summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/am33xx/board.c
Commit message (Collapse)AuthorAgeLines
* am33xx: Enable D-CACHE on !CONFIG_SYS_DCACHE_OFFTom Rini2013-12-12-0/+8
| | | | | | | Test on Beaglebone white over cpsw, usb ether and SD card (read and write), performance increased, crc32 of data matches. Signed-off-by: Tom Rini <trini@ti.com>
* arm, am33x: make RTC32K OSC enable configurableHeiko Schocher2013-11-11-0/+4
| | | | | | | | | | | | | | As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
* am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini2013-11-01-3/+4
| | | | | | | Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
* am335x:Handle worst case scenario for Errata 1.0.24Steve Kipisz2013-09-20-0/+2
| | | | | | | | | | | | | In Errata 1.0.24, if the board is running at OPP50 and has a warm reset, the boot ROM sets the frequencies for OPP100. This patch attempts to drop the frequencies back to OPP50 as soon as possible in the SPL. Then later the voltages and frequencies up set higher. Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Adapt to current framework] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Add am33xx_spl_board_init function, callTom Rini2013-09-20-0/+9
| | | | | | | | We need to allow for a further call-out in spl_board_init. Call this am33xx_spl_board_init and add a __weak version. This function may be used to scale the MPU frequency up, depending on board needs. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: AM33xx: Move s_init to a common placeHeiko Schocher2013-08-15-6/+56
| | | | | | | | | | | | s_init has the same outline for all the AM33xx based board. So making it generic. This also helps in addition of new Soc with minimal changes. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* ARM: AM33xx: Cleanup clocks layerLokesh Vutla2013-08-15-6/+0
| | | | | | | | | | | Cleaning up the clocks layer. This helps in addition of new Soc with minimal changes. This is derived from OMAP4 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* am335x_evm: Add support to boot from NOR.Steve Kipisz2013-07-30-1/+1
| | | | | | | | | | | | | | | | | | NOR requires that s_init be within the first 4KiB of the image so that we can perform the rest of the required pinmuxing to talk with the rest of NOR that we are found on. When NOR_BOOT is set we save our environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid using SPL for this case and u-boot.bin is written directly to the start of NOR. We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c with TI81xx checks as at this time U-Boot does not discard unused sections in the main build and this code relies on functions specific to (and only provided in) ti81xx-related code. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-9/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* arm, am33xx: move uart soft reset code to common placeHeiko Schocher2013-06-18-0/+22
| | | | | | | | | | | | | | | move uart soft reset code to common place and call this function from board code, instead of copy and paste this code for every board. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matt Porter <mporter@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Tom Rini <trini@ti.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Tom Rini <trini@ti.com> [trini: Fix igep0033 build, remove 'regval' on pcm051] Signed-off-by: Tom Rini <trini@ti.com>
* arm, am33xx: move rtc32k_enable() to common placeHeiko Schocher2013-06-18-0/+18
| | | | | | | | | | move rtc32k_enable() to common place so all am33xx boards can use it. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matt Porter <mporter@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Tom Rini <trini@ti.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
* am33xx: convert defines from am33xx-specific to generic namesMatt Porter2013-03-24-2/+2
| | | | | | | | Eliminate AM33xx specific names to prepare for TI814x support within AM33xx-land. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* omap_hsmmc: add driver check for write protectionNikita Kiryanov2013-03-08-2/+2
| | | | | | | | Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* omap_hsmmc: implement driver check for card detectionNikita Kiryanov2013-03-08-2/+2
| | | | | | | Implement driver check for card detection. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-08-0/+1
|\ | | | | | | | | This required manual merging drivers/mtd/nand/Makefile and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
| * am33xx: NAND supportIlya Yanok2012-12-10-0/+1
| | | | | | | | | | | | | | | | TI AM33XX has the same GPMC controller as OMAP3 so we could just use the existing omap_gpmc driver. This patch adds adds required definitions/intialization. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* | am33xx: init OTG hardware and new musb gadget driverIlya Yanok2012-11-20-0/+85
|/ | | | | | | | AM33xx has support for dual port MUSB OTG controller. This patch adds initialization for the controller using new MUSB gadget driver and ether gadget. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* am33xx/board: use cpu_mmc_init() for default mmc initializationPeter Korsgaard2012-10-25-2/+2
| | | | | | So platforms can override it with board_mmc_init() if needed. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
* am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard2012-10-25-261/+0
| | | | | | | | | The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx/board.c: make wdtimer/uart_base staticPeter Korsgaard2012-10-25-2/+4
| | | | | | Only used here (and uart_base only for SPL). Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
* am335x: Enable RTC 32K OSC clockVaibhav Hiremath2012-10-25-1/+20
| | | | | | | | | | | | | | | | | In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Enable DDR3 for DDR3 version of beagleboneJoel A Fernandes2012-10-23-2/+7
| | | | | | | | | DDR3 support is tested and working with beaglebone hardware. Include a check for this board type and configure DDR3. The timings and other configuration match EVM SK. Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Acked-by: Jason Kridner <jdk@ti.com>
* SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linuxTom Rini2012-09-27-0/+2
| | | | | | | | | | | | | | In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer, clear the BSS and call board_init_r. We mark this as weak as some platforms may need to perform additional initalization at this point. We provide a gd that we know will be in a usable location, once the BSS has been cleared to help with this as well. Finally, we no longer call relocate_code so remove that from the armv7 version. Next, both board_init_f and jump_to_image_linux are going to be inherently arch-specific, so move these versions to arch/arm/lib/spl.c Signed-off-by: Tom Rini <trini@ti.com>
* SPL: Move the omap SPL framework to common/splTom Rini2012-09-27-1/+1
| | | | | | | | | | | | | Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL framework, enable on all of the previously using boards. We move the spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave the NAND one in-place as we plan to replace it later in this series. We use common/spl to avoid linker problems with respect to merging constant strings in objects. Otherwise all strings in common/ will be linked in and kept which grows SPL in size too much. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>Tom Rini2012-09-27-1/+1
| | | | | | | Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Remove redundant timer configTom Rini2012-09-04-20/+0
| | | | | | | | | | We have the timer code in arch/arm/cpu/armv7/omap-common/timer.c that has been configuring and enabling the timer, so remove our code that does the same thing by different methods. Tested on EVM GP, SK-EVM and Beaglebone. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Correct MMC1, remove MMC2 supportTom Rini2012-09-01-1/+7
| | | | | | | | - Correct the MMC1 base offset - Remove MMC2 (that area is reserved and not MMC2). - Add the real BOOT_DEVICE_MMC2 value Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Rework pinmux functionsTom Rini2012-09-01-27/+5
| | | | | | | | | | - Move definition of the EEPROM contents to <asm/arch/sys_proto.h> - Make some defines a little less generic now. - Pinmux must be done by done by SPL now. - Create 3 pinmux functions, uart0, i2c0 and board. - Add pinmux specific to Starter Kit EVM for MMC now. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx evm: Add CONFIG_CMD_EEPROM and relatedTom Rini2012-09-01-9/+4
| | | | | | | am33xx boards have at least one eeprom and in the case of beaglebones with capes, more. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Add support for TI AM335x StarterKit EVMTom Rini2012-09-01-2/+39
| | | | | | | | | | - Board requires gpio0 #7 to be set to power DDR3. - Board uses DDR3, add a way to determine which DDR type to call config_ddr with. - Both of the above require filling in the header structure early, move it into the data section. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Remove board/ti/am335x/evm.cTom Rini2012-09-01-0/+173
| | | | | | | | | The intention has always been (and boards are to support) an i2c EEPROM that will identify what hardware they are, allowing a single binary to support multiple boards. As such, remove the 'evm.c' file as there is nothing EVM centric in it currently, only SoC peripheral configuration. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Pass to config_ddr the type of memory that is connectedTom Rini2012-09-01-1/+2
| | | | | | | | | We need to pass in the type of memory that is connected to the board. The only reliable way to do this is to know what type of board we are running on (which later will be knowable in s_init()). For now, pass in the value of DDR2. Signed-off-by: Tom Rini <trini@ti.com>
* omap: am33xx: enable gpio supportSteve Sakoman2012-09-01-0/+10
| | | | | | | | | | | This patch uses the code in omap-common to support gpio modules 1-3 on am33xx based boards. It adds base address and register definitions, enables clocks to the modules, and enables building the common gpio code for CONFIG_AM33XX as well as CONFIG_OMAP Signed-off-by: Steve Sakoman <steve@sakoman.com>
* am33xx: Do not call init_timer twiceTom Rini2012-07-07-14/+16
| | | | | | | We do not need to call init_timer both in SPL and U-Boot itself, just SPL needs to initialize the timer. Signed-off-by: Tom Rini <trini@ti.com>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-15-1/+1
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* ARM:AM33XX: Add SPL support for AM335X EVMChandan Nath2012-01-16-4/+47
| | | | | | | | | | | This patch is added to support SPL feature on AM335X platform. In this patch, MMC1 is configured as boot device for SPL and support for other devices will be added in the next patch series. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM:AM33XX: Add mmc/sd supportChandan Nath2012-01-16-0/+7
| | | | | | | | | This patch add supports for mmc/sd driver on AM335X platform. PLL and pinmux configurations for mmc/sd are configured in this patch. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Fix ddr and timer register offsetChandan Nath2012-01-16-4/+4
| | | | | | | | This patch is added to update incorrect ddr and timer register offset. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Add support for TI AM335X EVMChandan Nath2011-10-27-0/+66
This patch adds basic support for booting the board. This patch adds support for the UART necessary to get to the u-boot prompt. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit v1.1 at 2024-08-23 11:23:52 +0000