summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* Merge branch 'next' of git://git.denx.de/u-boot-niosWolfgang Denk2010-09-07-7/+11
|\
| * nios2: fix out of reach case for do_resetThomas Chou2010-08-19-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is a limitation (or bug?) of nios2 toolchain. The nios2 gcc didn't generate correct code when the reset vector is passed as a constant. It just generated a direct "call", which was wrong when the reset vector was not located in the same 256MB span as u-boot. The "Nios II Processor Reference Handbook" said, "call can transfer execution anywhere within the 256 MByte range determined by PC31..28. The Nios II GNU linker does not automatically handle cases in which the address is out of this range." So we have to use registered "callr" instruction to do the job. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
| * nios2: fix bootm error on fdt argsThomas Chou2010-08-19-1/+1
| | | | | | | | | | | | | | | | We should check argv[3] only if there are enough args. Otherwise, it might cause invalid memory access fault. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk2010-09-07-624/+452
|\ \
| * | edminiv2: add I2C support using mvtwsi driverAlbert Aribaud2010-08-30-0/+11
| | | | | | | | | | | | | | | | | | Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar<prafulla@marvell.com> Acked-by: Heiko Schocher<hs@denx.de>
| * | i2c: rewrite mvtwsi, support orion5x and kirkwoodAlbert Aribaud2010-08-30-409/+341
| | | | | | | | | | | | | | | | | | | | | | | | | | | This rewrite of the mvtwsi driver is 25% smaller and much faster and simpler than the previous code. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar<prafulla@marvell.com> Acked-by: Heiko Schocher<hs@denx.de>
| * | i2c: rename kirkwood_i2c to mvtwsiAlbert Aribaud2010-08-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This driver is not kirkwood-specific and can also be used e.g. by orion5x. Rename to a SoC-neutral name. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar<prafulla@marvell.com> Acked-by: Heiko Schocher<hs@denx.de>
| * | suen3: remove CONFIG_HARD_I2C and related definesAlbert Aribaud2010-08-30-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | These are not used on this board, which uses soft I2C instead. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar<prafulla@marvell.com> Acked-by: Heiko Schocher<hs@denx.de>
| * | CMD_I2C: make alen=0 workReinhard Meyer2010-08-26-10/+7
| | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | omap2: i2c: remove redundant header definitionsNishanth Menon2010-08-23-106/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the register offset and common defines which are already present in drivers/i2c/omap24xx.h. All of these defines carry the same value even. Cc: Steve Sakoman <steve@sakoman.com> Cc: Heiko <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Wolfang Denk <wd@denx.de> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Steve Sakoman <steve@sakoman.com>
| * | omap2: i2c: add syss offsetNishanth Menon2010-08-23-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OMAP2420 ES2.3 trm defines syss register offset as 0x10. Add it. Cc: Steve Sakoman <steve@sakoman.com> Cc: Heiko <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Wolfang Denk <wd@denx.de> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Steve Sakoman <steve@sakoman.com>
| * | i2c: omap2+: change header guard to be genericNishanth Menon2010-08-23-2/+2
| |/ | | | | | | | | | | | | | | | | | | | | | | | | Make the header guard to be generic to stop conflicting with omap2 i2c header file arch/arm/include/asm/arch-omap24xx/i2c.h Cc: Steve Sakoman <steve@sakoman.com> Cc: Heiko <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Wolfang Denk <wd@denx.de> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Steve Sakoman <steve@sakoman.com>
* | powerpc/8xxx: Fix dma for 36bit addressingYork Sun2010-08-31-2/+6
| | | | | | | | | | | | | | Use more bits to support 36-bit addressing Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Fix parameters to support RDIMM for P2020DSYork Sun2010-08-31-2/+3
| | | | | | | | | | Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | fdt: call fdt_parent_offset fewer times while translating addressesScott Wood2010-08-19-37/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fdt_parent_offset() is an expensive operation, so we'd like to reduce unnecessary calls to it. Further, the practice of iterating up to the root if address/size cells aren't found was apparently done for Linux for compatibility with certain buggy Open Firmware implementations, and U-Boot inherited the code. The compliant behavior is to treat a missing #address-cells as 2, and a missing #size-cells as 1 -- never looking anywhere but the immediate parent of the node of interest. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | mpx85xx/fdt: Add cpu-release-addr for all coresMatthew McClintock2010-08-19-7/+8
| | | | | | | | | | | | | | | | We currently do not add a cpu-release-addr for core 0, this is needed when we want to reset core 0 and later restart it from Linux Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/83xx: Fix build issue with ve8313 board due to lbus changesKumar Gala2010-08-19-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We get two build errors: fsl_elbc_nand.c: In function 'fsl_elbc_run_command': fsl_elbc_nand.c:231: error: 'fsl_lbc_t' has no member named 'lsor' make[1]: *** [/work/wd/tmp-ppc/drivers/mtd/nand/fsl_elbc_nand.o] Error 1 and ve8313.c: In function 'initdram': ve8313.c:104: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token ve8313.c:104: error: 'lbc' undeclared (first use in this function) ve8313.c:104: error: (Each undeclared identifier is reported only once ve8313.c:104: error: for each function it appears in.) ve8313.c:104: error: 'immap_t' has no member named 'lbus' make[1]: *** [ve8313.o] Error 1 make: *** [board/ve8313/libve8313.a] Error 2 Due to changes to unifiy local bus struct definitions. Reported-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Fix SRIO LAW setup on corenet_ds boardsLian Minghuan2010-08-19-22/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | In function board_early_init_r(), serdes will not be initialize yet. Thus sRIO was always considered disabled. Move the check for sRIO into misc_init_r() which is called after fsl_serdes_init(). Also, fixed warning associated with gur variable possibly not being used. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Lian Minghuan <B31939@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/8xxx: Fix quad-rank DIMMs support on corenet_ds board.york2010-08-19-2/+18
| | | | | | | | | | | | | | | | | | The board specific parameters associated with quad rank dimms where missing. This fixes it so the board will function if quad rank dimms are placed in it. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Rename Security Engine Job Queue to Job Ring to match docsKumar Gala2010-08-19-11/+11
| | | | | | | | | | | | | | | | Official docs call it the Job Ring not Job Queue for the p4080 security block. Match the docs to reduce confusion. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/8xxx: share PIC defines among 85xx and 86xxKim Phillips2010-08-19-16/+19
|/ | | | | | | | | | fixes breakeage introduced by commit a37c36f4e70bada297f281b0e542539ad43e50f6 "powerpc/8xxx: query feature reporting register for num cores on unknown cpus" Reported-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/masterWolfgang Denk2010-08-18-24/+1116
|\
| * ARM: Update ARM mach-typesSandeep Paulraj2010-08-18-24/+1116
| | | | | | | | | | | | This patch updates the mach-types.h based on the latest linux kernel Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips.Philippe De Muyter2010-08-18-8/+25
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30 256-Mbit 65nm flash chips. After some time :( searching for bugs in our board or soft, we have discovered that those chips have a small but annoying bug, documented in "Numonyx Axcell P33/P30 256-Mbit Specification Update" It states : When customer uses [...] block unlock, the block lock status might be altered inadvertently. Lock status might be set to either 01h or 03h unexpectedly (00h as expected data), which leads to program/erase failure on certain blocks. A working workaround is given, which I have applied and tested with success : Workaround: If the interval between 60h and its subsequent command can be guaranteed within 20us, Option I is recommended, otherwise Option II (involves hardware) should be selected. Option I: The table below lists the detail command sequences: Command Data bus Address bus Remarks Sequence 1 90h Block Address Read Lock Status 2 Read Block Address + 02h (2)(3) (1) 3 60h Block Address (2)(3) (1) Lock/Unlock/RCR Configuration 4 D0h/01h/03h Block Address Notes: (1) Block Address refers to RCR configuration data only when the 60h command sequence is used to set RCR register combined with 03h subsequent command. (2) For the third and fourth command sequences, the Block Address must be the same. (3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h commands should be less than 20us. And here is a log comparison of a simple (destructive) flash test without and with the workaround. diff without-numonyx-workaround.log with-numonyx-workaround.log -U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47) +U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19) CPU: Freescale MCF5484 CPU CLK 200 MHz BUS CLK 100 MHz Board: Macq Electronique ME2060 I2C: ready DRAM: 64 MiB FLASH: 32 MiB In: serial Out: serial Err: serial Net: FEC0, FEC1 -> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 32 MB in 259 Sectors Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922 Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 5 ms, buffer size: 1024 bytes Sector Start Addresses: FE000000 RO FE008000 RO FE010000 RO FE018000 RO FE020000 RO FE040000 RO FE060000 RO FE080000 RO FE0A0000 RO FE0C0000 RO ... FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 RO -> protect off all Un-Protect Flash Bank # 1 ................... done -> erase all Erase Flash Bank # 1 ................... done -> cp.b 1000000 fe000000 2000000 -Copy to Flash... Flash not Erased +Copy to Flash... done -> Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
* cfi_flash: Cleanup flash_print_info()Stefan Roese2010-08-18-24/+27
| | | | | | | | | | | | | | | | | | | | | | | | | This patch does the following: - Extract code to detect if sector is erased into function sector_erased(). - Because of this, we don't have variable declarations inside the sector loop in flash_print_info() - Change "return" to "break" in the "if (ctrlc()) statement: This fixes a problem with the resulting output. Before this patch the output was: Sector Start Addresses: FC000000 FC020000 FC040000 => With this patch it is now: Sector Start Addresses: FC000000 FC020000 FC040000 => Signed-off-by: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
* Fix printing & reading of 16-bit CFI device identifiersPhilippe De Muyter2010-08-18-4/+7
| | | | | | | | | | | | | | Fix reading and printing of CFI flashes 16-bit devices identifiers Nowadays CFI flashes have a 16-bit device identifier. U-boot still print them and read them as if they were only 8-bit wide. Fix that. Before: Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1B After: Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x881B Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
* cfi_flash: flinfo: allow user interrupt in flash print info fnKim Phillips2010-08-18-0/+2
| | | | | | | flashes getting larger, users more impatient. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Stefan Roese <sr@denx.de>
* env_nand: return error when no device is foundMike Frysinger2010-08-13-0/+2
| | | | | | | | | | | | | Currently, if there is an error probing the NAND chip and the env is based in NAND, the readenv() function will use a NULL function pointer and thus jump to address 0. Here I just check for a non-zero value of blocksize as that shouldn't be zero when a valid device is found, but perhaps there is a better way for someone familiar with the NAND internals to suggest. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
* Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk2010-08-12-2/+345
|\
| * Fixed clobbered output of the "help usb" commandSergei Poselenov2010-08-12-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The "usb help" doesn't format the output correctly: => help usb usb - USB sub-system Usage: usb reset - reset (rescan) USB controller usb stop [f] - stop USB [f]=force stop usb tree - show USB device tree usb info [dev] - show available USB devices usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr'usb write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' => With fix below applied, the output is correct: => help usb usb - USB sub-system Usage: usb reset - reset (rescan) USB controller usb stop [f] - stop USB [f]=force stop usb tree - show USB device tree usb info [dev] - show available USB devices usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr' usb write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' => Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
| * AM3517EVM: musb: add usb configAjay Kumar Gupta2010-08-12-0/+38
| | | | | | | | | | | | Enabling USB HOST in defconfig. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
| * musb: am35x: Workaround for fifo read issueAjay Kumar Gupta2010-08-12-0/+38
| | | | | | | | | | | | | | AM35x supports only 32bit read operations so we need to have workaround for 8bit and 16bit read operations. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
| * musb: MSC host support for AM35xAjay Kumar Gupta2010-08-12-1/+216
| | | | | | | | | | | | Tested MSC Host on AM3517EVM. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
| * AM35x: Adding SCM general register definitionsAjay Kumar Gupta2010-08-12-0/+52
| | | | | | | | | | | | | | | | Adding general register structure of system control module (SCM) of AM35x. This would be required to access devconf2 and ip_sw_reset register in musb module. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
* | Blackfin: re-use board data in cpu bannerMike Frysinger2010-08-11-1/+2
| | | | | | | | | | | | | | The bi_cpu field of the board data is already set to the relevant cpu string, so there is no need for us to use the define directly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf548: increase monitor lenMike Frysinger2010-08-11-1/+1
| | | | | | | | | | | | | | Recent features enabled by default require a larger monitor size for the cm-bf548 port, so bump it up a bit. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: shutdown video DMA when booting LinuxMichael Hennerich2010-08-11-0/+38
|/ | | | | | | | | | | In case there is no frame buffer driver present in Linux to hand over the PPI LCD DMA upon boot, the DMA initiated by u-boot to display the splash screen runs unattended. Therefore always stop the video driver in u-boot before starting Linux. If people don't want this behavior, then they can simply stub out the video_stop() function in their board video driver. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* disk/part.c: 'usb storage' avoiding overflow when output capacitySergei Trofimovich2010-08-10-5/+23
| | | | | | | | | | | | | | | Before: Marvell>> usb storage Device 0: Vendor: StoreJet Rev: Prod: Transcend Type: Hard Disk Capacity: 28759.9 MB = 28.0 GB (488397168 x 512) After: Marvell>> usb storage Device 0: Vendor: StoreJet Rev: Prod: Transcend Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-08-10-136/+2339
|\
| * Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-08-10-2/+2
| |\
| | * MX51EVK: fix return value of get_timer_maskedLi Haibo2010-08-10-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | get_timer_masked() should return current timestamp, not current ticks from hardware register. Tested on one custom board with NAND flash. Without this patch, NAND write always TIMEOUT because get_timer(0) return a big value. This patch applies for u-boot-2010.06 Signed-off-by: Li Haibo <hbli@sinocastel.com>
| | * fix cmd_mmc.c, line 136 missing "Reinhard Meyer2010-08-10-1/+1
| | | | | | | | | | | | | | | | | | Remove warning for missing " at the end of line 136 Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | orion5x: allow overriding default mappings windowsAlbert Aribaud2010-08-10-41/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Turn all ORION5X_DEF{ADR,SZ}_xxx macros into ORION5X_{ADR,SZ}_xxx and allow defining them from board code to override defaults. This is particularly useful for defining board-specific FLASH address and size in board header file rather than having to tweak orion5x code. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| * | Merge branch 'master' of git://git.denx.de/u-boot-marvellWolfgang Denk2010-08-10-13/+247
| |\ \
| | * | Kirkwood: openrd_base: Added SATA supportPrafulla Wadaskar2010-08-08-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables mvsata driver and related filesystem support. The patch is tested for ide reset and ext2ls operation for a disk drive connected on SATA port0. This patch depends upon the patche-series http://lists.denx.de/pipermail/u-boot/2010-August/074908.html Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| | * | cmd_ide: add support for KirkwoodPrafulla Wadaskar2010-08-08-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Added MVSATAC definitions to Kirkwood. Added support for Kirkwood in cmd_ide. Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| | * | edminiv2: add mvsata_ide and cmd_ide supportAlbert Aribaud2010-08-08-1/+33
| | | | | | | | | | | | | | | | | | | | | | | | Add mvsata_ide and cmd_ide configuration in edminiv2 config Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| | * | cmd_ide: add support for orion5xAlbert Aribaud2010-08-08-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add MVSATAHC definitions to orion5x. Add support for orion5x in cmd_ide. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| | * | ide: add mvsata_ide driverAlbert Aribaud2010-08-08-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver only provides initialization code; actual driving is done by cmd_ide.c using the ATA compatibility mode of the Marvell SATAHC controller. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| | * | ide: reorder object files alphabeticallyAlbert Aribaud2010-08-08-3/+3
| | | | | | | | | | | | | | | | Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
generated by cgit v1.1 at 2024-11-09 20:51:03 +0000