summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* kbuild: remove unused RANLIBMasahiro Yamada2014-06-05-1/+0
| | | | | | | RANLIB was added by commit e221174 (more than a decade ago) but it has been never referenced at all. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arm: fdt_control: fix a build error with CONFIG_OF_EMBED=yMasahiro Yamada2014-06-05-1/+1
| | | | | | | | | | | The build fails if a non-generic ARM board is compiled with CONFIG_OF_EMBED=y. The correct symbol name for embedded FDT is not __dtb_db_begin, but __dtb_dt_begin. (A typo introduced by commit 6ab6b2af) Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-arcTom Rini2014-06-05-0/+1
|\
| * ARC: enable CONFIG_SYS_BOOT_RAMDISK_HIGHAlexey Brodkin2014-06-03-0/+1
| | | | | | | | | | | | | | This enables relocation of initrd to the end of available DDR before Linux kernel start-up as it is done in other architectures. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-avr32Tom Rini2014-06-05-0/+1
|\ \ | |/ |/|
| * atngw100mkii: add missing CONFIG_SYS_TEXT_BASEAndreas Bießmann2014-05-26-0/+1
| | | | | | | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | powerpc: hiddendragon: remove orphan boardMasahiro Yamada2014-05-30-1096/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: debris: remove orphan boardMasahiro Yamada2014-05-30-1632/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: kvme080: remove orphan boardMasahiro Yamada2014-05-30-801/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: ep8248: remove orphan boardMasahiro Yamada2014-05-30-522/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: ispan: remove orphan boardMasahiro Yamada2014-05-30-791/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: rattler: remove orphan boardMasahiro Yamada2014-05-30-504/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: zpc1900: remove orphan boardMasahiro Yamada2014-05-30-558/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: mpc8260ads: remove orphan boardMasahiro Yamada2014-05-30-1616/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | powerpc: adder: remove orphan boardMasahiro Yamada2014-05-30-393/+1
| | | | | | | | | | | | | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC8xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* | PPC4xx: Remove quad100hd boardWolfgang Denk2014-05-30-425/+12
| | | | | | | | | | | | | | | | | | | | | | | | The quad100hd has been unmaintained and dead ever since it's been added some 6 years ago. Remove it. Also update README.scrapyard and insert some commit IDs for removed boards. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Gary Jennejohn <gljennjohn@googlemail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-05-30-54/+4112
|\ \
| * | ARM: at91sam9m10g45ek: add mmc environment configuration supportWu, Josh2014-05-27-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | In this configuration the environment will save in file: uboot.env of mmc card. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: at91sam9m10g45ek: enable mci0 supportWu, Josh2014-05-27-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also we enable the mmc command in configuration file. As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION, so remove the redundant CONFIG_DOS_PARTITION definition. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: at91: remove redundant ARM926EJS definition in board config filesWu, Josh2014-05-27-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | As at91 board config file will include the SoC header, so we can remove the ARM926EJS definition in board config files. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | at91: remove redundant AT91FAMILY definition in board config fileWu, Josh2014-05-27-10/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now the AT91FAMILY is already defined in the at91 SoC header. The at91 board config file will include the SoC header file. So we can remove the redundant AT91FAMILY definition in at91 board config files. Signed-off-by: Josh Wu <josh.wu@atmel.com> [rebase patch] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: at91sam9x5: define the AT91FAMILY and ARM926EJS in SoC headerWu, Josh2014-05-27-0/+3
| | | | | | | | | | | | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: at91: remove AT91X40 macro since it is not use any moreWu, Josh2014-05-27-2/+0
| | | | | | | | | | | | | | | | | | | | | The at91x40.h is not exist. So we remove it. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | sama5d3xek: enable PMECC header generationAndreas Bießmann2014-05-27-0/+1
| | | | | | | | | | | | | | | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Tested-by: Bo Shen <voice.shen@atmel.com>
| * | arm:at91: enable ROM loadable atmel imageAndreas Bießmann2014-05-27-0/+95
| | | | | | | | | | | | | | | | | | | | | | | | For sama5d3xek we need to modify the SPL image for correct detection by ROM code. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Tested-by: Bo Shen <voice.shen@atmel.com>
| * | mkimage: add atmelimageAndreas Bießmann2014-05-27-0/+348
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The new atmelimage converts a machine code BLOB to bootable ROM image. Atmel ROM has no sophisticated image format, it only checks the first 7 ARM vectors. The vectors can contain valid B or LDR opcodes, the 6'th vector contains the image size to load. Additionally the PMECC header can be written by the atmelimage target. The parameters must be given via the -n switch as a coma separated list. For example: mkimage -T atmelimage \ -n usePmecc=1,sectorPerPage=4,sectorSize=512,spareSize=64,eccBits=4,eccOffset=36 \ -d spl/u-boot-spl.bin boot.bin A provided image can be checked for correct header setup. It prints out the PMECC header parameters if it has one and the 6'th interrupt vector content. ---8<--- Image Type: ATMEL ROM-Boot Image with PMECC Header PMECC header ==================== eccOffset: 36 sectorSize: 512 eccBitReq: 4 spareSize: 64 nbSectorPerPage: 4 usePmecc: 1 ==================== 6'th vector has 17044 set --->8--- A SPL binary modified with the atmelimage mkimage target was succesfully booted on a sama5d34ek via MMC and NAND. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Heiko Schocher <hs@denx.de> Tested-by: Bo Shen <voice.shen@atmel.com>
| * | corvus: remove unneeded CONFIG_AT91_LEGACYAndreas Bießmann2014-05-27-1/+0
| | | | | | | | | | | | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Heiko Schocher <hs@denx.de>
| * | mmc: atmel_mci: fix print incorrect buffer content for debugWu, Josh2014-05-27-2/+3
| | | | | | | | | | | | | | | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> [fix checkpatch line length warning] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | gpio: at91: add sanity check for the NULL pointerWu, Josh2014-05-27-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need check the NULL pointer as at91_pio_get_port() may return NULL. Also print a error message when at91_pio_get_port() failed otherwise we cannot notice the failure. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: at91sam9x5ek: convert to generic boardBo Shen2014-05-27-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on boot: "Warning: Your board does not use generic board. Please read doc/README.generic-board and take action. Boards not upgraded by the late 2014 may break or be removed." Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: at91sam9m10g45ek: convert to generic boardBo Shen2014-05-27-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on boot: "Warning: Your board does not use generic board. Please read doc/README.generic-board and take action. Boards not upgraded by the late 2014 may break or be removed." Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: sama5d3_xplained: convert to generic boardBo Shen2014-05-27-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on boot: "Warning: Your board does not use generic board. Please read doc/README.generic-board and take action. Boards not upgraded by the late 2014 may break or be removed." Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: sama5d3xek: convert to generic boardBo Shen2014-05-27-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on boot: "Warning: Your board does not use generic board. Please read doc/README.generic-board and take action. Boards not upgraded by the late 2014 may break or be removed." Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: enable SPL on sama5d3_xplained boardBo Shen2014-05-27-0/+137
| | | | | | | | | | | | | | | | | | | | | It supports boot from NAND and SD/MMC card. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: switch to main crystal osc for SPL bootBo Shen2014-05-27-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | If without switch to main crystal oscillator, the sama5d3 SoC will use internal on chip RC oscillator. In order to get better accuracy, switch to main crystal oscillator. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | net/designware: Make DMA burst length configurable and reduce by defaultIan Campbell2014-05-25-7/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The correct value for this setting can vary across SoCs and boards, so make it configurable. Also reduce the default value to 8, which is the same default as used in the Linux driver. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Alexey Brodkin <abrodkin@synopsys.com>
| * | net/designware: reorder struct dw_eth_dev to pack more efficiently.Ian Campbell2014-05-25-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote: > The {r,t}xbuffs fields also need to be aligned. Previously this was done > implicitly because they immediately followed the descriptor tables. Make this > explicit and also move to the head of the struct. Looks like I managed to not actually commit the move of the field to the head of the struct! v3.1 follows.... Ian. 8<------------ >From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001 From: Ian Campbell <ijc@hellion.org.uk> Date: Thu, 1 May 2014 19:45:15 +0100 Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more efficiently. The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could be 256 or even larger. That means there is a potentially huge hole in the struct before those fields, so move them to the front where they are better packed. Moving them to the front also helps ensure that so long as dw_eth_dev is properly aligned (which it is since "net/designware: ensure device private data is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids having to worry too much about compiler specifics. The {r,t}xbuffs fields also need to be aligned. Previously this was done implicitly because they immediately followed the descriptor tables. Make this explicit and also move to the head of the struct. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Alexey Brodkin <abrodkin@synopsys.com> Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
| * | net/designware: ensure cache invalidations are aligned to ARCH_DMA_MINALIGNIan Campbell2014-05-25-5/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is required at least on ARM. When sending instead of simply invalidating the entire descriptor, flush as little as possible while still respecting ARCH_DMA_MINALIGN, as requested by Alexey. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Alexey Brodkin <abrodkin@synopsys.com>
| * | net/designware: ensure device private data is DMA aligned.Ian Campbell2014-05-25-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | struct dw_eth_dev contains fields which are accessed via DMA, so make sure it is aligned to a dma boundary. Without this I see: ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0 Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com> Acked-by: Marek Vasut <marex@denx.de>
| * | sunxi: non-FEL SPL boot support for sun7iIan Campbell2014-05-25-0/+255
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for booting from an MMC card. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | sunxi: mmc supportIan Campbell2014-05-25-0/+702
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote: > > + case 1: > > +#if CONFIG_MMC1_PG > Are you sure that this is correct and shouldn't be: > > +#ifdef CONFIG_MMC1_PG > > ? It's "correct" in so far as it works (the boards.cfg config stuff #defines things to 1), but I think you are right that it isn't the preferred style. But... > A quick scan through this patch series shows that this define > is not set at all. Perhaps its outdated? Or is it used to support > some other sunxi SoC? Not sure, perhaps it should be removed for > now. ...I had thought that it was to support some other board which wasn't being upstreamed right now, so eventually useful and harmless for now, but I've just checked and it isn't actually used by any of the boards in u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it. Rather than resend the entire series, here is v5.1 of this patch. > Other than this please add my: > > Reviewed-by: Stefan Roese <sr@denx.de> Thanks! 8<--------------------------------- >From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001 From: Ian Campbell <ijc@hellion.org.uk> Date: Fri, 7 Mar 2014 04:29:39 +0000 Subject: [PATCH v5.1 7/8] sunxi: mmc support This adds support for the MMC controller on the Allwinner A20 (sun7i) processor. Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Cc: Aaron Maoye <leafy.myeh@allwinnertech.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | sunxi: add gmac Ethernet supportIan Campbell2014-05-25-1/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i) processors. Enable for the Cubietruck. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
| * | sunxi: add support for Cubietruck booting in FEL modeIan Campbell2014-05-25-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com> Reviewed-by: Marek Vasut <marex@denx.de>
| * | sunxi: add sun7i cpu, board and start of day supportIan Campbell2014-05-25-1/+572
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds generic board, start of day and basic build system support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Adam Sampson <ats@offog.org> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luc Verhaegen <libv@skynet.be> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Patrick Wood <patrickhwood@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | sunxi: add sun7i dram setup supportIan Campbell2014-05-25-0/+773
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds DRAM initialisation support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | sunxi: add sun7i pinmux and gpio supportIan Campbell2014-05-25-0/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ma Haijun <mahaijuns@gmail.com> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | sunxi: add sun7i clocks and timer support.Ian Campbell2014-05-25-0/+727
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the basic clocks and timer support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Some of the code here is common to multiple sunxi subarchtectures, hence files are named sun4i which is the earliest similar variant. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | boards.cfg: update highbank maintainer emailRob Herring2014-05-25-1/+1
| | | | | | | | | | | | | | | | | | My Calxeda email is gone, so update my email address. Signed-off-by: Rob Herring <robh@kernel.org>
| * | arm: vf610: add DDR_SEL_PAD_CONTR registerStefan Agner2014-05-25-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM issues with newer silicon (1.1). This register was added in revision 4 of the Vybrid Reference Manual. Signed-off-by: Stefan Agner <stefan@agner.ch>
| * | Arm64 fix a bug of vbar_el3 initializationDavid Feng2014-05-25-2/+2
| | | | | | | | | | | | Signed-off-by: David Feng <fenghua@phytium.com.cn>
generated by cgit v1.1 at 2024-11-09 05:44:11 +0000