summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
* ARM: tegra: enable GPU node by compatible valueStephen Warren2016-05-04-15/+22
| | | | | | | | | | | | | | | | | | | In current Linux kernel Tegra DT files, 64-bit addresses are represented in unit addresses as a pair of comma-separated 32-bit values. Apparently this is no longer the correct representation for simple busses, and the unit address should be represented as a single 64-bit value. If this is changed in the DTs, arm/arm/mach-tegra/board2.c:ft_system_setup() will no longer be able to find and enable the GPU node, since it looks up the node by name. Fix that function to enable nodes based on their compatible value rather than their node name. This will work no matter what the node name is, i.e for DTs both before and after any rename operation. Cc: Thierry Reding <treding@nvidia.com> Cc: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* include/configs: Numerous typo fixes: "controler" -> "controller".Robert P. J. Day2016-05-03-82/+82
| | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* net: increase maximum frame size to accomediate VLAN packetsStefan Agner2016-05-03-11/+5
| | | | | | | | | | | Ethernet packages with IEEE 802.1Q VLAN support may be up to 1522 bytes long. Increase the default size used to allocate packet storage by 4 bytes. While at it, let git care about history and rewrite the comment to represent the situation today only. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* net: fix vlan validationStefan Agner2016-05-03-2/+2
| | | | | | | | VLAN identifiers are 12-bit decimal numbers, not IP addresses. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* drivers: net: ldpaa: Memset pools_params as "0" before usePrabhakar Kushwaha2016-05-03-0/+1
| | | | | | | | Memset pools_params as "0" to avoid garbage value in dpni_set_pools. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reported-by: Jose Rivera <german.rivera@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* fdt: fix setting MAC addresses for multiple interfacesLev Iserovich2016-05-03-6/+14
| | | | | | | | | | For multiple ethernet interfaces the FDT offset of '/aliases' will change as we are adding MAC addresses to the FDT. Therefore only the first interface ('ethernet0') will get properly updated in the FDT, with the rest getting FDT errors when we try to set their MAC address. Signed-off-by: Lev Iserovich <iserovil@deshawresearch.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* usb: dwc2: Init desc_before_addrMarek Vasut2016-05-03-0/+3
| | | | | | | | | | | Initialize desc_before_addr, otherwise the USB core won't send the first 64B Get Device Descriptor request in common/usb.c function usb_setup_descriptor() . There are some USB devices which expect this sequence and otherwise can misbehave. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Tom Rini <trini@konsulko.com>
* usb: dwc2: Make OC protection configurableMarek Vasut2016-05-03-3/+14
| | | | | | | | | | Introduce a new flag in the controller private data, which allows selectively disabling the OC protection. Use the standard 'disable-over-current' OF prop to set this flag. This OC protection must be disabled on EBV SoCrates rev 1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Dinh Nguyen <dinguyen@kernel.org>
* usb: dwc2: Pull Ext VBUS macro from dwc_otg_core_init()Marek Vasut2016-05-03-7/+14
| | | | | | | | | | | Introduce a boolean flag in the dwc2 controller private data and set it according to the macro (for now) instead of having this macro directly in the dwc_otg_core_init(). This will let us configure the flag from DT or such later on, if needed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Dinh Nguyen <dinguyen@kernel.org>
* usb: dwc2: Pass private data into dwc_otg_core_init()Marek Vasut2016-05-03-2/+3
| | | | | | | | | | Pass the whole bulk of private data instead of just the regs, since the private data will soon contain important configuration flags. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Dinh Nguyen <dinguyen@kernel.org>
* igep00x0: Use the SRAM available for SPL.Enric Balletbo i Serra2016-05-03-0/+7
| | | | | | | | | | | Move CONFIG_SPL_TEXT_BASE down to 0x40200000 and set CONFIG_SPL_MAX_SIZE to (SRAM_SCRATCH_SPACE_ADDR - CONFIG_SPL_TEXT_BASE), so that it's clear what the limit is. This will also help some compilers to fit all the code into the allocated space. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
* mkimage: fix generation of FIT imageAndreas Bießmann2016-05-03-6/+3
| | | | | | | | | | | Commit 7a439cadcf3192eb012a2432ca34670b676c74d2 broke generation of SPL loadable FIT images (CONFIG_SPL_LOAD_FIT). Fix it by removing the unnecessary storage of expected image type. This was a left over of the previous implementation. It is not longer necessary since the mkimage -b switch always has one parameter. Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
* i2c/eeprom: Always define I2C_RXTX_LENMario Six2016-05-03-0/+4
| | | | | | | | | | | I2C_RXTX_LEN from include/i2c.h is not defined if CONFIG_DM_I2C is enabled. This leads to a compilation error on boards that enable both CONFIG_CMD_EEPROM and CONFIG_DM_I2C. To avoid this, we define I2C_RXTX_LEN in cmd/eeprom.c if it is not already defined. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mx6ul_evk: Remove CONFIG_SUPPORT_EMMC_BOOTFabio Estevam2016-05-02-1/+0
| | | | | | | | | | | | | | | | | | mx6ul_evk does not come with a eMMC populated, so we should not define CONFIG_SUPPORT_EMMC_BOOT as it causes SPL to not be able to boot some brands of SD cards, such as SanDisk microSD HC - 8GB: U-Boot SPL 2016.05-rc1-28384-g108f841 (Apr 19 2016 - 11:19:11) Trying to boot from MMC1 spl: mmc block read error SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### When CONFIG_SUPPORT_EMMC_BOOT is defined spl_boot_mode() returns MMCSD_MODE_EMMCBOOT, so remove this option to have a reliable boot via SD card. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* kbuild: Do not append dtb for OF_EMBED caseMichal Simek2016-05-02-1/+1
| | | | | | | | | | | dtb is already included in binary that's why there is no need to replace u-boot-spl.bin with u-boot-spl-dtb.bin. This is only needed for OF_SEPARATE is enabled. Only copy -nodtb.bin version which is straight output from objcopy -O binary. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* fit_image: Fix a double close() on the error pathSimon Glass2016-05-02-1/+0
| | | | | | | There is an extra close() call which is not needed. Reported-by: Coverity (CID: 143065) Signed-off-by: Simon Glass <sjg@chromium.org>
* tools: env: fix config file loading in env libraryAnatolij Gustschin2016-05-02-0/+3
| | | | | | | | | | | | env library is broken as the config file pointer is only initialized in main(). When running in the env library parse_config() fails: Cannot parse config file '(null)': Bad address Ensure that config file pointer is always initialized. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* config: am335x_evm: detect BoneGreen using BBG1matwey.kornilov@gmail.com2016-05-02-6/+3
| | | | | | | Since 770e68c0a37fded897d4bdda661614fc81cb33d2 BoneGreen is detected in board_late_init as board_name 'BBG1' Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
* Fix spelling of "occurred".Vagrant Cascadian2016-05-02-32/+32
| | | | | Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* Change my mailaddressAndreas Bießmann2016-05-02-23/+24
| | | | | | I'll switch my mails to my own server, so drop all gmail references. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* mkimage: fix argument parsing on BSD systemsAndreas Bießmann2016-05-02-25/+16
| | | | | | | | | | | The getopt(3) optstring '-' is a GNU extension which is not available on BSD systems like OS X. Remove this dependency by implementing argument parsing in another way. This will also change the lately introduced '-b' switch behaviour. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* arch/arm/imx-common/Makefile: Update u-boot.uim MKIMAGEFLAGSTom Rini2016-05-02-1/+1
| | | | | | We need to be passing -T firmware here and aren't. Signed-off-by: Tom Rini <trini@konsulko.com>
* fs: ext4: fix symlink read functionRonald Zachariah2016-05-02-1/+1
| | | | | | | | | | The function ext4fs_read_symlink was unable to handle a symlink which had target name of exactly 60 characters. Signed-off-by: Ronald Zachariah <rozachar@cisco.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Cc: Tom Rini <trini@konsulko.com>
* Revert "rockchip: rk3288: correct sdram setting"Vagrant Cascadian2016-05-02-7/+7
| | | | | | | | | | This reverts commit b5788dc0dd9570e98552833767f4373db965985d. Ram size is incorrectly reported as 512MB on a firefly-rk3288 board with 2GB of ram. Reverting this patch displays the full amount of ram. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Acked-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini2016-05-02-29/+47
|\
| * ARM: uniphier: move pin-mux code into pin_init functionMasahiro Yamada2016-05-01-27/+5
| | | | | | | | | | | | | | The code in uniphier_sld3_sbc_init() is pin-muxing, so it would be a better fit in uniphier_sld3_early_pin_init(). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
| * ARM: uniphier: allow to use System Bus for ROM boot mode of PH1-LD20Masahiro Yamada2016-05-01-1/+37
| | | | | | | | | | | | | | | | | | The System Bus is not available by default on the ROM boot mode of PH1-LD20. To use devices connected to the System Bus, such as the Micro Support Card, it is necessary to set up pin-muxing and some System Bus Controller register. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
| * ARM: uniphier: enable Peripherl clock to use UART in SPLMasahiro Yamada2016-05-01-0/+4
| | | | | | | | | | | | This is needed to use UART on SPL. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
| * ARM: uniphier: fix boot mode table of PH1-LD20Masahiro Yamada2016-05-01-1/+1
| | | | | | | | | | | | | | PH1-LD20 does not have the dedicated boot swap select latch. Instead, it is controlled from the boot mode select. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | Revert "omap3: Use raw SPL by default for mmc1"Tom Rini2016-05-02-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Unfortunately with this change we now are unable to do FS mode boots from MMC1 as with the way the code works today we will always load and assume that the hard-coded raw location contains U-Boot. Further, we cannot fix this by just changing other logic to try FS-then-RAW as it would also make us have to ignore what order the ROM is telling us to try. This reverts commit 22d90d560a2b01c47f180e196e6c6485eb8e65db. Signed-off-by: Tom Rini <trini@konsulko.com>
* | Revert "ti_armv7_common.h: Fix U-Boot location on eMMC"Tom Rini2016-05-02-2/+2
|/ | | | | | | | | We cannot change the long standing hard-coded offset for raw boot mode for everyone to accommodate how Android expects things to be done here. This reverts commit ef5ebe951bec72631cdbc7cef9079e6c684e5d0b. Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini2016-04-28-7/+23
|\
| * drivers/video/am335x-fb: Properly point framebuffer behind paletteMartin Pietryka2016-04-28-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DMA was outputting the palette on the screen because the base for the DMA was not after the palette. In addition to that, the ceiling was also too high, this led that the output on the screen was shifted. NOTE: According to the TRM, even in 16/24bit mode a palette is required in the first 32 bytes of the framebuffer. See also: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/234967/834483#834483 "In this mode, the LCDC will assume all information is data and thus you need to ensure that the DMA points to the first pixel of data and not the first entry in the frame buffer which is the beginning of the 512 byte palette." Signed-off-by: Martin Pietryka <martin.pietryka@chello.at> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
| * drivers/video/am335x-fb: Add support for 16bpp formatMartin Pietryka2016-04-28-3/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To support 16bpp we just need to change the raster_ctrl register accordingly. Also 32bpp mode should work as well, but was not tested. According to the TRM the uppermost byte will be ignored when LCD_TFT_24BPP_UNPACK is set. The switch logic is based on the Linux kernel tilcdc driver: drivers/gpu/drm/tilcdc/tilcdc_crtc.c: lines 407 through 419 (kernel was checked out at commit: bcc981e9ed8) Signed-off-by: Martin Pietryka <martin.pietryka@chello.at> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
* | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2016-04-28-0/+3
|\ \
| * | sunxi: Enable LDO3 at 3.3V on A13-OLinuXino boardHans de Goede2016-04-27-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | LDO3 is used for the VGA output, this fixes a regression where the VGA output on these boards would no longer work. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * | sunxi: mctl_mem_matches: Add missing memory barrierHans de Goede2016-04-27-0/+2
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We are running with the caches disabled when mctl_mem_matches gets called, but the cpu's write buffer is still there and can still get in the way, add a memory barrier to fix this. This avoids mctl_mem_matches always returning false in some cases, which was resulting in: U-Boot SPL 2015.07 (Apr 14 2016 - 18:47:26) DRAM: 1024 MiB U-Boot 2015.07 (Apr 14 2016 - 18:47:26 +0200) Allwinner Technology CPU: Allwinner A23 (SUN8I) DRAM: 512 MiB Where 512 MiB is the right amount, but the DRAM controller would be initialized for 1024 MiB. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | omap3: Reduce logic/overo SPL max image sizeTom Rini2016-04-27-2/+2
|/ | | | | | | | | | | | While the OMAP3 has 64KiB of SRAM, per the TRM the download area is only from 0x40200000 to 0x4020F000 and exceeding that will cause failure to boot. Further, we need to make sure that we don't run into SRAM_SCRATCH_SPACE_ADDR as once SPL is running we will write values there and would corrupt our running image. Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM64: zynqmp: Cleanup config file after CMD moveMichal Simek2016-04-26-4/+0
| | | | | | | | | The patch: "configs: Re-sync almost all of cmd/Kconfig" (sha1: 78d1e1d0a157c8b48ea19be6170b992745d30f38) doesn't remove empty if-endif. This patch is fixing it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: uniphier: revive some commands lost by Kconfig re-syncMasahiro Yamada2016-04-26-0/+2
| | | | | | | The recently added uniphier_ld20_defconfig missed the tree-wide re-sync by commit 89cb2b5f8be4 ("configs: Re-sync with cmd/Kconfig"). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini2016-04-26-4/+7
|\
| * exynos: Set CNTFRQAlexander Graf2016-04-14-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 73a1cb27 moved the check whether we should set the architected timer frequency from CONFIG_SYS_CLK_FREQ to CONFIG_TIMER_CLK_FREQ, but did not update all users of it. The one where I (finally) realized why KVM didn't work is the Arndale board, so this patch adds the respective define to it. Signed-off-by: Alexander Graf <agraf@suse.de> Fixes: 73a1cb27 Reviewed-by: York Sun <york.sun@nxp.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * odroid: Update README with correct firmware link and XU4 supportShawn Guo2016-04-14-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The firmware from link [1] only works with U-Boot image that is no bigger than 328KiB. Using it with the default mainline U-Boot today which is already around 500KiB is just not working. Correct the link to be hardkernel_1mb_uboot one [2], so that users can get mainline U-Boot work out of box. While at it, the README is updated to include XU4 support, like DTB file name. [1] https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel [2] https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel_1mb_uboot Signed-off-by: Shawn Guo <shawnguo@kernel.org> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Reviewed-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | Prepare v2016.05-rc3Tom Rini2016-04-25-1/+1
| | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* | pico-imx6ul: Update the defconfigTom Rini2016-04-25-9/+18
| | | | | | | | | | | | | | | | | | The defconfig/config.h file were merged but were already out of sync with mainline. This brings them further into line now. Cc: Richard Hu <richard.hu@technexion.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini2016-04-25-1/+1
|\ \
| * | drivers/video/am335x-fb: Fix bits for LCD_PALMODE_RAWDATA definitionMartin Pietryka2016-04-25-1/+1
| | | | | | | | | | | | | | | | | | | | | According to the TRM you have to set bits [21:20] to 0b10 for RAW mode, so (0x10 << 20) is obviously wrong here. Signed-off-by: Martin Pietryka <martin.pietryka@chello.at>
* | | pci: Device scanning range fixYoshinori Sato2016-04-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The terminal condition in the area where a PCI device is scanned is wrong, and 1f.7 isn't scanned. Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | | mmc: sdhci: add const qualifier to the name of struct sdhci_hostMasahiro Yamada2016-04-25-4/+4
| | | | | | | | | | | | | | | | | | | | | This allows to drop annoying (char *) casts when setting the host name of struct sdhci_host. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | ARM: DRA7: Add ABB setup for all domainsNishanth Menon2016-04-25-0/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ABB should be initialized for all required domains voltage domain for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units and has been hard to debug. This specifically is a concern with DRA7 generation of SoCs since other than VDD_MPU, all other domains are only permitted to setup the voltages to required OPP only at boot. Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
generated by cgit v1.1 at 2024-11-08 11:32:07 +0000