summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* Add initial support for Freescale mx51evk boardStefano Babic2010-03-07-0/+830
| | | | | | | | The patch adds initial support for the Freescale mx51evk board. Network (FEC) and SD controller (fsl_esdhc) are supported. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* fsl_esdhc: add support for mx51 processorStefano Babic2010-03-07-49/+173
| | | | | | | | | The esdhc controller in the mx51 processor is quite the same as the one in some powerpc processors (MPC83xx, MPC85xx). This patches adapts the driver to support the arm mx51. Signed-off-by: Stefano Babic <sbabic@denx.de>
* ARM: add accessors functionsStefano Babic2010-03-07-0/+55
| | | | | | | | | | Some Freescale's processors of different architecture have the same peripheral (eSDHC controller in PowerPC and i.MX51). This patch adds accessors for the internal registers of the SOCs, as already implemented in the PowerPC architecture. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MMC: add weak function to detect MMC/SD cardStefano Babic2010-03-07-0/+8
| | | | | | | | | | | Most controllers can check if there is a card in the slot. However, they require pins that could be not available because required by other functions and the detection of a card must be performed in another way. This patch adds a weak function that a board can implement to add its internal custom way to check the presence of a MMC/SD card. Signed-off-by: Stefano Babic <sbabic@denx.de>
* mmc: check correctness of the voltage mask in ocrStefano Babic2010-03-07-1/+9
| | | | | | | | | | Most cards do not answer if some reserved bits in the ocr are set. However, some controllers can set bit 7 (reserved for low voltages), but how to manage low voltages SD card is not yet specified. Signed-off-by: Stefano Babic <sbabic@denx.de>
* serial_mxc: add support for MX51 processorStefano Babic2010-03-07-6/+12
| | | | | | | The patch adds support for the Freescale mx51 processor. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* MX51: Add pin and multiplexer definitions.Stefano Babic2010-03-07-0/+567
| | | | | | | | The patch add header files to support the pin multiplexer of the the Freescale i.MX51 processor. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* MX51: Add register definitionsStefano Babic2010-03-07-0/+524
| | | | | | | | The patch add header files to support the Freescale i.MX51 processor, setting definitions for internal registers. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* MX51: Add initial support for the Freescale MX51Stefano Babic2010-03-07-0/+1115
| | | | | | | | The patch add initial support for the Freescale i.MX51 processor (family arm cortex_a8). Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* edb93xx: Fix SDRAM initializationMatthias Kaehlcke2010-03-07-8/+31
| | | | | | | | | edb93xx: Fix SDRAM initialization by issuing a precharge all command before forcing the precharge and select mode register update mode before programming the mode registers. Write to the SDRAM banks in order to force a precharge, reading causes the edb93xx boards to hang Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
* Add bootcount to AT91Anders Darander2010-03-07-0/+34
| | | | | | | Use AT91_GPBR 3 as a bootcount register. The bootmagic and the bootcount shares AT91_GPBR 3. Signed-off-by: Anders Darander <ad@datarespons.se>
* ARM Update mach-typesTom Rix2010-03-07-7/+1021
| | | | | | | | | | Fetched from http://www.arm.linux.org.uk/developer/machines/download.php And built with repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm commit aea187c46f7d03ce985e55eb1398d0776a15b928 Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* ep93xx: Refactoring of timer codeMatthias Kaehlcke2010-03-07-44/+26
| | | | | | | | | | | | | ep93xx: Refactoring of the timer code, including the following changes * use a free running timer instead of a periodical one * use unsigned long long for total number of ticks * hold the timer state in a structure instead of separate variables * increment the timer counter instead of decrementing it * remove unused function udelay_masked() * remove unused function set_timer() Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
* ep93xx: Fix calculation of sys ticks in clk_to_systicks()Matthias Kaehlcke2010-03-07-2/+4
| | | | | | | ep93xx: Use unsigned long long for calculation of sys ticks in clk_to_systicks() for proper handling of large intermediate values Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
* OMAP3: workaround for ARM Cortex-A8 erratum 725233Siarhei Siamashka2010-03-07-0/+6
| | | | | | | | | | | | | | | | | | | | | | 725233: PLD instructions executed with PLD data forwarding enabled can result in a processor deadlock This deadlock can happen when NEON load instructions are used together with cache preload instructions (PLD). The problematic conditions can be triggered in-the-wild by NEON optimized functions from pixman library (http://cgit.freedesktop.org/pixman), which perform dynamic adjustment of prefetch distance. The workaround disables PLD data forwarding by setting PLD_FWD bit in L2 Cache Auxiliary Control Register as recommended in ARM Cortex-A8 errata list. The deadlock can only happen on r1pX revisions of Cortex-A8 (used in OMAP34xx/OMAP35xx). Performance impact of the workaround is practically non-existant. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARM change name of defines for AT91 arm926ejsAchim Ehrlich2010-03-07-34/+34
| | | | | | | | | | Configuration defines should be preceeded with CONFIG_SYS_. Renamed some at91 specific defines to conform to this naming convention: AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
* VoiceBlue: fix linker errorsLadislav Michl2010-03-07-127/+65
| | | | | | | | | | | | | | | | | | linking eeprom with libgeneric.a is not really needed and causes following error: ../../lib_generic/libgeneric.a(string.o): In function `strcmp': /home/ladis/src/u-boot-ti/lib_generic/string.c:152: multiple definition of `strcmp' ../../examples/standalone/libstubs.a(stubs.o):include/_exports.h:24: first defined here make[1]: *** [eeprom.srec] Error 1 Fix undefined reference to memset generated by some versions of gcc to zero out initialized structure on the stack: eeprom.o: In function `eeprom': board/voiceblue/eeprom.c:152: undefined reference to `memset' make[1]: *** [eeprom] Error 1 Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* VoiceBlue: limit line lenght to 80 charactersLadislav Michl2010-03-07-86/+82
| | | | | | | | Reindent configuration header to limit line lenght to 80 characters by removing obvious and sometimes misleading comments. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* netstar.h: do not exceed 80 columnsLadislav Michl2010-03-07-34/+31
| | | | | | | | Limit line length to 80 characters mostly by removing obvious and sometimes misleading comments. Fix indentation, too. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* DaVinci: Adding entry to MAKEALL for DM365 EVMSandeep Paulraj2010-03-07-0/+1
| | | | | | The patch adds an entry for the DM365 EVM to MAKEALL Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da830evm: Add support for TI EMACNick Thompson2010-03-07-2/+65
| | | | | | | | | | | Adds support for ethernet networking on the da830evm platform. This platform uses an SoC EMAC interface and a 3 port ethernet switch as a PHY with an RMII interface. The PHY also has a i2c interface for configuring the switch functions. Signed-off-by: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* NetStar: make mtdparts default ready for recent kernelsLadislav Michl2010-03-07-4/+3
| | | | | | | | Recent kernels are using generic NAND and NOR drivers. Change default mtdparts to reflect it. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* NetStar: fix default environmentLadislav Michl2010-03-07-21/+21
| | | | | | | Correct switching partitions after upgrade and make it more readable. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* NetStar: eeprom - fix linker errorLadislav Michl2010-03-07-93/+25
| | | | | | | | | | | | | | linking eeprom with libgeneric.a is not really needed and causes following error: ../../lib_generic/libgeneric.a(string.o): In function `strcmp': lib_generic/string.c:152: multiple definition of `strcmp' ../../examples/standalone/libstubs.a(stubs.o):include/_exports.h:24: first defined here Remove eeprom linker script as well and generate entry point object (to start application by jumping on its beginning) on the fly. Out-of-tree build tested as well. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* NetStar: eeprom - be less verboseLadislav Michl2010-03-07-14/+13
| | | | | | | | Use shorter yet descriptive messages, replace printf() with puts() where appropriate. This saves few bytes. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* NetStar: eeprom - undefined reference to `memset'Ladislav Michl2010-03-07-31/+37
| | | | | | | | | | | Defining partially initialized struct eth_device on stack means gcc has to zero out it, and some gcc versions optimize this with an implicit call to memset. Move definition to data section to avoid that (it has also nice side effect that we need not to pass it to helper functions anymore) Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk2010-03-04-1/+2
|\
| * ] fix monitor protection for CONFIG_MONITOR_IS_IN_RAMWolfgang Wegner2010-03-04-1/+2
| | | | | | | | | | | | | | | | | | | | For platforms with flash below ram addresses, the current check to activate monitor protection is wrong/insufficient. This patch fixes CONFIG_MONITOR_IS_IN_RAM for these systems by adding a check for this configuration. Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2010-03-04-6/+18
|\ \
| * | ppc4xx: Corrected EBC register bit definitionsEugene O'Brien2010-03-02-6/+18
| |/ | | | | | | | | | | | | | | | | | | Corrected the bit field positions of the external master priority low and the external master priority high values in the EBC configuration register. These bit field positions differ between PPC405 and PPC440 processors Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'next' of git://git.denx.de/u-boot-coldfireWolfgang Denk2010-03-04-1/+62
|\ \
| * | allow MCF532x to use CONFIG_MONITOR_IS_IN_RAMWolfgang Wegner2010-03-04-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_MONITOR_IS_IN_RAM is broken for MCF532x. This patch fixes this by conditionally - removing the vector table at the beginning of code - not overwriting the vector base register - removing the code to re-set the PLL, which effectively disables SDRAM access Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
| * | MCF5271-only: Added a weak board_reset function to allow custom resetRichard Retanubun2010-03-04-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a board_reset function to allow boards to specify their own custom reset sequence (e.g. resetting by timing out watchdog). Tested only on MCF5271, can be expanded if needed. Based on Mike Frysinger's suggestion on: http://article.gmane.org/gmane.comp.boot-loaders.u-boot/70304 Signed-off-by: Richard Retanubun <RichardRetanubun at RuggedCom.com>
| * | MCF532x: make icache_enable use CONFIG_SYS_SDRAM_SIZEWolfgang Wegner2010-03-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | in cpu/mcf532x/start.S, the function icache_enable enables the cache for a fixed 32MB region starting at the SDRAM start address; this patch changes the function to cover the region defined by CONFIG_SYS_SDRAM_SIZE Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
| * | add include/asm-m68k/unaligned.hWolfgang Wegner2010-03-04-0/+15
| |/ | | | | | | | | | | | | | | | | lib_generic/zlib.c needs include/asm/unaligned.h since commit cd514aeb996e2f7aefbe1f78481965d9d074aed4, which broke compilation for Coldfire/M68K. This patch adds the missing header for these architectures. Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk2010-03-04-0/+283
|\ \
| * | sh: Add asm/unaligned.h and asm/unaligned-sh4a.h from Linux kernelNobuhiro Iwamatsu2010-03-03-0/+283
| |/ | | | | | | | | | | | | | | zlib.c demands asm/unaligned.h. But, SH does not have these. This commit add asm/unaligned.h and asm/unaligned-sh4a.h from Linux kernel and modifyf for u-boot. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2010-03-04-79/+165
|\ \ | |/ |/|
| * mpc83xx: fix out-of-tree mpc8315 nand buildKim Phillips2010-03-02-3/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 2e95004deb6e33e33bf1b8a92a38cd2115bac4c2 "mpc83xx: Add NAND boot support for MPC8315E-RDB boards" symlinked nand_spl/board/freescale/mpc8315erdb to mpc8313erdb in order to not duplicate code. Since the main makefile builds nand_spl/board/$(BOARDDIR) (which makes sense), and the board Makefile and linker script are the only two necessary files to enable out-of-tree building, and other boards have duplicated nand makefiles (e.g. 8536ds & 8569mds), it only seems prudent to copy these two files in the name of the 8315 too. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Wolfgang Denk <wd@denx.de>
| * mpc83xx: vme8349: fix incorrect BR0_PRELIM port size commentKim Phillips2010-03-02-2/+2
| | | | | | | | | | | | | | commit 98d92d8c9f4021629a45261ad5ec3f3595f3a27a "sbc8349: fix incorrect comment" missed this one. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * mpc83xx: remove hardcoded network addresses from config filesKim Phillips2010-02-22-69/+0
| | | | | | | | | | | | | | and avoid e.g., two identical boards from causing random networking conflicts when hooked up to the same network. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * Bug: do_reset issued via netconsole does not reset mpc83xx cpu.Michael Zaidman2010-02-18-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | The do_reset routine in the cpu/mpc83xx/cpu.c file does not reset the mpc83xx cpu when issued via netconsole. Moving the console output "resetting the board." to the beginning of the routine before disabling interrupts solved the problem. Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | cmd_itest.c: fix pointer dereferencingFrans Meulenbroeks2010-02-24-2/+7
| | | | | | | | | | | | | | | | fix pointer dereferencing if the size is .b and .w an 8 or 16 bit access is done. Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de>
* | tools: fix imximage warningKim Phillips2010-02-24-1/+1
| | | | | | | | | | | | | | | | | | | | | | Fix build warning: Configuring for MPC837XEMDS board... imximage.c: In function `imximage_parse_cfg_file': imximage.c:146: warning: passing argument 2 of `getline' from incompatible pointer type /usr/include/bits/stdio.h:116: note: expected `size_t *' but argument is of type `uint32_t *' Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | mkimage: SEGFAULT with imximage on 64 bit systemsStefano Babic2010-02-24-17/+15
|/ | | | | | | | Running mkimage to generate an imximage produces a SEGFAULT on 64 bit machines due to pointer arithmetic limited to 32 bit. Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* new board (eb_cpux9k2)Jens Scharsig2010-02-12-0/+861
| | | | | | | | | | * new board (eb_cpux9k2) * support for EB+CPUx9K2 board by BuS Elektronik GmbH & Co. KG * select via make eb_cpux9k2_config * this also demonstrates, how to use boards with AT91RM9200 cpu in at91 arch tree Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* new at91_emac network driver (NET_MULTI api)Jens Scharsig2010-02-12-3/+1
| | | | | | | | | | | * add's at91_emac (AT91RM9200) network driver (NET_MULTI api) * enable driver with CONFIG_DRIVER_AT91EMAC * generic PHY initialization * modify AT91RM9200 boards to use NET_MULTI driver * the drivers has been tested with LXT971 Phy and DM9161 Phy at MII and RMII interface Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* prepare joining at91rm9200 into at91Jens Scharsig2010-02-12-6/+825
| | | | | | | | | | | | * prepare joining at91 and at91rm9200 * add modified copy of soc files to cpu/arm920t/at91 to make possible to compile at91rm9200 boards in at91 tree instead of at91rm9200 * add header files with c structure defs for AT91 MC, ST and TC * the new cpu files are using at91 c structure soc access * please read README.soc-at91 for details Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* update at91sam9263ek board to new SoC accessJens Scharsig2010-02-12-128/+132
| | | | | | | * convert at91sam9263ek board to use c stucture SoC access * change gpio access to at91_gpio syntax Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* convert common files to new SoC accessJens Scharsig2010-02-12-127/+261
| | | | | | | | * add's a warning to all files, which need update to new SoC access * convert common files in cpu/../at91 and a lot of drivers to use c stucture SoC access Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
generated by cgit v1.1 at 2024-12-30 18:50:55 +0000