summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
| * powerpc/85xx: Optimized DDR settings for 800MT/s on P1/P2 RDBPoonam Aggrwal2011-04-04-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | Changed the following DDR timing parameters for 800Mt/s: tRRT BL/2+1 to BL/2 tWWT BL/2+1 to BL/2 tWRT BL/2+1 to BL/2 tRWT BL/2+1 to BL/2 REFINT 6500ns to 7800ns Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Removed P1/P2 RDB RevB supportPoonam Aggrwal2011-04-04-22/+7
| | | | | | | | | | | | | | | | RevB boards never really made it outside of Freescale and have been replaced with RevC & RevD which had various board bug fixes. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Read board switch settings on p1_p2_rdbPriyanka Jain2011-04-04-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PCA9557 is parallel I/O expansion device on I2C bus which stores various board switch settings like NOR Flash-Bank selection, SD Data width. On board: switch SW5[6] is to select width for eSDHC ON - 4-bit [Enable eSPI] OFF - 8-bit [Disable eSPI] switch SW4[8] is to select NOR Flash Bank for Booting OFF - Primary Bank ON - Secondary Bank Read board switch settings on p1_p2_rdb and configure corresponding eSDHC width. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Use DDR for RAMBOOT instead of L2 SRAM on p1_p2_rdbPriyanka Jain2011-04-04-17/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using DDR as RAMBOOT base instead of L2SRAM for SDCard and SPI Flash boot loaders because: - P1_P2_RDB boards have soldered DDR so no need for SPD - Also P102x has 256K L2 cache size so becomes a limiting factor for size of image that could be loaded in SRAM mode and would require three stage boot loader (TPL). Changes done: 1. CONFIG_SYS_TEXT_BASE to 0x11000000 2. CONFIG_RESET_VECTOR_ADDRESS to 0x1107fffc Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * fsl: obsolete NXID v0 EEPROMs, automatically upgrade them to NXID v1Timur Tabi2011-04-04-10/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The NXID EEPROM format comes in two versions, v0 and v1. The only difference is in the number of MAC addresses that can be stored. NXID v0 supports eight addresses, and NXID v1 supports 23. Rather than allow a board to choose which version to support, NXID v0 is now considered deprecated. The EEPROM code is updated to support only NXID v1, but it can still read EEPROMs formatted with v0. In these cases, the EEPROM data is loaded and the CRC is verified, but the data is stored into a v1 data structure. If the EEPROM data is written back, it is written in v1 format. This allows existing v0-formatted EEPROMs to continue providing MAC addresses, but any changes to the data will force an upgrade to the v1 format, while retaining all data. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Specify CONFIG_SYS_FM_MURAM_SIZEKumar Gala2011-04-04-0/+8
| | | | | | | | | | | | | | CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in config_mpc85xx.h for those parts with a Frame Manager. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Corrected sdhc clock value for P1010Priyanka Jain2011-04-04-1/+2
| | | | | | | | | | | | | | | | SDHC clock is equal to CCB on P1010 and P1014 not CCB/2. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Adds some P1010/P1014 SoC configuration definesPoonam Aggrwal2011-04-04-0/+8
| | | | | | | | | | | | | | | | Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR and SDHC erratum. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Support for Freescale P1024/P1025 processorKumar Gala2011-04-04-0/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Support for Freescale P1024/P1025 (dual core) and P1015/P1016 (single core) processors. P1024 is a variant of P1020 processor with a core frequency from 400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA P1025 is a variant of P1021 processor with a core frequency from 400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA P1015 is a variant of P1024 processor with single core and P1016 is a variant of P1025 processor with single core. Added comments in config_mpc85xx.h to denote single core versions of processors. Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * echi: add ULI1575 PCI IDZhao Chenhui2011-04-04-0/+1
| | | | | | | | | | | | | | | | Add ULI1575 EHCI controller to the list of the supported devices. Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: load ucode from nand flash before qe_initHaiying Wang2011-04-04-0/+17
| | | | | | | | | | | | | | | | In the case the QE's microcode is stored in nand flash, we need to load it from NAND flash to ddr first then the qe_init can get the ucode correctly. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * fsl_ddr: Adds 16 bit DDR Data width optionPoonam Aggrwal2011-04-04-1/+4
| | | | | | | | | | | | Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Use BR_PHYS_ADDR macro to setup BRs on P1_P2_RDBPoonam Aggrwal2011-04-04-2/+3
| | | | | | | | | | Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/8xxx: Display DIMM modelYork Sun2011-04-04-4/+7
| | | | | | | | | | | | | | | | Beside displaying RDIMM or UDIMM, this patch adds display of the model numbers embedded in SPD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Update fixed DDR3 timing table for P4080DSYork Sun2011-04-04-8/+8
| | | | | | | | | | | | | | | | | | Most of time U-boot doesn't get an exact clock number. For example, clock 900MHz may be detected as 899.99MHz. 800MHz could be 799.99MHz. Update the table to align the desired clocks in the middle. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/8xxx: Fix LAW init to respect pre-initialized entriesKumar Gala2011-04-04-0/+20
| | | | | | | | | | | | | | | | | | | | If some pre-boot or earlier stage bootloader (NAND SPL) has setup LAW entries consider them good and mark them used. In the NAND SPL case we skip re-initializing based on the law_table since the SPL phase already did that. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * fsl_pci: Add support for FSL PCIe controllers v2.xPrabhakar Kushwaha2011-04-04-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FSL PCIe controller v2.1: - New MSI inbound window - Same Inbound windows address as PCIe controller v1.x Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window FSL PCIe controller v2.2 and v2.3: - Different addresses for PCIe inbound window 3,2,1 - Exposed PCIe inbound window 0 - New PCIe interrupt status register Added new Interrupt Status register to struct ccsr_pci & updated pit_t array size to reflect the 4 inbound windows. To maintain backward compatiblilty, on V2.2 or greater controllers we start with inbound window 1 and leave inbound 0 with its default value (which maps to CCSRBAR). Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Refactor Qman/Portal support to be shared between SoCsHaiying Wang2011-04-04-22/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | There are some differences between CoreNet (P2040, P3041, P5020, P4080) and and non-CoreNet (P1017, P1023) based SoCs in what features exist and the memory maps. * Rename various immap defines to remove _CORENET_ if they are shared * Added P1023/P1017 specific memory offsets * Only setup LIODNs or LIODN related code on CORENET based SoCs (features doesn't exist on P1023/P1017) Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add support for Freescale P1023/P1017 ProcessorsRoy Zang2011-04-04-1/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | Add P1023 (dual core) & P1017 (single core) specific information: * SERDES Table * Added P1023/P1017 to cpu_type_list and SVR list (fixed issue with P1013 not being sorted correctly). * Added P1023/P1027 to config_mpc85xx.h * Added new LAW type introduced on P1023/P1017 * Updated a few immap register/defines unique to P1023/P1017 Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Don't build read_tlbcam_entry for CONFIG_NAND_SPLKumar Gala2011-04-04-2/+2
| | | | | | | | | | | | Slim down NAND SPL build a bit as we don't need read_tlbcam_entry. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc: Add cpu_secondary_init_r to allow for initialization post env setupKumar Gala2011-04-04-6/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | We can simplify some cpu/SoC level initialization by moving it to be after the environment and non-volatile storage is setup as there might be dependancies on such things in various boot configurations. For example for FSL SoC's with QE if we boot from NAND we need it setup to extra the ucode image to initialize the QE. If we always do this after environment & non-volatile storage is working we can have the code be the same regardless of NOR, NAND, SPI, MMC boot. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Cleanup some QE related definesKumar Gala2011-04-04-67/+37
| | | | | | | | | | | | | | | | | | Move some processor specific QE defines into config_mpc85xx.h and use QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct. Also fixed up some comment style issues in immap_qe.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/8xxx: Refactor fsl_ddr_get_spd into common code from boardKumar Gala2011-04-04-551/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards pretty much do the same thing. The only variations are in how many controllers or DIMMs per controller exist. To make this work we standardize on the names of the SPD_EEPROM_ADDRESS defines based on the use case of the board. We allow boards to override get_spd to either do board specific fixups to the SPD data or deal with any unique behavior of how the SPD eeproms are wired up. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/8xxx: Replace fsl_ddr_get_mem_data_rate with get_ddr_freq()Kumar Gala2011-04-04-150/+9
| | | | | | | | | | | | | | | | | | | | Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq() and every 86xx board uses get_bus_freq(). If implement get_ddr_freq() as a static inline to call get_bus_freq() we can remove fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq() directly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Remove config.mk for nand linker scriptKumar Gala2011-04-04-121/+4
| | | | | | | | | | | | | | Move the include of mpc85xx/u-boot-nand.lds to utilize CONFIG_SYS_LDSCRIPT rather than having an explicit config.mk Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc: Move cpu specific lmb reserve to arch_lmb_reserveKumar Gala2011-04-04-93/+10
| | | | | | | | | | | | | | | | We've been utilizing board_lmb_reserve to reserve the boot page for MP systems. We can just move this into arch_lmb_reserve for 85xx & 86xx systems rather than duplicating in each board port. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Update P2020DS default env settingsLi Yang2011-04-04-10/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Read MAC address from EEPROM. Add hwconfig settings. Modified the default othbootargs to include the cache-sram-size parameter. This parameter is needed as the L2 as SRAM is ON by default in the P2020RDB kernel and used by the Gianfar driver. Also cleanup some of the boot commands. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add eSDHC support on P2020DSJerry Huang2011-04-04-1/+37
| | | | | | | | | | | | | | | | | | | | | | We enable SDHC_CD and SDHC_WP signals (pin muxed with GPIO8 & GPIO9 respectively). We enable EXT2, FAT, and parition support for both MMC & USB configs. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add some defines for P2040, P3041, P5010, P5020Kumar Gala2011-04-04-0/+15
| | | | | | | | | | | | | | Specify the number of DDR controllers, number of frame managers, number of 1g and 10g ports. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Extend ethernet device tree stashing parameters for "fsl,etsec2"Pankaj Chauhan2011-04-04-0/+3
| | | | | | | | | | | | | | | | | | In a manner similar to passing ethernet stashing parameters into device tree for "gianfar", extend the support to the "fsl,etsec2" as well. Signed-off-by: Pankaj Chauhan <pankaj.chauhan@freescale.com> Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Declare fsl_ddr_set_memctl_regs in <asm/fsl_ddr_sdram.h>Kumar Gala2011-04-04-6/+2
| | | | | | | | | | | | | | | | | | Remove declerations of fsl_ddr_set_memctl_regs in board files with and place it into a common header. Based on patch from Poonam Aggrwal. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Remove DATARATE_*_MHZ defines in static ddr initKumar Gala2011-04-04-35/+28
| | | | | | | | | | | | | | | | | | | | Rather than having #defines DATARATE_*_MHZ, lets just match what we do on the SPD code and convert the DDR frequency into MHZ and just compare with a constant. Based on patch from Poonam Aggrwal. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * p1022ds: allow for board-specific ngPIXIS functionsTimur Tabi2011-04-04-18/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ngPIXIS is an FPGA used on the reference boards of most Freescale PowerPC SOCs. Although programming the ngPIXIS is mostly standard on all boards that have it, the P1022DS is unique in that the ngPIXIS needs to be programmed in "indirect" mode whenever the video display (DIU) is active. To support indirect mode, and to make it easier to support other quirks on future reference boards, the low-level ngPIXIS functions are all marked as weak, so that board-specific code can override any of them. We take advantage of this feature on the P1022DS, so that we can properly reset the board when the DIU is active. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add support for Integrated Flash Controller (IFC)Dipen Dudhat2011-04-04-2/+1056
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Integrated Flash Controller (IFC) is used to access the external NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip selects are provided in IFC so that maximum of four Flash devices can be hooked, but only one can be accessed at a given time. Features supported by IFC are, - Functional muxing of pins between NAND, NOR and GPCM - Support memory banks of size 64KByte to 4 GBytes - Write protection capability (only for NAND and NOR) - Provision of Software Reset - Flexible Timing programmability for every chip select - NAND Machine - x8/ x16 NAND Flash Interface - SLC and MLC NAND Flash devices support with configurable page sizes of upto 4KB - Internal SRAM of 9KB which is directly mapped and availble at boot time for NAND Boot - Configurable block size - Boot chip select (CS0) available at system reset - NOR Machine - Data bus width of 8/16/32 - Compatible with asynchronous NOR Flash - Directly memory mapped - Supports address data multiplexed (ADM) NOR device - Boot chip select (CS0) available at system reset - GPCM Machine (NORMAL GPCM Mode) - Support for x8/16/32 bit device - Compatible with general purpose addressable device e.g. SRAM, ROM - External clock is supported with programmable division ratio - GPCM Machine (Generic ASIC Mode) - Support for x8/16/32 bit device - Address and Data are shared on I/O bus - Following Address and Data sequences can be supported on I/O bus - 32 bit I/O: AD - 16 bit I/O: AADD - 8 bit I/O : AAAADDDD - Configurable Even/Odd Parity on Address/Data bus supported Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add SERDES support for P1010/P1014Prabhakar Kushwaha2011-04-04-0/+82
| | | | | | | | | | | | | | | | | | | | | | Add the ability to determine if a given IP block connected on SERDES is configured. This is useful for things like PCIe and SRIO since they are only ever connected on SERDES. Updated MPC85xx_PORDEVSR_IO_SEL & MPC85xx_PORDEVSR_IO_SEL_SHIFT Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-mipsWolfgang Denk2011-04-05-1617/+113
|\ \
| * | MIPS: Au1x00: Move all Au1x00 specific code to separate subdirectoryDaniel Schwierzeck2011-04-02-9/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | Au1x00 is a SoC and its specific code should reside in an own SoC subdirectory. Also add -mtune=4kc flag for CPU optimization. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Thomas Lange <thomas@corelatus.se> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | MIPS: IncaIP: Move all IncaIP specific code to separate subdirectoryDaniel Schwierzeck2011-04-02-6/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | IncaIP is a SoC and its specific code should reside in an own SoC subdirectory. Also add -mtune=4kc flag for CPU optimization. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | MIPS: Optimize the setup of CPU optimization flagsDaniel Schwierzeck2011-04-02-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current MIPS CPU config.mk code always expects a MIPS 4kc core. This is not appropiate for other CPUs and SoCs. Replace the current MIPSFLAGS code by cc-option macro and use -march=mips32r2 as default optimization level for all MIPS32 CPUs. Note: Since commit f62fb99941c625605aa16a0097b396a5c16d2c88 all toolchains with binutils prior to v2.16 are not working anymore. As agreed with Shinya Kuribayashi the support for those toolchains will be dropped officially with this patch. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | MIPS: Move content of arch/mips/cpu to arch/mips/cpu/mips32Daniel Schwierzeck2011-04-02-25/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All current CPUs and SoCs are based on MIPS32 arch. The complete code resides in the global arch/mips/cpu directory. This is not suitable if other MIPS architectures like MIPS64 or Octeon should be supported in the future. To achieve this the current CPU code is moved to its own mips32 subdirectory. All MIPS32 boards have to use mips32 as config switch in board.cfg. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Lange <thomas@corelatus.se> Cc: Vlad Lungu <vlad.lungu@windriver.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * | MIPS: Purple: Remove Purple supportDaniel Schwierzeck2011-04-02-1641/+1
| |/ | | | | | | | | | | | | | | The Purple SoC and eval board are not actively maintained since years. This patch removes the support completely as aggreed with Wolfgang Denk. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
* | ehci-pci: Add PCI EHCI controllerTrübenbach, Ralf2011-04-02-1/+2
| | | | | | | | | | | | | | | | | | | | This patch adds support for the PI7C9X442SL PCIe EHCI host controller from Pericom. Tested at P4080DS eval board from Freescale. Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de> Cc: Remy Bohmer <linux@bohmer.net>
* | fat32 root directory handlingErik Hansen2011-04-02-14/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fat directory handling didn't check reaching the end of the root directory. It relied on a stop condition based on a directory entry with a name starting with a '\0' character. This check in itself is wrong ('\0' indicates free entry, not end_of_directory) but outside the scope of this fix. For FAT32, the end of the rootdir is reached when the end of the cluster chain is reached. The code didn't check this condition and started to read an incorrect cluster. This caused a subsequent read request of a sector outside the range of the usb stick in use. On its turn, the usb stick protested with a stall handshake. Both FAT32 and non-FAT32 (FAT16/FAT12) end or rootdir checks have been put in. Signed-off-by: Erik Hansen <erik@makarta.com>
* | Remove unnecessary reset in usb_stor_get_infoErik Hansen2011-04-02-25/+0
| | | | | | | | | | | | | | | | The reset request in usb_stor_get_info is causing issues with some usb sticks. Some of these sticks vendor_id/product_id have been hardcoded to not reset but better is to remove the reset altogether. It is not needed. Signed-off-by: Erik Hansen <erik@makarta.com>
* | usb: musb: blackfin: check anomaly workarounds at runtime tooMike Frysinger2011-04-02-3/+26
| | | | | | | | | | | | | | | | The anomaly workarounds we need for older silicon might break things if used on newer versions where the anomalies don't exist. So check the silicon rev at runtime too. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | usb: musb: blackfin: make clkin configurableMike Frysinger2011-04-02-1/+6
|/ | | | | | Not everyone has a 24MHz clkin to the USB, so let board porters override. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* atmel_nand: don't require CONFIG_SYS_NAND_ENABLE_PINmichael2011-04-01-0/+2
| | | | | | | | | | | | If NCE is hooked up to NCS3, we don't need to (and can't) explicitly set the state of the NCE pin. Instead, the controller asserts it automatically as part of a command/data access. Only "CE don't care"-type NAND chips can be used in this manner. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
* NAND: add support for reading ONFI page tableFlorian Fainelli2011-04-01-49/+213
| | | | | | | | | | | | This patch adds support for reading an ONFI page parameter from a NAND device supporting it. If this is the case, struct nand_chip onfi_version member contains the supported ONFI version, 0 otherwise. This allows NAND drivers past nand_scan_ident to set the best timings for the NAND chip. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
* Fix NAND_SPL and ONENAND_IPL in MakefileHaiying Wang2011-04-01-16/+14
| | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* NAND: add more watchdog resetsScott Wood2011-04-01-0/+8
| | | | | | | Poke the watchdog in a variety of looping constructs, which could take a long time to complete. Signed-off-by: Scott Wood <scottwood@freescale.com>
generated by cgit v1.1 at 2024-11-05 06:56:11 +0000