summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* dm: power: Allow regulators to be omitted from SPLSimon Glass2016-01-21-2/+34
| | | | | | | | For some boards the pmic interface is useful but the regulator interface (which comes with it) is too large. Allow them to be separated such that SPL can decide which it needs. Signed-off-by: Simon Glass <sjg@chromium.org>
* spi: Correct device tree usage in spi_flash_decode_fdt()Simon Glass2016-01-21-6/+3
| | | | | | | | | | | This function currently searches the entire device tree for a node that it thinks is relevant. But the node is known and is passed in. Correct the code and enable it only with driver model, since only driver-model boards will use it. This avoids bringing in a large number of strings from fdtdec. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: i2c: Allow muxes to be enabled for SPL separatelySimon Glass2016-01-21-3/+12
| | | | | | | Since I2C muxes are seldom needed in SPL, and the code for this increases the size somewhat, add a separate option to enable I2C muxes for SPL. Signed-off-by: Simon Glass <sjg@chromium.org>
* cros_ec: Disable the Chrome OS EC in SPLSimon Glass2016-01-21-0/+2
| | | | | | | This is not used in SPL so don't allow it to be built there, even if I2C is enabled in SPL. Signed-off-by: Simon Glass <sjg@chromium.org>
* gpio: Allow 's' as an abbreviation for 'status'Simon Glass2016-01-21-1/+1
| | | | | | | The 'gpio' command allows abbreviations for most subcommands. Allow them for 'status' also. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: jerry: Drop unused optionsSimon Glass2016-01-21-5/+2
| | | | | | | To reduce the SPL image size, drop the LED features. Jerry does not have an LED and we can leave out GPIO support also. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Disable simple-bus in SPL for firefly-rk3288, jerrySimon Glass2016-01-21-0/+2
| | | | | | This is not needed for booting, so drop it from SPL to save about 300 bytes. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: jerry: Enable the RK808 PMIC and regulatorSimon Glass2016-01-21-0/+2
| | | | | | Enable this PMIC and regulator, which is used on jerry. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Move firefly and jerry to use the full pinctrlSimon Glass2016-01-21-2/+0
| | | | | | Use the full pinctrl driver in U-Boot proper. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: pinctrl: Add a full pinctrl driverSimon Glass2016-01-21-1/+229
| | | | | | | We can make use of the device tree to configure pinctrl settings. Add this support for the driver so we can use it in U-Boot proper. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: mmc: Update the driver to use the new clock IDSimon Glass2016-01-21-1/+1
| | | | | | We can use the new clk_get_by_index() function to get the correct clock. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: spi: Avoid setting the pinctrl twiceSimon Glass2016-01-21-3/+6
| | | | | | | | If full pinctrl is enabled we don't need to manually set the pinctrl in the driver. It will happen automatically. Adjust the code to suit - we will still use manual mode in SPL. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: spi: Update the driver to use the new clock IDSimon Glass2016-01-21-15/+17
| | | | | | We can use the new clk_get_by_index() function to get the correct clock. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: i2c: Update the driver to use the new clock IDSimon Glass2016-01-21-16/+22
| | | | | | We can use the new clk_get_by_index() function to get the correct clock. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: clock: Add a function to find a clock by IDSimon Glass2016-01-21-2/+34
| | | | | | | | The current approach of using uclass_get_device() is error-prone. Another clock (for example a fixed-clock) may cause it to break. Add a function that does a proper search. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: clk: Add a function to get a peripheral clock rateSimon Glass2016-01-21-0/+37
| | | | | | | It is useful to be able to read the rate of a peripheral clock. Add a handler for that. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: clock: Rename the general clock variable to gclk_rateSimon Glass2016-01-21-12/+12
| | | | | | The current name is confusing and a bit verbose. Rename it. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Use a separate clock ID for clocksSimon Glass2016-01-21-44/+50
| | | | | | | | | | At present we use the same peripheral ID for clocks and pinctrl. While this works it is probably better to use the device tree clock binding ID for clocks. We can use the clk_get_by_index() function to find this. Update the clock drivers and the code that uses them. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: jerry: Disable pmic-int-1 setup to avoid a hangSimon Glass2016-01-21-1/+4
| | | | | | | This hangs when activated (by probing the PMIC). Disable it for now until we understand the root cause. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Use pwrseq for MMC start-up on jerrySimon Glass2016-01-21-4/+13
| | | | | | | This is defined in the device tree in Linux. Copy over the settings so that this can be used instead of hard-coding the reset line. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Correct the defconfig orderSimon Glass2016-01-21-5/+5
| | | | | | This has got out of sequence somehow. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: mmc: Use a pwrseq device if availableSimon Glass2016-01-21-0/+47
| | | | | | | Use the pwrseq uclass to find a suitable power sequence for the MMC device. If this is enabled in the device tree, we will pick it up automatically. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Convert the PMU IOMUX registers into an arraySimon Glass2016-01-21-6/+10
| | | | | | | | | This is easier to deal with when using generic code since it allows us to use a register index instead of naming each register. Adjust it, adding an enum to improve readability. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: Avoid using MMC code when not booting from MMCSimon Glass2016-01-21-0/+2
| | | | | | This saves some code space in SPL which is useful on jerry. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: Add a power sequencing uclassSimon Glass2016-01-21-0/+62
| | | | | | | | Some devices need special sequences to be used when starting up. Add a uclass for this. Drivers can be added to provide specific features as needed. Signed-off-by: Simon Glass <sjg@chromium.org>
* power: Add support for RK808 regulatorsSimon Glass2016-01-21-0/+311
| | | | | | | Add regulator support for the RK808 PMIC. It integrated 4 BUCKs and 8 LDOs all of which are supported by this driver. Signed-off-by: Simon Glass <sjg@chromium.org>
* power: Add base support for the RK808 PMICSimon Glass2016-01-21-0/+183
| | | | | | | | | | This Rockchip PMIC provides features suitable for battery-powered applications. It is commonly used with Rockchip SoCs. Add a driver which provides register access. The regulator driver will use this. Signed-off-by: Simon Glass <sjg@chromium.org>
* dts: Bring in pinctrl device tree bindingSimon Glass2016-01-21-0/+236
| | | | | | Add this binding file since we now use it in U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: pmic: Add 'reg status' to show all regulatorsSimon Glass2016-01-21-10/+56
| | | | | | | It is convenient to be able to see the status of all regulators in a list. Add this feature to the 'reg status' command. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: pinctrl: Add a function to parse PIN_CONFIG flagsSimon Glass2016-01-21-0/+25
| | | | | | | | Add a function which produces a flags word from a few common PIN_CONFIG settings. This is useful for simple pinctrl drivers that don't need to worry about drive strength, etc. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: core: Don't set pinctrl for pinctrl devicesSimon Glass2016-01-21-2/+4
| | | | | | | | | | | | | | There is sort-of race condition when a pinctrl device is probed. The pinctrl function is called which may end up using the same device as is being probed. This results in operations being used before the device is actually probed. For now, disallow pinctrl operations on pinctrl devices while probing. An alternative solution would be to move the operation to later in the device_probe() function (for pinctrl devices only) but this needs more thought. Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: kylin: Store env in emmcJeffy Chen2016-01-21-0/+12
| | | | | | | | There's a 64K reserved area at the end of the first 4M. Store env there, so we can use fastboot to flash it. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
* rockchip: kylin: Check fastboot requestJeffy Chen2016-01-21-0/+35
| | | | | | | | | We will save boot mode flag in grf's os_reg[4], if fastboot requested or fastboot key pressed, try to enter fastboot mode at preboot stage. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
* rockchip: kylin: Add default gpt partition tableJeffy Chen2016-01-21-0/+29
| | | | | | | | | | Add default android gpt partition table for kylin board. Use "gpt write mmc 0 $partitions" to apply. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* rockchip: rk3036: Bind GPIO banksJeffy Chen2016-01-21-0/+8
| | | | | | | | Call dm_scan_fdt_node() in rk3036 pinctrl uclass binding. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: bootm: Try to use relocated ramdiskJeffy Chen2016-01-21-1/+11
| | | | | | | | | After boot_ramdisk_high(), ramdisk would be relocated to initrd_start & initrd_end, so use them instead of rd_start & rd_end. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* dm: clk: Add support for decoding clocks from the device treeSimon Glass2016-01-21-0/+52
| | | | | | | | | Add a method which can locate a clock for a device, given its index. This uses the normal device tree bindings to return the clock device and the first argument which is normally used as a peripheral ID in U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* clk: add fixed rate clock driverMasahiro Yamada2016-01-21-1/+58
| | | | | | | | | | | | This commit intends to implement "fixed-clock" as in Linux. (drivers/clk/clk-fixed-rate.c in Linux) If you need a very simple clock to just provide fixed clock rate like a crystal oscillator, you do not have to write a new driver. This driver can support it. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
* Merge git://git.denx.de/u-boot-dmTom Rini2016-01-21-422/+7455
|\
| * dm: video: test: Test that bitmap display works correctlySimon Glass2016-01-20-0/+56
| | | | | | | | | | | | | | | | Add a test for the 'bmp' command. Test both the uncompressed and compressed versions of the file, since they use different code paths. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: video: test: Add tests for rotated consolesSimon Glass2016-01-20-0/+28
| | | | | | | | | | | | | | Test that text is displayed correctly when the console is rotated. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: video: test: Add tests for the video uclassSimon Glass2016-01-20-9/+206
| | | | | | | | | | | | | | | | | | Add tests that check that the video console is working correcty. Also check that text output produces the expected result. Test coverage includes character output, wrapping and scrolling. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: video: sandbox: Convert sandbox to use driver model for videoSimon Glass2016-01-20-86/+56
| | | | | | | | | | | | | | | | Now that driver model support is available, convert sandbox over to use it. We can remove a few of the special hooks that sandbox currently has. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * sandbox: Move CONFIG_VIDEO_SANDBOX_SDL to KconfigSimon Glass2016-01-20-2/+11
| | | | | | | | | | | | | | | | Move this option to Kconfig. This is quite simple as only sandbox uses the driver. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: stdio: video: Plumb the video uclass into stdioSimon Glass2016-01-20-4/+15
| | | | | | | | | | | | | | | | | | Register video drivers with stdio so that they can be used for text output. This needs to be done explicitly for now. At some point we should be able to convert stdio itself to driver model and avoid this step. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: video: Implement the bmp command for driver modelSimon Glass2016-01-20-1/+375
| | | | | | | | | | | | | | | | | | This command can use the bitmap display code in the uclass. This is similar to the code in lcd.c and cfb_console.c. These other copies will go away when all boards are converted to use driver model for video. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: common: Add memory reservation for the video uclassSimon Glass2016-01-20-12/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | Before relocation we need to reserve memory for the video driver frame buffers so that they can use this memory when they start up (after relocation). Add a call to the uclass to permit this. The current top and bottom of the region is stored in global_data so that it can be checked post-relocation to ensure enough memory is available. No video device should be probed before relocation. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * common: Move LCD and video memory reservation togetherSimon Glass2016-01-20-14/+14
| | | | | | | | | | | | | | | | These two functions are conceptually the same. Move them together in the pre-relocation init. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: video: Add a driver for a rotated text consoleSimon Glass2016-01-20-0/+450
| | | | | | | | | | | | | | | | | | Sometimes the console must be rotated. Add a driver which supports rotating the text clockwise to 90, 180 and 270 degrees. This can support devices where the display is rotated for mechanical reasons. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
| * dm: video: Add a 'normal' text console driverSimon Glass2016-01-20-1/+142
| | | | | | | | | | | | | | | | | | | | Most of the time we don't need to rotate the display so a simple font blitting feature is enough for our purposes. Add a simple driver which supports this function. It provides text output on the console using the standard 8x16-pixel font. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
generated by cgit v1.1 at 2024-11-09 05:43:27 +0000