summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ehci-omap: driver for EHCI host on OMAP3Ilya Yanok2012-02-12-101/+161
| | | | | | | Taken from Beagle code. Tested on mcx board (AM3517-based). Signed-off-by: Ilya Yanok <yanok@emcraft.com> Tested-by: Stefano Babic <sbabic@denx.de>
* usb: ulpi: Add omap-ulpi-view port supportGovindraj.R2012-02-12-0/+140
| | | | | | | | | | | | | | | | | | | Based on discussion from this thread [1]. Adding omap-view port that helps us in using the generic ulpi framework for any ulpi phy ops using the INSNREG05_ULPI viewport reg available on omap platform. Currently ehci ports are available on omap3/4 platforms so enable the same for beagle and panda, patch is tested on the same boards. Thanks to Igor Grinberg <grinberg@compulab.co.il> for reviewing the omap-ehci patches and suggesting this approach. [1]: http://www.mail-archive.com/u-boot@lists.denx.de/msg76076.html Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* usb: ulpi: Extend the existing ulpi framework.Govindraj.R2012-02-12-62/+84
| | | | | | | | | | Extend the existing ulpi viewport framework to pass the port number information for any ulpi ops. Fix the usage of ulpi api's accordingly. Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* ARM: Convert spear3xx and spear6xx boards to boards.cfgAmit Virdi2012-02-12-8/+4
| | | | | Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de>
* SMDK5250: Add ethernet supportChander Kashyap2012-02-12-2/+103
| | | | | | | | | This patch enable support for SMC911X based ethernet device. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* EXYNOS: SMDK5250: Add MMC SPL supportChander Kashyap2012-02-12-0/+201
| | | | | | | This patch adds support for MMC SPL booting. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* EXYNOS: Add SMDK5250 board supportChander Kashyap2012-02-12-0/+1648
| | | | | | | SMDK5250 board is based on Samsungs EXYNOS5250 SoC. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* ARM: EXYNOS: Add support for Exynos5 based SoCsChander Kashyap2012-02-12-12/+854
| | | | | | | | Samsung's ARM Cortex-A15 based SoCs are known as Exynos5 series of SoCs. This patch adds the support for Exynos5. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos: Clock.c: Use CONFIG_SYS_CLK_FREQ macroChander Kashyap2012-02-12-5/+3
| | | | | | | | | CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4) architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ to make it generic for exynos architecture. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* TRATS: set gpio of UART correctlyMinkyu Kang2012-02-12-11/+7
| | | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
* TRATS: use the generic watchdog timerMinkyu Kang2012-02-12-10/+1
| | | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: HeungJun, Kim <riverful.kim@samsung.com>
* S5P: support generic watchdog timerMinkyu Kang2012-02-12-1/+124
| | | | | | | | This patch adds support the generic watchdog timer for s5pc1xx and exynos4 Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: HeungJun, Kim <riverful.kim@samsung.com>
* ORIGEN: remove duplicated MACH_TYPE defineMinkyu Kang2012-02-12-2/+0
| | | | | | | | Since MACH_TYPE_ORIGEN is updated on mach-types, remove the MACH_TYPE_ORIGEN on config file. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
* ARMV7: Exynos4: Add support for TRATS boardHeungJun, Kim2012-02-12-0/+1280
| | | | | | | | This patch adds support for Samsung TRATS board Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* ARMV7: Exynos4: Add supoort power for Exynos4HeungJun, Kim2012-02-12-0/+231
| | | | | | | | This patch adds power.h and SAMSUNG_BASE() macro for using Exynos4 power. Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* ARMV7: Exynos4: Add watchdog.h for Exynos4HeungJun, Kim2012-02-12-0/+53
| | | | | | | | This patch add watchdog.h for Exynos4 Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Origen: Select SCLKMPLL as FIMD0 parent clockChander Kashyap2012-02-12-0/+17
| | | | | Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos: Fix ARM Clock frequency calculationChander Kashyap2012-02-12-6/+9
| | | | | | | | | | Earliar ARM clock frequency was calculated by: MOUTAPLL/(DIVAPLL + 1) which is actually returning SCLKAPLL. It is fixed by calculating it as follows: ARMCLK=MOUTCORE / (DIVCORE + 1) / (DIVCORE2 + 1) Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos: PWM: Add TCMPB3 field in pwm structureChander Kashyap2012-02-12-1/+1
| | | | | | | Add TCMPB3 field in pwm structure, earliar this was res1. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* arm/km: checkpatch cleanupHolger Brunck2012-02-12-12/+11
| | | | | | | Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Heiko Schocher <hs@denx.de>
* arm/km: speed up i2c access for keymile boardsHolger Brunck2012-02-12-1/+1
| | | | | | | | | | | | We don't need 3us delay for our i2c bus. Decrease it to 1us. It would also be possible to use 100ns in the future, but currently kirkwood has no ndelay implementation. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* bugfix: all Marvell specific build fails due to undefined reference to ↵Prafulla Wadaskar2012-02-12-0/+72
| | | | | | | | | | | | | | | | `get_ticks' after http://patchwork.ozlabs.org/patch/136415/ was applied. All Marvell build fails with below error common/libcommon.o: In function `cread_line': /home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_ticks' /home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_tbclk' /home/uboot/src/u-boot-arm/common/main.c:720: undefined reference to `get_ticks' The same is fixed for Kirkwood, ARMADA100, pantheon and orion5x SoCs Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* kirkwood: add support for D-Link DNS-325Stefan2012-02-12-0/+646
| | | | | | | | This patch adds support for D-Link DNS-325 ShareCenter NAS. Signed-off-by: Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net> Cc: prafulla@marvell.com Cc: albert.u.boot@aribaud.net
* arm, arm-kirkwood: disable l2c before linux bootMichael Walle2012-02-12-0/+46
| | | | | | | | | | | The decompressor expects the L2 cache to be disabled. This fixes booting some kernels, which have CONFIG_ARM_PATCH_PHYS_VIRT enabled. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Wolfgang Denk <wd@denx.de>
* edminiv2: add USB host supportAlbert ARIBAUD2012-02-12-0/+14
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* orion5x: add USB host ehci-marvell supportAlbert ARIBAUD2012-02-12-0/+17
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Remove kirkwood-specifics from marvell EHCI driverAlbert ARIBAUD2012-02-12-14/+29
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Rename ehci-kirkwood as ehci-marvellAlbert ARIBAUD2012-02-12-2/+2
| | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* edminiv2: add hush parser, cmdline editing and long helpAlbert ARIBAUD2012-02-12-0/+10
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* kirkwood_spi: correct access to irq_mask registerIan Campbell2012-02-12-1/+1
| | | | | | | | | | | | Problem appears to have been present since day one but masked because alignment aborts were not enabled. ca4b55800ed7 "arm, arm926ejs: always do cpu critical inits" turned on alignment aborts and uncovered this latent problem. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-By: Jason Cooper <u-boot@lakedaemon.net> Tested-By: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* ARM: activate DISPLAY_CPUINFO for VCMA9 + SMDK2410 boardDavid Müller (ELSOFT AG)2012-02-12-4/+2
| | | | | Signed-off-by: David Mueller <d.mueller@elsoft.ch> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* i.mx: i.mx5: update imx_get_mac_from_fuse functionJason Liu2012-02-12-1/+1
| | | | | | | | | | | | | | | | | | | | FEC does not work on the i.mx51/53evk board, it will hangup In: serial Out: serial Err: serial Net: After bisect, it due to the following commit: be252b6 net: imx: Add multi-FEC support for imx_get_mac_from_fuse has change the imx_get_mac_from_fuse fucntion prototype, but fail to update i.mx5, here it does it. After apply this patch, u-boot works again on i.mx51/53 evk boards. Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* tt01: add MMC supportHelmut Raiger2012-02-12-2/+44
| | | | | | | | board_mmc_init() initializes the pins of SDHC1 and turns on V_MMC1 of the PMIC. Config adds support for EXT2 and FAT. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* mc13783.h: create and add regulator mode 0 and 1Helmut Raiger2012-02-12-0/+80
| | | | | | Add bit definitions for register 32 and 33 of Freescale MC13783. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* mx28: fix i.MX28 spi driverMatthias Fuchs2012-02-12-3/+9
| | | | | | | | | | | | | | | The generic spi flash driver (drivers/mtd/spi/spi_flash.c) uses the spi low level driver's spi_xfer() function with len=0 to deassert the SPI flash' chip select. But the i.MX28 spi driver rejects this call due to len=0. This patch implements an exception for len=0 with the SPI_XFER_END flag set. This results in an extra read with the chip select being deasserted afterwards. There seems to be no way to deassert the signal by hand. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx28: Show CPU frequencyFabio Estevam2012-02-12-1/+2
| | | | | | | | Showing CPU frequency during boot is useful information. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* imx6: mx6qarm2: updated board_mmc_getcd() to the new prototypeStefano Babic2012-02-12-4/+5
| | | | | | | | | | | | Commit 314284b1567f1ce29c19060641e7f213146f7ab8 has changed board_mmc_getcd() function prototype, while mx6qarm2 has still the old one. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* configs: Remove CONFIG_NET_MULTI from board filesFabio Estevam2012-02-12-30/+0
| | | | | | | | | | | | | | | | | | CONFIG_NET_MULTI is not used anymore, so remove it from board files. Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Kumar Gala <kumar.gala@freescale.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Heiko Schocher <hs@denx.de>
* mmc: access mxcmmc from mx31 boardsHelmut Raiger2012-02-12-29/+53
| | | | | | | | | | | | | | | | | This patch modifies mxcmmc.c to be used not only by i.MX27 but also by i.MX31 boards. Both use the same SD controller, but have different clock set-ups. The i.MX27 imx_get_XXXclock functions are made static to generic.c and a public mxc_get_clock() function is provided. Pins, base address and prototypes for an i.MX31 specific board_init_mmc() are provided. Some of the i.MX27 clock getters are unused and marked as such to avoid warnings (./MAKEALL -s mx27), but the code was left in for future use. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
* i.mx6q: mx6qsabrelite: Add the ethernet function supportJason Liu2012-02-12-2/+119
| | | | | | | Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de>
* i.mx6q: configs: Add fdt_high and initrd_high variablesDirk Behme2012-02-12-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | To be able to load the device tree and initrd correctly, set the fdt_high and initrd_high environment variables. Using 0xffffffff implies that the device tree and the initrd are initially copied to working addresses. This will avoid an additional copy. Loading the device tree to 0x30000000 and the initrd to 0x3c000000 should work for both boards, the ARM2 and SabreLite. Example (SabreLite): fatload mmc 0:2 0x10000000 uImage fatload mmc 0:2 0x3c000000 uInitrd fatload mmc 0:2 0x30000000 board.dtb bootm 0x10000000 0x3c000000 0x30000000 Note: This requires that the kernel has CONFIG_HIGHMEM enabled. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
* i.mx6q: mx6qsabrelite: Setup uart1 pinmuxTroy Kisky2012-02-12-0/+6
| | | | | | | | | | | This allows the Linux kernel to use UART1 before pinmux support is added for UART1 Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
* i.mx6: mx6x_pins: Fix uart txd definitionsTroy Kisky2012-02-12-24/+12
| | | | | | | | | | | | | The uart txd pad can also provide the rxd function. But it does not stop its tx role. This could be used for a half duplex serial port. Change names to reduce confusion. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
* imximage: Sort bootops alphabeticallyDirk Behme2012-02-12-3/+3
| | | | | | | | Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
* imximage: Add support for i.MX6Dirk Behme2012-02-12-7/+12
| | | | | | | | | | | | The i.MX6 processor can boot from NOR flash and SATA disks, additionally. Add the flash offsets for these additional boot modes. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
* imximage: Add MX53 to the documentationDirk Behme2012-02-12-1/+1
| | | | | | | | | | i.MX53 is supported, too. Add this to the introduction of the documentation. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org>
* sdhc_boot: Introduce CONFIG_FSL_FIXED_MMC_LOCATION optionFabio Estevam2012-02-12-1/+9
| | | | | | | | | | | | | | | | | | | Since commit 97039ab98 (env_mmc: Allow board code to override the environment address) mmc_get_env_addr is a weak-aliased function in common/env_mmc.c The mmc_get_env_addr implementation that exists at board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards, but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined. Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate this config option on their board file. This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefano Babic <sbabic@denx.de>
* arm, davinci: cam_enc_4xx board updatesHeiko Schocher2012-02-12-30/+771
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CONFIG_SYS_MMC_ENV_DEV, needed if environment on mmc - wait for 1 second timer in board_late_init() only, if timer is running. - add UBI/UBIFS support - add FIT images support - menu support - U-Boot max size now 0xa0000 - SPL now Block 0 page 0 - new MTD partitioning 0x00000000 SPL 0x00020000 UBL-Header 0x00040000 UBL-Header 0x00060000 UBL-Header 0x00080000 UBoot (0xa0000(U-Boot length) + 0x60000(3 spare blocks)) 0x00180000 ENV- Variablen (1) 0x001a0000 ENV- Variablen (2) 0x001c0000 ENV- Variablen (reserved for Bad Block) 0x001e0000 ENV- Variablen (reserved for Bad Block) 0x00200000 UBI-Device UBI Volumes: „default“: contain environment-default values „rootfs1“: UBIFS root-fs (1); contain linux kernel image „rootfs2“: UBIFS root-fs (2); contain linux kernel image „data-ro“: UBIFS data (read only) „data-rw“: UBIFS data (read/write) - new environment variables: - app_reset (this is only passed per cmdline to linux) - dvn_app_vers string from ramdisk description contained in the FIT image - dvn_boot_vers string from ubootimage description contained in the FIT image - saveparms, restoreparms, restoretmpparms, savetmpparms helper for saving network parameter. - ubiargs set ubi kernel cmdlinargs for booting with a ubifs rootfs - ubi_ubi boot with reading kernel image from ubifs, and use a ubifs as rootfs Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Wolfgang Denk <wd@denx.de>
* common, menu: do not trigger timeout again, if a line is readHeiko Schocher2012-02-12-1/+3
| | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Jason Hobbs <jason.hobbs@calxeda.com> Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
* common, menu: show menu on startup if CONFIG_MENU_SHOW is definedHeiko Schocher2012-02-12-0/+12
| | | | | | | | | show a menu on startup instead running the shell. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Jason Hobbs <jason.hobbs@calxeda.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
generated by cgit v1.1 at 2024-11-09 14:01:13 +0000