summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
| * | net/designware: Try configuring phy on each dw_eth_initVipin Kumar2012-04-04-21/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Phy autonegotiation works only when the ethernet cable is plugged in. Since the phy was configured only at the init time, a plugged in cable was necessary to initialize the phy properly. This patch keeps a flag to check if the phy initialization has succeeded, and calls configure_phy routine at every init if this flag reports otherwise. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
| * | net/designware: Consecutive writes must have delayArmando Visconti2012-04-04-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch solves a TX/RX problem which happens at 10Mbps, due to the fact that we are not respecting 4 cyles of the phy_clk (2.5MHz) between two consecutive writes on the same register. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
| * | net/designware: Phy address fixVipin KUMAR2012-04-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The code assumes the phy address to be > 0, which is not true, the phy address can be in the range 0-31. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
| * | net/designware: Fix the max frame length sizeVipin KUMAR2012-04-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | The max frame length for normal descriptor can be 0x7FF i.e 2047. It was wrongly specified as 2048. Currently, the max descriptor length is around 1500, so redefining the mask to 1600 Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
| * | net/designware: Fix to restore hw mac addressVipin KUMAR2012-04-04-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | The network controller mac resets hardware address stored in MAC_HI and MAC_LO registers if mac is resetted. So, hw mac address needs to be restored in case mac is explicitly resetted from driver. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
| * | microblaze: Wire up LL_TEMAC driver initializationStephan Linz2012-04-04-0/+36
| | | | | | | | | | | | | | | | | | | | | Initialize ll_temac driver. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
| * | microblaze: Add faked LL_TEMAC driver configurationStephan Linz2012-04-04-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Expand the specific configuration for the microblaze-generic board in xparameters.h with a faked setup to enable the LL_TEMAC driver. Note: From now the microblaze-generic board is no longer a valid board configuration for a real piece of hardware. Rather than, we use the file config.mk and xparameters.h as a faked board configuration to force the compilation of all potential driver code for Microblaze systems. Signed-off-by: Stephan Linz <linz@li-pro.net>
| * | microblaze: Enable several ethernet driver compilationStephan Linz2012-04-04-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | U-Boot's multipple network supports enables to use several ethernet drivers but microblaze-generic platform config file select only one driver. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
| * | net: ll_temac: Add LL TEMAC driver to u-bootStephan Linz2012-04-04-0/+1872
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xilinx LocalLink Tri-Mode Ether MAC driver can be used by Xilinx Microblaze or Xilinx ppc405/440 in SDMA and FIFO mode. DCR or XPS bus can be used. The driver uses and requires MII and PHYLIB. CP: 4 warnings: 'Use of volatile is usually wrong' I won't fix this, because it depends on the network driver subsystem. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
| * | Update net subsystem maintainer in doc/git-mailrcJoe Hershberger2012-04-03-1/+2
| | | | | | | | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com>
| * | net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall backEric Miao2012-04-03-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ignore the return value of eth_getenv_enetaddr_by_index(), and if it fails, fall back to use dev->enetaddr, which could be filled up by the ethernet device driver: With the current code, introduced with below commit, eth_write_hwaddr() will fail immediately if there is no eth<n>addr in the environment variables. However, e.g. for an overo based product that uses the SMSC911x ethernet chip (with the MAC address set via EEPROM connected to the SMSC911x chip), the MAC address is still OK. On mx28 boards that are depending on the OCOTP bits to set the MAC address (like the Denx m28 board), the OCOTP bits should be used instead of failing on the environment variables. Actually, this was the original behavior, and was later changed by commit 7616e7850804c7c69e0a22c179dfcba9e8f3f587. Signed-off-by: Eric Miao <eric.miao@linaro.org> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Stefan Roese <sr@denx.de> CC: Eric Miao <eric.miao@linaro.org> CC: Wolfgang Denk <wd@denx.de> CC: Philip Balister <philip@balister.org> CC: Zach Sadecki <zach@itwatchdogs.com>
| * | mvgbe: remove warning for unused methodsStefan Bigler2012-04-03-0/+2
| |/ | | | | | | | | | | | | | | | | | | Some baords may use the GBE interface but they have no phy connected to the interface and a direct MAC/MAC interface. For them we need to get rid of compiler warnings. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-onenandWolfgang Denk2012-04-09-23/+86
|\ \ | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-onenand: onenand: samsung: Enable OneNAND support at Samsung's Exynos4210 onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB() onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210 onenand:samsung Target dependent OneNAND chip probe function
| * | onenand: samsung: Enable OneNAND support at Samsung's Exynos4210Lukasz Majewski2012-04-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Enable OneNAND support for Exynos4210 (C210 universal). Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * | onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()Lukasz Majewski2012-04-04-16/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This replacement causes 4KB page size devices to work properly with u-boot. The old ONENAND_IS_MLC() behavior has been preserved by explicit setting of ONENAND_HAS_4KB_PAGE for those devices. This change makes the onenand_base.c file more resembling the respective kernel sources. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> --- Test HW: - Samsung S5PC110 GONI - Samsung S5PC210 Universal
| * | onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210Lukasz Majewski2012-04-04-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Separate callback for probing OneNAND memory chip. Tested at: Samsung S5PC110 GONI Samsung Exynos4210 (S5PC210 Universal) Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * | onenand:samsung Target dependent OneNAND chip probe functionLukasz Majewski2012-04-04-7/+49
| |/ | | | | | | | | | | | | | | | | | | Separate callback for probing OneNAND memory chip. If no special function is defined, default implementation will be used. This approach gives more flexibility for OneNAND device probing. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-niosWolfgang Denk2012-04-09-1/+33
|\ \ | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-nios: nios2 - adjust gbl data off to account for bd_info nios2: implement get_ticks and get_tbclk nios2: add flush_dcache_range function
| * | nios2 - adjust gbl data off to account for bd_infoAlex Hornung2012-02-24-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Adjust the GBL_DATA_OFFSET to account for the fact that we'll be using the space between that offset and the start of the malloc region to allocate both a gd structure and a board info structure. * This fixes a memory corruption bug due to overlap of the malloc region and the bd_info structure. Signed-off-by: Alex Hornung <alex@alexhornung.com> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
| * | nios2: implement get_ticks and get_tbclkAlex Hornung2012-02-23-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | * Copy over Blackfin's get_ticks and get_tbclk - they work just fine on Nios2. Signed-off-by: Alex Hornung <alex@alexhornung.com> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
| * | nios2: add flush_dcache_range functionStefan Kristiansson2012-02-23-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | exposes functionality to flush dcache according to the common.h API Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
* | | Merge branch 'master' of git://git.denx.de/u-boot-x86Wolfgang Denk2012-04-09-5/+0
|\ \ \ | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-x86: x86: Remove dead code in eNET
| * | | x86: Remove dead code in eNETSimon Glass2012-04-01-5/+0
| | |/ | |/| | | | | | | | | | | | | | | | This avoids a compiler warning about unused variables. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-By: Graeme Russ <graeme.russ@gmail.com>
* | | LMB: Fix undefined lmb_reserve() on non-lmb platformsMarek Vasut2012-04-09-0/+1
|/ / | | | | | | | | | | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
* | Prepare v2012.04-rc1Wolfgang Denk2012-03-31-3/+3
| | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | net/altera_tse: use flush_dcache_range instead of flush_dcacheStefan Kristiansson2012-03-30-3/+6
| | | | | | | | | | | | | | | | | | | | flush_dcache is not declared in the common.h API, flush_dcache_range however is Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
* | net/ethoc: use flush_dcache_range instead of flush_dcacheStefan Kristiansson2012-03-30-3/+3
| | | | | | | | | | | | | | | | | | | | flush_dcache is not declared in the common.h API, flush_dcache_range however is Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
* | Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk2012-03-30-7/+116
|\ \ | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-usb: Enable high speed support for USB device framework and usbtty
| * | Enable high speed support for USB device framework and usbttyVipin KUMAR2012-03-28-7/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the support for high speed in usb device framework and usbtty driver. This feature has been kept within a macro CONFIG_USBD_HS, so the board configuration files have to define this macro to enable high speed support. Along with that specific peripheral drivers also need to define a function to let the framework know that the enumeration has happened at high speed. This function prototype is "int is_usbd_high_speed(void)" Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
* | | RAMDISK: Fix unused variable issue caused by raw rd supportMarek Vasut2012-03-30-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | image.c: In function ‘boot_get_ramdisk’: image.c:800:8: warning: unused variable ‘end’ [-Wunused-variable] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* | | BOOT: Add RAW ramdisk support to bootzMarek Vasut2012-03-30-5/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch allows loading RAW ramdisk via bootz command. The raw ramdisk is loaded only in case it's size is specified: bootz <kernel addr> <ramdisk addr>:<ramdisk size> <fdt addr> For example: bootz 0x42000000 0x43000000:0x12345 0x44000000 Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
* | | BOOT: Add "bootz" command to boot Linux zImage on ARMMarek Vasut2012-03-30-9/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This command boots Linux zImage from where the zImage is loaded to. Passing initrd and fdt is supported. Tested on i.MX28 based DENX M28EVK Tested on PXA270 based Voipac PXA270. NOTE: This currently only supports ARM, but other architectures can be easily added by defining bootz_setup(). Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com, Cc: Simon Glass <sjg@chromium.org>, Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
* | | mx28evk: fix build errorAnatolij Gustschin2012-03-30-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix: drivers/mmc/libmmc.o: In function `mxsmmc_send_cmd': /home/ag/git/u-boot/drivers/mmc/mxsmmc.c:210: undefined reference to `mxs_dma_desc_append' /home/ag/git/u-boot/drivers/mmc/mxsmmc.c:211: undefined reference to `mxs_dma_go' drivers/mmc/libmmc.o: In function `mxsmmc_initialize': /home/ag/git/u-boot/drivers/mmc/mxsmmc.c:306: undefined reference to `mxs_dma_desc_alloc' Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* | | pci: declare pciauto functions in headerLinus Walleij2012-03-30-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The FSL PCI driver uses local prototypes for pciauto_[pre|post]scan_setup_bridge(), this does not seem right, so move them to the <pci.h> file. Fixed a small extern declaration too, this is harmless but distracts the view since all other prototypes are explicitly external. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | pci: get rid of local prototypesLinus Walleij2012-03-30-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | two boards were redeclaring pciauto_region_allocate() in their local scope for no obvious reason, the function is in <pci.h> anyway, this is probably just copying artifacts and old cruft. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | Add support for loading and saving the environment to a FAT partitionMaximilian Schwerin2012-03-30-1/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following must be defined: CONFIG_ENV_IS_IN_FAT Enable this saving environment to FAT. FAT_ENV_INTERFACE Interface the FAT resides on (e.g. mmc). FAT_ENV_DEVICE The interface device number (e.g. 0 for mmc0) FAT_ENV_PART The device part (e.g. 1 for mmc0:1) FAT_ENV_FILE The filename of the environment file. Author: Maximilian Schwerin <mvs@tigris.de> Removed dead DEBUG comment. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | MAKEALL: Add -m/-M option to determine maintainersMarek Vasut2012-03-30-3/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The -m option tries to find the board in MAINTAINERS file and figure out the email. The -M option lists boards including their maintainers emails and all affiliated emails. There are multiple strategies used to retrieve these emails: 1) Check board/<boardname> with git log and use three most recent emails 2) Check board/<boardname> with git log and use three most used emails 3) Try finding board in MAINTAINERS file and retrieve all emails from there The result is then sorted and unique results are retrieved and reported. For -m option, only strategy 3) is used. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* | | cmd_log: print log->v2.con value in the "log info" commandHeiko Schocher2012-03-30-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | print in the "log info" command, if "log_version = 2" also the value from "log->v2.con". Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* | | command, log: Coding Style cleanupHeiko Schocher2012-03-30-45/+51
| | | | | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* | | command, log: print with "log show" a full logbufferHeiko Schocher2012-03-30-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the logbuffer contains LOGBUFF_LEN chars, they never got printed with the "log show" command, because chars get printed with the following for loop: for (i = 0; i < (size & LOGBUFF_MASK); i++) { with size = LOGBUFF_LEN and LOGBUFF_MASK = (LOGBUFF_LEN-1) for loop never executed ... Fix this. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Fixed merge conflict. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | drivers/mmc/mmc.c: Fix build warningAnatolij Gustschin2012-03-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix: mmc.c: In function 'mmc_bounce_buffer_start': mmc.c:132:13: warning: no return statement in function returning non-void [-Wreturn-type] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* | | drivers/mmc/tegra2_mmc.c: fix GCC 4.6 warningAnatolij Gustschin2012-03-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix: tegra2_mmc.c: In function 'mmc_send_cmd': tegra2_mmc.c:230:3: warning: 'mask' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Doug Anderson <dianders@chromium.org> Cc: Tom Warren <twarren@nvidia.com>
* | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2012-03-30-132/+210
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of /home/wd/git/u-boot/custodians: lzma: fix printf warnings Remove CONFIG_SYS_EXTBDINFO from snapper9260.h cmd_pxe.c: fix strict-aliasing warnings net: smc91111: use mdelay() doc: Fix some typos in different files disk/part.c: Fix device enumeration through API mkenvimage: Really set the redundant byte when applicable mkenvimage: Don't try to detect comments in the input file mkenvimage: Use mmap() when reading from a regular file mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-" mkenvimage: More error handling mkenvimage: Correct an include and add a missing one mkenvimage: correct and clarify comments and error messages MAKEALL: display SPL size if present ARMV7/Vexpress: add missing get_ticks() and get_tbclk() mkenvimage: fix usage message cmd_fat: add FAT write command fs/fat/fat_write.c: Fix GCC 4.6 warnings FAT write: Fix compile errors
| * \ \ Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk2012-03-30-132/+210
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'agust@denx.de' of git://git.denx.de/u-boot-staging: lzma: fix printf warnings Remove CONFIG_SYS_EXTBDINFO from snapper9260.h cmd_pxe.c: fix strict-aliasing warnings net: smc91111: use mdelay() doc: Fix some typos in different files disk/part.c: Fix device enumeration through API mkenvimage: Really set the redundant byte when applicable mkenvimage: Don't try to detect comments in the input file mkenvimage: Use mmap() when reading from a regular file mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-" mkenvimage: More error handling mkenvimage: Correct an include and add a missing one mkenvimage: correct and clarify comments and error messages MAKEALL: display SPL size if present ARMV7/Vexpress: add missing get_ticks() and get_tbclk() mkenvimage: fix usage message cmd_fat: add FAT write command fs/fat/fat_write.c: Fix GCC 4.6 warnings FAT write: Fix compile errors
| | * | | lzma: fix printf warningsMike Frysinger2012-03-28-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix size_t printf format warnings: LzmaTools.c: In function 'lzmaBuffToBuffDecompress': LzmaTools.c:110:5: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'SizeT' LzmaTools.c:111:5: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'SizeT' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| | * | | Remove CONFIG_SYS_EXTBDINFO from snapper9260.hSimon Glass2012-03-27-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This feature is not available on ARM, so it is an error to define it. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | | cmd_pxe.c: fix strict-aliasing warningsJason Hobbs2012-03-27-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without this patch, some versions of gcc (at least ELDK 4.2) complain about dereferencing type-punned pointers. Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com> Cc: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marex@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
| | * | | net: smc91111: use mdelay()Mike Frysinger2012-03-27-13/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We've already got a mdelay() func in common code, so use that instead. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| | * | | doc: Fix some typos in different filesThomas Weber2012-03-27-26/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | adresses/addresses alernate/alternate asssuming/assuming calcualted/calculated enviroment/environment evalutation/evaluation falsh/flash labled/labeled paramaters/parameters Signed-off-by: Thomas Weber <thomas@tomweber.eu> Acked-by: Anatolij Gustschin <agust@denx.de>
| | * | | disk/part.c: Fix device enumeration through APITim Kientzle2012-03-27-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch below fixes device enumeration through the U-Boot API. Device enumeration crashes when the system in question doesn't have any RAM mapped to address zero (I discovered this on a BeagleBone board), since the enumeration calls get_dev with a NULL ifname sometimes which then gets passed down to strncmp(). This fix simply ensures that get_dev returns NULL when invoked with a NULL ifname. Signed-off-by: Tim Kientzle <kientzle@freebsd.org> Signed-off-by: Anatolij Gustschin <agust@denx.de>
generated by cgit v1.1 at 2024-11-08 06:56:47 +0000