summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* keystone2: ecc: add ddr3 error detection and correction supportVitaly Andrianov2014-10-23-0/+319
| | | | | | | | | | | | | | | | | | | | This patch adds the DDR3 ECC support to enable ECC in the DDR3 EMIF controller for Keystone II devices. By default, ECC will only be enabled if RMW is supported in the DDR EMIF controller. The entire DDR memory will be scrubbed to zero using an EDMA channel after ECC is enabled and before u-boot is re-located to DDR memory. An ecc_test environment variable is added for ECC testing. If ecc_test is set to 0, a detection of 2-bit error will reset the device, if ecc_test is set to 1, 2-bit error detection will not reset the device, user can still boot the kernel to check the ECC error handling in kernel. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* ARM: keystone: msmc: extend functionality of SESVitaly Andrianov2014-10-23-0/+60
| | | | | | | | | | Add functions to set/get SES PMAX values of Pivilege ID pair. Also add msmc module definitions. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* dma: ti-edma3: introduce edma3 driverKhoronzhuk, Ivan2014-10-23-0/+506
| | | | | | | | | | | | | | | | The EDMA3 controller’s primary purpose is to service data transfers that you program between two memory-mapped slave endpoints on the device. Typical usage includes, but is not limited to the following: - Servicing software-driven paging transfers (e.g., transfers from external memory, such as SDRAM to internal device memory, such as DSP L2 SRAM) - Servicing event-driven peripherals, such as a serial port - Performing sorting or sub-frame extraction of various data structures - Offloading data transfers from the main device DSP(s) - See the device-specific data manual for specific peripherals that are accessible via the EDMA3 controller Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* board: k2e_evm: add network supportHao Zhang2014-10-23-1/+75
| | | | | | | | | | This patch adds network support code and enables keystone_net driver usage for k2e_evm evaluation board. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* ARM: keystone: clock: add support for K2E SoCsKhoronzhuk, Ivan2014-10-23-4/+15
| | | | | | | | For K2E and K2L SoCs clock output from PASS PLL has to be enabled after NETCP domain and PA module are enabled. So create new function for that and call it after PA module is enabled. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: increase PHY auto negotiate timeKhoronzhuk, Ivan2014-10-23-5/+31
| | | | | | | | | | | The new Marvel PHY (88E1514) used on K2L/K2E EVM requires longer time to auto negotiate with SoC's SGMII port. It can take about 3 sec to up the PHY after reset, so add code to expose sgmii auto negotiation waiting process. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: add Keystone2 K2E SoC supportKhoronzhuk, Ivan2014-10-23-0/+8
| | | | | | | | | The Keystone2 Edison SoC uses the same keystone net driver. This patch adds opportunity to use it by K2E SoCs. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_serdes: add keystone K2E SoC supportKhoronzhuk, Ivan2014-10-23-0/+14
| | | | | | | | | Keystone2 Edison SoC uses the same keystone SerDes driver. This patch adds support for K2E SoCs. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* ARM: keystone2: keysonte_nav: add support for K2E SoCKhoronzhuk, Ivan2014-10-23-0/+13
| | | | | | | | | | Keystone2 Edison SoC uses the same keystone navigator, but uses different NETCP PktDMA definitions. This patch adds required definitions. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: use general get link functionKhoronzhuk, Ivan2014-10-23-46/+5
| | | | | | | | | | | | The phy framework has function to get link, so use it instead of own implementation. There is no reason to check SGMII link while sending each packet, phy link is enough. Check SGMII link only while ethernet open. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: register eth PHYs on MDIO busKhoronzhuk, Ivan2014-10-23-3/+24
| | | | | | | | | | | | | | | | | As MDIO bus has been added we can register PHYs with it. After registration, the PHY driver will be probed according to the hardware on board. Startup PHY at the ethernet open. Use phy_startup() instead of keystone_get_link_status() when eth open, as it verifies PHY link inside and SGMII link is checked before. For K2HK evm PHY configuration at init was absent, so don't enable phy config at init for k2hk evm. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: register MDIO busKhoronzhuk, Ivan2014-10-23-38/+55
| | | | | | | | | | | | Currently MDIO framework is not used to configure Ethernet PHY. As result some of already implemented functions are duplicated. So register MDIO bus in order to use it. On that stage it's just registered, it'll be used as we start to use PHY framework. Use mdio bus read/write/reset functions in the driver. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: use mdio_reset functionKhoronzhuk, Ivan2014-10-23-14/+2
| | | | | | | | Don't use mdio_enable twice while eth open. Also rename it to keystone2_mdio_reset as more appropriate name. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: phy: print a number of phy that is not foundKhoronzhuk, Ivan2014-10-23-1/+1
| | | | | | | | In case when several Ethernet ports are supported it's convenient to see the number of phy that is not found. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* soc: keystone_serdes: generalize configuration mechanismKhoronzhuk, Ivan2014-10-23-47/+65
| | | | | | | | | | The cmu, comlane, lane configuration mechanism are similar for sub systems as well such as PCI or sRIO, but they have different values based on input clock and output bus rate. According to this compact driver to simplify adding different configuration settings based on clock and rate. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* soc: keystone_serdes: generalize to be used by other sub systemsHao Zhang2014-10-23-42/+156
| | | | | | | | | | SerDes driver is used by other sub systems like PCI, sRIO etc. So modify it to be more general. The SerDes driver provides common API's that can also be extended for other peripherals SerDes configurations. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* soc: keystone_serdes: enhance to use cmu/comlane/lane specific configurationsHao Zhang2014-10-23-82/+94
| | | | | | | | Enhance the driver to use cmu/comlane/lane specific configurations instead of 1 big array of configuration. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* soc: keystone_serdes: create a separate SGMII SerDes driverKhoronzhuk, Ivan2014-10-23-138/+158
| | | | | | | | | | | | | This patch split the Keystone II SGMII SerDes related code from Ethernet driver and create a separate SGMII SerDes driver. The SerDes driver can be used by others keystone subsystems like PCI, sRIO, so move it to driver/soc/keystone directory. Add soc specific drivers directory like in the Linux kernel. It is going to be used by keysotone soc specific drivers. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: remove redundant code from keystone_net.cKhoronzhuk, Ivan2014-10-23-17/+9
| | | | | | | | | | | | | | | | Remove unused tx_send_loop variable. Removes duplicated get_link_status() call from the keystone2_eth_send_packet(). The emac_gigabit_enable() is called at opening Ethernet and there is no need to enable it on sending each packet. So remove that call from keystone2_eth_send_packet() as well. The calling of power/clock up functions are mostly the responsibility of SoC/board code, so move these functions to appropriate place. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: increase MDIO clock frequencyVitaly Andrianov2014-10-23-1/+1
| | | | | | | | | | With MAC_PHY sgmii configuration, u-boot checks PHY link status before sending each packet. Increasing MDIO frequency increases overall tftp speed. We set it to maximum 2.5MHz. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: move header file from arch to ti-commonKhoronzhuk, Ivan2014-10-23-260/+261
| | | | | | | | | | The header file for the driver should be in correct place. So move it to "arch/arm/include/asm/ti-common/keystone_net.h" and correct driver's external dependencies. At the same time align and correct some definitions. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: add support for NETCP v1.5Khoronzhuk, Ivan2014-10-23-62/+98
| | | | | | | | | | | | | | | | | Currently the network driver is used only by k2hk evm board. The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e contain NETCP v1.5. So driver should be able to work with such kind of NETCP. This commit adds this opportunity. The main difference in masks and some registers, the logic is the same, so only definitions should be changed. To differentiate between versions add KS2_NETCP_V1_0 and KS2_NETCP_V1_5. Also remove unused and no more needed defines. The port number is specific for each board so move this parameter to configuration. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* net: keystone_net: remove SoC specific emac_regs structureHao Zhang2014-10-23-20/+3
| | | | | | | | | | This patch removes K2HK SOC specifc emac_regs structure, it uses soc specific register offset to keep the network driver common across all the Keystone II EVMs. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* configs: ks2_evm: enable misc_init_rKhoronzhuk, Ivan2014-10-23-0/+1
| | | | | | | Currently keystone has misc_init_r where all DSPS are turned off by default. So enable this function. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone2: k2l-evm: add board supportHao Zhang2014-10-23-0/+219
| | | | | | | | This patch adds Keystone II Lammar (K2L) EVM board support. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone2: enable OSR clock domain for K2L SoCHao Zhang2014-10-23-0/+76
| | | | | | | This patches enables the On-chip Shared Ram clock domain for K2L SoC. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* ARM: keystone2: spl: move board specific codeHao Zhang2014-10-23-66/+43
| | | | | | | | | The initialization of PLLs is a part of board specific code, so move it appropriate places. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone2: msmc: add MSMC cache coherency support for K2L SOCHao Zhang2014-10-23-9/+19
| | | | | | | | | This patch adds Keystone II Lamar (K2L) SoC specific definitions to support MSMC cache coherency. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone2: clock: add K2L clock definitions and commandsHao Zhang2014-10-23-0/+232
| | | | | | | | | This patch adds clock definitions and commands to support Keystone II K2L SOC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* ARM: keystone2: add K2L device hardware definitionsHao Zhang2014-10-23-2/+87
| | | | | | | | | This patch adds hardware definitions specific to Keystone II Lamar (K2L) SoC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* ARM: cmd_clock: generalize command usage descriptionKhoronzhuk, Ivan2014-10-23-61/+61
| | | | | | | | The usage description of commands refers to headers of sources, that is not correct. This patch is intended to fix it. Also generalize code in order to reduce SoC dependent #ifdefs. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone: usb: add support of usb xhciWingMan Kwok2014-10-23-1/+379
| | | | | | | | | | | | | Add support of usb xhci. xHCI controls all USB speeds of the Host mode, that is, the SS through the SS PHY, as well as the HS, FS, and LS through the USB2 PHY. xHCI replaces and supersedes all previous host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not backwards compatible with any of them. The USB3SS’s USB Controller is fully compliant with xHC. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* dma: keystone_nav: generalize driver usageKhoronzhuk, Ivan2014-10-23-89/+98
| | | | | | | | | | | | | | | | | | | The keystone_nav driver is general driver intended to be used for working with queue manager and pktdma for different IPs like NETCP, AIF, FFTC, etc. So the it's API shouldn't be named like it works only with one of them, it should be general names. The names with prefix like netcp_* rather do for drivers/net/keystone_net.c driver. So it's good to generalize this driver to be used for different IP's and delete confusion with real NETCP driver. The current netcp_* functions of keystone navigator can be used for other settings of pktdma, not only for NETCP. The API of this driver is used by the keystone_net driver to work with NETCP, so net driver also should be corrected. For convenience collect pkdma configurations in drivers/dma/keystone_nav_cfg.c. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* dma: keystone_nav: move keystone_nav driver to driver/dma/Khoronzhuk, Ivan2014-10-23-29/+59
| | | | | | | | | | | | | | The keystone_nav is used by drivers/net/keystone_net.c driver to send and receive packets, but currently it's placed at keystone arch sources. So it should be in the drivers directory also. It's separate driver that can be used for sending and receiving pktdma packets by others drivers also. This patch just move this driver to appropriate directory and doesn't add any functional changes. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone2: keystone_nav: don't use hard addresses in netcp_pktdmaKhoronzhuk, Ivan2014-10-23-29/+27
| | | | | | | | | Use definitions in netcp_pktdma instead direct addresses. The definitions can be set specifically for SoC, so there is no reason to check SoC type while initialization. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* keystone2: keystone_nav: don't use hard addresses in qm_configKhoronzhuk, Ivan2014-10-23-32/+30
| | | | | | | | Use definitions in qm_config. The definitions can be set specifically for SoC, so there is no reason to check SoC type while initialization. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
* Merge git://git.denx.de/u-boot-dmTom Rini2014-10-22-2162/+7808
|\
| * dm: serial: Support driver model in pl01x driverSimon Glass2014-10-22-0/+73
| | | | | | | | | | | | | | | | Add driver model support in this driver, using platform data provided by the board. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
| * dm: serial: Tidy up the pl01x driverSimon Glass2014-10-22-140/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adjust the driver so that leaf functions take a pointer to the serial port register base. Put all the global configuration in the init function, and use the same settings from then on. This makes it much easier to move to driver model without duplicating the code, since with driver model we use platform data rather than global settings. The driver is compiled with either the CONFIG_PL010_SERIAL or CONFIG_PL011_SERIAL option and this determines the uart type. With driver model this needs to come in from platform data, so create a new CONFIG_PL01X_SERIAL config which brings in the driver, and adjust the driver to support both peripheral variants. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
| * dm: rpi: Convert GPIO driver to driver modelSimon Glass2014-10-22-23/+182
| | | | | | | | | | | | | | | | | | Convert the BCM2835 GPIO driver to use driver model, and switch over Raspberry Pi to use this, since it is the only board. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
| * dm: core: Add support for simple-busSimon Glass2014-10-22-0/+35
| | | | | | | | | | | | | | Add a driver for the simple-bus nodes, which allows devices within these nodes to be bound. Signed-off-by: Simon Glass <sjg@chromium.org>
| * dm: imx: Move cm_fx6 to use driver model for serial and GPIOSimon Glass2014-10-22-0/+21
| | | | | | | | | | | | | | | | | | Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an example. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
| * dm: imx: serial: Support driver model in the MXC serial driverSimon Glass2014-10-22-25/+159
| | | | | | | | | | | | | | Add driver model support with this driver. Boards which use this driver should define platform data in their board files. Signed-off-by: Simon Glass <sjg@chromium.org>
| * dm: imx: gpio: Support driver model in MXC gpio driverSimon Glass2014-10-22-1/+303
| | | | | | | | | | | | | | | | | | | | Add driver model support with this driver. In this case the platform data is in the driver. It would be better to put this into an SOC-specific file, but this is best attempted when more boards are moved over to use driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * arm: mx6: cm_fx6: use gpio requestNikita Kiryanov2014-10-22-39/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use gpio_request for all the gpios that are utilized by various subsystems in cm-fx6, and refactor the relevant init functions so that all gpios are requested during board_init(), not during subsystem init, thus avoiding the need to manage gpio ownership each time a subsystem is initialized. The new division of labor is: During board_init() muxes are setup and gpios are requested. During subsystem init gpios are toggled. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * dm: imx: i2c: Use gpio_request() to request GPIOsSimon Glass2014-10-22-0/+25
| | | | | | | | | | | | | | | | | | | | GPIOs should be requested before use. Without this, driver model will not permit the GPIO to be used. Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * imx: Add error checking to setup_i2c()Simon Glass2014-10-22-13/+55
| | | | | | | | | | | | | | Since this function can fail, check its return value. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
| * dm: serial: Put common code into separate functionsSimon Glass2014-10-22-15/+17
| | | | | | | | | | | | | | Avoid duplicating the code which deals with getc() and putc(). It is fairly simple, but may expand later. Signed-off-by: Simon Glass <sjg@chromium.org>
| * initcall: Display error number when an error occursSimon Glass2014-10-22-3/+5
| | | | | | | | | | | | | | | | Now that some initcall functions return a useful error number, display it when something goes wrong. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * dm: core: Allow a list of devices to be declared in one stepSimon Glass2014-10-22-0/+4
| | | | | | | | | | | | | | The U_BOOT_DEVICE macro allows the declaration of a single U-Boot device. Add an equivalent macro to declare an array of devices, for convenience. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-11-09 09:00:46 +0000