summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
* | | | sunxi: video: Add lvds supportHans de Goede2015-01-14-2/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for lvds lcd panels Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: add Linksprite pcDuino v1/v2 supportZoltan HERPAI2015-01-14-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for a sun4i board built by Linksprite. This addition covers both v1 and v2 versions. As the board has been working with 408MHz memory setting in the u-boot-sunxi branch, and has been proven to be running stable during my tests as well, a respective new DRAM config file is added as well. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | sunxi: video: Add a hpd_delay parameter to configure hpd delayHans de Goede2015-01-14-5/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In some extreme cases it may be necessary to wait 1.5 seconds or more for a hpd signal to show up (and be able to read edid info), but we do not want to penalize all headless boots with an extra second boot delay, so add a hpd_delay parameter which can be set through the video-mode env. variable. While at it raise the default from 300ms to 500ms as 300 may very well be too low in many cases. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Add VGA output supportHans de Goede2015-01-14-9/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for VGA directly from the sunxi SoC / display engine. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Fallback from HDMI to VGA on boards with VGAHans de Goede2015-01-14-24/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a board has no LCD, but does have VGA fallback to VGA when no HDMI cable is connected (unless hpd=0). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Add support for using PORTD hsync/vsync pins with tcon1Hans de Goede2015-01-14-3/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for using PORTD hsync/vsync pins with tcon1, this is a preparation patch for adding native VGA support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Use sunxi_lcdc_get_clk_delay to calculate tcon1 delayHans de Goede2015-01-14-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay instead of hardcoding it to 30. We will still end up using 30 for most modes, but for e.g. 800x600 this makes a (small) difference. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Remove sunxi_display.enabled variableHans de Goede2015-01-14-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Having both a sunxi_display.enabled variable and sunxi_display.monitor == sunxi_monitor_none duplicates state, use sunxi_display.monitor = sunxi_monitor_none when ever we do not have a display. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: Ippo_q8h defconfigs: Enable the LCD panel found on these tablets.Hans de Goede2015-01-14-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable the new LCD support on Ippo_q8h tablets. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Tested-by: Chen-Yu Tsai <wens@csie.org>
* | | | sunxi: A13-OLinuXino defconfigs: Enable VGA output, add lcd-mode for 7" LCDHans de Goede2015-01-14-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable VGA output on the A13-OLinuXino and A13-OLinuXinoM now that we've support for it. Also add LCD timing and gpio info for the Olimex 7" LCD module. We can safely put this in the default config on this boards, since by default we will always use VGA, and the LCD timing info will only get used if the user explicitly sets monitor=lcd in the video-mode env. variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: sunxi-common.h: Reduce bootm_size to take the framebuffer into accountHans de Goede2015-01-14-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before video output support can be enabled on the A13-OLinuXinoM, bootm_size must first be reduced to take into account that the framebuffer is shaved of the top of the DRAM. For other boards this is not an issue since bootm was set to 256M and all boards have at least 512M except for the A13-OLinuXinoM. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Add support for VGA via external DACs connected to the LCD pinsHans de Goede2015-01-14-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for external DACs connected to the parallel LCD interface driving a VGA connector, such as found on the Olimex A13 boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Enable video on sun8i, which supports LCD but not HDMIHans de Goede2015-01-14-4/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The A23 (sun8i) only has lcd output support, so allow building the video code without HDMI support for use with the A23. Also the A23 has the same reset bits (and necessity to enable the DRC block) as the sun6i, so enable those bits for sun8i too. Note building without HDMI support is useful for the A13 (sun5i variant) too, as that one does not have HDMI either. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Add lcd output supportHans de Goede2015-01-14-27/+278
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add lcd output support, see the new Kconfig entries and doc/README.video for how to enable / configure this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Move sunxi_drc_initHans de Goede2015-01-14-14/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move sunxi_drc_init to directly above sunxi_engines_init, to avoid unnecessary #ifdef-ery in later patches. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1Hans de Goede2015-01-14-7/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a preparation patch for adding lcd support. While at it also swap the divider search order, searching from low to high, as the comment above the code says we should do. In cases where there are multiple solutions this will result in picking a lower pll clock and divider, which is more stable and saves power. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Prepare for lcd supportHans de Goede2015-01-14-32/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Refactor sunxi_mode_set into a bunch of helpers, and make it do a switch case on sunxi_display.monitor to decide what to do. Also rename sunxi_lcdc_mode_set to sunxi_lcdc_tcon1_mode_set, as it sets the timings for tcon1, and for lcd support we need a similar function operating on tcon0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Improve monitor video-mode option handlingHans de Goede2015-01-14-16/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a sunxi_monitor enum and parse the monitor option string into this enum once, rather then doing strcmp-s on it in various places. This also adds checking for it being a valid value. This also adds new "none" and "lcd" values in preparation for lcd support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: gpio: Add support for gpio pins on the AXP209 pmicHans de Goede2015-01-14-0/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino board, which uses gpio0 of the axp209 for the lcd-power signal. This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c changes are universal, adding gpio support for the other AXP pmics (when necessary) should be a matter of adding the necessary axp_gpio_foo functions to their resp. drivers, and add "#define AXP_GPIO" to their header file. Note this commit only adds support for the non device-model version of the gpio code, patches for adding support to the device-model version are very welcome. The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix is there in case we need to support gpio-s on more then 1 pmic in the future. At least A80 boards have 2 pmics, and we may end up needing to support gpio-s on both. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: gpio: Properly sort mux defines by port numberHans de Goede2015-01-14-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move a few mux defines around so that all the mux defines are properly sorted by port number. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: video: Set input sync enableHans de Goede2015-01-14-23/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a write to the "unknown" (*) register to enable auto input sync, when initially adding sunxi hdmi output support this magic write from the android kernel code was missed, causing lcdc -> hdmi encoder sync problems. With this write added, we can drop the modesetting retries and the extra delays added to work around these sync problems. With the retries dropped there also is no need to 0 all the enable flags at the beginning of the modeset, as they are initialized to 0 already by engines_init. *) "unknown" is the actual name of this register in the android kernel sources Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Give hotplug-detect (hpd) signal some time to show upHans de Goede2015-01-14-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When using a hdmi powered hdmi to vga dongle, and cold booting a sunxi device, the hpd detect code would not see the dongle (until a warm reboot), because the dongle needs some time to boot. Testing has shown that this dongle needs 213ms to respond on a cold boot, so wait up to 300ms for a hpd signal to show up before giving up. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: When using edid use CEA681 extension blocks to select hdmi outputHans de Goede2015-01-14-9/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When using edid use CEA681 edid extension blocks to select between dvi and hdmi output formats, so that u-boot will automatically do the right thing. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Add sunxi_hdmi_edid_get_block helper functionHans de Goede2015-01-14-11/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a sunxi_hdmi_edid_get_block helper function, this is a preparation patch for adding support for parsing EDID extension blocks. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Add hdmi supportHans de Goede2015-01-14-15/+84
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far we've been programming the hdmi-encoder to send out dvi data over the hdmi connector. This works well for most devices, including hdmi devices, but not all devices accept dvi data on a hdmi input. Add support for sending proper hdmi data over the hdmi output found on most sunxi boards. This can be turned on by adding monitor=hdmi as option to the video-mode env. variable. A follow up patch will determine whether to send dvi or hdmi automatically when EDID is used. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Add DDC & EDID supportHans de Goede2015-01-14-1/+239
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DDC & EDID support and use it to automatically select the native mode of the attached monitor. This can be disabled by adding edid=0 as option to the video-mode env. variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Add hpd optionHans de Goede2015-01-14-9/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow the user to specify hpd=0 as option in the video-mode env. variable, if hpd is set to 0 then the hdmi output will be brought up even if no cable is connected. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Add support for video-mode environment variableHans de Goede2015-01-14-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the standard video-mode environment variable using the videomodes.c video_get_ctfb_res_modes() helper function. This will allow users to specify the resolution e.g. : setenv video-mode sunxi:video-mode=1280x1024-24@60 saveenv Also make the reserved fb mem slightly larger to allow 1920x1200 to work. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sunxi: video: Use video-mode/-timing from videomodesHans de Goede2015-01-14-31/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch from fb_videomode to ctfb_res_modes and use the predefined videotimings from videomodes.c, rather then defining our own. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | edid: Add struct and defines for cea681 extension blocksHans de Goede2015-01-14-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a struct describing the (fixed) bits of cea681 edid extension blocks, and defines for accessing various bitfields. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | edid: Add an edid_check_checksum() helper functionHans de Goede2015-01-14-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a helper function to check the checksum of an EDID data block. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | videomodes: Add video_edid_dtd_to_ctfb_res_modes helper functionHans de Goede2015-01-14-0/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a video_edid_dtd_to_ctfb_res_modes helper function to convert an EDID detailed timing to a struct ctfb_res_modes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | videomodes: Add helper functions to parse video-mode env-var extra optionsHans de Goede2015-01-14-1/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add 2 helper functions to get strings, respectively integers from the options value returned by video_get_video_mode() / video_get_ctfb_res_modes(). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | videomodes: Add video_get_ctfb_res_modes helper functionHans de Goede2015-01-14-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a video_get_ctfb_res_modes() helper function, which uses video_get_video_mode() to parse the 'video-mode' environment variable and then looks up the matching mode in res_mode_init and returns the matching mode. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | videomodes: Add a bunch of high res modesHans de Goede2015-01-14-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add modes useful for hd-tvs and modern monitors. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | videomodes: Add (vesa) standard timingsHans de Goede2015-01-14-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The timings for the modes defined in videomodes.c differ (significantly) from vesa standard timings for these modes. This commit adds a version with the proper std timings for these modes, since I do not want to cause regressions, boards which want to use the standard timings need to define CONFIG_VIDEO_STD_TIMINGS to get the new correct timings. Since there is no std timing for 960x720 this commit uses the timing used by the nvidia video drivers for 960x720, which uses a standard pixelclock of 74.25 MHz rather then the weird 76.335... clock used by the old modes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | videomodes: Add pixelclock_khz and refresh fields to ctfb_res_modesHans de Goede2015-01-14-7/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add pixelclock_khz and refresh fields to ctfb_res_modes: 1) pixelclocks are usually referred to in hz, not picoseconds, and e.g pll-s are also typically programmed in hz, not ps. Converting between the 2 leads to rounding differences, add a pixelclock_khz field to directly store the *exact* pixelclock for a mode, so that drivers do not need to resort to rounding tricks to try and guess the exact pixelclock; 2) The video-mode environment variable, as parsed by video_get_video_mode also contains the vertical refresh rate, add a refresh field, so that the refresh-rate can be matched when parsing the video-mode environment variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | | | sun7i: Add new Bananapro board / defconfigHans de Goede2015-01-14-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: Fix PLL1 running at half speed on sun8iHans de Goede2015-01-14-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PLL1 on sun6i / sun8i also has a p factor which divides the clock by 2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is used and we were setting it to 1, resulting in the CPU running at 504 MHz instead of 1008 MHz, this commit fixes this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: Fix buggy sun6i/sun8i DRAM size detection logicSiarhei Siamashka2015-01-14-18/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After reboot, reset or even short power off, DRAM typically retains the old stale data for some period of time (for this type of memory, the bits of data are stored in slowly discharging capacitors). The current sun6i/sun8i DRAM size detection logic, which is inherited from the Allwinner code, relies on using a large magic signature with the hope that it is unique enough and unlikely to ever accidentally match this leftover garbage data in RAM. But this approach is inherently unsafe, as can be demonstrated using the following test program: /***** A testcase for reproducing the problem ******/ void main(int argc, char *argv[]) { size_t size, i; uint32_t *buf; /* Allocate the buffer */ if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) || !(buf = malloc(size))) { printf("Need buffer size in MiB as a cmdline argument\n"); exit(1); } /* Fill it with the Allwinner DRAM "magic" values */ for (i = 0; i < size / 4; i++) buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64; /* Try to reboot */ system("reboot"); /* And wait */ for (;;) {} } /***************************************************/ If this test program is run on the device (giving it a large chunk of memory), then the DRAM size detection logic in u-boot gets confused after reboot and fails to initialize DRAM properly. A better approach is not to rely on luck and abstain from making any assumptions about the properties of the leftover garbage data in RAM. Instead just use a more reliable code for testing whether two different addresses refer to the same memory location. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | sun7i: Add defconfig for MSI Primo73 tabletSiarhei Siamashka2015-01-14-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch uses the same DRAM settings as in the pre-installed Android firmware. The LCD display is supported too. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | sun6i: Add defconfig for MSI Primo81 tabletSiarhei Siamashka2015-01-14-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch uses the same ZQ and DRAM clock settings as in the pre-installed Android firmware. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | sunxi: Fix CONFIG_UART0_PORT_F build and add it to menuconfigSiarhei Siamashka2015-01-14-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The CONFIG_UART0_PORT_F option has been supported since http://git.denx.de/?p=u-boot.git;a=commit;h=ff2b47f6a9cc1025 This option is primarily useful only for low level u-boot debugging on tablets, where normal UART0 is difficult to access and requires device disassembly and/or soldering. This patch now allows it to be selected from menuconfig. A dependency on SPL_FEL is added because u-boot does not support booting from NAND yet and also booting from SD card is impossible when a MicroSD breakout board is plugged into the SD slot. Additionally a compilation problem is fixed: common/spl/built-in.o: In function `spl_mmc_load_image': /tmp/u-boot-sunxi/common/spl/spl_mmc.c:94: undefined reference to `mmc_initialize' /tmp/u-boot-sunxi/common/spl/spl_mmc.c:96: undefined reference to `find_mmc_device' /tmp/u-boot-sunxi/common/spl/spl_mmc.c:104: undefined reference to `mmc_init' scripts/Makefile.spl:206: recipe for target 'spl/u-boot-spl' failed Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | sun8i: Add defconfig for Ippo_q8h v1.2Hans de Goede2015-01-14-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need separate defconfigs for the v5 and v1.2 versions of this board, as they use different DRAM parameters. Note they also use different dtb files, as the wifi is different too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sun8i: Ippo_q8h_v5_defconfig: Enable SPL supportHans de Goede2015-01-14-5/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we've sun8i dram-init support we can enable the SPL for sun8i boards. While at it also replace CONFIG_DEFAULT_DEVICE_TREE with CONFIG_FDTFILE, the former is for u-boot's own fdt usage, which we do not use (yet), the later specifies the fdt to pass to the kernel, which is the one we want. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sun8i: Add dram initialization supportHans de Goede2015-01-14-2/+625
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on the register / dram_para headers from the Allwinner u-boot / linux sources + the init sequences from boot0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: Use memcmp for mctl_mem_matchesHans de Goede2015-01-14-9/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use memcmp for mctl_mem_matches instead of DIY. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: Fill memory before comparing it when doing dram init on sun6iHans de Goede2015-01-14-14/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sun8i boot0 code fills the DRAM with a "random" pattern before comparing it at different offsets to do columns, etc. detection. The sun6i boot0 code does not do it, instead relying on the memory contents being random enough to begin with for the memcmp to properly detect the wrap-around address, iow it is working purely by chance. Since our sun6i dram code was modelled after the boot0 code it contained the same issue. This commit fixes this by filling the memory with a unique, distinct pattern. The new mctl_mem_fill function this introduces is added as an inline helper in dram.h, so that it can be shared with the sun8i dram code. While at it move mctl_mem_matches to dram.h for re-use in sun8i too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sunxi: Move await_completion dram helper to dram.hHans de Goede2015-01-14-37/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The await_completion helper is already copy pasted between the sun4i and sun6i dram code, and we need it for sun8i too, so lets make it an inline helper in dram.h, rather then adding yet another copy. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | | sun6i: clock_set_pll5: Calculate k and m rather then hardcoding themHans de Goede2015-01-14-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Our old hardcoded k and m values are based on PLL5 being configured in steps of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i) the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps. This commit adjusts clock_set_pll5 to automatically select the best k and m depending on the requested clk rate. Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>