summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/omap-common
Commit message (Collapse)AuthorAgeLines
* omap-common: Common get_board_serial function to pass serial through ATAGPaul Kocialkowski2015-10-22-0/+18
| | | | | | | | | Since there is a common function to grab the serial number from the die id bits, it makes sense have one to parse that serial number and feed it to the serial ATAG. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap-common: Common function to display die id, replacing omap3-specific versionPaul Kocialkowski2015-10-22-0/+10
| | | | | | | | | This introduces omap_die_id_display to display the full die id. There is no need to store it in an environment variable, that no boot script is using anyway. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap-common: Common serial and usbethaddr functions based on die idPaul Kocialkowski2015-10-22-22/+27
| | | | | | | | | Now that we have a common prototype to grab the omap die id, functions to figure out a serial number and usb ethernet address can use it directly. Those also get an omap_die_id prefix for better consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap-common: Common omap_die_id definitionPaul Kocialkowski2015-10-22-0/+5
| | | | | | | | This introduces a common definition for omap_die_id, that aims at providing a common interface for accessing omap platform's die id bits. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: emif: Fix disabling/enabling of refreshesLokesh Vutla2015-09-11-3/+3
| | | | | | | | | clrsetbits_le32/clrbits_le32 takes mask of the bits as input that are needed to be set/clear. But emif driver passes the shift of the bits. Fixing it here. Reported-by: Mark Mckeown <m-mckeown@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* omap-common: SYS_BOOT fallback logic correction and support for more devicesPaul Kocialkowski2015-08-28-10/+22
| | | | | | | | | | | | | | | | | | | | | The SYS_BOOT-based fallback shouldn't only check for one of the conditions of use and then let the switch/case handle each boot device without enforcing the conditions for each type of boot device again. For instance, this behaviour would trigger the fallback for UART when BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not CONFIG_SPL_USB_SUPPORT. Separating the logic for USB and UART solves this. In addition, this adds support for more peripheral devices (USBETH and CPGMAC) to the fallback mechanism. Note that the USBETH boot device should always be different from the USB boot device (each should match a different bootrom handoff case). Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
* ARM: OMAP5: Add support for disabling clocks in ubootKishon Vijay Abraham I2015-08-17-0/+53
| | | | | | | | | Add do_disable_clocks() to disable clock domains and module clocks. These clocks are enabled using do_enable_clocks(). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* omap-common: SYS_BOOT-based fallback boot device selection for peripheral bootPaul Kocialkowski2015-07-27-7/+45
| | | | | | | | | | | | | | | | | OMAP devices might boot from peripheral devices, such as UART or USB. When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot) from that peripheral device, but in most cases, this is not a valid boot device. This introduces a fallback option that reads the SYS_BOOT pins, that are used by the bootrom to determine which device to boot from. It is intended for the SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the U-Boot SPL can load the next stage from a valid location. Practically, this options allows loading the U-Boot SPL through USB and have it load the next stage according to the memory device selected by SYS_BOOT instead of stalling. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* omap-common: Boot device define instead of hardcoded valuePaul Kocialkowski2015-07-27-2/+2
| | | | | | | Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4 instead of a hardcoded value. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* omap-common: Common boot code OMAP3 support and cleanupPaul Kocialkowski2015-07-27-55/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This introduces OMAP3 support for the common omap boot code, as well as a major cleanup of the common omap boot code. First, the omap_boot_parameters structure becomes platform-specific, since its definition differs a bit across omap platforms. The offsets are removed as well since it is U-Boot's coding style to use structures for mapping such kind of data (in the sense that it is similar to registers). It is correct to assume that romcode structure encoding is the same as U-Boot, given the description of these structures in the TRMs. The original address provided by the bootrom is passed to the U-Boot binary instead of a duplicate of the structure stored in global data. This allows to have only the relevant (boot device and mode) information stored in global data. It is also expected that the address where the bootrom stores that information is not overridden by the U-Boot SPL or U-Boot. The save_omap_boot_params is expected to handle all special cases where the data provided by the bootrom cannot be used as-is, so that spl_boot_device and spl_boot_mode only return the data from global data. All of this is only relevant when the U-Boot SPL is used. In cases it is not, save_boot_params should fallback to its weak (or board-specific) definition. save_omap_boot_params should not be called in that context either. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* usb: Fastboot function config for better consistency with other functionsPaul Kocialkowski2015-07-22-1/+1
| | | | | | | | | | | | USB download gadget functions such as thor and dfu have a separate config option for the USB gadget part of the code, independent from the command part. This switches the fastboot USB gadget to the same scheme, for better consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
* ARM: DRA7: emif: Fix DDR init sequence during warm resetLokesh Vutla2015-06-15-2/+2
| | | | | | | | | Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after warm reset, emif needs to be configured to bring it back to a known state. So configure EMIF during warm reset. Reported-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* am33xx: Re-enable SW levelling for DDR2Tom Rini2015-06-15-4/+9
| | | | | | | | | | | | | The recent changes for hw leveling on am33xx were not intended for DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config value to check against. This lets us pass in the value we would use to configure, when we have not yet configured the board yet. In other cases update the call to be as functional as before and check an already programmed value in. Tested-by: Yan Liu <yan-liu@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7: Add support for IO delay configurationLokesh Vutla2015-06-12-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | On DRA7, in addition to the regular muxing of pins, an additional hardware module called IODelay which is also expected to be configured. This "IODelay" module has it's own register space that is independent of the control module. It is advocated strongly in TI's official documentation considering the existing design of the DRA7 family of processors during mux or IODelay recalibration, there is a potential for a significant glitch which may cause functional impairment to certain hardware. It is hence recommended to do muxing as part of IOdelay recalibration. IODELAY recalibration sequence: - Complete AVS voltage change on VDD_CORE_L - Unlock IODLAY config registers. - Perform IO delay calibration with predefined values. - Isolate all the IOs - Update the delay mechanism for each IO with new calibrated values. - Configure PAD configuration registers - De-isolate all the IOs. - Relock IODELAY config registers. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: DRA7: DDR3: Add support for HW levelingLokesh Vutla2015-06-12-21/+125
| | | | | | | | DRA7 EMIF supports Full leveling for DDR3. Adding support for the Full leveling sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* fastboot: ARM: OMAP5: Enable reboot-bootloaderDileep Katta2015-04-23-0/+10
| | | | | | | | | | | | | | | | | | | | | | Implemented fb_set_reboot_flag() for OMAP5 to set an environment variable 'dofastboot' when reboot-bootloader called. This environment variable will be checked in boot command and fastboot will be called if the variable is set. If the bootcmd env variable of OMAP5 common is overwritten with board-specific command, then these changes will not apply. This was originally intended for DRA7 platform, but now applies to all OMAP5. Ref: http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=19da2e436e9806259cf1f4988b9e046ab256bf2c Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Make it check for !CONFIG_ENV_IS_NOWHERE as we can't saveenv() in that case] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Set serial number environment variableDileep Katta2015-04-23-0/+13
| | | | | | | | | | | | | | | | | This patch populates serial number environment variable from die_id_0 and die_id_1 register values for DRA7xx boards. The function is added in omap common code so that this can be re-used. Serial# environment variable will be useful to show correct information in "fastboot devices" commands. Ref: http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* ahci: mmio_base is a virtual addressScott Wood2015-04-18-4/+4
| | | | | | | | | | | | | | Don't store it in a u32. Don't dereference the bus address as if it were a virtual address (fixes 284231e49a2b4 ("ahci: Support splitting of read transactions into multiple chunks")). Fixes crash on boot in MPC8641HPCN_36BIT target. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Vadim Bendebury <vbendeb@chromium.org> Acked-by: York Sun <yorksun@freescale.com>
* ARM: OMAP3: Get rid of omap3_gp_romcode_call and replace with omap_smc1Nishanth Menon2015-03-13-1/+3
| | | | | | | | | | | | omap_smc1 is now generic enough to remove duplicate omap3_gp_romcode_call logic that omap3 introduced. As part of this change, move to using the generic lowlevel_init.S for omap3 as well. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP: Change set_pl310_ctrl_reg to be genericNishanth Menon2015-03-13-7/+11
| | | | | | | | | | | | | | | | | | | set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup PL310 control register, however, that is something that is generic enough to be used for OMAP5 generation of processors as well. The only difference being the service being invoked for the function. So, convert the service to a macro and use a generic name (same as that used in Linux for some consistency). While at that, also add a data barrier which is necessary as per recommendation. While at this, smc #0 is maintained as handcoded assembly thanks to various gcc version eccentricities, discussion thread: http://marc.info/?t=142542166800001&r=1&w=2 Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ti: armv7: Move SPL SDRAM init to the right place, drop unused CONFIG_SPL_STACKSimon Glass2015-03-04-1/+5
| | | | | | | | | | | | | | | | | | | Currently in some cases SDRAM init requires global_data to be available and soon this will not be available prior to board_init_f(). Adjust the code paths in these cases to be correct. In some cases we had the SPL stack be in DDR as we might have large stacks (due to Falcon Mode + Environment). In these cases switch to CONFIG_SPL_STACK_R. In other cases we had simply been setting CONFIG_SPL_STACK into SRAM. In these cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also in SRAM) so drop those lines. Signed-off-by: Simon Glass <sjg@chromium.org> Tested on Beagleboard, Beagleboard xM Tested-by: Matt Porter <mporter@konsulko.com> Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard Tested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2015-02-17-1/+1
|\
| * arm: Allow lr to be saved by board codeSimon Glass2015-02-16-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The link register value can be required on some boards (e.g. FEL mode on sunxi) so use a branch instruction to jump to save_boot_params() instead of a branch link. This requires a branch back to save_boot_params_ret so adjust the users to deal with this. For exynos just drop the function since it doesn't do anything. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register valueLokesh Vutla2015-02-16-1/+3
|/ | | | | | | | | | | The value in SDRAM_REF_CTRL controls the delay time between the initial rising edge of DDR_RESETn to rising edge of DDR_CKE (JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL should be written with a value corresponding to 500us delay before starting DDR initialization sequence, and configure proper value at the end of sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: DRA7xx: Add support for power rail groupingLubomir Popov2015-01-29-6/+77
| | | | | | | | | | | | | | | | | | | | | | On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC core rails. This concept of using one SMPS to supply multiple core domains (in various, although limited combinations, per primary device use case) has now become common and is used by many customer J6/J6Eco designs; it is supported by a number of corresponding PMIC OTP versions. This patch implements correct operation of the core voltages scaling routine by ensuring that each SMPS that is supplying more than one domain shall be written only once, and with the highest voltage of those fused in the SoC (or of those defined in the corresponding header if fuse read is disabled or fails) for the power rails belonging to the group. The patch also replaces some PMIC-related magic numbers with the appropriate definitions. The default OPP_NOM voltages for the DRA7xx SoCs are updated as well, per the latest DMs. Signed-off-by: Lubomir Popov <l-popov@ti.com>
* TI ARMv7: Don't use GD before crt0.S has set itTom Rini2015-01-16-11/+10
| | | | | | | | | | | | | | | | | Prior to this change we set the gd pointer early so that we can store data in it. This becomes problematic for DM changes as well as being odd in general. Re-work the code paths so that we don't need to set the gd pointer so early and instead can rely upon the normal setting of it. In order to do this we do need to move certain calls from s_init into spl_board_init(), mainly preloader_console_init and save_omap_boot_params. Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM, OMAP5 uEVM, DRA7xx EVM Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* arm: omap: reset sata on bootDmitry Lifshitz2015-01-05-0/+9
| | | | | | | | | | | | | On OMAP platforms (like OMAP5) Linux kernel fails to detect a SATA device if it is used by U-Boot. It happens because U-Boot does not reset SATA controller before boot. Reset the controller on OS boot so that Linux will have a clean state to work with. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* OMAP5+: sata/scsi: implement scsi_bus_reset()Dmitry Lifshitz2015-01-05-0/+6
| | | | | | | | Implement missing scsi_bus_reset() for SCSI subsystem commands on OMAP platforms. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* omap-common/hwinit-common.c: timer_init() doesn't need to touch gdTom Rini2015-01-05-5/+0
| | | | | | | | | | The gd will be cleared at first so we don't need to set arch.tbl to 0. In addition, the checks later against lastinc also work fine with an initial value of 0 here. This also brings us in line with sunxi code for example. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* arm: am33xx: Handle NAND+I2C boot-device the same way as NANDStefan Roese2014-12-04-2/+13
| | | | | | | | | | | | | | Re-map NAND&I2C boot-device to the "normal" NAND boot-device. Otherwise the SPL boot IF can't handle this device correctly. Somehow booting with Hynix 4GBit NAND H27U4G8 on Siemens Draco leads to this boot-device passed to SPL from the BootROM. With this change, Draco boots just fine into main U-Boot. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Roger Meier <r.meier@siemens.com> Cc: Samuel Egli <samuel.egli@siemens.com>
* arm: omap: add support for am57xx devicesFelipe Balbi2014-12-04-1/+1
| | | | | | | | just add a few ifdefs around because this device is very similar to dra7xxx. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: omap-common: emif: allow to map memory without interleavingFelipe Balbi2014-12-04-4/+5
| | | | | | | | | If we want to have two sections, one on each EMIF, without interleaving, current code wouldn't enable emif2. Fix that problem. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-24-0/+5
|\
| * sata: implement reset_sata for dwc_ahsataNikita Kiryanov2014-11-24-0/+5
| | | | | | | | | | | | | | | | | | | | | | Add reset_sata() to the sata driver interface and implement it for dwc_ahsata. This function cleans up after sata_init(), and therefore accepts a device number like sata_init() does. A dummy implementation is provided for the rest of the drivers. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de>
* | replace DIV_ROUND with DIV_ROUND_CLOSESTMasahiro Yamada2014-11-20-3/+3
|/ | | | | | | | | | | | | The Linux-compatible macro DIV_ROUND_CLOSEST is a bit more flexible and safer than DIV_ROUND. For example, foo = DIV_ROUND_CLOSEST(x, y++) works expectedly, but foo = DIV_ROUND(x, y++) does not. (y is incremented twice.) Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Rename some defines containing FAT in their name to be filesystem genericGuillaume GARDET2014-10-27-2/+2
| | | | | | | | | | | Rename some defines containing FAT in their name to be filesystem generic: MMCSD_MODE_FAT => MMCSD_MODE_FS CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP5+: sata: Move scsi_scan() to the right placeRoger Quadros2014-10-10-1/+1
| | | | | | | scsi_scan() must be called as part of scsi_init() and not as part of sata_init(). Signed-off-by: Roger Quadros <rogerq@ti.com>
* OMAP5+: sata/scsi: Implement scsi_init()Roger Quadros2014-10-10-0/+6
| | | | | | | | | | On OMAP platforms, SATA controller provides the SCSI subsystem so implement scsi_init(). Get rid of the unnecessary sata_init() call from dra7xx-evm and omap5-uevm board files. Signed-off-by: Roger Quadros <rogerq@ti.com>
* arm: Add missing .vectors section to linker scriptsBenoît Thébaudeau2014-08-30-0/+1
| | | | | | | | | | Commit 41623c9 'arm: move exception handling out of start.S files' missed some linker scripts. Hence, some boards no longer had exception handling linked since this commit. Restore the original behavior by adding the .vectors section to these linker scripts. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* ARM: DRA: Enable VTT regulatorLokesh Vutla2014-08-25-0/+3
| | | | | | | | | | DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA7: Enable software leveling for dra7Sricharan R2014-08-25-37/+1
| | | | | | | | | | Currently hw leveling is enabled by default on DRA7/72. But the hardware team suggested to use sw leveling as hw leveling is not characterized and seen some test case failures. So enabling sw leveling on all DRA7 platforms. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: omap: clean redundant PISMO_xx macros used in OMAP3pekon gupta2014-07-25-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PISMO_xx macros were used to define 'Platform Independent Storage MOdule' related GPMC configurations. This patch - Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided by current u-boot infrastructure. - Removes unused redundant macros, which are no longer required after merging of common platform code in following commit commit a0a37183bd75e74608bc78c8d0e2a34454f95a91 ARM: omap: merge GPMC initialization code for all platform +-----------------+-----------------------------------------------------------+ | Macro | Reason for removal | +-----------------+-----------------------------------------------------------+ | PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so | | | configuring GPMC chip-select for smallest allowable | | | segment (GPMC_SIZE_16M) is enough. | +-----------------+-----------------------------------------------------------+ | PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of | | | 128MB (GPMC_SIZE_128M) | +-----------------+-----------------------------------------------------------+ +-----------------+-----------------------------------------------------------+ | PISMO1_NOR | Unused Macros | | PISMO1_NAND | | | PISMO2_CS0 | | | PISMO2_CS1 | | | PISMO1_ONENAND | | | PISMO2_NAND_CS0 | | | PISMO2_NAND_CS1 | | | PISMO1_NOR_BASE | | | PISMO1_NAND_BASE| | | PISMO2_CS0_BASE | | +-----------------+-----------------------------------------------------------+ Signed-off-by: Pekon Gupta <pekon@ti.com>
* ARM: omap: fix GPMC address-map size for NAND and NOR devicespekon gupta2014-07-25-2/+7
| | | | | | | | | | | | | | | | | | | | | | Fixes commit a0a37183bd75e74608bc78c8d0e2a34454f95a91 ARM: omap: merge GPMC initialization code for all platform 1) NAND device are not directly memory-mapped to CPU address-space, they are indirectly accessed via following GPMC registers: - GPMC_NAND_COMMAND_x - GPMC_NAND_ADDRESS_x - GPMC_NAND_DATA_x Therefore from CPU's point of view, NAND address-map can be limited to just above register addresses. But GPMC chip-select address-map can be configured in granularity of 16MB only. So this patch uses GPMC_SIZE_16M for all NAND devices. 2) NOR device are directly memory-mapped to CPU address-space, so its address-map size depends on actual addressable region in NOR FLASH device. So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map size configuration. Signed-off-by: Pekon Gupta <pekon@ti.com>
* ARM: OMAP: Fix handling of errata i727Rajendra Nayak2014-07-25-1/+2
| | | | | | | | | | | | The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5 ES 1.0 devices. The current revision check erroneously implements this on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance) infact causes an asynchronous abort and ends up masking it in CPSR, only to be uncovered once the kernel switches to userspace. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: omap: Fix GPMC init for OMAP3 platformsStefan Roese2014-07-25-1/+1
| | | | | | | | | | | | | | | | | | | Commit a0a37183 (ARM: omap: merge GPMC initialization code for all platform) broke NAND on OMAP3 based platforms. I noticed this while testing the latest 2014.07-rc version on the TAO3530 board. NAND detection did not work with this error message: NAND: nand: error: Unable to find NAND settings in GPMC Configuration - quitting As OMAP3 configs don't set CONFIG_NAND but CONFIG_NAND_CMD. the GPMC was not initialized for NAND at all. This patch now fixes this issue. Tested on TAO3530 board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pekon Gupta <pekon@ti.com> Cc: Tom Rini <trini@ti.com> Acked-by: Pekon Gupta <pekon@ti.com>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-07-01-2/+4
|\
| * OMAP: disable gpmc timeout safely for reenablingStefano Babic2014-06-19-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gpmc timeout is disabled and the reset counter is set to 0. However, if later a driver activates the timeout setting the reset to a valid value, the old reset value with zero is still valid for the first access. In fact, the timeout block loads the reset counter after a successful access. Found on a am335x board with a FPGA connected to the GPMC bus together with the NAND. When the FPGA driver in kernel activates the timeout, the system hangs at the first access by the NAND driver. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * omap: Don't enable GPMC CS0 with nothing attachedAsh Charles2014-06-19-1/+2
| | | | | | | | | | | | | | | | | | | | | | If CONFIG_(NAND|NOR|ONENAND) is not defined, no configuration is set for GPMC on chip select #0---size is 0. In this case, the GPMC configuration should be reset but not enabled. Enabling causes the Gumstix DuoVero board to hang when entering Linux. Signed-off-by: Ash Charles <ashcharles@gmail.com> [trini: Switch to testing base as GPMC_SIZE_256M is 0x0] Signed-off-by: Tom Rini <trini@ti.com>
* | am33xx/omap: Allow cache enable for all Sitara/OMAPSimon Glass2014-06-11-42/+60
|/ | | | | | | | | Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined. This speeds up the Beaglebone Black boot considerable. (Tested only on Beaglebone Black with SD card boot) Signed-off-by: Simon Glass <sjg@chromium.org>
* ARM: OMAP: Fix omap_sdram_size calculationLokesh Vutla2014-05-23-4/+7
| | | | | | | | | Last section of DMM is used for trapping tiler unmapped sections. Corresponding trap_size should be deducted from total SDRAM size only if trap section is overlapping with available SDRAM based on DMM sections. Fixing the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>