summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
| * | nios2: divide nios2-io.h into each specific drivers and remove itThomas Chou2014-08-30-159/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The nios2-io.h defines hardware registers and bits of several FPGA IP cores. It could be divided in to the specific drivers, including altera timer, altera sysid, altera uart and altera jtag uart. The altera pio and altera spi drivers use their own hardware definitions. The removal of nios2-io.h will help modularity and maintenance. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
| * | nios2: remove epled driverThomas Chou2014-08-30-47/+0
| | | | | | | | | | | | | | | | | | The epled driver was replaced by altera_pio and gpio_led. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
* | | nomadik: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-16/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Nomadik board select menu to nomadik/Kconfig. Move also common settings (CONFIG_SYS_CPU="arm926ejs" and CONFIG_SYS_SOC="nomadik"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | highbank: kconfig: move common settingsMasahiro Yamada2014-08-30-5/+6
| | | | | | | | | | | | | | | | | | | | | Move Highbank-specific settings to highbank/Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Rob Herring <robh@kernel.org>
* | | orion5x: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-12/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Orion5x board select menu to orion5x/Kconfig. Move also common settings (CONFIG_SYS_CPU="arm926ejs" and CONFIG_SYS_SOC="orion5x"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | | keystone: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-22/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Keystone board select menu to keystone/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="keystone"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Vitaly Andrianov <vitalya@ti.com>
* | | omap5: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-36/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the OMAP5 board select menu to omap5/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="omap5"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
* | | omap4: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-36/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the OMAP4 board select menu to omap4/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="omap4"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
* | | omap3: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-289/+140
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the OMAP3 board select menu to omap3/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="omap3 Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com>
* | | davinci: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-189/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Davinci board select menu to davinci/Kconfig. Move also common settings (CONFIG_SYS_CPU="arm926ejs" and CONFIG_SYS_SOC="davinci"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com>
* | | exynos: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-117/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Exynos board select menu to exynos/Kconfig. Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="exynos"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* | | kirkwood: kconfig: refactor Kconfig and defconfigMasahiro Yamada2014-08-30-232/+127
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the KirkWood board select menu to kirkwood/Kconfig. Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and CONFIG_SYS_SOC="kirkwood"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Prafulla Wadasdkar <prafulla@marvell.com> Cc: Luka Perkov <luka@openwrt.org>
* | | versatile: kconfig: move common settingsMasahiro Yamada2014-08-30-83/+30
| | | | | | | | | | | | | | | | | | Move Versatile-specific settings to versatile/Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | rmobile: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-64/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Rmobile board select menu to rmobile/Kconfig. Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="rmobile"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* | | tegra: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-246/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Tegra board select menu to tegra/Kconfig. Insert the Tegra SoC select menu between the arch select and the board select. Architecture select |-- Tegra Platform (Tegra) |- Tegra SoC select (Tegra20 / 30 / 114 / 124) |- Board select Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows: config TEGRA bool select SPL Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com>
* | | zynq: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-118/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Zynq board select menu to zynq/Kconfig. Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="zynq"). Refactor board/xilinx/zynq/MAINTAINERS too. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Michal Simek <michal.simek@xilinx.com>
* | | arm: Add missing .vectors section to linker scriptsBenoît Thébaudeau2014-08-30-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 41623c9 'arm: move exception handling out of start.S files' missed some linker scripts. Hence, some boards no longer had exception handling linked since this commit. Restore the original behavior by adding the .vectors section to these linker scripts. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | | arm/km: disable subpage write for km_kirkwood_pci and kmsuv31 targetHolger Brunck2014-08-30-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Newer FLASH types used on these boards don't allow writing of subpages. So disable subpage write in the NAND driver. Additionally we need to tell the UBI layer in the kernel that he also should only write 2048 bytes. This is done with an additional command line parameter for the kernel commandline. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* | | arm/kirkwood/nand: allow forced disabling for subpage writesHolger Brunck2014-08-30-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make it configurable to disable subpage writes like the DaVinci NAND driver already does. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Scott Wood <scottwood@freescale.com>
* | | vexpress_aemv8a.h: Enable CONFIG_CMD_BOOTI and CONFIG_CMD_UNZIPTom Rini2014-08-30-0/+2
| | | | | | | | | | | | | | | | | | Add support for booting Images and for unzipping Image.gz files. Signed-off-by: Tom Rini <trini@ti.com>
* | | vexpress_aemv8a.h: Clean up the configTom Rini2014-08-30-8/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | - Drop DEBUG - Drop defines we can use the default of. - Provide a larger malloc pool. - Correct default locations for kernel / initrd / device tree Signed-off-by: Tom Rini <trini@ti.com>
* | | cmd_bootm.c: Add 'booti' for ARM64 Linux kernel ImagesTom Rini2014-08-30-1/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The default format for arm64 Linux kernels is the "Image" format, described in Documentation/arm64/booting.txt. This, along with an optional gzip compression on top is all that is generated by default. The Image format has a magic number within the header for verification, a text_offset where the Image must be run from, an image_size that includes the BSS and reserved fields. This does not support automatic detection of a gzip compressed image. Signed-off-by: Tom Rini <trini@ti.com>
* | | arm64: Correct passing of Linux kernel argsTom Rini2014-08-30-3/+5
| | | | | | | | | | | | | | | | | | | | | The Documentation/arm64/booting.txt document says that pass in x1/x2/x3 as 0 as they are reserved for future use. Signed-off-by: Tom Rini <trini@ti.com>
* | | arm: convert Cygnus and NSP boards to KconfigSteve Rae2014-08-30-0/+72
| | | | | | | | | | | | | | | | | | Convert the bcm958300k and the bcm958622hr boards from "boards.cfg" to Kconfig. Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: add Cygnus and NSP boardsScott Branden2014-08-30-0/+244
| | | | | | | | | | | | | | | | | | | | | | | | | | | The bcm_ep board configuration is used by a number of boards including Cygnus and NSP. Add builds for the bcm958300k and the bcm958622hr boards. Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: bcmnsp: Add bcmnsp u-architectureScott Branden2014-08-30-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | Base support for the Broadcom NSP SoC. Based on iproc-common and the SoC specific reset function. Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: bcmcygnus: Add bcmcygnus u-architectureScott Branden2014-08-30-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | Base support for the Broadcom Cygnus SoC. Based on iproc-common and the SoC specific reset function. Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: iproc: Initial commit of iproc architecture codeScott Branden2014-08-30-0/+423
| | | | | | | | | | | | | | | | | | | | | | | | The iproc architecture code is present in several Broadcom chip architectures, including Cygnus and NSP. Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: vf610: add NFC clock supportStefan Agner2014-08-30-0/+15
| | | | | | | | | | | | | | | | | | | | | Add NFC (NAND Flash Controller) clock support and enable them at board initialization time. Signed-off-by: Stefan Agner <stefan@agner.ch>
* | | arm: vf610: add NFC pin muxStefan Agner2014-08-30-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | Add pin mux for NAND Flash Controller (NFC). NAND can be connected using 8 or 16 data lines, this patch adds pin mux entries for all 16 data lines. Signed-off-by: Stefan Agner <stefan@agner.ch>
* | | MAINTAINERS: change the status of vexpress board to OrphanMasahiro Yamada2014-08-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The email address of Matt Waddel is no longer working. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Alexei Fedorov <alexie.fedorov@arm.com>
* | | ARM: Fix overflow in MMU setupMarek Vasut2014-08-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch fixes a corner case where adding size to DRAM start resulted in a value (1 << 32), which in turn overflew the u32 computation, which resulted in 0 and it therefore prevented correct setup of the MMU tables. The addition of DRAM bank start and it's size can end up right at the end of the address space in the special case of a machine with enough memory. To prevent this overflow, shift the start and size separately and add them only after they were shifted. Hopefully, we only have systems in tree which have DRAM size aligned to 1MiB boundary. If not, this patch would break such systems. On the other hand, such system would be broken by design anyway. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | | arm: bcm281xx: add board with Ethernet capabilitySteve Rae2014-08-30-0/+9
| | | | | | | | | | | | | | | | | | Add board which has Broadcom StarFighter2 Ethernet capability. Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: bcm281xx: net: Add Ethernet DriverJiandong Zheng2014-08-30-0/+1536
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom SoC(s) and: - supports multiple MAC blocks, - provides support for the Broadcom GMAC. This driver requires MII and PHYLIB. Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
* | | arm: bcm281xx: Add Ethernet Clock supportJiandong Zheng2014-08-30-0/+181
| | | | | | | | | | | | | | | | | | | | | | | | Enable Ethernet clock when Broadcom StarFighter2 Ethernet block (CONFIG_BCM_SF2_ETH) is enabled. Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
* | | ARM: enable ARMv7 virt support for the Arndale boardAndre Przywara2014-08-30-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To enable hypervisors utilizing the ARMv7 virtualization extension on the Arndale board, add the simple SMP pen address writer function and add the required configuration variables to switch all cores to HYP mode before launching the OS. This allows booting KVM and Xen directly from u-boot. Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@linaro.org> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* | | arm: ep9315: Add .vectors section to lds and remove obsolete ldsSergey Kostanbaev2014-08-30-58/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | However ep9315 don't use interrupt vectors during startup, but _startup symbol is used inside uboot to calculate actual monitor size. Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com> Cc: albert.u.boot@aribaud.net
* | | socfpga: cleanup socfpga_dw_mmcPavel Machek2014-08-30-4/+4
| | | | | | | | | | | | | | | | | | | | | Cleanups as suggested by wd on mailing list. Signed-off-by: Pavel Machek <pavel@denx.de> Acked-by: Chin Liang See <clsee@altera.com>
* | | socfpga: initialize designware ethernetPavel Machek2014-08-30-9/+51
| | | | | | | | | | | | | | | | | | | | | | | | Enable initialization fo designware ethernet controller. With this patch, ethernet works in my configuration, provided I set ethernet address in the environment. Signed-off-by: Pavel Machek <pavel@denx.de>
* | | socfpga: Fix SOCFPGA build error for Altera dev kitChin Liang See2014-08-29-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To fix the build error when build for Altera dev kit, not virtual target. At same time, set the build for Altera dev kit as default instead virtual target. With that, U-Boot is booting well and SPL still lack of few drivers. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Pavel Machek <pavel@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* | | socfpga: fix clock manager register definitionPavel Machek2014-08-29-101/+107
| | | | | | | | | | | | | | | | | | | | | | | | | | | Structure defining clock manager hardware was wrong, leading to wrong registers being accessed and hang in MMC init. This fixes structure to match hardware. Signed-off-by: Pavel Machek <pavel@denx.de>
* | | arm: include config.h in arch/arm/lib/vectors.SChristian Riesch2014-08-29-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | config.h is required for CONFIG_SYS_DV_NOR_BOOT_CFG. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Heiko Schocher <hs@denx.de> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
* | | ARM:asm:io.h use static inlineJeroen Hofstee2014-08-29-6/+6
|/ / | | | | | | | | | | | | | | | | | | | | When compiling u-boot with W=1 the extern inline void for read* is likely causing the most noise. gcc / clang will warn there is never a actual declaration for these functions. Instead of declaring these extern make them static inline so it is actually declared. cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2014-08-29-392/+679
|\ \
| * | pcm051: use ti_am335x_common.h configMatwey V. Kornilov2014-08-25-136/+4
| | | | | | | | | | | | | | | | | | Include general configs/ti_am335x_common.h and drop redundant #defines. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
| * | ARM: DRA: Enable VTT regulatorLokesh Vutla2014-08-25-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * | am335x_evm: Convert CONFIG_CONS_INDEX into a menu choiceTom Rini2014-08-25-43/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead - Add choice and help text to board/ti/am335x/Kconfig - Correct comment about IDK in board/ti/am335x/mux.c - Remove am335x_evm_uart* defconfig files as they're just variations on a config option now. Signed-off-by: Tom Rini <trini@ti.com>
| * | cm-t54: convert to generic boardDmitry Lifshitz2014-08-25-0/+3
| | | | | | | | | | | | | | | | | | | | | Use generic board setup functions by defining CONFIG_SYS_GENERIC_BOARD. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
| * | cm-t54: fix eMMC boot mode checkDmitry Lifshitz2014-08-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from eMMC boot partition corresponds to BOOT_DEVICE_MMC2 omap_bootmode, while BOOT_DEVICE_MMC2_2 corresponds to the user data partition boot. Fix mmc_get_env_part() boot mode check to use a correct value. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
| * | cm-t54: fix EEPROM read return value checkDmitry Lifshitz2014-08-25-2/+2
| | | | | | | | | | | | | | | | | | | | | Fix cl_eeprom_read_mac_addr() return value check. Fix long line codding style issue in board_init(). Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
generated by cgit v1.1 at 2024-12-03 11:39:19 +0000