summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* rockchip: video: fix mpixelclock in rockchip HDMINickey Yang Nickey Yang2017-01-11-10/+10
| | | | | | Correct mpixelclock errors in rockchip_phy_config[] and rockchip_mpll_cfg[]. Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
* rockchip: rk3288: set isp/vop qos priority levelNickey Yang Nickey Yang2017-01-11-0/+40
| | | | | | | | Isp-camera preview image will be broken when dual screen display mode. This patch set isp/vop qos level higher to solve this problem. We have verified this patch on rk3288-miniarm board. Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
* arm64: rk3399: update rockchip_get_cru APIKever Yang2017-01-11-3/+3
| | | | | | | | rk3399 has two clock-controller: cru and pmucru, update the rockchip_get_crui() API, and rockchip_get_clk() do not used for other module. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
* dts: arm64: rk3399: add max-frequency for sdhciKever Yang2017-01-11-0/+1
| | | | | | | Add 'max-frequency' for sdhci node for clock init. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: rockchip_sdhci: add clock init for mmcKever Yang2017-01-11-2/+17
| | | | | | | Init the clock rate to max-frequency from dts with clock driver api. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* rockchip: Fix veyron-minnie's Kconfig descriptionMartin Michlmayr2017-01-11-1/+1
| | | | | | | The veyron-minnie Kconfig referred to jerry by mistake. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Acked-by: Simon Glass <sjg@chromium.org>
* rockchip: configs: make rk3036 env config same as rk3288Jacob Chen2017-01-11-3/+14
| | | | | | To make rockchip soc keep the same partition map Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
* rockchip: configs: correct env offset when enable ↵Jacob Chen2017-01-11-0/+36
| | | | | | | | | | CONFIG_ROCKCHIP_SPL_BACK_TO_BROM With CONFIG_ROCKCHIP_SPL_BACK_TO_BROM enabled, the environment is inside u-boot. So solve it by moving environment after u-boot. Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
* rockchip: dts: popmetal: add usb host power supply nodeKever Yang2017-01-11-0/+23
| | | | | | | | | | | The popmetal board using a HOST_VBUS_DRV gpio signal to control the USB host port 5V power, add a fix regulator and pinctrl for it, and enable the USB host1 controller with the vbus-supply. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: config: popmetal: enable the USB host controller and functionKever Yang2017-01-11-0/+10
| | | | | | | | | | RK3288 using the dwc2 USB host controller, enable it and other usb host funtion like storage and ether. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
* rockchip: board: popmetal: de-assert the host rst pin in board initKever Yang2017-01-11-0/+17
| | | | | | | | | | The PopMetal board have a on board FE1.1 usb 2.0 hub which connect to the usb host port, we need to de-assert its reset pin to enable it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
* SPL: Adjust more debug prints for ulong entry_pointTom Rini2017-01-11-2/+2
| | | | | | | | With entry_point now being an unsigned long we need to adapt the last two debug prints to use %lX not %X. Fixes: 11e1479b9e67 ("SPL: make struct spl_image 64-bit safe") Signed-off-by: Tom Rini <trini@konsulko.com>
* power_i2c.c: Fix unused variable warningTom Rini2017-01-11-1/+0
| | | | | | | | The variable ret was added but never set as we did not make calls to other functions that we needed to check the return value on. Fixes: 505cf4750ae5 ("power: change from meaningless value to error number") Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge tag 'xilinx-for-v2017.03' of git://www.denx.de/git/u-boot-microblazeTom Rini2017-01-11-63/+489
|\ | | | | | | | | | | | | | | | | | | Xilinx changes for v2017.03 - ATF handoff - DT syncups - gem: Use wait_for_bit(), add simple clk support - Simple clk driver for ZynqMP - Other small changes
| * ARM64: zynqmp: Move CONFIG_AHCI from board fileMichal Simek2017-01-11-1/+1
| | | | | | | | | | | | Move configuration option from board file to defconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * xilinx_phy: Pass correct pointer to fdtdec_get_int()Kamensky Ivan2017-01-11-2/+2
| | | | | | | | | | | | | | | | | | | | | | This patch fixes incorrect pointer on offset device in device tree blob. When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII" it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying to change frequency. Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * ARM64: zynqmp: Generate handoff structure for ATFMichal Simek2017-01-10-1/+101
| | | | | | | | | | | | | | | | | | | | | | | | | | Xilinx ATF extending options for passing images from BL2(FSBL) to BL31. U-Boot SPL is FSBL replacement that's why it should generate handoff structure the same. Support only one entry which is U-Boot in EL2 itself. When FIT image is adopted structure generate should be data driven. Currently ATF is placing this structure at the beggining of OCM which is rewriting early parts of ATF which should be unused at that time. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * fpga: Use enum for bitstream command typesMichal Simek2017-01-10-9/+11
| | | | | | | | | | | | | | Using enum simplify handling of different bitstream command types. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynqmp: Make SYS_VENDOR configurableMike Looijmans2017-01-10-0/+1
| | | | | | | | | | | | | | Add a string description for SYS_VENDOR to allow configuring boards from other vendors than just "xilinx". Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM64: zynqmp: Fix i2c node's compatible stringMoritz Fischer2017-01-10-2/+2
| | | | | | | | | | | | | | | | | | | | | | The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core which fixes some silicon bugs that needed software workarounds in Version 1.0 that was used on Zynq systems. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * i2c: cdns: Add additional compatible string for r1p14 of the IP.Moritz Fischer2017-01-10-0/+1
| | | | | | | | | | | | | | | | | | Adding additional compatible string for version 1.4 of the IP block. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * net: zynq_gem: Use clock driver for ZynqMPSiva Durga Prasad Paladugu2017-01-10-0/+20
| | | | | | | | | | | | | | | | | | Enable and use the clock driver routine defined in clock driver toset required clock appropriately. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * clk: zynqmp: Add clock driver support for zynqmpSiva Durga Prasad Paladugu2017-01-10-0/+249
| | | | | | | | | | | | | | | | | | Add basic clock driver support for zynqmp which sets the required clock for GEM controller Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * ARM64: zynqmp: Enable fastboot for first SD/MMC/EMMC deviceSiva Durga Prasad Paladugu2017-01-10-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DNL numbers are not changed that's why fastboot needs to be called with -i parameter (Xilinx vendor id). - Show available devices sudo fastboot -i 0x03fd devices xilinx_zynqmp_zcu100 fastboot - Stop fastboot and go back to U-Boot prompt sudo fastboot -i 0x03fd continue - Reboot the board sudo fastboot -i 0x03fd reboot - Get internal variables sudo fastboot -i 0x3fd getvar bootloader-version bootloader-version: U-Boot 2016.07-00026-g19bd53044817 sudo fastboot -i 0x3fd getvar downloadsize downloadsize: 0x06000000 sudo fastboot -i 0x3fd getvar version version: 0.4 (regular variables needs to have fastboot. prefix - there is also serialno variable which should be define as serial#) - Format SD/MMC/EMMC card sudo fastboot -i 0x3fd oem format - Write images to boot and Linux partition sudo fastboot -i 0x3fd flash boot sd.img sudo fastboot -i 0x3fd flash Linux os.img - Creating sd.img or os.img $ dd if=/dev/zero of=sd.img bs=1024 count=1024 $ mkfs.vfat sd.img $ mkdir sd-mount $ mount -o loop sd.img sd-mount $ echo foo > sd-mount/bar $ umount sd-mount partitions setting should be checked by running gpt command. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM64: zynqmp: Add idle state for ZynqMPStefan Krsmanovic2017-01-10-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0 idle state is added in this patch. References to the idle-states node are added in all CPU nodes. Time values: entry/exit latencies and min-residency, needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0 and Extended StateID format. Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com> Acked-by: Will Wong <willw@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM64: zynqmp: Fix usb nodes for dc1 and dc2Michal Simek2017-01-10-0/+8
| | | | | | | | | | | | | | Fix DT binding for usb nodes. Setup correct aliases and enable dwc3 nodes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM64: zynqmp: Add missing earlycon for ep108Michal Simek2017-01-10-0/+1
| | | | | | | | | | | | | | Just sync between version. Others zynqmp boards have this setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * ARM64: zynqmp: clk: Add the clock for watchdogShubhrajyoti Datta2017-01-10-0/+4
| | | | | | | | | | | | | | | | | | | | | | The watchdog clock node is missing. Add the same. This solves the below error. cdns-wdt fd4d0000.watchdog: input clock not found cdns-wdt: probe of fd4d0000.watchdog failed with error -2 Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source propertySudeep Holla2017-01-10-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: Setup modeboot variable based on boot modeMichal Simek2017-01-10-0/+6
| | | | | | | | | | | | | | modeboot variable is used for saving inforation which bootmode is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: Remove spi-max-frequencyMichal Simek2017-01-10-2/+0
| | | | | | | | | | | | | | spi-max-frequency for spi bus depends on devices which are connected to it. Remove this parameter from dtsi file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: Remove CONFIG_BOOTP_SERVERIPMichal Simek2017-01-10-1/+0
| | | | | | | | | | | | | | | | Do the same change which was done in ZynqMP by: "ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP" (sha1: a8b6a156c0f7fb99502229e454bc9c3b38645280) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: Move CONFIG_SYS_TEXT_BASE to KconfigMichal Simek2017-01-10-4/+14
| | | | | | | | | | | | Enable CONFIG_SYS_TEXT_BASE via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * fpga: zynqmp: Remove empty functionsMichal Simek2017-01-10-12/+0
| | | | | | | | | | | | | | Xilinx core files will take care about it. There is no need to have these functions because they do nothing. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM64: zynqmp: Add support to save env to FATSiva Durga Prasad Paladugu2017-01-10-0/+6
| | | | | | | | | | | | | | | | | | Add support to save environment as a file of FAT filesystem on to SD card. The file will be saved with name uEnv.txt. This environment will be retrieved during boot. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM64: zynqmp: Increase environment size to 32KSiva Durga Prasad Paladugu2017-01-10-1/+1
| | | | | | | | | | | | | | | | Increase environment size to 32K as the current default environment itself is greater than 4K. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * microblaze: Enable option to overwrite default variablesMichal Simek2017-01-10-0/+2
| | | | | | | | | | | | Enable overwriting variables out of main config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * microblaze: Remove hardcoded IP address from configMichal Simek2017-01-10-3/+0
| | | | | | | | | | | | | | IP addresses shouldn't be hardcoded in board config. This patch removes them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * microblaze: Make the board configuration name user definableSai Pavan Boddu2017-01-10-0/+5
| | | | | | | | | | | | | | Add a prompt for editing in menuconfig Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * net: gem: Use wait_for_bit() instead of private mdio_wait()Michal Simek2017-01-10-23/+9
| | | | | | | | | | | | | | Using generic wait_for_bit() implementation instead of using private wait function. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * lib: Add WATCHDOG_RESET to wait_bit.hMichal Simek2017-01-10-0/+2
| | | | | | | | | | | | | | | | wait_for_bit() is missing reset watchdog in case watchdog is configured. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: sunxi: remove bare default for CONFIG_MMCMasahiro Yamada2017-01-11-4/+0
| | | | | | | | | | | | | | | | The bare default entry is wrong. Just remove it since the (real) entry in drivers/mmc/Kconfig has "default ARM || PPC || SANDBOX". Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | mmc: move more driver config options to KconfigMasahiro Yamada2017-01-11-97/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move (and rename) the following CONFIG options to Kconfig: CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI) CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS) CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC) CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS) CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA) CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI) They are the same option names as used in Linux. This commit was created as follows: [1] Rename the options with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g ' [2] Commit the changes [3] Create entries in driver/mmc/Kconfig. (copied from Linux) [4] Move the options with the following command tools/moveconfig.py -y -r HEAD \ MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI [5] Sort and align drivers/mmc/Makefile for readability Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | ARM: davinci: remove unused CONFIG_DAVINCI_MMC_SD1Masahiro Yamada2017-01-11-2/+0
| | | | | | | | | | | | | | This CONFIG is not referenced from anywhere. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | mmc: move DesignWare-based drivers to KconfigMasahiro Yamada2017-01-11-11/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move (and rename) the following CONFIG options to Kconfig: CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS) CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3) CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA) The "HIKEY" is a board name, so it is not suitable for the MMC controller name. I am following the name used in Linux. This commit was generated as follows: [1] Rename the config options with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g ' [2] Commit the changes [3] Create the entries in drivers/mmc/Kconfig (with default y for EXYNOS and SOCFPGA) [4] Run the following: tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA [5] Sort and align drivers/mmc/Makefile for readability [6] Clean-up doc/README.socfpga by hand Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | mmc: move CONFIG_DWMMC to Kconfig, renaming to CONFIG_MMC_DWMasahiro Yamada2017-01-11-13/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit was created as follows: [1] Rename the option with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g' [2] create the entry for MMC_DW in drivers/mmc/Kconfig (the prompt and help were copied from Linux) [3] run "tools/moveconfig.py -y MMC_DW" [4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry [5] Clean-up doc/README.socfpga by hand Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | mmc: rename CONFIG_ROCKCHIP_DWMMC to CONFIG_MMC_DW_ROCKCHIPMasahiro Yamada2017-01-11-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | I am trying to make all DesignWare-based driver options prefixed with CONFIG_MMC_DW_. This commit was generated as follows: find . -name .git -prune -o -type f -print | \ xargs sed -i -e 's/ROCKCHIP_DWMMC/MMC_DW_ROCKCHIP/g' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | ARM: socfpga: remove unused CONFIG option and cleanup README.socfpgaMasahiro Yamada2017-01-11-27/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h, but not referenced at all. Remove. Also, clean-up the README.socfpga. CONFIG_MMC should not be defined in the header since it was moved to Kconfig by commit c27269953b94 ("mmc: complete unfinished move of CONFIG_MMC"). I see no grep hit for the others. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* | power: change from meaningless value to error numberJaehoon Chung2017-01-11-67/+64
| | | | | | | | | | | | | | | | '-1' is absolutely meaningless value. This patch changed from meaningless value to error number. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | mmc: uniphier-sd: fix Kconfig dependencyMasahiro Yamada2017-01-11-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some MMC drivers describe operations with the DM_MMC_OPS form, but there are still several drivers with older implementation. We can not compile drivers from different groups at the same time because the core framework is shared with #ifdef CONFIG_DM_MMC_OPS. Every driver should have "depends on DM_MMC_OPS" (or !DM_MMC_OPS) explicitly to express which framework it is based on. This will avoid enabling drivers with incompatible interface at the same time. It is incorrect to make a driver "select DM_MMC_OPS". While we are here, add "depends on OF_CONTROL" as well because this driver can be configured only by Device Tree. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit v1.1 at 2024-11-09 05:48:14 +0000