summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* mmc: SEND_OP_COND considers card capabilities (voltage)Raffaele Recalcati2011-04-13-3/+20
| | | | | | | | | | | The first SEND_OP_COND (CMD1) command added is used to ask card capabilities. After it an AND operation is done between card capabilities and host capabilities (at the moment only for the voltage field). Finally the correct value is sent to the MMC, waiting that the card exits from busy state. Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: checking status after commands with R1b responseRaffaele Recalcati2011-04-13-3/+63
| | | | | | | | | | It is recommended to check card status after these kind of commands. This is done using CMD13 (SEND_STATUS) JEDEC command until the card is ready. In case of error the card status field is displayed. Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: remove duplicated header fileMinkyu Kang2011-04-13-1/+0
| | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: show mmc capacity using print_sizeMinkyu Kang2011-04-13-1/+2
| | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: add generic mmc spi driverThomas Chou2011-04-13-20/+448
| | | | | | | | | | | | | This patch supports mmc/sd card with spi interface. It is based on the generic mmc framework. It works with SDHC and supports multi blocks read/write. The crc checksum on data packet is enabled with the def, There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: constify & localize dataMike Frysinger2011-04-13-2/+2
| | | | | | | These local vars need not be writable nor exported. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* drivers/mmc/fsl_esdhc.c: reordered testsFrans Meulenbroeks2011-04-13-3/+3
| | | | | | | | | | | | As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error would yield the first error return instead of TIMEOUT. By swapping the test TIMEOUTs are reported as such An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define but as that one might be less desired I've opted for the simplest solution Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* add CONFIG_SPI_IDLE_VAL for cf_spi.c to allow use of spi_mmcWolfgang Wegner2011-04-13-3/+11
| | | | | | | | | | This patch adds CONFIG_SPI_IDLE_VAL to cf_spi.c The default setting is 0x0 to behave same as current version, in case CONFIG_SPI_MMC is set, the value is set to 0xFFFF (all ones). In either case, the value can be overwritten by board configuration. Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Andy Fleming <afleming@freescale.com>
* MMC: Max blocks value adjustableMatt Waddel2011-04-13-10/+9
| | | | | | | | | | The maximum blocks value was hardcoded to 65535 due to a 16 bit register length. The value can change for different platforms. This patch makes the default the current value of 65535, but it is configurable for other platforms. Signed-off-by: Matt Waddel <matt.waddel@linaro.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* SD1.00 wide-bus fixAlagu Sankar2011-04-13-3/+3
| | | | | | Fixed a bug wherein SD version 1.0 cards were not configured for 4-bit mode Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
* disk/part.c: fix potential stack overflow bugLei Wen2011-04-12-1/+1
| | | | | | | | If the param pass to get_dev is not the one defined in the block_drvr, it could make uboot becomes unstable, for it would continue run after search complete the block_drvr table. Signed-off-by: Lei Wen <leiwen@marvell.com>
* Add support for dataflash to U-boot environment settings tool.Remy Bohmer2011-04-12-28/+56
| | | | | | | | | | * The sector size for SPI-dataflash (like AT45 flashes) are not always a power-of-2. So, the sector calculations are rewritten such that it works for either power-of-2 as any size sectors. * Make the flash sector size optional in case it is the same value as the environment size. Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mkimage: add "-V" option to print version informationWolfgang Denk2011-04-12-2/+12
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ftwdt010_wdt: move header to include/faraday and enhanceMacpaul Lin2011-04-12-5/+10
| | | | | | | | | | | | | 1. Move header to include/faraday 2. Fix include path in ftwdt010_wdt.c 3. Fix function prototype and declaration to - ftwdt010_wdt_settimeout - ftwdt010_wdt_reset - ftwdt010_wdt_disable 4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty to choose which better to his product. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* common/cmd_bdinfo.c: fix do_bdinfo() for AVR32Andreas Bießmann2011-04-12-1/+1
| | | | | | | | | | | | | | This patch fixes following warning message: ---8<--- cmd_bdinfo.c:458: warning: initialization from incompatible pointer type --->8--- There was a prototype change in 54841ab50c20d6fa6c9cc3eb826989da3a22d934 for argv[] pointer type to const. This change was not made for AVR32 cause this code came in later by a merge. Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* cmd_nvedit: use explicit typecast for printfAndreas Bießmann2011-04-12-2/+2
| | | | | | | | | | | This patch fixes warnings in MAKEALL for avr32: ---8<--- cmd_nvedit.c: In function 'do_env_export': cmd_nvedit.c:663: warning: format '%zX' expects type 'size_t', but argument 3 has type 'ssize_t' --->8--- Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* Make STANDALONE_LOAD_ADDR configurable per boardWolfgang Denk2011-04-12-16/+24
| | | | | | | | | | | | | Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR and allow that the architecture-specific default value gets overwritten by defining the value in the board header file. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* Drop config.h include in tools/imximage.hLoïc Minier2011-04-12-2/+0
| | | | | | | | | | | | "make tools-all" should allow building tools such as mkimage and the new imximage without any config, but imximage.c currently fails to build with: imximage.h:27:20: error: config.h: No such file or directory config.h is not needed in imximage.h nor in imximage.c, and imximage.h is only included from imximage.c, so drop this include to fix the build. Signed-off-by: Loïc Minier <loic.minier@linaro.org>
* Fix misc spelling errors found by lintianLoïc Minier2011-04-12-10/+10
| | | | Signed-off-by: Loïc Minier <loic.minier@linaro.org>
* Fix gunzip to work for any gziped uImage sizeCatalin Radu2011-04-12-6/+10
| | | | Signed-off-by: Catalin Radu <Catalin@VirtualMetrix.com>
* Fix min/max macros in include/common.hAaron Williams2011-04-12-2/+4
| | | | | | | | | | There is a bug in the min and max macros in common.h which occurs if Y is a larger type than X. For example, if Y is a 64-bit value and X is a 32-bit value then Y will be truncated to 32-bits. This fix matches what is done in the Linux kernel but without the additional type checking present in the kernel version. Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
* ftwdt010_wdt: support faraday ftwdt010 watchdogMacpaul Lin2011-04-11-0/+206
| | | | | | | | Faraday ftwdt010 watchdog is an architecture independant watchdog. It is usually used in SoC chip design. Signed-off-by: Macpaul Lin <macpaul@andestech.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* mp2usb: remove board supportEric Bénard2011-04-11-945/+0
| | | | | | | this board was cancelled long time ago so remove it as it won't be maintained anymore Signed-off-by: Eric Bénard <eric@eukrea.com>
* ppc, mgcoge: add DIP switch detectionAndreas Huber2011-04-11-0/+23
| | | | | | | | | This reads the DIP switch on mgcoge. The DIP switch is connected to the BFTICU (0x40000089) FPGA. If the DIP switch is set the environment variable 'actual_bank' is set to 0 and starts the SW in bank0. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* arm, keymile: remove unneeded codeHolger Brunck2011-04-11-7/+0
| | | | | | | | On first HW versions the BOCO FPGA was behind a MUX device. These HW versions are not supported anymore. And therefore this code can be removed, it is already unused. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* Net: Add Intel E1000 82574L PCIe card supportRoy Zang2011-04-11-8/+32
| | | | | | | | | Add Intel E1000 82574L PCIe card support. Test on MPC8544DS and MPC8572 board. Add the missing contact information for future support. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org>
* PowerPC: Add support for -msingle-pic-baseJoakim Tjernlund2011-04-11-12/+127
| | | | | | | | | | | | | -msingle-pic-base is a new gcc option for ppc and it reduces the size of my u-boot with 6-8 KB. While at it, add -fno-jump-tables too to save a few more bytes. -msingle-pic-base will be in gcc 4.6, however backported patches are available at http://bugs.gentoo.org/show_bug.cgi?id=347281 Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* PowerPC: Move -fPIC flag to common placeJoakim Tjernlund2011-04-11-13/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | The -fPIC flag belongs with -mrelocatable, move it there. Also change -fPIC to -fpic as this produces smaller binaries. However, currently -mrelocatable promotes -fpic to -fPIC, a fix for this is in upcoming gcc 4.6 or you can apply this small patch to gcc: diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h index 8da8410..e4b8280 100644 --- a/gcc/config/rs6000/sysv4.h +++ b/gcc/config/rs6000/sysv4.h @@ -227,7 +227,8 @@ do { \ } \ \ else if (TARGET_RELOCATABLE) \ - flag_pic = 2; \ + if (!flag_pic) \ + flag_pic = 2; \ } while (0) #ifndef RS6000_BI_ARCH -- Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* ea20: fix undefined PHY_* errorsBen Gardiner2011-04-11-3/+3
| | | | | | | | | | | This patch fixes ea20 after 8ef583a0351590a91394499eb5ca2ab8a703d959 where the u-boot custom PHY_ macros were replaced with those of linux/mii.h MII_ definitions except in the RMII support for davinci_emac. Probably also due to the merge path of changes in 2010.12. Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca> CC: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
* ea20: fix libea20.o not foundBen Gardiner2011-04-11-1/+1
| | | | | | | | | | This patch fixes ea20 after commit 6d8962e814c15807dd6ac5757904be2a02d187b8 where $(obj)lib$(BOARD).a was changed to $(obj)lib$(BOARD).o in almost all the Makefiles except ea20, probably due to merge path of the changes in 2010.12. Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca> CC: Sebastien Carlier <sebastien.carlier@gmail.com> Acked-by : Stefano Babic <sbabic@denx.de>
* bootm: replace blob_start with image_startLei Wen2011-04-11-1/+1
| | | | | | | | | | | For uImage always has a 64 bytes header, we couldn't expect to do the xip from the header but should xip from the image start. The latter logic in that section is also move the image from image_start to the load address, so sync this logic to the xip operation. Signed-off-by: Lei Wen <leiwen@marvell.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
* sf: unify read functionsMike Frysinger2011-04-11-157/+22
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* sf: unify erase functionsMike Frysinger2011-04-11-335/+83
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* sf: unify status polling for ready bitMike Frysinger2011-04-11-283/+81
| | | | | | | | All of the spi flash drivers implement the status register polling for detecting the device ready state, so unify them all in a new helper function -- spi_flash_wait_ready. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* sf: unify read/write helpersMike Frysinger2011-04-11-48/+19
| | | | | | | These functions largely do the same exact thing, so unify them all into one basic function. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2011-04-10-159/+394
|\
| * powerpc/85xx: Removed clearing of L2-as-SRAMFabian Cenedese2011-04-10-7/+0
| | | | | | | | | | | | | | | | Removed clearing of L2 cache as SRAM as it is not necessary without ECC. This also speeds up the booting process. Signed-off-by: Fabian Cenedese <cenedese@indel.ch> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * fsl_esdhc: Deal with watermark level register related changesPriyanka Jain2011-04-10-5/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark level register description has been changed: 9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00 25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00 Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add PBL boot from SPI flash support on P4080DSShaohui Xie2011-04-10-2/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as 1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from CPC after PBL completes RCW and PBI phases. Signed-off-by: Chunhe Lan <b25806@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Update default hwconfig on P1022DSJiang Yutang2011-04-10-0/+1
| | | | | | | | | | | | | | | | Set default configuration to have SDHC controller enabled, AUDIO enabled(codec clock sources is 12MHz) and disable TDM. Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add support usb2/etsec and tdm/audio pin multiplex on P1022DSJiang Yutang2011-04-10-11/+79
| | | | | | | | | | | | | | | | | | | | | | For soc which have pin multiplex relation, some of them can't enable simultaneously. This patch add environment var 'hwconfig' content defination for them. you can enable some one function by setting environment var 'hwconfig' content and reset board. Detail setting please refer doc/README.p1022ds Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Enable support for ATI graphics cards on P1022DSJiang Yutang2011-04-10-0/+16
| | | | | | | | | | | | | | Make the support for ATI graphics cards mutually exclusive with DIU. Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * p4080ds: remove rev1-specific code for the SERDES8 erratumTimur Tabi2011-04-10-59/+47
| | | | | | | | | | | | | | | | Remove the SERDES8 erratum work-around code that only applied to P4080 rev1, which is not supported by this version of U-Boot. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * p4080ds: add README.p4080ds which documents the "serdes" hwconfig optionTimur Tabi2011-04-10-0/+32
| | | | | | | | | | | | | | | | | | Add documentation for the "serdes" hwconfig option, which is used to specify the status of SerDes banks two and three for the SERDES8 erratum work-around. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Drop CONFIG_VIDEO support on corenet_ds boardsKumar Gala2011-04-09-23/+0
| | | | | | | | | | | | | | | | We don't really ever use Video cards on corenet_ds style boards and its bloating our image which is close the its max size. Drop support and also kill some defines for non-PNP PCI which we never use. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: rename NAND prefixes to CONFIG_SYSMatthew McClintock2011-04-08-41/+41
| | | | | | | | | | | | | | | | | | | | renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more appropriate CONFIG_SYS prefix as well as be consistent with 83xx. Signed-off-by: Matthew McClintock <msm@freescale.com> cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add some defines & registers in immap_85xx.hZhao Chenhui2011-04-05-1/+6
| | | | | | | | | | | | | | | | | | * Added SDHCDCR register to GUR struct * Added SDHCDCR_CD_INV define related to SDHCDCR * Added Pin Muxing define related to TDM on P102x Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add P1021 specific QE and UEC supportHaiying Wang2011-04-05-11/+84
| | | | | | | | | | | | | | | | | | | | | | | | | | | | P1021 has some QE pins which need to be set in pmuxcr register before using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to be released after MII access because QE12 pin is muxed with LBCTL signal. Also added relevant QE support defines unique to P1021. The P1021 QE is shared on P1012, P1016, and P1025. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: don't init SDRAM when CONFIG_SYS_RAMBOOTZhao Chenhui2011-04-05-0/+12
| | | | | | | | | | | | Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'next' of git://git.denx.de/u-boot-niosWolfgang Denk2011-04-10-0/+16
|\ \
generated by cgit v1.1 at 2024-12-16 01:34:38 +0000