summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* Add SPI support to mx51evk boardStefano Babic2010-05-05-0/+154
| | | | | | | The patch adds SPI devices to the mx51evk board. The MC13892 chip (PMIC) is supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX: Added definition file for MC13892Stefano Babic2010-05-05-0/+160
| | | | | | | | The MC13892 is a Power Controller used with processors of the family MX.51. The file adds definitions to be used to setup the internal registers via SPI. Signed-off-by: Stefano Babic <sbabic@denx.de>
* SPI: added support for MX51 to mxc_spiStefano Babic2010-05-05-20/+211
| | | | | | This patch add SPI support for the MX51 processor. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX31: Add support for PMIC to the QONG moduleStefano Babic2010-05-05-0/+34
| | | | | | | Add support for the PMIC (MC13783) controller and enables charging of the RTC battery. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX: RTC13783 uses general function to access PMICStefano Babic2010-05-05-67/+31
| | | | | | | | The RTC is part of the Freescale's PMIC controller. Use general function to access to PMIC internal registers. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
* MX: Added Freescale Power Management DriverStefano Babic2010-05-05-0/+329
| | | | | | | | | The patch add supports for the Freescale's Power Management Controller (known as Atlas) used together with i.MX31/51 processors. It was tested with a MC13783 (MX31) and MC13892 (MX51). Signed-off-by: Stefano Babic <sbabic@denx.de>
* i.MX31: Activate NAND support for i.MX31 Litekit board.Magnus Lilja2010-05-05-0/+10
| | | | Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
* MX51: Fix MX51 CPU detect messageFabio Estevam2010-05-05-1/+1
| | | | | | | | | | | | | | Fix MX51 CPU detect message. Original string was: CPU: Freescale i.MX51 family 3.0V at 800 MHz which can be misinterpreted as 3.0 Volts instead of the silicon revision. ,change it to: CPU: Freescale i.MX51 family rev3.0 at 800 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX51evk: Removed warningsStefano Babic2010-05-05-2/+2
| | | | | | | Changes reflect modifications in the fsl_esdhc driver (the clk_enable field war removed in the configuration structure). Signed-off-by: Stefano Babic <sbabic@denx.de>
* tx25: fix crash while booting LinuxAnatolij Gustschin2010-05-05-0/+3
| | | | | | | | | | Currently booting Linux on TX25 board doesn't work since there is no correct mach-id and boot parameters setup for tx25 board. Fix it now. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* configs: remove unused CONFIG_COMMAND_HISTORYKim Phillips2010-05-04-3/+0
| | | | | | | | | | | | $ git grep CONFIG_COMMAND_HISTORY CHANGELOG: CONFIG_COMMAND_HISTORY include/configs/AP1000.h:#define CONFIG_COMMAND_HISTORY 1 include/configs/keymile-common.h:#define CONFIG_COMMAND_HISTORY 1 include/configs/manroland/common.h:#define CONFIG_COMMAND_HISTORY 1 $ Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
* mvsmr: fix link errorAnatolij Gustschin2010-05-04-5/+5
| | | | | | | | | | | MVSMR board support doesn't link since recent rework of U-Boot directory structure. Fix it now. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Fixed merge conflict Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk2010-05-04-211/+2120
|\
| * Blackfin: bfin_mac: hook up new write_hwaddr functionMike Frysinger2010-05-03-15/+16
| | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: ethoc: add write_hwaddr supportThomas Chou2010-05-03-3/+3
| | | | | | | | | | Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: altera_tse: add write_hwaddr supportThomas Chou2010-05-03-28/+35
| | | | | | | | | | Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: fec_mxc: add write_hwaddr supportHeiko Schocher2010-05-03-1/+1
| | | | | | | | | | | | | | tested on the magnesium board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net:kirkwood_egiga.c: MAC addresses programming using write_hwaddrPrafulla Wadaskar2010-05-03-0/+11
| | | | | | | | | | | | | | | | | | Added a new function kwgbe_write_hwaddr for programming egiga controller's hardware address. This function will be called for each egiga port being used Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * Program net device MAC addresses after initializingBen Warren2010-05-03-5/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a new function to the eth_device struct for programming a network controller's hardware address. After all network devices have been initialized and the proper MAC address for each has been determined, make a device driver call to program the address into the device. Only device instances with valid unicast addresses will be programmed. Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de> Tested-by: Prafulla Wadaskar <prafulla@marvell.com> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Thomas Chou <thomas@wytron.com.tw>
| * net: add altera triple speeds ethernet mac driverThomas Chou2010-05-03-0/+1432
| | | | | | | | | | | | | | | | This driver supports the Altera triple speeds 10/100/1000 ethernet mac. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: add opencore 10/100 ethernet mac driverThomas Chou2010-05-03-0/+513
| | | | | | | | | | | | | | | | This patch ports the opencore 10/100 ethernet mac driver ethoc.c from linux kernel to u-boot. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * smc911x driver frame alignment patchValentin Yakovenkov2010-05-03-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SMSC911x chips have alignment function to allow frame payload data (which comes after 14-bytes ethernet header) to be aligned at some boundary when reading it from fifo (usually - 4 bytes boundary). This is done by inserting fake zeros bytes BEFORE actual frame data when reading from SMSC's fifo. This function controlled by RX_CFG register. There are bits that represents amount of fake bytes to be inserted. Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long, so we need to add 2 fake bytes to get payload data aligned at 4-bytes boundary. Linux driver does this by adding IP_ALIGNMENT constant (defined at skb.h) when calculating fifo data length. All network subsystem of Linux uses this constant too when calculating different offsets. But u-boot does not use any packet data alignment, so we don't need to add anything when calculating fifo data length. Moreover, driver zeros the RX_CFG register just one line up, so chip does not insert any fake data at the beginig. So calculated data length is always bigger by 1 word. It seems that at almost every packet read we get an underflow condition at fifo and possible corruption of data. Especially at continuous transfers, such as tftp. Just after removing this magic addition, I've got tftp transfer speed as it aught to be at 100Mbps. It was really slow before. It seems that fifo underflow occurs only when using byte packing on 32-bit blackfin bus (may be because of very small delay between reads). Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: Kirkwood_egiga.c bugfixes for rx pathPrafulla Wadaskar2010-05-03-4/+5
| | | | | | | | | | | | | | | | | | Cosmetic changes: Few comments updated Functionality: Rx packet frame size is programming should be done when port is in disabled state. this is corrected Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * fec_mxc.c: Fix MX27 FEC MAC validity checkEric Jarrige2010-05-03-1/+1
| | | | | | | | | | | | | | | | Fix MX27 FEC logic to check validity of the MAC address in fuse. Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change. Signed-off-by: Eric Jarrige <jorasse@armadeus.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * tsec: Wait for both RX and TX to stopAndy Fleming2010-05-03-1/+2
| | | | | | | | | | | | | | | | | | When gracefully stopping the controller, the driver was continuing if *either* RX or TX had stopped. We need to wait for both, or the controller could get into an invalid state. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: dm9000x: use standard I/O accessorsMike Frysinger2010-05-03-6/+6
| | | | | | | | | | | | | | | | | | | | The current dm9000x driver accesses its memory mapped registers directly instead of using the standard I/O accessors. This can cause problems on Blackfin systems as the accesses can get out of order. So convert the direct volatile dereferences to use the normal in/out macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * mpc512x_fec: Move PHY initialization from probe into init routine.Detlev Zundel2010-05-03-22/+7
| | | | | | | | | | | | | | This saves the autonegotation delay when not using ethernet in U-Boot Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * fec_mxc don't use internal eeprom on MX25John Rigby2010-05-03-2/+2
| | | | | | | | | | | | | | Avoid using the internal eeprom on MX25 like MX51 already does. Signed-off-by: John Rigby <jcrigby@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * fix lockup in mcfmii/mii_discover_phy() in case communication failsWolfgang Wegner2010-05-03-22/+23
| | | | | | | | | | Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * 83xx: UEC: Added support for bitBang MII driver access to PHYsRichard Retanubun2010-05-03-4/+49
| | | | | | | | | | | | | | | | | | | | | | This patch enabled support for having PHYs on bitBang MII and uec MII operating at the same time. Modeled after the MPC8360ADS implementation. Added the ability to specify which ethernet interfaces have bitbang SMI on the board header file. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * ./net/net.c - make Microsoft dns servers happy with random_port() numbersRobin Getz2010-05-03-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | For some reason, (which I can't find any documentation on), if U-Boot gives a port number higher than 17500 to a Microsoft DNS server, the server will reply to port 17500, and U-Boot will ignore things (since that isn't the port it asked the DNS server to reply to). This fixes that by ensuring the random port number is less than 17500. Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * Remove unused "local_crc32" function.Detlev Zundel2010-05-03-120/+3
| | | | | | | | | | | | | | For code archeologists, this is a nice example of copy and paste history. Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: Trivial coding style issue with empty for statementDetlev Zundel2010-05-03-2/+3
| | | | | | | | | | Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: Kirkwood_egiga.c: fixed build warningsPrafulla Wadaskar2010-05-03-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | This patch fixes following build warnings for kirkwood_egiga.c kirkwood_egiga.c: In function "kwgbe_init": kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules kirkwood_egiga.c: In function "kwgbe_recv": kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-05-04-738/+2817
|\ \ | |/ |/|
| * pm9263 converted to at91 soc accessAsen Dimov2010-04-30-145/+152
| | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * at91: define matrix registers bit fieldsAsen Dimov2010-04-30-0/+138
| | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * MX31: Removed erroneous board name from QONGStefano Babic2010-04-30-1/+1
| | | | | | | | | | | | | | QONG is a module that can be installed on several boards, not only on the QONG-EVB manufactured by Dave srl. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: Add UBI support to QONG moduleStefano Babic2010-04-30-4/+9
| | | | | | | | | | | | The UBI/UBIFS support is added to the QONG module. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: Support 128MB RAM on QONG moduleStefano Babic2010-04-30-33/+103
| | | | | | | | | | | | | | | | | | The QONG module can be downsized and delivered with 128MB instead of 256MB. The patch adds run time support for the two different memory configurations. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: Add support for NAND to QONG boardStefano Babic2010-04-30-23/+101
| | | | | | | | | | | | | | | | The NAND device is connected to the FPGA of the QONG board and not to the NFC controller. For this reason, the FPGA must be set and initialized before accessing to the NAND itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: add pin definitions for NAND controllerStefano Babic2010-04-30-0/+9
| | | | | | | | | | | | | | Add pin definitions ralted to the NAND controller to be used to set up the pin multiplexer. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX31: add accessor function to get a gpioStefano Babic2010-04-30-0/+20
| | | | | | | | | | | | The patch adds an accessor function to get the value of a gpio. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * mx51evk: correct list of possible BOOT_FROM valuesStefano Babic2010-04-30-1/+1
| | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
| * mkimage: correct spelling error in imximageStefano Babic2010-04-30-1/+1
| | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
| * MX25 print arm clock instead of mpllclk on bootJohn Rigby2010-04-30-1/+1
| | | | | | | | | | | | | | | | | | Replace call to imx_get_mpllclk with imx_get_armclk to show frequency of ARM core instead of mpll internal bus in print_cpuinfo. Signed-off-by: John Rigby <jcrigby@gmail.com> CC: Stefano Babic <sbabic@denx.de>
| * configs/openrd_base.h: reordered macrosFrans Meulenbroeks2010-04-30-2/+2
| | | | | | | | | | | | | | moved CONFIG_CMD_FAT to filesystem section swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
| * configs/sheevaplug: added a few additional commandsFrans Meulenbroeks2010-04-30-5/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch includes a few additional commands in the sheevaplug version of u-boot: - support for LONGHELP so you can get help messages - auto completion and command editing - ubi and mii support - ext2 filesystem (convenient if you have an ext2 from which you want to boot) - jffs2 and ubifs filesystems (if you want to use these in NAND) This also makes it more similar to openrd client. Side effect of this patch is that the code now needs 3 sectors i.s.o. 2 so an existing env is overwritten Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
| * Marvell GuruPlug Board SupportSiddarth Gore2010-04-30-0/+652
| | | | | | | | | | | | | | | | | | | | | | | | | | | | GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0 GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot References: http://www.globalscaletechnologies.com/t-guruplugdetails.aspx http://plugcomputer.org This patch is for GuruPlug Plus, but it supports Standard version as well. Signed-off-by: Siddarth Gore <gores@marvell.com>
| * Moved board specific values in config fileStefano Babic2010-04-30-1/+7
| | | | | | | | | | | | | | | | The lowlevel_init file contained some hard-coded values to setup the RAM. These board related values are moved into the board configuration file. Signed-off-by: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-12-23 14:57:56 +0000