summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ARM: Add support for jadecpu board based on MB86R01 SoCMatthias Weisser2010-08-10-0/+791
| | | | | | | This patch adds support for the jadecpu board using the MB86R01 'Jade' SoC from Fujitsu. Signed-off-by: Matthias Weisser <weisserm@arcor.de>
* video: add support for display controller in MB86R0x SoCsMatthias Weisser2010-08-10-0/+187
| | | | | | | | This patch adds support for the display controller in the MB86R0x SoCs. Signed-off-by: Matthias Weisser <weisserm@arcor.de> Acked-by: Anatolij Gustschin <agust@denx.de>
* ARM: Add support for MB86R0x SoCsMatthias Weisser2010-08-10-6/+956
| | | | Signed-off-by: Matthias Weisser <weisserm@arcor.de>
* Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-08-10-2/+2
|\
| * MX51EVK: fix return value of get_timer_maskedLi Haibo2010-08-10-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | get_timer_masked() should return current timestamp, not current ticks from hardware register. Tested on one custom board with NAND flash. Without this patch, NAND write always TIMEOUT because get_timer(0) return a big value. This patch applies for u-boot-2010.06 Signed-off-by: Li Haibo <hbli@sinocastel.com>
| * fix cmd_mmc.c, line 136 missing "Reinhard Meyer2010-08-10-1/+1
| | | | | | | | | | | | Remove warning for missing " at the end of line 136 Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* | orion5x: allow overriding default mappings windowsAlbert Aribaud2010-08-10-41/+97
| | | | | | | | | | | | | | | | | | | | Turn all ORION5X_DEF{ADR,SZ}_xxx macros into ORION5X_{ADR,SZ}_xxx and allow defining them from board code to override defaults. This is particularly useful for defining board-specific FLASH address and size in board header file rather than having to tweak orion5x code. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* | Merge branch 'master' of git://git.denx.de/u-boot-marvellWolfgang Denk2010-08-10-13/+247
|\ \
| * | Kirkwood: openrd_base: Added SATA supportPrafulla Wadaskar2010-08-08-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | This patch enables mvsata driver and related filesystem support. The patch is tested for ide reset and ext2ls operation for a disk drive connected on SATA port0. This patch depends upon the patche-series http://lists.denx.de/pipermail/u-boot/2010-August/074908.html Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * | cmd_ide: add support for KirkwoodPrafulla Wadaskar2010-08-08-0/+7
| | | | | | | | | | | | | | | | | | | | | Added MVSATAC definitions to Kirkwood. Added support for Kirkwood in cmd_ide. Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * | edminiv2: add mvsata_ide and cmd_ide supportAlbert Aribaud2010-08-08-1/+33
| | | | | | | | | | | | | | | | | | Add mvsata_ide and cmd_ide configuration in edminiv2 config Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| * | cmd_ide: add support for orion5xAlbert Aribaud2010-08-08-0/+8
| | | | | | | | | | | | | | | | | | | | | Add MVSATAHC definitions to orion5x. Add support for orion5x in cmd_ide. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| * | ide: add mvsata_ide driverAlbert Aribaud2010-08-08-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | This driver only provides initialization code; actual driving is done by cmd_ide.c using the ATA compatibility mode of the Marvell SATAHC controller. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| * | ide: reorder object files alphabeticallyAlbert Aribaud2010-08-08-3/+3
| | | | | | | | | | | | Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| * | ide: add configurationAlbert Aribaud2010-08-08-9/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_IDE_SWAP_IO This configuration option replaces a complex conditional in cmd_ide.c with an explicit define to be added to SoC or board configs. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* | | Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk2010-08-10-25/+1210
|\ \ \
| * | | ARMV7: Update default environment for OMAP4 boardsSteve Sakoman2010-08-05-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specify vram on command line, remove erroneous call to nandboot in the boot script, add CONFIG_BOOTDELAY Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Nishanth Menon <menon.nishanth@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Enable musb driver and usbtty on OMAP4 PandaSteve Sakoman2010-08-05-0/+15
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Enable musb driver and usbtty on OMAP4430 SDPSteve Sakoman2010-08-05-0/+15
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Restructure omap3 musb driver to allow code sharing between OMAP3 and ↵Steve Sakoman2010-08-05-1/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | OMAP4 Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Add support for the TWL6030 I2C power chip used in OMAP4 systemsSteve Sakoman2010-08-05-0/+176
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add the basic infrastructure for the TWL6030 driver and enables support in the two existing OMAP4 boards, Panda and OMAP4430 SDP Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Modify i2c driver for more reliable operation on OMAP4Steve Sakoman2010-08-05-11/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch modifies the init routine to follow the TRM recommendations. It also modifies the i2c_read_byte function to reflect subtle differences between the i2c controller in OMAP3 and OMAP4. Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Nishanth Menon <menon.nishanth@gmail.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Fix udelay for OMAP4Steve Sakoman2010-08-05-11/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The OMAP4 x-load code sets gptimer1 clock source to 32Khz. This isn't acceptable for udelay. This patch changes from gptimer1 to gptimer2, which uses sys_clk at 38.4 Mhz. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Add pad mux support for OMAP4Steve Sakoman2010-08-05-0/+942
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | Add functional multiplexing support for OMAP4 pads. Configure all the pads for the OMAP4430 SDP and OMAP4 Panda boards Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | | Merge branch 'master' of ../masterWolfgang Denk2010-08-10-866/+683
|\ \ \ | | |/ | |/|
| * | PXA: Declare __io for vpac270 IDEMarek Vasut2010-08-09-0/+2
| | | | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
| * | PXA: Fix missing includesMarek Vasut2010-08-09-0/+2
| | | | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
| * | PXA: Fix off-the-tree build problemsMarek Vasut2010-08-09-16/+24
| | | | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
| * | config.mk: avoid -traditional-cpp on OS X 10.5Mike Frysinger2010-08-09-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Simply trying to include a basic header file like stdlib.h on OS X 10.5 and then building with -traditional-cpp fails with lots of errors like: In file included from /usr/include/stdlib.h:63, from test.c:3: /usr/include/available.h:85: error: stray '#' in program /usr/include/available.h:85: error: syntax error before numeric constant /usr/include/available.h:86: error: stray '#' in program In the past, I hadn't noticed because the old logic for these flags were restricted to Darwin running on PowerPC systems while I'm running on an Intel system. But after some recent clean ups and changes, the flag was being applied to all Darwin systems and my host tools broke. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | fdt: Fix bug in size calculation in fdt_resize() with initrd useFeng Wang2010-08-09-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Original bug description from Feng (fdt_resize() bug caused "WARNING: could not set linux, initrd-start FDT_ERR_NOSPACE."): What I got is an error: "WARNING: could not set linux,initrd-start FDT_ERR_NOSPACE." after loading Device Tree blob. This in turn caused linux to miss init part. After some digging, I found out the reason for this error, it is caused by fdt_resize(). FDT blob got resized after filling in all board specific information of PowerPC. (in boot_body_linux()). It reduced blob size with only extra space for two fdt_reserve_entry, one for fdt itself, and one for initrd. Then it's aligned to a 0x1000 page boundary. However, later in fdt_initrd(), it could add two more properties, initrd-start AND initrd-end, each one needs at least two fdt_reserve_entry sizes done by _fdt_add_property() (name and value). Thus, the two fdt_reserve_entry extra space is not sufficient. So for some specific fdt size which is just under the page boundary after resizing, this will cause an error of FDT_ERR_NOSPACE in fdt_initrd() when setting those two properties, and failed to pass initrd information to linux. My fix is in fdt_resize(), leave at least 4 fdt_reserve_entry for initrd. So instead of 2*sizeof(struct fdt_reserve_entry) for actual_totalsize, use 5*sizeof(struc fdt_reserve_entry). Stefan: I got this same error on katmai, when trying to boot with initrd (run flash_self). This patch fixes this issue. Signed-off-by: Feng Wang <fwang02@harris.com> Tested-by: Stefan Roese <sr@denx.de> Cc: Jerry Van Baren <gvb.uboot@gmail.com> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
| * | board/purple/flash.c: removed unneded variableFrans Meulenbroeks2010-08-09-3/+2
| | | | | | | | | | | | | | | | | | removed a variable that was not used Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
| * | various cmd_* files: fixed layout a little bitFrans Meulenbroeks2010-08-09-13/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Most of the files have U_BOOT_CMD on a separate line, but a few didn't and had the first line on the same line as U_BOOT_CMD. This changes these files by adding a line break and a tab Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
| * | various cmd_* files: remove the command name from the help messageFrans Meulenbroeks2010-08-09-5/+7
| | | | | | | | | | | | | | | | | | | | | removed the command name from the help message as it is already printed. for cmd_mmc also rewrote the message a little bit Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
| * | tools/env/fw_printenv: Make redundant env work on locked flashes alsoDetlev Zundel2010-08-09-1/+6
| | | | | | | | | | | | | | | | | | | | | The invalidation of the old environment instance did not work for flashes supporting hardware locking. Now we unlock/lock around this update also. Signed-off-by: Detlev Zundel <dzu@denx.de>
| * | flash_protect: check for NULL flash infoMike Frysinger2010-08-09-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a flash is unable to be detected, and then someone calls flash_protect on it (like the common code does in flash_init), the flash_protect logic will dereference a NULL pointer. Since flash_protect already does sanity checking on the info structs, add a NULL pointer check in there. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | getenv_f(): fix handling of too short buffersWolfgang Denk2010-08-09-6/+12
| | | | | | | | | | | | | | | | | | | | | | | | Fix error handling in getenv_f() when the user provided buffer is too short to hold the variable name; make sure to truncate and NUL-terminate without overwriting the buffer limits. Signed-off-by: Wolfgang Denk <wd@denx.de>
| * | dataflash mmc mux: use common cmd_usage functionMike Frysinger2010-08-09-2/+1
| | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | mflash: use common cmd_usage functionMike Frysinger2010-08-09-2/+1
| | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | print_buffer: optimize & shrinkMike Frysinger2010-08-09-14/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Applying a little creative format string allows us to shrink the initial data read & display loop by only calling printf once. Re-using the local data buffer to generate the string we want to display then allows us to output everything with just one printf call instead of multiple calls to the putc function. The local stack buffer needs increasing by 1 byte, but the resulting code shrink and speed up is worth it I think. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | cmd editing: optimize/shrink output blankingMike Frysinger2010-08-09-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | No need to output spaces 1 char at a time in a loop when the printf code can do the same thing with the right format string. This shrinks things and gives a nice speed up when killing off lines more than a byte or two as printf will send out the buffer in one big chunk. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | 8xx, kup4k/kup4x: add FDT supportHeiko Schocher2010-08-09-0/+15
| | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
| * | 8xx, kup4k/kup4x: configuration changes, code cleanupHeiko Schocher2010-08-09-784/+427
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - nfs-options removed - hda->sda changed - mtd parts added - loadaddress changed - cmd-line length increased - lcd stuff removed - code cleanup (use I/O accessors etc.) Signed-off-by: Klaus Heydeck <heydeck@kieback-peter.de>
| * | fdt relocate: have more attention to use a bootmap or notStephan Linz2010-08-08-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Platforms with flat device tree support can use a bootmap to relocate the fdt_blob. This is not a must. That's why the relocation function boot_relocate_fdt() should be use only if CONFIG_OF_LIBFDT was defined together with CONFIG_SYS_BOOTMAPSZ (see common/cmd_bootm.c). On MicroBlaze platforms there is no need to use a bootmap to relocate a fdt blob. So we need a more precise focus on the compilation and usage of boot_relocate_fdt(). In general it is valid to exclude the function boot_relocate_fdt() if the bootmap size CONFIG_SYS_BOOTMAPSZ is not defined. Signed-off-by: Stephan Linz <linz@li-pro.net>
| * | Add mkimage manpageNobuhiro Iwamatsu2010-08-08-0/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some Linux distributions include the "mkimage" as a package. This commit provides a manual page for mkimage. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Added documentation for FIT images and examples. Moved to doc/ directory. Signed-off-by: Wolfgang Denk <wd@denx.de>
| * | LZMA and LZO causes compile errorMatthias Weisser2010-08-07-2/+5
| | | | | | | | | | | | | | | | | | | | | If both LZMA and LZO compressions are used there is a compile error in cmd_bootm.c Signed-off-by: Matthias Weisser <weisserm@arcor.de>
| * | ext2fs: Fix optimization bug for doubly-indirect block pointersAaron Pace2010-08-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Doubly-indirect block numbers are compared against the first-level indirect block when checking for a cached copy. This is causing the doubly-indirect block to be re-read each time it is accessed. Repairing this reduces load time for a 70M file from 72 seconds to 38 seconds. Signed-off-by: Aaron Pace <Aaron.Pace@alcatel-lucent.com>
* | | ARM: Define __raw_readX and __raw_writeXMarek Vasut2010-08-07-6/+40
| | | | | | | | | | | | | | | | | | | | | These functions are undefined on ARM when using __io. These are the commonly used versions and can be redefined. Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
* | | Merge branch 'master' of /home/wd/git/u-boot/masterWolfgang Denk2010-08-07-95109/+4121
|\ \ \ | |/ / | | / | |/ |/|
| * Fix condition where bootm_size not set and wrong memory size reportedMatthew McClintock2010-08-07-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | If the user sets bootm_low and does not set bootm_size, u-boot will report the memory node in the flat device tree incorrectly. Instead of reporting the remaining size of memory, it will report the total available memory which is incorrect. Specifically this fixes the situation when booting a relocatable kernel and the memory is reported as an offset and size in the device tree, and the size needs to be adjusted accordingly. Signed-off-by: Matthew McClintock <msm@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org>
| * Replace CHANGELOG files by auto-generated "snapshot.commit"Wolfgang Denk2010-08-07-94577/+1
| | | | | | | | | | | | Idea and implementation courtesy of Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
generated by cgit v1.1 at 2024-12-19 10:30:59 +0000