r.sricharan@ti.com>
* ARM: OMAP4+: Cleanup header filesLokesh Vutla2013-06-10-0/+2
| | | | | | | After having the u-boot clean up series, there are many definitions that are unused in header files. Removing all those unused ones. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: Fix bug in omap5_es1_prcm structLubomir Popov2013-06-10-0/+1
| | | | | | | | | | | | | | The newly introduced function setup_warmreset_time(), called from within prcm_init(), tries to write to the prm_rsttime OMAP5 register. The struct member holding this register's address is however initialized for OMAP5 ES2.0 only. On ES1.0 devices this uninitialized value causes a second (warm) reset at startup. Add .prm_rsttime address init to the ES1.0 struct. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> Acked-by: Tom Rini <trini@ti.com>
* OMAP5: add ABB setup for MPU voltage domainAndrii Tseglytskyi2013-06-10-0/+7
| | | | | | | | Patch adds a call of abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain. Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
* ARM: OMAP5: Fix warm reset with USB cable connectedLokesh Vutla2013-05-10-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Warm reset on OMAP5 freezes when USB cable is connected. Fix requires PRM_RSTTIME.RSTTIME1 to be programmed with the time for which reset should be held low for the voltages and the oscillator to reach stable state. There are 3 parameters to be considered for calculating the time, which are mostly board and PMIC dependent. -1- Time taken by the Oscillator to shut + restart -2- PMIC OTP times -3- Voltage rail ramp times, which inturn depends on the PMIC slew rate and value of the voltage ramp needed. In order to keep the code in u-boot simple, have a way for boards to specify a pre computed time directly using the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' option. If boards fail to specify the time, use a default as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead. Using the default value translates into some ~22ms and should work in all cases. However in order to avoid this large delay hiding other bugs, its recommended that all boards look at their respective data sheets and specify a pre computed and optimal value using 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' In order to help future board additions to compute this config option value, add a README at doc/README.omap-reset-time which explains how to compute the value. Also update the toplevel README with the additional option and pointers to doc/README.omap-reset-time. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [rnayak@ti.com: Updated changelog and added the README] Signed-off-by: Rajendra Nayak <rnayak@ti.com>
* arm: dra7xx: Add control module changesLokesh Vutla2013-03-11-0/+72
| | | | | | | | | | Control module register addresses are changed from OMAP5 to DRA7XX socs. So adding the necessary changes for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: dra7xx: clock: Add the prcm changesLokesh Vutla2013-03-11-2/+222
| | | | | | | | PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX. So adding the necessary register changes for DRA7XX socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP5: srcomp: enable slew rate compensation cells after powerupLokesh Vutla2013-03-11-1/+4
| | | | | | | | | | | | | | After power-up SRCOMP cells are by-passed by default in OMAP5. Software has to enable these SRCOMP sells. For ES2: All 5 SRCOMP cells needs to be enabled. For ES1: Only 4 SRCOMP cells in core power domain are enabled. The 1 in wkup domain is not enabled because smart i/os of wkup domain work with default compensation code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP5: clock: Add the prcm register changes required for ES2.0SRICHARAN R2013-03-11-0/+283
| | | | | | | | | | | PRCM register addresses are changed from ES1.0 to ES2.0 due to PER power domain getting moved to CORE power domain. So adding the nessecary register changes for the same. Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Make control module register structure genericLokesh Vutla2013-03-11-0/+74
| | | | | | | | | | | | A seperate omap_sys_ctrl_regs structure is defined for omap4 & 5. If there is any change in control module for any of the ES versions, a new structure needs to be created. In order to remove this dependency, making the register structure generic for all the omap4+ boards. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Change the PRCM structure prototype common for all SocsSRICHARAN R2013-03-11-0/+306
The current PRCM structure prototype directly matches the hardware register layout. So there is a need to change this for every new silicon revision which has register space changes. Avoiding this by making the prototye generic and populating the register addresses seperately for all Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>