summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* imx6: geam6ul: Add default mtd nand partition tableJagan Teki2016-12-16-0/+2
| | | | | | | | | | | | | | | | | geam6ul> mtdparts device nand0 <nand>, # parts = 6 0: spl 0x00200000 0x00000000 0 1: uboot 0x00200000 0x00200000 0 2: env 0x00100000 0x00400000 0 3: kernel 0x00400000 0x00500000 0 4: dtb 0x00100000 0x00900000 0 5: rootfs 0x1f600000 0x00a00000 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: geam6ul: Enable MTD device supportJagan Teki2016-12-16-0/+6
| | | | | | | | | Enable MTD device, partition and command support. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: geam6ul: Add NAND supportJagan Teki2016-12-16-1/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add NAND support for Engicam GEAM6UL board. Boot Log: -------- U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28) Trying to boot from NAND NAND : 256 MiB U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100) CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 42C Reset cause: WDOG Model: Engicam GEAM6UL DRAM: 128 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 * Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: geam6ul: Add I2C supportJagan Teki2016-12-16-0/+3
| | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam GEAM6UL module. geam6ul> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 geam6ul> i2c dev 0 Setting bus to 0 geam6ul> i2c dev Current bus is 0 geam6ul> i2c speed 100000 Setting bus speed to 100000 Hz geam6ul> i2c probe Valid chip addresses: 2C geam6ul> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: dts: imx6ul-geam: Add I2C nodesJagan Teki2016-12-16-0/+28
| | | | | | | | | Add I2C nodes for Engicam GEAM6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki2016-12-16-1/+594
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: dts: Add devicetree for i.MX6ULJagan Teki2016-12-16-0/+943
| | | | | | | | | | | | | Add i.MX6UL dtsi support from Linux. Here is the last commit: "ARM: dts: add gpio-ranges property to iMX GPIO controllers" (sha1: bb728d662bed0fe91b152550e640cb3f6caa972c) Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6: Add I2C supportJagan Teki2016-12-16-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam i.CoreM6 qdl board. icorem6qdl> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl> i2c dev 2 Setting bus to 2 icorem6qdl> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl> i2c probe Valid chip addresses: 2C icorem6qdl> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Heiko Schocher <hs@denx.de>
* i2c: mxc: Make 'no gpio pinctrl state' print as debugJagan Teki2016-12-16-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Some I2C bus devicetree nodes, doesn't require to have gpio pinctrl so replace the dev_info to debug so the print never comes on the console and for bus that uses gpio pinctrl anyway have dev_err. Before: ------ U-Boot> i2c dev 1 Setting bus to 1 i2c bus 1 at 0x21a4000, no gpio pinctrl state. After: ------ U-Boot> i2c dev 1 Setting bus to 1 Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Heiko Schocher <hs@denx.de>
* i2c: mxc: Print hex instead of decimal for bus addressJagan Teki2016-12-16-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Better to print the hex value for bus address instead of decimal, for more readbility on bus addressing. Before: ------ U-Boot> i2c dev 1 Setting bus to 1 i2c bus 1 at 35274752, no gpio pinctrl state. After: ------ U-Boot> i2c dev 1 Setting bus to 1 i2c bus 1 at 0x21a4000, no gpio pinctrl state. Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Heiko Schocher <hs@denx.de>
* i2c: Kconfig: Add SYS_I2C_MXC entryJagan Teki2016-12-16-0/+8
| | | | | | | | | | Added kconfig for SYS_I2C_MXC driver. Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6: Add custom splashscreen supportJagan Teki2016-12-16-0/+2
| | | | | | | | | | | Add custom splashscreen, engicam.bmp support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6: Add framebuffer supportJagan Teki2016-12-16-0/+131
| | | | | | | | | | Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* video: Kconfig: Add VIDEO_IPV3 entryJagan Teki2016-12-16-0/+7
| | | | | | | | | | Added kconfig entry for CONFIG_VIDEO_IPV3 driver. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* icorem6: Use CONFIG_DM_ETH supportJagan Teki2016-12-16-73/+1
| | | | | | | | | | | | Use CONFIG_DM_ETH and remove board_eth_init code from board files. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* ARM: dts: imx6qdl-icore: Add FEC supportJagan Teki2016-12-16-0/+24
| | | | | | | | | | Add FEC dts support for Engicam i.CoreM6 dql modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* dm: net: fec: Add .read_rom_hwaddrJagan Teki2016-12-16-9/+9
| | | | | | | | | | Add .read_rom_hwaddr on dm eth_ops. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* net: fec_mxc: Driver cleanupsJagan Teki2016-12-16-146/+83
| | | | | | | | | | | | | | | | | | - Remove exctra space - Add space - Add tab space - Fix single line comments quotes - Fix 'CHECK: Avoid CamelCase' - Fix 'CHECK: Alignment should match open parenthesis' - Fix 'WARNING: line over 80 characters' - Re-arrage header include files Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* net: fec_mxc: Convert into driver modelJagan Teki2016-12-16-26/+246
| | | | | | | | | | | | This patch add driver model support for fec_mxc driver. Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddrJagan Teki2016-12-16-3/+2
| | | | | | | | | | | fec_get_hwaddr never used eth_device argument, hence removed. Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn2016-12-16-2/+2557
| | | | | | | | | | | | | | | | Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
* imx: mx6sllevk: add plugin supportPeng Fan2016-12-16-0/+198
| | | | | | | Add plugin support for mx6sllevk board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* arm: imx: add i.MX6SLL EVK board supportPeng Fan2016-12-16-0/+1267
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* arm: dts: add i.MX6SLL device treePeng Fan2016-12-16-0/+1945
| | | | | | | Add i.MX6SLL device tree. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* pinctrl: imx6: support i.MX6SLLPeng Fan2016-12-16-0/+2
| | | | | | | | | | There two iomuxc for i.MX6SLL. One is normal IOMUXC, the other is for IOMUXC_SNVS. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* imx-common: lcdif: update lcdif regs for i.MX6SL/SLLPeng Fan2016-12-16-3/+4
| | | | | | | Update lcdif regs for i.MX6SL/SLL Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* OCOTP: Update OCOTP driver to support i.MX6SLLPeng Fan2016-12-16-8/+8
| | | | | | | | | | Add the i.MX6SLL support to OCOTP driver. The i.MX6SLL reuses the i.MX6ULL fuse, bank 7 and bank8 have 4 words each, and there is a hole between bank 5 and bank 6. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* mx6_common: correct loadaddr and text base for i.MX6SLLPeng Fan2016-12-16-1/+2
| | | | | | | Correct loadaddr and text base for i.MX6SLL Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6sll: add Kconfig entry for i.MX6SLLPeng Fan2016-12-16-0/+4
| | | | | | add Kconfig entry for i.MX6SLL Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx-common: cache: configure L2 Cache for i.MX6SLLPeng Fan2016-12-16-8/+9
| | | | | | | | If L2 cache configured as OCRAM, reset it. Switch to use runtime check. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6sll: add clock supportPeng Fan2016-12-16-7/+21
| | | | | | | Add clock support for i.MX6SLL. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: clock: gate clk before changing pix clk muxPeng Fan2016-12-16-23/+33
| | | | | | | | | | | The LCDIF Pixel clock mux is not glitchless, so need to gate before changing mux. Also change enable_lcdif_clock prototype with a new input parameter to indicate disable or enable. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6sl: add lcdif clock supportPeng Fan2016-12-16-19/+80
| | | | | | Add lcdif clock support for i.MX6SL. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx: mx6: lcdif: gate clock before changing muxPeng Fan2016-12-16-0/+10
| | | | | | | | The mux for the lcd clock is not glitchless, so need to first gate the clock before changing the mux. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6: fix mmdc ch0 clk for 6SLPeng Fan2016-12-16-0/+5
| | | | | | | | | | >From RM, per_periph2_clk_sel option3 is: "derive clock from 198MHz clock (divided 392MHz PLL2 PFD)." So fix it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6sll: add iomux settingsPeng Fan2016-12-16-5/+11
| | | | | | | | Add iomux settings for i.MX6 SLL Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye.Li <ye.li@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx-common: timer: add i.MX6SLL supportPeng Fan2016-12-16-3/+7
| | | | | | | Add i.MX6 SLL GPT timer support. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6sll: update register addressPeng Fan2016-12-16-27/+50
| | | | | | | Update register address for i.MX6 SLL Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: mx6sll: add pinmux header filesPeng Fan2016-12-16-0/+1021
| | | | | | | Add i.MX6SLL pinmux header files Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: add i.MX 6SLL CPU typePeng Fan2016-12-16-1/+5
| | | | | | | | Add i.MX6SLL cpu type. MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* configs: colibri_vf: Add fdt_fixup environment variableSanchayan Maity2016-12-16-3/+4
| | | | | | | | u-boot allows modifying a device tree after it is loaded into memory. Add fdt_fixup hook in u-boot environment which can facilitate such modifications. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
* board/liteboard: Add support for liteBoardMarcin Niestroj2016-12-16-0/+547
| | | | | | | | | | | | liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
* ARM: imx6ul: Add support for liteSOMMarcin Niestroj2016-12-16-0/+231
| | | | | | | | | | | | | | | | liteSOM is a System On Module (http://grinn-global.com/litesom/). It can't exists on its own, but will be used as part of other boards. Hardware specification: * NXP i.MX6UL processor * 256M or 512M DDR3 memory * optional eMMC (uSDHC2) Here we treat SOM similar to SOC, so we place it inside arch/arm/mach-* directory and make it possible to reuse initialization code (i.e. DDR, eMMC init) for all boards that use it. Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
* udoo_neo: Add Ethernet supportBreno Lima2016-12-16-2/+112
| | | | | | | | UDOO Neo boards has one FEC port connected to KSZ8091, add support for it. Tested on a UDOO Neo Full with "dhcp zImage" command. Signed-off-by: Breno Lima <breno.lima@nxp.com>
* udoo_neo: Add PFUZE300 PMIC supportBreno Lima2016-12-16-0/+156
| | | | | | | | UDOO Neo boards has a PFUZE300 connected to I2C1 bus. Tested on a UDOO Neo Full with "pmic PFUZE3000 dump" command. Signed-off-by: Breno Lima <breno.lima@nxp.com>
* power: pmic: Add Voltage configuration macroBreno Lima2016-12-16-0/+5
| | | | | | | Add pfuze3000 voltage configuration macro for SW1AB, SW3 and VLDO1/2 according to tables 53, 57 and 62 on PF3000 datasheet. Signed-off-by: Breno Lima <breno.lima@nxp.com>
* udoo_neo: Add thermal supportBreno Lima2016-12-16-0/+4
| | | | | | | Add thermal support on the Kconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
* udoo_neo: Remove console optionBreno Lima2016-12-16-1/+0
| | | | | | | It's not necessary to define the console option as we use the distro config. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
* udoo_neo: Remove mmcautodetect optionBreno Lima2016-12-16-1/+0
| | | | | | | It's not necessary to define the mmcautodetect as it is not used anywhere. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
* udoo_neo: Staticize board_string()Breno Lima2016-12-16-1/+1
| | | | | | | Change board_string() function to static because it's being used locally. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
generated by cgit v1.1 at 2024-11-19 09:59:01 +0000