summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* configs: dra7xx: Enable lp873x optionsKeerthy2016-12-04-0/+6
| | | | | | | | DRA71-evm uses LP873x regulator. Enable lp873x PMIC config options. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* configs: dra7xx: Enable pmic/regulator optionsLokesh Vutla2016-12-04-0/+5
| | | | | | | Enable pmic/regulator config options. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* configs: dra7xx: hs: Enable DM_ETHLokesh Vutla2016-12-04-0/+1
| | | | | | | Enable DM_ETH for hs boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* configs: ti_omap5_common: Select dtb name for dra71xNishanth Menon2016-12-04-0/+2
| | | | | | | Select dtb name for dra71x-evm. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: dts: dra71x-evm: Add DT supportLokesh Vutla2016-12-04-4/+237
| | | | | | | Add DT support for dra71-evm and built it as part of FIT image. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: dts: dra7xx: sync DT with latest LinuxLokesh Vutla2016-12-04-640/+1683
| | | | | | | Sync all dra7xx based dts files with latest Linux Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP4+: Add support for getting pbias info from boardLokesh Vutla2016-12-04-48/+82
| | | | | | | | | | | | | Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based boards to enable mmc regulator. This is not true always like in case of DRA71x-evm. So get this information based on the board. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c] Signed-off-by: Tom Rini <trini@konsulko.com>
* board: ti: dra71x-evm: Add PMIC supportKeerthy2016-12-04-0/+77
| | | | | | | | | | | | | | | Add the pmic_data for LP873x PMIC which is used to power up dra71x-evm. Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating the efuse registers only to use OPP_NOM irrespective of any CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined. [1] http://www.ti.com/product/DRA718/technicaldocuments Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: dra72: Introduce optimization for rgmii timing for rev CNishanth Menon2016-12-04-25/+50
| | | | | | | | | | | Rev C version of EVM does require IODelay to be configured for RGMII pins in MANUAL_1 configuration. Update the same based on PG2.0 initial simulation values. Data based on PCT_DRA72x_SR2.0_SR1.0_v1.3.0.7 Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: dra71x-evm: Add mux settingsLokesh Vutla2016-12-04-1/+206
| | | | | | | | Add mux and iodelay settings for dra71x-evm. Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: dra71x-evm: Add epprom supportLokesh Vutla2016-12-04-0/+5
| | | | | | | | | | | | | | The dra71x-evm is a board based on TI's DRA718 processor targeting BOM-optimized entry infotainment systems such as display audio and is a software compatible derivative of the highly successful DRA74 and DRA72 processor families. More information can be found here[1]. Add epprom detection for dra71-evm. [1] http://www.ti.com/product/dra718 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Fixup DSPEVE, IVA and GPU clock frequencies based on OPPSuman Anna2016-12-04-0/+136
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support to update the device-tree blob to adjust the DSP and IVA DPLL clocks pertinent to the selected OPP choice, with the default being OPP_NOM. The voltage settings are done in u-boot, but the actual clock configuration itself is done in kernel because of the following reasons: 1. SoC definition constraints us to NOT to do dynamic voltage scaling ever after the initial avs0 setting in bootloader - so the voltage must be set in bootloader. 2. The voltage level must be set even if the IP blocks like GPU/DSP are unused. 3. The IVA, GPU and DSP DPLLs are not essential for u-boot functionality, and similar DPLL clock configuration code has been cleaned up in v2014.10 u-boot release. See commit, 02c41535b6a4 ("ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL"). The non-essential DPLLs are configured within the kernel during the clock init step when parsing the device tree and creating the clock devices. This approach meets both the u-boot and kernel needs. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Subhajit Paul <subhajit_paul@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Redefine voltage and efuse macros per OPP using KconfigSuman Anna2016-12-04-13/+127
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Redefine the macros used to define the voltage values and the efuse register offsets based on OPP for all the voltage domains. This is done using Kconfig macros that can be set in a defconfig or selected during a config step. This allows a voltage domain to be configured/set to a corresponding voltage value depending on the OPP selection choice. The Kconfig choices have been added for MPU, DSPEVE, IVA and GPU voltage domains, with the MPU domain restricted to OPP_NOM. The OPP_OD and OPP_HIGH options will be added when the support for configuring the MPU clock frequency is added. The clock configuration for other voltage domains is out of scope in u-boot code. The CORE voltage domain does not have separate voltage values and efuse register offset at different OPPs, while the MPU voltage domain only has different efuse register offsets for different OPPs, but uses the same voltage value. Any different choices of OPPs for voltage domains on common ganged-rails is automatically taken care to select the corresponding highest OPP voltage value. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP4+: Add support for dynamically selecting OPPsLokesh Vutla2016-12-04-104/+254
| | | | | | | | | | | It can be expected that different paper spins of a SoC can have different definitions for OPP and can have their own constraints on the boot up OPP for each voltage rail. In order to have this flexibility, add support for dynamically selecting the OPP voltage based on the board to handle any such exceptions. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap4_sdp4430: Disable SPL_OS_BOOTTom Rini2016-12-04-1/+0
| | | | | | We are tight on space on this board so drop SPL_OS_BOOT Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-dmTom Rini2016-12-03-160/+790
|\
| * cmd: crosec: Move cros_ec_decode_region helper to cmd/cros_ec.cMoritz Fischer2016-12-02-25/+23
| | | | | | | | | | | | | | | | | | | | | | The cros_ec_decode_region() function is only used in combination with the crosec cmds. Move the function to the correct place. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Simon Glass <sjg@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: u-boot@lists.denx.de Acked-by: Simon Glass <sjg@chromium.org>
| * drivers: usb: musb: add ti musb host driver with driver model supportMugunthan V N2016-12-02-0/+191
| | | | | | | | | | | | | | | | | | Add a TI MUSB host driver with driver model support and the driver will be bound by the MUSB wrapper driver based on the dr_mode device tree entry. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * drivers: usb: musb: adopt musb backend driver to driver modelMugunthan V N2016-12-02-22/+23
| | | | | | | | | | | | | | | | | | | | Currently all backend driver ops uses hard coded physical address, so to adopt the driver to DM, add device pointer to ops call backs so that drivers can get physical addresses from the usb driver priv/plat data. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * am33xx: board: probe misc drivers to register musb devicesMugunthan V N2016-12-02-0/+7
| | | | | | | | | | | | | | | | | | MUSB wrapper driver is bound as MISC device and underlying usb devices are bind to usb drivers based on dr_mode, so probing the MISC wrapper driver to register musb devices. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * drivers: usb: musb: add ti musb misc driver for wrapperMugunthan V N2016-12-02-0/+74
| | | | | | | | | | | | | | | | Add a misc driver for MUSB wrapper, so that based on dr_mode the USB devices can bind to USB host or USB device drivers. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * am33xx: board: do not register usb devices when CONFIG_DM_USB is definedMugunthan V N2016-12-02-1/+4
| | | | | | | | | | | | | | Do not register usb devices when CONFIG_DM_USB is define. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * configs: am335x: usb: do not define CONFIG_DM_USB for splMugunthan V N2016-12-02-0/+1
| | | | | | | | | | | | | | | | Since OMAP's spl doesn't support DM currently, do not define CONFIG_DM_USB for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * rtc: Add RTC chip pcf2127 supportMeng Yi2016-12-02-0/+114
| | | | | | | | | | | | | | This driver compatible with pcf2127 and pcf2129 Signed-off-by: Meng Yi <meng.yi@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * dm: core: Add dev_get_addr_size_index() to retrieve addr and sizeStefan Roese2016-12-02-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | The currently available functions accessing the 'reg' property of a device only retrieve the address. Sometimes its also necessary to retrieve the size described by the 'reg' property. This patch adds the new function dev_get_addr_size_index() which retrieves both, the address and the size described by the 'reg' property. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
| * libfdt: replace ARCH_FIXUP_FDT with ARCH_FIXUP_FDT_MEMORYMasahiro Yamada2016-12-02-11/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e2f88dfd2d96 ("libfdt: Introduce new ARCH_FIXUP_FDT option") allows us to skip memory setup of DTB, but a problem for ARM is that spin_table_update_dt() and psci_update_dt() are skipped as well if CONFIG_ARCH_FIXUP_FDT is disabled. This commit allows us to skip only fdt_fixup_memory_banks() instead of the whole of arch_fixup_fdt(). It will be useful when we want to use a memory node from a kernel DTB as is, but need some fixups for Spin-Table/PSCI. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Acked-by: Simon Glass <sjg@chromium.org> Fixed build error for x86: Signed-off-by: Simon Glass <sjg@chromium.org>
| * cmd/fdt: fix uncallable systemsetup commandFabien Parent2016-12-02-12/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The function that is processing the 'fdt' parameters is one big if-else if. In order to be able to type command faster only the first few letter are checked to know which block of code to execute. For systemsetup, the block of code that was executed was always the wrong one and ended up in a failure. } else if (argv[1][0] == 's') { process "fdt set" command } else if (strncmp(argv[1], "sys", 3) == 0) { process "fdt systemsetup" command. } When typing "fdt systemsetup", the code that was executed was the code for "fdt set". This commit fix this issue by moving the "else if" for systemsetup before the else if for "fdt set". This allow us to keep compatibility with any script that make use of "fdt s" to set node values. Signed-off-by: Fabien Parent <fparent@baylibre.com> Acked-by: Simon Glass <sjg@chromium.org>
| * drivers: usb: gadget: ether: prepare driver for driver model migrationMugunthan V N2016-12-02-21/+52
| | | | | | | | | | | | | | prepare driver for driver model migration Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * drivers: usb: gadget: ether: use net device priv to pass usb ether privMugunthan V N2016-12-02-25/+21
| | | | | | | | | | | | | | | | | | Use net device priv to pass usb ether priv and use it in net device ops callback. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * drivers: usb: gadget: ether: consolidate global devices to single structMugunthan V N2016-12-02-27/+26
| | | | | | | | | | | | | | | | | | | | Consolidate the net device, usb eth device and gadget device struct to single struct and a single global variable so that the same can be passed as priv of ethernet driver. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * drivers: usb: gadget: ether: adopt to usb driver modelMugunthan V N2016-12-02-0/+36
| | | | | | | | | | | | | | | | Convert usb ether gadget to adopt usb driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * drivers: usb: gadget: ether: access network_started using local variableMugunthan V N2016-12-02-5/+5
| | | | | | | | | | | | | | | | | | network_started of struct eth_dev can be accessed using local variable dev and no reason to access it with the global struct. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * dm: blk: Fix get_desc to return block device descriptorMichal Simek2016-12-02-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Current get_desc() implementation is not able to succesfully finish and return pointer to block device descriptor. Also function always return non zero value even device is found. The patch fills block device descriptor and return 0 if device is found. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * dm: core: Handle global_data moving in SPLSimon Glass2016-12-02-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | When CONFIG_SPL_STACK_R is enabled, and spl_init() is called before board_init_r(), spl_relocate_stack_gd() will move global_data to a new place in memory. This affects driver model since it uses a list for the uclasses. Unless this is updated the list will become invalid. When looking for a non-existent uclass, such as when adding a new one, the loop in uclass_find() may continue forever, thus causing a hang. Add a function to correct this rather obscure bug. Signed-off-by: Simon Glass <sjg@chromium.org>
| * buildman: Rename do_build to config_onlySimon Glass2016-12-02-5/+5
| | | | | | | | | | | | | | This variable name is needlessly confusion. Adjust it to use a 'positive' name instead. Signed-off-by: Simon Glass <sjg@chromium.org>
| * buildman: Clean up odd characters on the terminalSimon Glass2016-12-02-1/+1
| | | | | | | | | | | | | | At present buildman leaves behind a few characters during its progress updates, which looks odd. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org>
| * buildman: Squash useless output from -KSimon Glass2016-12-02-13/+38
| | | | | | | | | | | | | | | | | | | | When using #define CONFIG_SOME_OPTION, the value it set to '1'. When using defconfig (i.e. CONFIG_SOME_OPTION=y) the value is set to 'y'. This results in differences showing up with -K. These differences are seldom useful. Adjust buildman to suppress these differences by default. Signed-off-by: Simon Glass <sjg@chromium.org>
| * buildman: Add documentation for CONFIG checkingSimon Glass2016-12-02-0/+37
| | | | | | | | | | | | | | The -K option is not mentioned in the README at present. Add some notes to describe how this is used. Signed-off-by: Simon Glass <sjg@chromium.org>
| * buildman: Add an option to just create the configSimon Glass2016-12-02-7/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Normally buildman does a full build of a board. This includes creating the u-boot.cfg file which contains all the configuration options. Buildman uses this file with the -K option, to show differences in effective configuration for each commit. Doing a full build of U-Boot just to create the u-boot.cfg file is wasteful. Add a -D option which causes buildman to only create the configuration. This is enough to support use of -K and can be done much more quickly (typically 5-10 times faster). Signed-off-by: Simon Glass <sjg@chromium.org>
| * Makefile: Add a target to create the .cfg filesSimon Glass2016-12-02-0/+3
| | | | | | | | | | | | | | | | | | A common requirement when converting CONFIG options to Kconfig is to check that the effective configuration has not changed due to the conversion. Add a target which creates this configuration (in the form of u-boot.cfg) but does not build U-Boot. This speeds up the checking. Signed-off-by: Simon Glass <sjg@chromium.org>
| * sandboxfs: Fix resource leakTom Rini2016-12-02-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | Now that we free resources in sandbox_fs_ls Coverity is letting us know that in some cases we might leak. So in case of error we should still let os_dirent_free free anything that was allocated. Fixes: 86167089b71c ("sandbox/fs: Free memory allocated by os_dirent_ls") Reported-by: Coverity (CID: 153450) Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * tpm: tpm_tis_lpc: Add support for AT97SC3204George McCollister2016-12-02-9/+28
| | | | | | | | | | | | | | | | | | The Atmel AT97SC3204 is also TIS compliant. Modify the tpm_tis_lpc driver to check for the vid/did used by the Atmel AT97SC3204 and report an appropriate description. Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * cmd/tpm_test: Fix misleading code indentationStefan Brüns2016-12-02-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GCC 6.2 reasonably complains about the current code: ../cmd/tpm_test.c: In function ‘do_tpmtest’: ../cmd/tpm_test.c:540:3: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation] for (i = 0; i < argc; i++) ^~~ ../cmd/tpm_test.c:542:4: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’ printf("\n------\n"); ^~~~~~ Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by: Simon Glass <sjg@chromium.org> Updated to remove C99 variable decl: Signed-off-by: Simon Glass <sjg@chromium.org>
* | cmd: move CMD_PXE to KconfigYann E. MORIN2016-12-03-9/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, CMD_PXE is forcibly enabled in config_distro_defaults.h, so that general purpose distributions can rely on it being defined. This header is included, under conditions or not, by various archs or famillies of archs / SoCs. However, it is very possible that boards based on those SoCs will not have a physical ethernet connector at all, even if the have a MAC; for example, the Nanopi Neo AIR (sunxi H3) does not. It is also possible that network booting is absolutely not necessary for a device. However, it is not possible to disable the PXE command, as it is forcibly enabled and is non-configurable. But it turns out we already have a config option to build a distro-ready image, in the name of DISTRO_DEFAULTS. Move CMD_PXE out of the hard-coded config_distro_defaults.h into a Kconfig option, that gets selected by DISTRO_DEFAULTS when it is set. Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr> Cc: Joe Hershberger <joe.hershberger@ni.com> [trini: Make it select MENU, run moveconfig.py] Signed-off-by: Tom Rini <trini@konsulko.com>
* | Enable DISTRO_DEFAULT on platforms that missed it beforeTom Rini2016-12-03-711/+67
| | | | | | | | | | | | | | | | | | A number of platforms had been using the distro default feature before it was moved to Kconfig but did not enable the new Kconfig option when it was enabled. This caused a regression in terms of features and this introduces breakage when more things move to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
* | cmd: Convert CMD_BOOTMENUTom Rini2016-12-03-14/+13
| | | | | | | | | | | | Also convert MENU while we're in here. Signed-off-by: Tom Rini <trini@konsulko.com>
* | board: ti: am57xx: add FIT image TEE processingAndrew F. Davis2016-12-03-0/+7
| | | | | | | | | | | | | | | | Populate the corresponding TEE image processing call to be performed during FIT loadable processing. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | board: ti: dra7xx: add FIT image TEE processingAndrew F. Davis2016-12-03-0/+7
| | | | | | | | | | | | | | | | | | Populate the corresponding TEE image processing call to be performed during FIT loadable processing. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: omap5: Add OPTEE node to fdtAndrew F. Davis2016-12-03-1/+34
| | | | | | | | | | | | | | | | Add an OPTEE node to the FDT when TEE installation has completed successfully. This informs the kernel of the presence of OPTEE. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: omap5: Add TEE loading supportHarinarayan Bhatta2016-12-03-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | secure_tee_install is used to install and initialize a secure TEE OS such as Linaro OP-TEE into the secure world. This function takes in the address where the signed TEE image is loaded as an argument. The signed TEE image consists of a header (struct tee_header), TEE code+data followed by the signature generated using image signing tool from TI security development package (SECDEV). Refer to README.ti-secure for more information. This function uses 2 new secure APIs. 1. PPA_SERV_HAL_TEE_LOAD_MASTER - Must be called on CPU Core 0. Protected memory for TEE must be reserved before calling this function. This API needs arguments filled into struct ppa_tee_load_info. The TEE image is authenticated and if there are no errors, the control passes to the TEE entry point. 2. PPA_SERV_HAL_TEE_LOAD_SLAVE - Called on other CPU cores only after a TEE_LOAD_MASTER call. Takes no arguments. Checks if TEE was successfully loaded (on core 0) and transfers control to the same TEE entry point. The code at TEE entry point is expected perform OS initialization steps and return back to non-secure world (U-Boot). Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.1 at 2024-09-19 14:08:10 +0000