summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/mx6/ddr.c
Commit message (Collapse)AuthorAgeLines
* ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routinesEric Nelson2016-11-29-2/+1
| | | | | | | | | | | | | | | The DDR calibration routines are gated by conditionals for the i.MX6DQ SOCs, but with the use of the sysinfo parameter, these are usable on at least i.MX6SDL and i.MX6SL variants with DDR3. Also, since only the Novena board currently uses the dynamic DDR calibration routines, these routines waste space on other boards using SPL. Add a KConfig entry to allow boards to selectively include the DDR calibration routines. Signed-off-by: Eric Nelson <eric@nelint.com>
* mx6: ddr: add routine to return DDR calibration dataEric Nelson2016-11-29-0/+23
| | | | | | | | | | | | Add routine mmdc_read_calibration() to return the output of DDR calibration. This can be used for debugging or to aid in construction of static memory configuration. This routine will be used in a subsequent patch set adding a virtual "mx6memcal" board, but could also be useful when gathering statistics during an initial production run. Signed-off-by: Eric Nelson <eric@nelint.com>
* mx6: ddr: pass mx6_ddr_sysinfo to calibration routinesEric Nelson2016-11-29-42/+56
| | | | | | | | | | | | | | | | | | | | | The DDR calibration routines have scattered support for bus widths other than 64-bits: -- The mmdc_do_write_level_calibration() routine assumes the presence of PHY1, and -- The mmdc_do_dqs_calibration() routine tries to determine whether one or two DDR PHYs are active by reading MDCTL. Since a caller of these routines must have a valid struct mx6_ddr_sysinfo for use in calling mx6_dram_cfg(), and the bus width is available in the "dsize" field, use this structure to inform the calibration routines which PHYs are active. This allows the use of the DDR calibration routines on CPU variants like i.MX6SL that only have a single MMDC port. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Marek Vasut <marex@denx.de>
* mx6: ddr: allow 32 cycles for DQS gating calibrationEric Nelson2016-11-29-0/+7
| | | | | | | | | | | The DDR calibration code is only setting flag DG_CMP_CYC (DQS gating sample cycle) for the first PHY. Set the 32-cycle flag for both PHYs and clear when done so the MPDGCTRL0 output value isn't polluted with calibration artifacts. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Marek Vasut <marex@denx.de>
* mx6: ddr: Allow changing REFSEL and REFR fieldsFabio Estevam2016-09-06-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently MX6 SPL DDR initialization hardcodes the REF_SEL and REFR fields of the MDREF register as 1 and 7, respectively for DDR3 and 0 and 3 for LPDDR2. Looking at the MDREF initialization done via DCD we see that boards do need to initialize these fields differently: $ git grep 0x021b0020 board/ board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */ board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800 board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800 board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800 So introduce a mechanism for users to be able to configure REFSEL and REFR fields as needed. Keep all the mx6 SPL users in their current REF_SEL and REFR values, so no functional changes for the existing users. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
* imx: mx6: ddr: support i.MX6D/QPlusPeng Fan2016-05-24-2/+2
| | | | | | | Support i.MX6D/QPlus. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6: use simpler runtime cpu dection macrosPeng Fan2016-05-24-6/+4
| | | | | | | | Use simpler runtime cpu dection macros. i.MX6DL and i.MX6SOLO work the same, so use is_mx6sdl. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* arm: imx6: Switch DDR3 calibration to wait_for_bit()Marek Vasut2016-03-25-32/+12
| | | | | | | | | Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit() to generic implementation of wait_for_bit(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
* arm: imx6: Add DDR3 calibration code for MX6 Q/D/DLMarek Vasut2016-02-02-0/+559
| | | | | | | | | Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code fine-tunes the behavior of the MMDC controller in order to improve the signal integrity and memory stability. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* imx: ddr: drop duplicated debug infoPeng Fan2016-01-03-1/+0
| | | | | | | Drop duplicated debug info for tcl. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* Revert "imx: mx6: ddr correct tRFC and tXS"Peng Fan2015-09-13-2/+2
| | | | | | | | | | | | This reverts commit 059323fb6a8f21637bb617919715c2427f24777c. This commit 059323fb6a8f21637bb617919715c2427f24777c use JESD79-3E which is not the newest spec. Should use JESD79-3F in which tRFC is 260ns for 4Gb chip. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com>
* imx: mx6: ddr: add LPDDR2 supportPeng Fan2015-09-02-4/+296
| | | | | | | | | | | | | | Add LPDDR2 support: 1. Implement a function mx6_lpddr2_cfg to initialize MMDC for LPDDR2. 2. Introduce a structure mx6_lpddr2_cfg, most entrys are same to mx6_ddr3_cfg, but still keep it a single one for easy to choose parameters for LPDDR2. 3. If ddr_type is LPDDR2, use mx6_lpddr2_cfg to init MMDC. 4. Update comments. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com>
* imx: mx6: ddr init MMDC according to ddr_typePeng Fan2015-09-02-1/+13
| | | | | | | | | | | | | | | | | To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper. The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg when ddr_type is for DDR3. Later we can use ddr_type to initialize MMDC for LPDDR2. Initialize ddr_type for different boards which enable SPL. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Stefan Roese <sr@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Stefan Roese <sr@denx.de>
* imx: mx6: ddr add dram io configuration and header file for i.MX6SLPeng Fan2015-09-02-0/+55
| | | | | | | | | Define two structure mx6sl_iomux_ddr_regs and mx6sl_iomux_grp_regs. Add a new function mx6sl_dram_iocfg to configure dram io. Add header file to define macros for register address. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6: ddr correct tRFC and tXSPeng Fan2015-09-02-2/+2
| | | | | | | | | | | To Chip density 4Gb, tRFC should be 300ns, see "Table 61 — Refresh parameters by device density" of JESD79-3E. tXS(min) is max(5nCK, tRFC(min) + 10ns). Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
* imx: mx6: ddr no support MMDC1 for i.MX6SLPeng Fan2015-09-02-2/+4
| | | | | | | | | i.MX 6SoloLite only supports MMDC0, so do not access MMDC1 for i.MX 6SL. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
* imx:mx6ul add dram spl configuration and header filePeng Fan2015-08-02-10/+51
| | | | | | | | | | | | 1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs. 2. Add a new function mx6ul_dram_iocfg to configure dram io. 3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support runtime check, but not hardcoding #ifdef macros. 4. Introduce mx6ul-ddr.h, which includes the register address for DRAM IO configuration. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* arm: mx6: ddr: set fast-exit on DDR3 if pd_fast_exit specifiedTim Harvey2015-05-19-1/+2
| | | | | | | | | | | | | Commit fa8b7d66f49f0c7bd41467fe78f6488d8af6976a introduced fast-exit support to the MMDC however enabling it on the DDR3 got missed. Make sure we enable it on the DDR3 as well. Gateworks uses Micron memory as well as Winbond in MX6. We have found in testing that we need to enable fast-exit for Winbond stability. Gateworks boards are currently the only boards using the MX6 SPL and enabling fast-exit mode. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* arm: mx6: ddr3: Remove dead codeNikolay Dimitrov2015-05-15-22/+0
| | | | | | | imx6 mmdc supports data rates up to 1066 MT/s, so remove the code handling higher data rates. Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
* arm: mx6: Clamp MMDC and DDR3 clocks for timing calculationsNikolay Dimitrov2015-05-15-7/+23
| | | | | | | | | | | | | | | | This is proposal for clamping the MMDC/DDR3 clocks to the maximum supported frequencies as per imx6 SOC models, and for dynamically calculating valid clock value based on mem_speed. Currently the code uses impossible values for mem_speed (1333, 1600 MT/s) for calculating the DDR timings, and uses fixed clock (528 or 400 MHz) which doesn't take into account DDR3 memory limitations. Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg> Cc: Fabio Estevam <festevam@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com>
* arm: mx6: ddr: add pd_fast_exit flag to system informationTim Harvey2015-04-22-1/+6
| | | | | | | | | | | DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit. In slow-exit mode the DLL is off but in some quiescent state that makes it easy to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK). In fast-exist mode the DLL is maintained such that it is ready again in about 3tCK. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx:mx6sx add dram io configure for mx6sxPeng Fan2015-01-22-14/+82
| | | | | | | | | | | Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs. Add a new function mx6sx_dram_iocfg to configure dram io. Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1 to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1 effects as "mmdc1->entry=value". Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* cosmetic: replace MIN, MAX with min, maxMasahiro Yamada2014-09-24-20/+20
| | | | | | | The macro MIN, MAX is defined as the aliase of min, max, respectively. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arm: mx6: ddr: fix cs0_end calculationNikita Kiryanov2014-09-09-3/+1
| | | | | | | | | | | | | | | | Current way of calculation CS0_END field for MMDCx_MDASP register is problematic because in most cases the user is forced to define cs_density in an unnatural way: as value - 2, instead of value. This breaks the abstraction provided by struct mx6_ddr_sysinfo because the user is forced to be aware of the way the calculation is performed. Refactor the calculation. Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* arm: mx6: ddr: configure MMDC for slow_pdNikita Kiryanov2014-09-09-0/+1
| | | | | | | | | | | | | | | | According to MX6 TRM, both MMDC and DRAM should be configured to the same powerdown precharge. Currently, mx6_dram_cfg() configures MMDC for fast pd (MDPDC[7] = 0), and the DRAM for 'slow exit (DLL off)' (MR0[12] = 0). Configure MMDC for slow pd. Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Tim Harvey <tharvey@gateworks.com>
* arm: mx6: ddr: do not write into reserved bitNikita Kiryanov2014-09-09-1/+1
| | | | | | | | | Bit 16 in mapsr register is in a reserved field. Don't write to it. Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Acked-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* arm: mx6: ddr: cleanupNikita Kiryanov2014-09-09-141/+137
| | | | | | | | | No functional changes. Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Acked-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* ARM: mx6: Handle the MMDCx_MDCTL COL field capricesMarek Vasut2014-08-20-1/+7
| | | | | | | | | The COL field value cannot be easily calculated from the desired column number. Instead, there are special cases for that, see the datasheet, MMDCx_MDCTL field description, field COL . Cater for those special cases. Signed-off-by: Marek Vasut <marex@denx.de>
* mx6: add mmdc configuration for MX6Q/MX6DLTim Harvey2014-06-06-0/+490
- add function for configuring iomux based on board-specific regs - add function for configuring mmdc based on board-specific and chip-specific data Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
generated by cgit v1.1 at 2024-07-07 12:06:38 +0000