summaryrefslogtreecommitdiff
path: root/arch/arc
Commit message (Collapse)AuthorAgeLines
* arc: fix separate compilation of start.oAlexey Brodkin2015-04-10-0/+1
| | | | | | | | | | | | | | | While testing "arc: make sure _start is in the beginning of .text section" I haven't done proper clean-up of built binaries and so missed another tiny bit that lead to the following error: --->8--- LD u-boot arc-linux-ld.bfd: cannot find arch/arc/lib/start.o Makefile:1107: recipe for target 'u-boot' failed make: *** [u-boot] Error 1 --->8--- Fix is trivial: put "start.o" in "extra-y". Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: make sure _start is in the beginning of .text sectionAlexey Brodkin2015-04-10-1/+2
| | | | | | | | | | | | | | This is important to have entry point in the beginning of .text section because it allows simple loading and execution of U-Boot. For example pre-bootloader loads U-Boot in memory starting from offset 0x81000000 and then just jumps to the same address. Otherwise pre-bootloader would need to find-out where entry-point is. In its turn if it deals with binary image of U-Boot there's no way for pre-bootloader to get required value. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: add support for SLC (System Level Cache, AKA L2-cache)Alexey Brodkin2015-04-03-0/+65
| | | | | | | | | | | | | | ARCv2 cores may have built-in SLC (System Level Cache, AKA L2-cache). This change adds functions required for controlling SLC: * slc_enable/disable * slc_flush/invalidate For now we just disable SLC to escape DMA coherency issues until either: * SLC flush/invalidate is supported in DMA APIin U-Boot * hardware DMA coherency is implemented (that might be board specific so probably we'll need to have a separate Kconfig option for controlling SLC explicitly) Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* board: Switch Abilis TB-100 board to Driver Model for serial portAlexey Brodkin2015-04-03-0/+25
| | | | | Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org>
* serial-arc: switch to DMAlexey Brodkin2015-04-03-0/+48
| | | | | | | | Now when all infrastructure in ARC is ready for it let's switch ARC UART to driver model. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org>
* arc: minor fixes in KconfigAlexey Brodkin2015-04-03-1/+9
| | | | | | | | | | | | | [1] Fix misspeling in ARC_CACHE_LINE_SHIFT dependency, now cache-line lenth selection is correctly enabled if either I$ or D$ are enabled. [2] Add dummy entry to target list to make sure target type is always mentioned in defconfig. Otherwise defconfig for the first target in the list will not have target name and later on with addition of the new target on top of the list in Kconfig will lead to corrupted configuration expanded from defconfig. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: get rid of CONFIG_SYS_GENERIC_GLOBAL_DATAAlexey Brodkin2015-04-03-1/+8
| | | | | | | | | | As discussed on mailing list we're drifting away from CONFIG_SYS_GENERIC_GLOBAL_DATA in favour to use of board_init_f_mem() for global data. So do this for ARC architecture. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: clean-up init procedureAlexey Brodkin2015-04-03-77/+94
| | | | | | | | | | | | | | | | Intention behind this work was elimination of as much assembly-written code as it is possible. In case of ARC we already have relocation fix-up implemented in C so why don't we use C for U-Boot copying, .bss zeroing etc. It turned out x86 uses pretty similar approach so we re-used parts of code in "board_f.c" initially implemented for x86. Now assembly usage during init is limited to stack- and frame-pointer setup before and after relocation. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Simon Glass <sjg@chromium.org>
* arc: move low-level interrupt and exception handlers in a separate fileAlexey Brodkin2015-04-03-144/+152
| | | | | | | | This separation makes maintenance of code easier because those low-level interrupt- or exception handling routines are pretty static and usually require not much care while start-up code is a subject of modifications and enhancements. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: merge common start-up code between ARC and ARCv2Alexey Brodkin2015-04-03-294/+82
| | | | | | | | | | Even though ARCompact and ARCv2 are not binary compatible most of assembly instructions are used in both. With this change we'll get rid of duplicate code. Still IVTs are implemented differently so we're keeping them in separate files. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: cache - build invalidate_icache_all() and invalidate_dcache_all()Alexey Brodkin2015-04-03-4/+8
| | | | | | | | | | | | | | | | | always Make both invalidate_icache_all() and invalidate_dcache_all() available even if U-Boot is configured with CONFIG_SYS_DCACHE_OFF and/or CONFIG_SYS_ICACHE_OFF. This is useful because configuration of U-Boot may not match actual hardware features. Real board may have cache(s) but for some reason we may want to run U-Boot with cache(s) disabled (for example if some peripherals work improperly with existing drivers if data cache is enabled). So board may start with cache(s) enabled (that's the case for ARC cores with built-in caches) but early in U-Boot we disable cache(s) and make sure all contents of data cache gets flushed in RAM. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* generic-board: select SYS_GENERIC_BOARD for some architecturesMasahiro Yamada2015-03-28-1/+0
| | | | | | | | | | | | We have done with the generic board conversion for all the boards of ARC, Blackfin, M68000, MicroBlaze, MIPS, NIOS2, Sandbox, X86. Let's select SYS_GENERIC_BOARD for those architectures, so we can tell which architecture has finished the conversion at a glance. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
* generic-board: move __HAVE_ARCH_GENERIC_BOARD to KconfigMasahiro Yamada2015-03-28-3/+0
| | | | | | | | Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
* use ASM_NL instead of '; ' for assembler new line character in the macroChen Gang2015-03-05-0/+12
| | | | | | | | | | | | | | | | | For some assemblers, they use another character as newline in a macro (e.g. arc uses '`'), so for generic assembly code, need use ASM_NL (a macro) instead of ';' for it. Basically this is the same patch as applied to Linux kernel - http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/include/linux/linkage.h?id=9df62f054406992ce41ec4558fca6a0fa56fffeb but modified a bit to fit in U-Boot. Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com>
* arc: introduce U-Boot port for ARCv2 ISAAlexey Brodkin2015-02-13-3/+335
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ARC HS and ARC EM are new cores based on ARCv2 ISA which is binary incompatible with ISAv1 (AKA ARCompact). Significant difference between ISAv2 and v1 is implementation of interrupt vector table. In v1 it is implemented in the same way as on many other architectures - as a special location where user may put whether code executed in place (if machine word of space is enough) or jump to a full-scale interrupt handler. In v2 interrupt table is just an array of adresses of real interrupt handlers. That requires a separate section for IVT that is not encoded as code by assembler. This change adds support for following cores: * ARC EM6 (simple 32-bit microcontroller without MMU) * ARC HS36 (advanced 32-bit microcontroller without MMU) * ARC HS38 (advanced 32-bit microcontroller with MMU) As a part of ARC HS38 new version of MMU (v4) was introduced. Also this change adds AXS131 board which is the same DW ARC SDP base board but with ARC HS38 CPU tile. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: build libgcc in U-BootAlexey Brodkin2015-02-09-0/+527
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This way we may have very limited set of functions implemented so we save some space. Also it allows us to build U-Boot for any ARC core with the same one toolchain because we don't rely on pre-built libgcc. For example: * we may use little-endian toolchain but build U-Boot for ether endianess * we may use non-multilibbed uClibc toolchain but build U-Boot for whatever ARC CPU flavour that current GCC supports Private libgcc built from generic C implementation contributes only 144 bytes to .text section so we don't see significant degradation of size: --->8--- $ arc-linux-size u-boot.libgcc-prebuilt text data bss dec hex filename 222217 24912 214820 461949 70c7d u-boot.libgcc-prebuilt $ arc-linux-size u-boot.libgcc-private text data bss dec hex filename 222361 24912 214820 462093 70d0d u-boot.libgcc-private --->8--- Also I don't notice visible performance degradation compared to pre-built libgcc (where at least "*div*" functions are had-written in assembly) on typical operations of downloading 10Mb uImage over TFTP and bootm. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: move CPU flags selection to the main "config.mk"Alexey Brodkin2015-02-09-8/+5
| | | | | | | | | As a preparation to ARCv2 port submission we're moving CPU slection flags to a common location. Also it will allow us to have more flexible CPU specification, not only ISA version but CPU family as well checking CONFIG_ARC_CPU_xxx. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: hard-code CONFIG_ARCH_EARLY_INIT_R in asm/config.hAlexey Brodkin2015-02-09-0/+1
| | | | | | | Common arch_early_init_r() is used in "arc/lib/cpu.c" for all ARC boards so there's no sense in separate per-board definitions. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: hard-code CONFIG_SYS_GENERIC_BOARD into asm/config.hAlexey Brodkin2015-02-09-0/+1
| | | | | | | | | There're no other options for ARC except "generic board" so ther's no point to define CONFIG_SYS_GENERIC_BOARD per board. We now have it set fo all ARC boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: add selection of endianess in KconfigAlexey Brodkin2015-02-09-4/+9
| | | | | | | | | | | This change allows to keep board description clean and minimalistic. This is especially helpful if one board may house different CPUs with different features. It is applicable to both FPGA-based boards or those that have CPUs mounted on interchnagable daughter-boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: select cache settings via menuconfigAlexey Brodkin2015-02-09-8/+25
| | | | | | | | | | | This change allows to keep board description clean and minimalistic. This is especially helpful if one board may house different CPUs with different features. It is applicable to both FPGA-based boards or those that have CPUs mounted on interchnagable daughter-boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: define and use PTAG AUX regs for MMUv3 onlyAlexey Brodkin2015-02-09-5/+5
| | | | | | DC_PTAG and IC_PTAG registers only exist in MMUv3. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: add more flavours of ARC700 series CPUAlexey Brodkin2015-02-09-0/+52
| | | | | | | | | | | | | | | | Now we may select a particular version of ARC700: * ARC750D or * ARC770D It allows more flexible (or more fine tuned) configuration of U-Boot. Before that change we relied on minimal configuration but now we may use specific features of each CPU. Moreover allows us to escape manual selection of options that exist in both CPUs but may have say different version like MMUv2 in ARC750D vs MMUv3 in ARC770D. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: memcmp - fix zero-delay loop utilizationIgor Guryanov2015-02-09-0/+2
| | | | | | | | It's prohibited to put branch instruction in the very end of zero-delay loop. On execution this causes "Illegal instruction" exception. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: rename "arc700" in "arcv1"Alexey Brodkin2015-01-15-1/+1
| | | | | | | | | | | | As a preparation to ARCv2 port submission we rename "arc700" folder to "arcv1" which stands for ARCv1 ISA also known as ARCompact. This will allow us to add more flavours of binary-compatible ARCv1 CPUs like ARC600 if needed later on and all required ARCv2 CPUs (which are binary incompatible with ARCv1) in "arcv2" folder in subsequent commits. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* board/synopsys: remove selection of CPU from the boardAlexey Brodkin2015-01-15-0/+3
| | | | | | | | Both ARCangel4 and AXS10x are FPGA-based boards so they may have different CPUs. For now we have only 1 option (ARC700) and we define this as default in arch Kconfig. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: move common sources in libraryAlexey Brodkin2015-01-15-6/+7
| | | | | | | | | | | | | | | | | | | "reset.c" and "cpu.c" have no architecture-specific code at all. Others are applicable to either ARC CPU. This change is a preparation to submission of ARCv2 architecture port. Even though ARCv1 and ARCv2 ISAs are not binary compatible most of built-in modules still have the same programming model - AUX registers are mapped in the same addresses and hold the same data (new featues extend existing ones). So only low-level assembly code (start-up, interrupt handlers) is left as CPU(actually ISA)-specific. This significantyl simplifies maintenance of multiple CPUs/ISAs. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: move linker script in arch/arc/cpu folderAlexey Brodkin2015-01-15-0/+0
| | | | | | This way we'll be able to use the same one script for either ARC CPU. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: relocate - minor refactoring and clean-upAlexey Brodkin2015-01-15-11/+5
| | | | | | | | | | * use better symbols for relocatable region boundaries ("__image_copy_start" instead of "CONFIG_SYS_TEXT_BASE") * remove useless debug messages because they will only show up in case of both problem (when normal "if" branch won't be taken) and DEBUG take place which is pretty rare situation. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* arc: introduce separate section for interrupt vector tableIgor Guryanov2015-01-15-31/+46
| | | | | | | | | | | | | | | | | | Even though existing implementation works fine in preparation to submission of ARCv2 architecture we need this change. In case of ARCv2 interrupt vector table consists of just addresses of corresponding handlers. And if those addresses will be in .text section then assembler will encode them as everything in .text section as middle-endian and then on real execution CPU will read swapped addresses and will jump into the wild. Once introduced new section is situated so .text section remains the first which allows us to use common linker option for linking everything to a specified CONFIG_SYS_TEXT_BASE. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: add dependences on MMU presenceAlexey Brodkin2015-01-15-4/+18
| | | | | | | | | Depending on MMU presence in CPU there're differences in HW behavior. For example address of instruction that caused exception is put in ECR register if MMU exists and in ERET register otherwise. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: interrupts - fix mask setupIgor Guryanov2015-01-15-1/+1
| | | | | | | | | | | To disable interrupts we need to reset corresponding flags in STATUS32 register. For this we need to OR flags for interrupts level1 and level2 and then AND with current value in STATUS32. Before that implementation was incorrect. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: add ECR (exception cause register) outputIgor Guryanov2015-01-15-4/+7
| | | | | | | | | | | Exception cause register (ECR) contains value that describes a reason for exception that has happened. This helps a lot to figure-out what went wrong. Now we print this register contents when dumping registers. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: check caches existence before useIgor Guryanov2015-01-15-0/+31
| | | | | | | | | | | | | | | | | | | | Some cache operations ({i|d}cache_{enable|disable|status} or flush_dcache_all) are built and used even if CONFIG_SYS_{I|D}CACHE_OFF is set. This is required for force disable of caches on early boot. What if something was executed before U-boot and enabled caches (low-level bootloaders, previously run kernel etc.)? But if CPU doesn't really have caches any attempt to access cache-related AUX registers triggers instruction error exception. So for convenience we'll try to avoid exceptions by checking if CPU actually has caches (we check separately data and instruction cache existence) at all. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* arc: introduce "mdbtrick" targetAlexey Brodkin2015-01-09-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MetaWare debugger (MDB) is still used as a primary tool for interaction with target via JTAG. Moreover some very advanced features are not yet implemented in GDB for ARC (and not sure if they will be implemnted sometime soon given complexity and rare need for those features for common user). So if we're talking about development process when U-Boot is loaded in target memory not by low-level boot-loader but manually through JTAG chances are high developer uses MDB for it. But MDB doesn't support PIE (position-independent executable) - it will refuse to even start - that means no chance to load elf contents on target. Then the only way to load U-Boot in MDB is to fake it by: 1. Reset PIE flag in ELF header This is simpe - on attempt to open elf MDB checks header and if it doesn't match its expectation refuces to use provided elf. 2. Strip all debug information from elf If (1) is done then MDB will open elf but on parsing of elf's debug info it will refuse to process due to debug info it cannot understand (symbols with PIE relocation). Even though it could be done manually (I got it documented quite a while ago here http://www.denx.de/wiki/U-Boot/ARCNotes) having this automated way is very convenient. User may build U-Boot that will be loaded on target via MDB saying "make mdbtrick". Then if we now apply the manipulation MDB will happily start and will load all required sections into the target. Indeed there will be no source-level debug info available. But still MDB will do its work on showing disassembly, global symbols, registers, accessing low-level debug facilities etc. As a summary - this is a pretty dirty hack but it simplifies life a lot for us ARc developers. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de>
* Kbuild: introduce Makefile in arch/$ARCH/Daniel Schwierzeck2014-12-08-0/+8
| | | | | | | | | | | | | | | Introduce a Makefile under arch/$ARCH/ and include it in the top Makefile (similar to Linux kernel). This allows further refactoringi like moving architecture-specific code out of global makefiles, deprecating config variables (CPU, CPUDIR, SOC) or deprecating arch/$ARCH/config.mk. In contrary to Linux kernel, U-Boot defines the ARCH variable by Kconfig, thus the arch Makefile can only included conditionally after the top config.mk. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-1/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arc: Fix printf size_t format related warnings (again...)Vasili Galka2014-08-26-0/+4
| | | | | | | | | | | The basic idea: Define size_t using the __SIZE_TYPE__ compiler-defined type. For detailed explanation see similar patch for the nios2 arch: http://patchwork.ozlabs.org/patch/379938/ Signed-off-by: Vasili Galka <vvv444@gmail.com> Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
* kconfig: delete redundant CONFIG_${ARCH} definitionMasahiro Yamada2014-07-30-1/+1
| | | | | | | CONFIG_${ARCH} is defined by Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-30-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* ARC: enable CONFIG_SYS_BOOT_RAMDISK_HIGHAlexey Brodkin2014-06-03-0/+1
| | | | | | | This enables relocation of initrd to the end of available DDR before Linux kernel start-up as it is done in other architectures. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* common/board_f: Initialized global data for generic boardYork Sun2014-05-12-0/+2
| | | | | | | | | | | | | Some platforms (tested on mpc85xx, mpc86xx) use global data before calling function baord_inti_f(). The data should not be cleared later. Any arch which uses global data in generic board board_init_f() should define CONFIG_SYS_GENERIC_GLOBAL_DATA. Signed-off-by: York Sun <yorksun@freescale.com> CC: Scott Wood <scottwood@freescale.com> CC: Simon Glass <sjg@chromium.org> CC: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org>
* kbuild: delete redundant LDSCRIPT definitionMasahiro Yamada2014-03-12-2/+0
| | | | | | | | | | | | | $(SRCTREE)/$(CPUDIR)/u-boot.lds is our default location of arch-specific linker script. Remove redundant definitions in arch/{arc,microblaze,openrisc}/config.mk. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Michal Simek <monstr@monstr.eu>
* kbuild: fix CROSS_COMPILE settings in config.mkMasahiro Yamada2014-03-04-2/+6
| | | | | | | | | | | | | | | | The syntax CROSS_COMIPLE ?= <cross_compiler_prefix> does not work because config.mk is parsed after exporting CROSS_COMPILE. Like Linux Kernel's arch/$(ARCH)/Makefile, we must write as follows: ifeq ($(CROSS_COMPILE),) CROSS_COMPILE := <cross_compiler_prefix> endif Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arc: fix relocation for big-endian targetAlexey Brodkin2014-02-21-0/+4
| | | | | | | | | | | | | | | In case of little-endian ARC700 instructions (which may include target address) are encoded as middle-endian. That's why it's required to swap bytes after read and ten right before write back. But in case of big-endian ARC700 instructions are encoded as a plain big-endian. Thus no need for byte swapping. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Tom Rini <trini@ti.com> cc: Noam Camus <noamc@ezchip.com>
* arc: remove "hardware.h"Alexey Brodkin2014-02-20-10/+0
| | | | | | | | | | | | | | This file was only required for compilation of designware_i2c driver. Since explicit inclusion of "hardware.h" is now removed from the driver we may safely remove this empty header as well. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Armando Visconti <armando.visconti@st.com>
* arc: add library functionsAlexey Brodkin2014-02-07-0/+846
| | | | | | | | | | | These are library functions used by ARC700 architecture. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
* arc: add cpu filesAlexey Brodkin2014-02-07-0/+734
| | | | | | | | | Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
* arc: add architecture header filesAlexey Brodkin2014-02-07-0/+593
These are header files used by ARC700 architecture. Also note that "arch-arc700/hardware.h" is only required for compilation of "designware_i2c" driver which refers to "asm/arch/hardware.h". It would be good to fix mentioned driver sometime soon but it will cause changes in ARM board configs that use "designware_i2c". Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
generated by cgit v1.1 at 2024-11-08 22:24:43 +0000