summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
| * net/fm: Remove unused code of FMan QMIHou Zhiqiang2016-08-22-3/+0
| | | | | | | | | | | | | | | | The QMan is not used in FMan IM mode, so no QMI enqueue or QMI dequeue are performed. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: davinci_emac: Invalidate only the received portion of a bufferkarl beldan2016-08-22-5/+5
| | | | | | | | | | | | | | | | | | | | ATM when receiving a packet the whole buffer is invalidated, this change optimizes this behaviour. Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
| * net: davinci_emac: Round up top tx buffer boundaries for dcache opskarl beldan2016-08-22-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | check_cache_range() warns that the top boundaries are not properly aligned when flushing or invalidating the buffers and make these operations fail. This gets rid of the remaining warnings: CACHE: Misaligned operation at range Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
| * net: davinci_emac: Remove useless dcache ops on descriptorskarl beldan2016-08-22-28/+0
| | | | | | | | | | | | | | | | | | | | | | | | ATM the rx and tx descriptors are handled as cached memory while they lie in a dedicated RAM of the SoCs, which is an uncached area. Removing the said dcache ops, while optimizing the logic and clarifying the code, also gets rid of most of the check_cache_range() incurred warnings: CACHE: Misaligned operation at range Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Simplify rpc_add_credentials()Joe Hershberger2016-08-22-16/+3
| | | | | | | | | | | | | | We use an empty hostname, so remove all the "processing" of the known-to-be-empty hostname and just write 0's where needed. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Use the tx buffer to construct rpc msgsJoe Hershberger2016-08-22-43/+45
| | | | | | | | | | | | | | | | | | Instead of always allocating a huge temporary buffer on the stack and then memcpy()ing the result into the transmit buffer, simply figure out where in the transmit buffer the bytes will belong and write them there directly as each message is built. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Move some prints to debug statementsJoe Hershberger2016-08-22-21/+22
| | | | | | | | | | | | | | | | Much of the information is verbose and derived directly from the environment. Only output in debug mode. This also saves about 300 bytes from the code size. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Use consistent names for the rpc_pktJoe Hershberger2016-08-22-17/+17
| | | | | | | | | | | | | | Use the same name throughout the nfs code and use the same member of the union to avoid casts. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Correct a commentJoe Hershberger2016-08-22-1/+1
| | | | | | | | | | | | The buffer is of 32-bit elements, not bytes. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Consolidate handling of NFSv3 attributesJoe Hershberger2016-08-22-92/+59
| | | | | | | | | | | | | | Instead of repeating the same large snippet for dealing with attributes it should be shared with a helper function. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Fix lines that are too longJoe Hershberger2016-08-22-3/+6
| | | | | | | | | | | | Fix complaints from checkpatch.pl. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Correct the reply data buffer sizeJoe Hershberger2016-08-22-1/+1
| | | | | | | | | | | | | | | | | | | | The type of the buffer is uint32_t, but the parameter used to size it is referring to bytes. Divide by the size of the array elements. Strictly speaking, this shouldn't be needed at all... It could just be 1 just like the request. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Share the file handle buffer for v2 / v3Joe Hershberger2016-08-22-7/+5
| | | | | | | | | | | | | | The v3 handles can be larger than v2, but that doesn't mean we need a separate buffer. Reuse the same (larger) buffer for both. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: NFS: Add NFSv3 supportGuillaume GARDET2016-08-22-47/+242
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables NFSv3 support. If NFSv2 is available use it as usual. If NFSv2 is not available, but NFSv3 is available, use NFSv3. If NFSv2 and NFSv3 are not available, print an error message since NFSv4 is not supported. Tested on iMX6 sabrelite with 4 Linux NFS servers: * NFSv2 + NFSv3 + NFSv4 server: use NFSv2 protocol * NFSv2 + NFSv3 server: use NFSv2 protocol * NFSv3 + NFSv4 server: use NFSv3 protocol * NFSv3 server: use NFSv3 protocol Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@konsulko.com> Cc: joe.hershberger@ni.com Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Remove unused defineJoe Hershberger2016-08-22-2/+0
| | | | | | | | | | | | Unreferenced, so remove the noise. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: nfs: Remove separate buffer for default nameJoe Hershberger2016-08-22-3/+1
| | | | | | | | | | | | | | | | There is no reason to store the default filename in a separate buffer only to immediately copy it to the main name buffer. Just write it there directly and remove the other buffer. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: Stop including NFS overhead in defragment maxJoe Hershberger2016-08-22-9/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | At least on bfin, this "specimen" is actually allocated in the BSS and wastes lots of memory in already tight memory conditions. Also, with the introduction of NFSv3 support, this waste got substantially larger. Just remove it. If a board needs a specific different defragment size, that board can override this setting. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* | Prepare v2016.09-rc2Tom Rini2016-08-22-1/+1
| | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* | fs-test.sh: Correct check_md5() test with newlinesTom Rini2016-08-22-1/+1
|/ | | | | | | | | | The fs-test.sh script expected there to be a \n\r style newline at the end of the output. This is no longer the case, so use 'tr' to remove the \r that we get. Fixes: (c5917b4b054d "dm: serial-uclass: Move a carriage return before a line feed") Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini2016-08-20-221/+11604
|\ | | | | | | | | [trini: Drop CMD_BOOTI as it's now on by default on ARM64] Signed-off-by: Tom Rini <trini@konsulko.com>
| * ARM: rmobile: r8a7795: Add MMU layoutNobuhiro Iwamatsu2016-08-17-1/+31
| | | | | | | | | | | | This add MMU layout for R8A7795 of Renesas ARM64 SoC. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: salvator-x: Update defconfigNobuhiro Iwamatsu2016-08-17-1/+9
| | | | | | | | | | | | This moves some config from config files. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Remove duplicate configs by Kconfig in rcar-gen3-common.hNobuhiro Iwamatsu2016-08-17-7/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit remove dupilicate following configs from rcar-gen3-common.h. - CONFIG_CMD_BOOTZ - CONFIG_BOOTDELAY - CONFIG_CMD_EDITENV - CONFIG_CMD_SAVEENV - CONFIG_CMD_MEMORY - CONFIG_CMD_RUN - CONFIG_CMD_LOADS Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: lager: Move rcar-gen2-common to rcar-commonNobuhiro Iwamatsu2016-08-17-1/+1
| | | | | | | | | | | | | | To common use of rcar-gen2-common directory in the R-Car SoCs, and change from rcar-gen2-common to rcar-common. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Update defconfigNobuhiro Iwamatsu2016-08-17-116/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This updated defconfig following boards: - Alt - Gose - Koelsh - Lager - Porter - Silk - Stout - Blanche Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Fix HDMI output for BLANCHE boardmasakazu.mochizuki.wd@hitachi.com2016-08-17-0/+30
| | | | | | | | | | | | | | This commit fixes HDMI output for BLANCHE board Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Add BLANCHE board supportmasakazu.mochizuki.wd@hitachi.com2016-08-17-47/+5006
| | | | | | | | | | | | | | | | | | | | BLANCHE is development board based on R-Car V2H SoC (R8A7792) This commit supports the following periherals: - SCIF, Ethernet, QSPI, MMC Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * mmc: rmobile: add a compiler barrierYannick Gicquel2016-08-17-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Building w/ GCC v5.2, the SD card access is broken due to invalid data in the response command reconstructed at the end of sh_sdhci_get_response(). Add a memory barrier between the two main steps of this function to ensure the resp[] table content is consistent before bits reordering. This fix has been tested Ok on Porter board rev1.0 using v2016.03 release. Signed-off-by: Yannick Gicquel <yannick.gicquel@iot.bzh>
| * ARM: rmobile: rcar-common: Fix warning of type differenceNobuhiro Iwamatsu2016-08-17-2/+4
| | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Add support salvator-x boardNobuhiro Iwamatsu2016-08-17-0/+329
| | | | | | | | | | | | | | | | Salvator-x is an entry level development board based on R-Car H3 SoC (R8A7795). This commit supports SCIF only. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Add support R8A7795Nobuhiro Iwamatsu2016-08-17-0/+5877
| | | | | | | | | | | | | | | | | | Renesas R8A7795 is CPU with Cortex-a57. This supports the basic register definition and GPIO and framework of PFC. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Add support R-Car Generation 3Nobuhiro Iwamatsu2016-08-17-1/+198
| | | | | | | | | | | | | | This adds supporting R-Car Generation 3 (Gen3) as Renesas ARM64 SoC. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Move rcar-gen2-common to rcar-commonNobuhiro Iwamatsu2016-08-17-7/+7
| | | | | | | | | | | | | | To common use of rcar-gen2-common directory in the R-Car SoCs, and change from rcar-gen2-common to rcar-common. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Create R-Car 32bit (Gen1 and Gen2) for KconfigNobuhiro Iwamatsu2016-08-17-82/+96
| | | | | | | | | | | | This creates Kconfig of R-Car 32bit for Kconfig of R-Car 64bit (Gen3). Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * serial: sh: Add support R8A7795Hiroyuki Yokoyama2016-08-17-1/+2
| | | | | | | | | | | | | | This can be used in the same way as other R-CAR serial setting. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * MAINTAINERS: Add maintainer entry of RMOBILENobuhiro Iwamatsu2016-08-17-0/+6
| | | | | | | | | | | | Add MAINTAINERS entry. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: Rmobile: Rename CONFIG_RMOBILE to CONFIG_ARCH_RMOBILENobuhiro Iwamatsu2016-08-17-67/+69
| | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Move SoC headers to mach-rmobile/include/machNobuhiro Iwamatsu2016-08-17-0/+0
| | | | | | | | | | | | Move form arch/arm/include/asm/arch-rmobile/ to arch/arm/mach-rmobile/include/mach/. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * ARM: rmobile: Move SoC sources to mach-rmobileNobuhiro Iwamatsu2016-08-17-2/+3
| | | | | | | | | | | | Move from arch/arm/cpu/armv7/rmobile/ to arch/arm/mach-rmobile/. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | pinctrl: fix typos in comment blocks of pinconfig_post_bind()Masahiro Yamada2016-08-20-2/+2
| | | | | | | | | | | | '-' is never used in function names. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | efi_loader: Fix relocations above 64kb image sizeAlexander Graf2016-08-20-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | We were truncating the image offset within the target image to 16 bits which again meant that we were potentially overwriting random memory in the lower 16 bits of the image. This patch casts the offset to a more reasonable 32bits. With this applied, I can successfully see Shell.efi assert because it can't find a protocol it expects to be available. Signed-off-by: Alexander Graf <agraf@suse.de>
* | Makefile: Remove tags file on mrproperVignesh R2016-08-20-1/+1
| | | | | | | | | | | | | | | | make tags creates a symbolic link called tags to ctags. Remove this file on make mrproper or make distclean. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | tools/env: soften warning about erase block alignmentAndreas Fenkart2016-08-20-1/+1
| | | | | | | | | | | | | | | | | | addon 183923d3e MMC/SATA have no erase blocks, only blocks. Hence the warning about erase block alignment might be confusing in such environment. Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | tools/env: return with error if redundant environments have unequal sizeAndreas Fenkart2016-08-20-3/+2
| | | | | | | | | | | | | | | | | | | | | | For double buffering to work, the target buffer must always be big enough to hold all data. This can only be ensured if buffers are of equal size, otherwise one must be smaller and we risk data loss when copying from the bigger to the smaller buffer. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: OMAP4+: vcores: Remove duplicated codeLokesh Vutla2016-08-20-52/+10
| | | | | | | | | | | | | | | | | | | | There is no reason to duplicate code for DRA7xx platforms as there can be Rail grouping. The maximum voltage detection algorithm can still be run on other platforms with no Rail grouping and does not harm as it gives the same result. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: OMAP5+: vcores: Drop unnecessary #ifndefsLokesh Vutla2016-08-20-6/+3
| | | | | | | | | | | | | | | | | | | | gpio_en field is introduced to detect if pmic is controlled by GPIO. Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms and remove the #ifndefs. Reviewed-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | test/py: match prompt only at line boundariesStephen Warren2016-08-20-3/+3
| | | | | | | | | | | | | | | | | | | | | | This prevents capture of command output from terminating early on boards that use a simple prompt (e.g. "=> ") that appears in the middle of command output (e.g. crc32's "... ==> 2fa737e0"). Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
* | common: cli_readline: Improve command line editingJames Byrne2016-08-20-31/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This improves the cread_line() function so that it will correctly process the 'Home', 'End', 'Delete' and arrow key escape sequences produced by various terminal emulators. This makes command line editing a more pleasant experience. The previous code only supported the cursor keys and the 'Home' key, and only for certain terminal emulator configurations. This adds support for the 'End and 'Delete' keys, and recognises a wider range of escape sequences. For example, the left arrow key can be 'ESC O D' instead of 'ESC [ D', and the 'Home' key can be 'ESC [ H', 'ESC O H', 'ESC 1 ~' or 'ESC 7 ~', depending on what terminal emulator you use and how it is configured. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Changes for v2 - Explicitly initialize variable to avoid spurious compiler warning. Changes for v3 - Remove unnecessary setting of 'act' to ESC_REJECT (now its default value).
* | fastboot: move to KconfigSteve Rae2016-08-20-16/+16
| | | | | | | | | | | | | | - move bcm23550_w1d to Kconfig - move bcm28155_ap to Kconfig Signed-off-by: Steve Rae <steve.rae@raedomain.com>
* | fastboot: implement KconfigSteve Rae2016-08-20-0/+67
| | | | | | | | | | | | implement Kconfig for the 'fastboot' feature set Signed-off-by: Steve Rae <steve.rae@raedomain.com>
generated by cgit v1.1 at 2024-11-07 18:43:38 +0000