summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/am33xx
Commit message (Collapse)AuthorAgeLines
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-08-0/+326
|\ | | | | | | | | This required manual merging drivers/mtd/nand/Makefile and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
| * am33xx: add ELM supportMansoor Ahamed2012-12-10-0/+218
| | | | | | | | | | | | | | | | | | AM33XX has Error Location Module (ELM) that can be used in conjuction with GPMC controller to implement BCH codes fully in hardware. This code is mostly taken from arago tree. Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com> Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
| * am33xx: NAND supportIlya Yanok2012-12-10-0/+108
| | | | | | | | | | | | | | | | TI AM33XX has the same GPMC controller as OMAP3 so we could just use the existing omap_gpmc driver. This patch adds adds required definitions/intialization. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* | am33xx: init OTG hardware and new musb gadget driverIlya Yanok2012-11-20-0/+93
|/ | | | | | | | AM33xx has support for dual port MUSB OTG controller. This patch adds initialization for the controller using new MUSB gadget driver and ether gadget. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* am33xx: Enable UART{1,2,3,4,5} clocksAndrew Bradford2012-10-25-0/+35
| | | | | | | | If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232 cape or the am335x_evm daughterboard, enable the required clocks for the UART in use. Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
* am33xx: support board specific ddr settingsPeter Korsgaard2012-10-25-103/+11
| | | | | | | | | Move the hardcoded ddr2/ddr3 settings for the ti boards to board code, so other boards can use different types/timings. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make apply with rtc32k_enable() in the file] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: move generic parts of pinmux handling out from board/ti/am335xPeter Korsgaard2012-10-25-0/+34
| | | | | | So they are available for other boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
* am33xx/board: use cpu_mmc_init() for default mmc initializationPeter Korsgaard2012-10-25-2/+2
| | | | | | So platforms can override it with board_mmc_init() if needed. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
* am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard2012-10-25-261/+0
| | | | | | | | | The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx/board.c: make wdtimer/uart_base staticPeter Korsgaard2012-10-25-2/+4
| | | | | | Only used here (and uart_base only for SPL). Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
* am33xx: Add SPI SPL as an optionTom Rini2012-10-25-0/+1
| | | | | | | Add the required config.mk logic for this SoC as well as the BOOT_DEVICE define. Finally, enable the options on the am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
* am335x: Enable RTC 32K OSC clockVaibhav Hiremath2012-10-25-1/+26
| | | | | | | | | | | | | | | | | In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Enable DDR3 for DDR3 version of beagleboneJoel A Fernandes2012-10-23-2/+7
| | | | | | | | | DDR3 support is tested and working with beaglebone hardware. Include a check for this board type and configure DDR3. The timings and other configuration match EVM SK. Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Acked-by: Jason Kridner <jdk@ti.com>
* SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linuxTom Rini2012-09-27-0/+2
| | | | | | | | | | | | | | In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer, clear the BSS and call board_init_r. We mark this as weak as some platforms may need to perform additional initalization at this point. We provide a gd that we know will be in a usable location, once the BSS has been cleared to help with this as well. Finally, we no longer call relocate_code so remove that from the armv7 version. Next, both board_init_f and jump_to_image_linux are going to be inherently arch-specific, so move these versions to arch/arm/lib/spl.c Signed-off-by: Tom Rini <trini@ti.com>
* SPL: Move the omap SPL framework to common/splTom Rini2012-09-27-1/+1
| | | | | | | | | | | | | Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL framework, enable on all of the previously using boards. We move the spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave the NAND one in-place as we plan to replace it later in this series. We use common/spl to avoid linker problems with respect to merging constant strings in objects. Otherwise all strings in common/ will be linked in and kept which grows SPL in size too much. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>Tom Rini2012-09-27-1/+1
| | | | | | | Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Remove redundant timer configTom Rini2012-09-04-20/+0
| | | | | | | | | | We have the timer code in arch/arm/cpu/armv7/omap-common/timer.c that has been configuring and enabling the timer, so remove our code that does the same thing by different methods. Tested on EVM GP, SK-EVM and Beaglebone. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx evm: Update secure_emif_sdram_config during ddr initSatyanarayana, Sandhya2012-09-01-1/+4
| | | | | | | | | | | | | | | This patch updates secure_emif_sdram_config with the same value written to sdram_config during ddr3 initialization. During suspend/resume, this value is copied into sdram_config. With this, a write to sdram_config at the end of resume sequence which triggers an init sequence can be avoided. Without this register write in place, the DDR_RESET line goes low for a few cycles during resume which is a violation of the JEDEC spec. Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
* am33xx: Add support, update omap3 McSPI driverTom Rini2012-09-01-0/+5
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Correct MMC1, remove MMC2 supportTom Rini2012-09-01-1/+7
| | | | | | | | - Correct the MMC1 base offset - Remove MMC2 (that area is reserved and not MMC2). - Add the real BOOT_DEVICE_MMC2 value Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Rework pinmux functionsTom Rini2012-09-01-27/+5
| | | | | | | | | | - Move definition of the EEPROM contents to <asm/arch/sys_proto.h> - Make some defines a little less generic now. - Pinmux must be done by done by SPL now. - Create 3 pinmux functions, uart0, i2c0 and board. - Add pinmux specific to Starter Kit EVM for MMC now. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx evm: Add CONFIG_CMD_EEPROM and relatedTom Rini2012-09-01-9/+4
| | | | | | | am33xx boards have at least one eeprom and in the case of beaglebones with capes, more. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Add support for TI AM335x StarterKit EVMTom Rini2012-09-01-2/+39
| | | | | | | | | | - Board requires gpio0 #7 to be set to power DDR3. - Board uses DDR3, add a way to determine which DDR type to call config_ddr with. - Both of the above require filling in the header structure early, move it into the data section. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Remove board/ti/am335x/evm.cTom Rini2012-09-01-0/+173
| | | | | | | | | The intention has always been (and boards are to support) an i2c EEPROM that will identify what hardware they are, allowing a single binary to support multiple boards. As such, remove the 'evm.c' file as there is nothing EVM centric in it currently, only SoC peripheral configuration. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Add DDR3 (Micron MT41J128M16JT-125) timings and supportTom Rini2012-09-01-0/+43
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Rework config_ddr to make DDR3 support easier.Tom Rini2012-09-01-14/+23
| | | | | | | | In order to support DDR3 as well as DDR2, we need to perform the same init sequence, but with different values. So change config_ddr() to toggle setting pointers/etc for what DDR2 wants, and then calling. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Move some variables in emif4.c, mark them static.Tom Rini2012-09-01-4/+3
| | | | | | We need vtpreg and ddrctrl but no longer need a second ddrregs. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Correct and clean up ddr_regs structTom Rini2012-09-01-15/+2
| | | | | | | | | | | | | | The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry. Correct this by documenting a missing register that will be used at some point in the future (when write leveling is supported). Further, the cmdNcs{force,delay} fields are undocumented and we have been setting them to zero, remove. Next, setting of the 'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the ddr_data entries, so program it there. Finally, comment on how we are configuring the DATA1 registers that correspond to the DATA0 (dt0) registers defined in the struct. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Do not touch 'ratio1' fieldsTom Rini2012-09-01-17/+0
| | | | | | | | | The various ratio1 fields are not documented in any of the documentation I can find. Removing these and testing has yielded success, so remove the code that sets them and move their locations into the reserved fields. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Rework config_io_ctrl slightlyTom Rini2012-09-01-15/+7
| | | | | | | | | This function sets a number of related registers to the same value (the registers in question all have the same field descriptions and are related in operation). Rather than defining a struct and setting the value repeatedly, just pass in the value. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Use emif_regs struct for storing initialization valuesTom Rini2012-09-01-44/+27
| | | | | | | Rather than defining our own structs to note what to use when programming the EMIF and related re-use the emif_regs struct. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Turn a number of 'int' functions to 'void'Tom Rini2012-09-01-36/+9
| | | | | | | | A number of memory initalization functions were int and always returned 0. Further it's not feasible to be doing error checking here, so simply turn them into void functions. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Document what we're doing with ddrctrl->ddrckectrlTom Rini2012-09-01-4/+2
| | | | | | | | | - Remove the call to set ddrctrl->ddrioctrl as it's all zeros. - Comment what we're really setting in ddrctrl->ddrckectrl which is that we're operating in the normal mode where EMIF/PHY clock is controlled by the PHY. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Clean up unused DDR defines, prefix more with 'DDR2'Tom Rini2012-09-01-23/+23
| | | | | | | - Remove a handful of unused defines. - Prefix more values with 'DDR2' as DDR3 will require different values. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Move the call to ddr_pll_config, make it take the frequencyTom Rini2012-09-01-3/+4
| | | | | | | | Depending on if we have DDR2 or DDR3 on the board we will need to call ddr_pll_config with a different value. This call can be delayed slightly to the point where we know which type of memory we have. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Pass to config_ddr the type of memory that is connectedTom Rini2012-09-01-18/+23
| | | | | | | | | We need to pass in the type of memory that is connected to the board. The only reliable way to do this is to know what type of board we are running on (which later will be knowable in s_init()). For now, pass in the value of DDR2. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Make config_cmd_ctrl / config_ddr_data take const structsTom Rini2012-09-01-59/+46
| | | | | | | | | Rework the EMIF4/DDR code slightly to setup the structs that config_cmd_ctrl and config_ddr_data take to be setup at compile time and mark them as const. This lets us simplify the calling path slightly as well as making it easier to deal with DDR3. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Rework DDR2 EMIF initalization slightlyTom Rini2012-09-01-15/+2
| | | | | | | With the previous bugfix we now don't need to set two different REF_CTRL values and instead set the final value. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Bugfix to config_sdram()Tom Rini2012-09-01-2/+1
| | | | | | | When we change SDRAM_CONFIG this triggers a refresh based on all of the parameters that we have programmed so we must do this last. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Remove extra check in enable_ddr_clocksTom Rini2012-09-01-5/+0
| | | | | | | We do not need to check for EMIF_GCLK and L3_GCLK being active. This was a hold-over from bringup and no longer required. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Convert to using <asm/emif.h> to describe the EMIFTom Rini2012-09-01-14/+15
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Enable gpio0 clockTom Rini2012-09-01-0/+4
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: CPSW init and definitionsChandan Nath2012-09-01-1/+7
| | | | | | | | | This patch adds platform-specific initialization for CPSW switch on TI AM33XX SoCs. Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split init out of original patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* omap: am335x_evm: enable i2c1 channelSteve Sakoman2012-09-01-0/+5
| | | | | | | This patch sets up pinmux, enables fclk, and defines CONFIG_I2C_MULTI_BUS Signed-off-by: Steve Sakoman <steve@sakoman.com>
* omap: am33xx: enable gpio supportSteve Sakoman2012-09-01-0/+25
| | | | | | | | | | | This patch uses the code in omap-common to support gpio modules 1-3 on am33xx based boards. It adds base address and register definitions, enables clocks to the modules, and enables building the common gpio code for CONFIG_AM33XX as well as CONFIG_OMAP Signed-off-by: Steve Sakoman <steve@sakoman.com>
* am33xx: Do not call init_timer twiceTom Rini2012-07-07-14/+16
| | | | | | | We do not need to call init_timer both in SPL and U-Boot itself, just SPL needs to initialize the timer. Signed-off-by: Tom Rini <trini@ti.com>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-15-1/+1
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* ARM: AM33XX: Add i2c supportPatil, Rachna2012-01-23-0/+5
| | | | | | | Add i2c driver board hookup for AM335X EVM Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
* ARM:AM33XX: Add SPL support for AM335X EVMChandan Nath2012-01-16-79/+66
| | | | | | | | | | | This patch is added to support SPL feature on AM335X platform. In this patch, MMC1 is configured as boot device for SPL and support for other devices will be added in the next patch series. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM:AM33XX: Add mmc/sd supportChandan Nath2012-01-16-0/+12
| | | | | | | | | This patch add supports for mmc/sd driver on AM335X platform. PLL and pinmux configurations for mmc/sd are configured in this patch. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
generated by cgit v1.1 at 2024-11-06 17:36:12 +0000