summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
* ENGR00315894-38 MX6 Sabreauto:Add IPUv3 splash screen supportYe.Li2014-06-17-16/+217
| | | | | | | | | | | | | | | | This patch adds IPUv3 splash screen support for the MX6Q/SDL Sabreauto platforms. The default display is the Hannstar-XGA LVDS panel. Users may set the uboot variable 'panel' to be 'HDMI' to switch to use HDMI splash screen. To avoid duplicate configures on different sabre platforms, this patch moves the IPUv3 splash screen relevant configures to the head file 'mx6qsabre_common.h'. Also, this patch modifies the condition to build in EPDC splash screen feature in order to avoid the build break due to the migration of the IPUv3 splash screen relevant configures. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-37 MX6 SabreSD: Correct IPU DI pix fmt for LDBYe.Li2014-06-17-12/+3
| | | | | | | | | | | | | The DC mapping for LVDS666 is different from that for RGB666. Currently, we set IPU DI pixel format to be LVDS666 and set LDB data width to be 24bit. This happens to make the display work normally somehow. But, the two configurations are wrong and don't match with each other. This patch corrects the IPU DI output pixel format from LVDS666 to RGB666 and LDB data width from 24bit to 18bit. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-36 MX6 SabreSD: Disable HDMI detectYe.Li2014-06-17-8/+1
| | | | | | | | | | | | | | As the HDMI splash screen feature is not well supported, we should not set it to be the default display. In case, users leave the 'panel' uboot environment variable empty and connect the board with a HDMI monitor, the HDMI detect funtion will work and enable the HDMI splash screen. So, this patch disables HDMI detect function so that users may only explicitly set the 'panel' variable to be 'HDMI' to use HDMI splash screen. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-35 i.mx6: Fix issue in HAB clock settingYe.Li2014-06-17-9/+9
| | | | | | Should use the address of one register when calling "readl"/"writel". Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-34 imx6:dlsabresd/slevk Fix build break when enables EPDCYe.Li2014-06-17-311/+316
| | | | | | | -Use the new pins' name for imx6dl. -Change the read/write to registers by using register structure. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-33 gpmi: use the same ECC strength as used in the kernelYe.Li2014-06-17-14/+13
| | | | | | | | | | | | Current code use the hardcoded ECC strength which is not aligned with the kernel. This patch use the same ECC strength as used in the kernel. We do not support the NAND whose OOB size is larger then 512bytes. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-32 i.mx6:sabreauto/sabresd Set the mmcdev for various boot devicesYe.Li2014-06-17-1/+15
| | | | | | | | | | | For the SPI/WEIM NOR, it can't store all the images into it due to it's capacity, we need one default mmc device to load the left image or rootfs. The end user need change the default setting according to their needs. For NAND/SATA boot, the storage is big enough to hold all the stuff. For SD/MMC boot, mmcdev is dynamiclly created due to the boot SD/MMC slot. Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-31 mx6slevk support mfgtoolsYe.Li2014-06-17-0/+12
| | | | | | | support mfgtools Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-30 i.mx6:sabreauto/sabresd/arm2/evk Change boot command to bootmYe.Li2014-06-17-30/+30
| | | | | | Change the bootz command in boot script to bootm Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-29 configs/mx6sabre_common: remove HW PROTECTION for NOR flashYe.Li2014-06-17-1/+0
| | | | | | | | | The CONFIG_SYS_FLASH_PROTECTION will mark env partion of the NOR flash to RO, which will cause some problems for the tools such as MFG, thus turn it off to make life easier. Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-28 i.mx6:sabreauto/sabresd/arm2/evk Enable the ↵Ye.Li2014-06-17-25/+6
| | | | | | | | | | CONFIG_SUPPORT_EMMC_BOOT Since we need to support eMMC plugin card on SD slots, enable the CONFIG_SUPPORT_EMMC_BOOT for all imx6 boards and remove the EMMC_ENV script. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-27 i.mx6slevk/i.mx6qarm2: Change the MMC dev settingsYe.Li2014-06-17-2/+4
| | | | | | | | 1. Add CONFIG_SYS_MMC_ENV_PART to save env in user area. 2. Set the image load partition to first VFAT partition. 3. Set the kernel rootfs partition to second partition. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-26 i.mx6qarm2: Add the kernel FDT Loading supportYe.Li2014-06-17-3/+38
| | | | | | Add the fdt address and file name. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-25 i.mx6sl: Modify load address and fdt addressYe.Li2014-06-17-2/+2
| | | | | | Change the loadaddr to 0x80800000 and fdt_addr to 0x83000000 Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-24 imx6:sabreauto/sabresd/arm2/evk Add the secureboot supportYe.Li2014-06-17-0/+48
| | | | | | | | | | | | | In order to support the secureboot, please turn on the CONFIG_SECURE_BOOT in "include/configs/mx6qsabre_common.h" ---- sabreauto or sabresd "include/configs/mx6slevk.h" ---- imx6slevk "include/configs/mx6qarm2.h" ---- arm2 By default, the CONFIG_SECURE_BOOT is disabled. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-23 imx6slevk: add the plugin mode supportYe.Li2014-06-17-1/+203
| | | | | | | | | This patch add the plugin mode support for imx6slevk board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6slevk.h Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-22 imx6dl/solo:sabresd: add the plugin mode supportYe.Li2014-06-17-47/+14
| | | | | | | | | This patch add the plugin mode support for imx6dl and imx6solo sabresd. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6qsabre_common.h Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-21 imx6/sabreauto: add the plugin mode supportYe.Li2014-06-17-42/+514
| | | | | | | | | This patch add the plugin mode support for sabreauto board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6qsabre_common.h Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-20 imx6/arm2: add the plugin mode supportYe.Li2014-06-17-3/+279
| | | | | | | | | This patch add the plugin mode support for arm2 board. In order to enable the plugin mode, please turn on the CONFIG_USE_PLUGIN in the include/configs/mx6qarm2.h Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-19 iMX6 Disable the L2 before chaning the PL310 latencyYe.Li2014-06-17-0/+3
| | | | | | | | | | | The Latency parameters of PL310 Tag RAM latency control register and Data RAM Latency control register are set in L2 cache enable. Setting these registers must have PL310 not enabled. But when using Plugin mode boot, the PL310 is enabled by bootrom. Thus, disable the PL310 before this setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-18 i.mx6: increase the console I/O buffer to 1KYe.Li2014-06-17-4/+4
| | | | | | | | Current console buffer is 256 bytes long, it is too small. increase it to 1K. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-17 imx6q:sabresd/sabreauto: add SATA supportYe.Li2014-06-17-12/+231
| | | | | | | | This patch adds the SATA support for i.mx6qsabresd and i.mx6qsabreauto board Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-16 env_mmc: add the dynamtic mmc dev supportYe.Li2014-06-17-9/+23
| | | | | | | | This patch add the support to load/save env to the slot which was used as the boot media by dynamic detection. Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-15 i.mx6:sabreauto: Remove duplicated I2C settingsYe.Li2014-06-17-8/+3
| | | | | | | | 1. The i2c2 bus is setup twice, remove the duplication. 2. The i2c settings are duplicated in mx6qsabreauto.h and mx6sabre_common.h, remove it from mx6qsabreauto.h Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-14 i.mx6:sabreauto/sabresd/slevk Remove unused CONFIG_SYS_I2C_SLAVEYe.Li2014-06-17-6/+3
| | | | | | | The CONFIG_SYS_I2C is enabled on i.mx6 boards. So the CONFIG_SYS_I2C_SLAVE becomes to unused. Remove this setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-13 i.mx6q:sabresd: update the DDR scriptYe.Li2014-06-17-123/+95
| | | | | | | | | This patch update the DDR script to the ddr-scripts-rel.git based on the top of the following commit: 7cd1c3b Removed the duplicate script files Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-12 i.mx6:sabreauto/sabresd: Change the MMC settingsYe.Li2014-06-17-8/+7
| | | | | | | | | | | | | | | | | | | | | | | 1. Change CONFIG_MMCROOT to mmcblk0p2. Kernel always sets the first availiable MMC/SD device to mmcblk0 2. Make the MMC ENV DEV/PART independent of ENV_IS_IN_MMC 3. Add the CONFIG_SYS_MMC_ENV_PART to 0 (user area) for u-boot env saving. CONFIG_SYS_MMC_ENV_PART: was used to tell the u-boot which emmc (boot)partition to be used for the env_mmc.Usually, the emmc card will have 2 boot partitions, boot1 and boot2. 0: means user area 1: means boot partition 1 2: means boot partition 2 If user want to use the boot partition to store the u-boot env, please change the CONFIG_SYS_MMC_ENV_PART to which boot partition you want. 4. Add the CONFIG_SYS_MMC_IMG_LOAD_PART for the partition number where the kernel and DTB will load from. At default, it is the first partition in VFAT format. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-11 i.mx6:shutdown vddpu and pcie phy to save powerYe.Li2014-06-17-0/+31
| | | | | | | | shutdown vddpu and pcie phy to save power Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-10 i.mx6:sabreauto: Add the GPMI nand supportYe.Li2014-06-17-3/+122
| | | | | | | | | | | Add the GPMI nand support to the iMX6 sabreauto: --Enable the GPMI NAND at default. --Enable the clocks --Set the default environment for nand boot Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-9 i.mx6q/dl/solo:sabreauto: Add the WEIM-NOR supportYe.Li2014-06-17-9/+143
| | | | | | | Add the WEIM-NOR support Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-8 imximage: Fix imximage bug for EIM-NOR bootYe.Li2014-06-17-0/+7
| | | | | | | | | | | The load region size of EIM-NOR are defined to 0. For this case, the parameter "imximage_init_loadsize" must be calculated. The imximage tool implements the calculation in the "imximage_generate" function, but the following function "imximage_set_header" resets the value and not calculate. This bug cause some fields of IVT head are not correct, for example the boot_data and DCD overlay the application area. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-7 i.mx6q/dl/solo: sabresd/sabreauto: Add the SPI-NOR supportYe.Li2014-06-17-35/+97
| | | | | | | | | | This patch adds the SPI-NOR support for the i.mx6q/dl/solo:sabresd/auto board: - Support the SPI-NOR function with sf command, - Support the enviroment from SPI-NOR when CONFIG_SYS_BOOT_SPINOR Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-6 i.mx6:sabreauto: Add the i.MX6solo sabreauto supportYe.Li2014-06-17-0/+123
| | | | | | | | | | | | | This patch is to add the i.MX6solo sabreauto support, The i.MX6solo sabreauto board configuration has the following difference with i.MX6dl sabreauto: - DDR bus width: 32bit - DDR capacity: 1024M Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-5 i.mx6:sabreauto: Add the i.MX6DL sabreauto board supportYe.Li2014-06-17-1/+148
| | | | | | | | | | | | | This patch is to add the i.MX6DL sabreauto board support. i.MX6DL sabreauto board share the same design with i.MX6Q sabreauto board except the SOC difference. The DDR script has been updated to the v0.2 version from ddr-scripts-rel.git, the commit based on is: bfd157a Updated MX6DL and MX6DQ ARD and SabreSD scripts Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-4 iMX6Q:SABREAUTO: Disable the DTB for MX6QSABREAUTO boardYe.Li2014-06-17-3/+0
| | | | | | | The DTB for mx6qsabreauto is empty. To support more iMX6 sabreauto boards, remove this DTB in building. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-3 iMX6q:SABREAUTO: Rename the imximage.cfg to mx6q.cfgYe.Li2014-06-17-2/+2
| | | | | | | Rename the imximage.cfg to mx6q.cfg. No function change at all. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-2 iMX6:SABRESD: Add the i.MX6solo SABRESD board supportYe.Li2014-06-17-0/+131
| | | | | | | | | | The i.MX6solo sabre-sd board configuration has the following difference with i.MX6dl sabre-sd: - DDR bus width: 32bit - DDR capacity: 512M Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-1 iMX6q/dl:SABREAUTO/SABRESD: Refactor configurations for more ↵Ye.Li2014-06-17-15/+161
| | | | | | | | | | | | | iMX6 boards 1. Make the DDR size configurable based on the boards.cfg 2. Make the FDT file configurable based on the boards.cfg 3. Add DDR and boot configuration script for iMX6dl. Change default boot from SD card. The DDR script has been updated to the v1.5 version from ddr-scripts-rel commit: bfd157a Updated MX6DL and MX6DQ ARD and SabreSD scripts. Signed-off-by: Ye.Li <B37916@freescale.com>
* image: add support for Android's boot image formatSebastian Siewior2014-06-13-6/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Android boot-image format. The header file is from the Android project and got slightly alterted so the struct + its defines are not generic but have something like a namespace. The header file is from bootloader/legacy/include/boot/bootimg.h. The header parsing has been written from scratch and I looked at bootloader/legacy/usbloader/usbloader.c for some details. The image contains the physical address (load address) of the kernel and ramdisk. This address is considered only for the kernel image. The "second image" defined in the image header is currently not supported. I haven't found anything that is creating this. v3 (Rob Herring): This is based on http://patchwork.ozlabs.org/patch/126797/ with the following changes: - Rebased to current mainline - Moved android image handling to separate functions in common/image-android.c - s/u8/char/ in header to fix string function warnings - Use SPDX identifiers for licenses - Cleaned-up file source information: android_image.h is from file include/boot/bootimg.h in repository: https://android.googlesource.com/platform/bootable/bootloader/legacy The git commit hash is 4205b865141ff2e255fe1d3bd16de18e217ef06a usbloader.c would be from the same commit, but it does not appear to have been used for any actual code. v4: - s/andriod/android/ - Use a separate flag ep_found to track if the entry point has been set rather than using a magic value. Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Tom Rini <trini@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
* ENGR00315499-22 video: ipu: wait for DP SF end irq when disabling sync BG flowLiu Ying2014-06-13-22/+22
| | | | | | | | | | | Instead of waiting for DC triple buffer to be cleared, this patch changes to wait for a relevant DP sync flow end irq when disabling sync BG flows. In this way, we align the implement to the FSL internal IPUv3 driver. After applying this patch, the uboot hang up issue at the arch_preboot_os stage on the MX6DL platforms is not observed any more. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-21 HDMI: splash screen function enhancementNitin Garg2014-06-13-31/+72
| | | | | | | | | | | | -Change HDMI video mode to VGA. -Add pixel clock fraction part setting in IPU driver, fix video mode timing issue. -Add overflow state clear workaround, fix kernel hang in HDMI driver issue. -Correct IPU clock to 264MHz. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-20 ARM:imx6 Fix USDHC driver bug in PIO modeYe.Li2014-06-13-15/+10
| | | | | | | | | | | | | | | | | When configure the USDHC driver to PIO mode by defining "CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail. Two bugs in the driver to cause the issue: 1. The read buffer was invalidated after reading from DATAPORT register, which should be only applied to DMA mode. The valid data in cache was overwritten by physical memory. 2. The watermarks are not set in PIO mode, will cause according state not be set. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit e2ced39867a3001390bd23069e56b513ed268bb0) Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-19 Fix eMMC fast boot hang issueYe.Li2014-06-13-9/+37
| | | | | | | | | | | | | When booting in eMMC fast boot, the uboot v2013.04 always hangs. The root cause is that MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors. This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode. Signed-off-by: Ye Li <b37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-18 driver:MAX7310: Add GPIO expander driver for MAX7310Ye.Li2014-06-13-1/+242
| | | | | | | | | | | | Implement simple functionalities for MAX7310 GPIO input and output. Because MAX7310 is a off-chip device and need to co-exist with on-chip GPIO, new APIs are added specifically for expander device. CONFIG_MAX7310_IOEXP is used to enable the MAX7310 driver. The I2C related configurations also need to set together. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-17 ARM:imx6sl:evk Add SPI NOR flash boot and access supportNitin Garg2014-06-13-3/+63
| | | | | | | | | | | Add BSP codes to support SPI NOR flash read, write and erase by using "sf" command. In addition, add a new configuration "mx6slevk_spinor" for building the uboot that can be booted from SPI NOR flash and stored the environments variables in it. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-16 I2C: add I2C support on Sabre- boardNitin Garg2014-06-13-1/+206
| | | | | | | | - add I2C support on Sabresd ,Sabreauto board. - add pfuze init code based on I2C transfer in Sabre* board file. Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-15 ARM:imx6sl:evk Add USB HOST supportNitin Garg2014-06-13-1/+45
| | | | | | | | Enable the USB EHCI for the imx6slevk board. Add VBUS control pin settings and related BSP codes. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-14 ARM:imx6:sabresd/arm2 Add USB HOST BSP supportNitin Garg2014-06-13-2/+99
| | | | | | | | | Enable the USB EHCI on sabresd and arm2 boards to support USB mass storage device. Pins are configured in board_ehci_hcd_init for VBUS control. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-13 ARM:imx6:EHCI Update OTG support for imx6slNitin Garg2014-06-13-5/+11
| | | | | | | | | Set Power polarity in CTRL register to active-high to control the off-chip power switch. Update USB base address to support imx6sl. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-12: ARM: MSL: add i2c0 support for imx6sl evkNitin Garg2014-06-13-0/+106
| | | | | | | | - Add i2c0 support for imx6sl evk platform. - Read pmic device ID and revsion ID. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
generated by cgit v1.1 at 2024-11-19 14:18:02 +0000