summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* mmc: tegra: support Tegra124Stephen Warren2014-02-03-0/+11
| | | | | | | | | | | | | | | | | | | | | Tegra124's MMC controller is very similar to earlier SoC generations, and can be supported by the same driver. However, there are some non-backwards-compatible HW differences, and hence a new DT compatible value must be used to describe the HW. This patch updates the driver to support that new compatible value. That said, the HW differences are only relevant when enabling certain high-performance transfer modes. Since the driver is currently very simple and doesn't enable those modes, we don't actually need to address any of these HW differences in the code yet, hence the simple nature of this patch. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: don't exceed AVP limits when configuring PLLPJimmy Zhang2014-02-03-87/+118
| | | | | | | | | | | | | | | | | | | | | | | | Based on the Tegra TRM, the system clock (which is the AVP clock) can run up to 275MHz. On power on, the default sytem clock source is set to PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to 408MHz which is beyond system clock's upper limit. The fix is to set the system clock to CLK_M before initializing PLLP, and then switch back to PLLP_OUT4, which has an appropriate divider configured, after PLLP has been configured Implement this logic in new function tegra30_set_up_pllp(), which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP clock switching. Remove the duplicate PLLP setup from pllx_set_rate() and adjust_pllp_out_freqs(). Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com> [swarren, significantly refactored the change] Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: amend pmc.h for Tegra114+Stephen Warren2014-02-03-3/+7
| | | | | | | | | | | | | | | | | | | | Tegra114 and later's PMC module removes the pwrgate_timer_on register and replaces it with a clamp_status register. Adjust pmc.h to reflect this, and update any code affected by the change. The cpu.c change in this patch was extracted from a much larger patch by Jimmy Zhang. The pmc.h change was written from scratch, but inspired by related changes made by Tom Warren. There could well be other differences in the PMC register set for chips after Tegra20/30. However, they don't affect the code in U-Boot at present, so I haven't attempted an exhaustive update of pmc.h. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: implement MASK_BITS_31_29Tom Warren2014-02-03-4/+21
| | | | | | | | | | | | | Some clock sources have 3-bit muxes in bits 31:29. Implement core support for this mux field. Signed-off-by: Tom Warren <twarren@nvidia.com> [swarren, extracted from a larger patch by Tom] Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: MASK_BITS_ no longer needs specific valuesStephen Warren2014-02-03-1/+1
| | | | | | | | | | | | | | | | | | Since all code that sets or interprets MASK_BITS_* now uses the enums to define/compare the values, there is no need for MASK_BITS_* to have a specific integer value. In fact, having a specific integer value may encourage people to hard-code those values, or interpret the values in incorrect ways. As such, remove the logic that assigns a specific value to the enum values in order to make it completely clear that it's just an enum, not something that directly represents some integer value. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: use MASK_BITS_* macros everywhereStephen Warren2014-02-03-3/+3
| | | | | | | | | | | | | | | | | | | | | | Not all code that set or interpreted "mux_bits" was using the named macros, but rather some was simply using hard-coded integer constants. This makes it hard to determine which pieces of code are affected by changes to those constants. Replace the integer constants with the equivalent macro definitions so that everything is nicely tied together. Note that I'm not convinced all the code was using the correct integer constants, and hence I'm not convinced that all the code is now using the desired macros. However, this change is a purely mechanical replacement and should have no functional change. Fixing any bugs will come later, separately. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: rename OUT_CLK_SOURCE_*Stephen Warren2014-02-03-12/+13
| | | | | | | | | | | | | | | OUT_CLK_SOURCE_ are currently named after the number of bits the mask they represent includes. However, bit count is not the only possible variable; bit position may also vary. Rename OUT_CLK_SOURCE_ to OUT_CLK_SOURCE_31_30_ and OUT_CLK_SOURCE4_ to OUT_CLK_SOURCE_31_28 to more completely describe exactly what they represent, without having to go look up the definitions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: rename MASK_BITS_29_28 to MASK_BITS_31_28Stephen Warren2014-02-03-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | The only place where the MASK_BITS_* values are used is in adjust_periph_pll(), which interprets the value 4 (old MASK_BITS_29_28, new MASK_BITS_31_28) as being associated with mask OUT_CLK_SOURCE4_MASK, i.e. bits 31:28. Rename the MASK_BITS_ macro to reflect how it's actually implemented. Note that no Tegra clock register actually uses all of bits 31:28 as the mux field. Rather, bits 30:28, 29:28, or 28 are used. However, in those cases, nothing is stored in the bits above the mux field, so it's safe to pretend that the mux field extends all the way to the end of the register. As such, the U-Boot clock driver is currently a bit lazy, and doesn't distinguish between 31:28, 30:28, 29:28 and 28; it just lumps them all together and pretends they're all 31:28. This patch doesn't cause this issue; it was pre-existing. Hopefully, future patches will clean this up. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: deduplicate MASK_BITS_xxx clock mux enumTom Warren2014-02-03-12/+6
| | | | | | | | | | | | | | | The enum used to define the set of register bits used to represent a clock's input mux, MUX_BITS_*, is defined separately for each SoC at present. Move this definition to a common location to ease fixing up some issues with the definition, and the code that uses it. Signed-off-by: Tom Warren <twarren@nvidia.com> [swarren, extracted from a larger patch by Tom] Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: clear $usb_need_init each bootStephen Warren2014-02-03-0/+1
| | | | | | | | | | | | $usb_need_init prevents "usb start" from being run multiple times for each boot attempt, i.e. once for USB storage, another for PXE, and another for DHCP. However, the flag that's used to determine when to run "usb start" is never cleared, so a subsequent "boot" command will never probe for a freshly plugged in USB device. Fix this so that new USB devices will be probed once per boot attempt. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: set env vars to indicate Cardhu A04 supportStephen Warren2014-02-03-1/+10
| | | | | | | | | | | | | | | The U-Boot "cardhu" build supports only revision 4 of the Cardhu board and later compatible revisions. Hence, set $board_name in the default environment to "cardhu-a04" rather than just "cardhu". The Linux kernel has separate DTs for Cardhu A02 and A04, although the former isn't really supported any more. Consequently, the kernel DT file that matches the U-Boot cardhu build is "tegra30-cardhu-a04.dtb" rather than "tegra30-cardhu.dtb". Set the $fdtfile default environment variable to reflect this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: accept any SKU ID for most chipsStephen Warren2014-02-03-0/+2
| | | | | | | | | | | | | | | | | | For Tegra20, the SKU ID actually impacts how U-Boot programs the chip, and hence we need to explicitly know about each and every SKU ID in order to operate correctly. However, for Tegra30/114, this isn't the case. Rather than forcing each new user with a different SKU to manually add their SKU ID into the code, simply accept any SKU ID. If U-Boot ever starts e.g. programming maximal CPU clocks etc., we'll need to undo this, or make the default case map to conservative defaults, but for now it's likely the path to least support cost. Reported-by: Olof Johansson <olof@lixom.net> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-01-29-1144/+157
|\
| * am43xx_evm.h: Correct SPL max sizeTom Rini2014-01-24-1/+1
| | | | | | | | | | | | | | | | Upon further inspection of relevant parts of the architecture, the maximum SPL binary size is 220KiB. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
| * DRA7: add ABB setup for MPU voltage domainNishanth Menon2014-01-24-3/+20
| | | | | | | | | | | | | | | | | | Patch adds modification to shared omap5 abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain at OPP_NOM. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * DRA7: Add support for ES1.1 silicon ID codeNishanth Menon2014-01-24-3/+13
| | | | | | | | | | | | | | | | ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support for ES1.1 IDCODE change. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * ARM: AM335x: Enable DDR dynamic IO power downSatyanarayana, Sandhya2014-01-24-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables dynamically powering down the IO receiver when not performing a read on boards using DDR3. This optimizes both active and standby power consumption. This bit is not set on EVM SK and EVM 1.5 and later boards. Setting the same. This has been tested on PG2.0 EVM1.5, EVM1.2, EVM-SK, BBB. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
| * ARM: AM43xx: Enable DDR dynamic IO power down for DDR3Lokesh Vutla2014-01-24-1/+1
| | | | | | | | | | | | | | | | | | | | | | This patch enables dynamically powering down the IO receiver when not performing a read on DDR3 board. This optimizes both active and standby power consumption. This is derived from a patch that is done on AM335x[1] [1] http://arago-project.org/git/projects/?p=u-boot-am33x.git;a=commit;h=6a9ee4bc72ece53fabf01825605fba3d71d5feb2 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * OMAP3: igep00x0: Convert to ti_omap3_common.h.Enric Balletbò i Serra2014-01-24-180/+9
| | | | | | | | | | | | To reduce code duplication update omap3_igep00x0.h to use ti_omap3_common.h. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
| * TI: OMAP3: Create common config files for TI OMAP3 platforms.Enric Balletbò i Serra2014-01-24-0/+73
| | | | | | | | | | | | | | | | Create a new file, include/configs/ti_omap3_common.h, for everything common to the OMAP3 SoC leaving just the board specific part to board configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
| * ARM: OMAP3: Rename OMAP3_PUBLIC_SRAM_* to NON_SECURE_SRAM_*Enric Balletbò i Serra2014-01-24-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | Other TI processors like am33xx, omap4 and omap5 have called these variables as NON_SECURE_SRAM_*, shouldn't be a big problem rename these variables to be coherent. One reason more to rename these variables is to have the possibility of any OMAP3 board to use the ti_armv7_common.h include as the NON_SECURE_SRAM_END is used to define the CONFIG_SYS_INIT_SP_ADDR variable. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
| * TI: armv7: Do not define the number DRAM banks if is already defined.Enric Balletbò i Serra2014-01-24-3/+7
| | | | | | | | | | | | | | | | | | | | If CONFIG_NR_DRAM_BANKS is not defined, we say (for simplicity) that we have 1 bank, but for some boards should be interesting that we can define CONFIG_NR_DRAM_BANKS. To handle this possibility just define the number of DRAM banks if is not already defined. This is useful for some OMAP3 boards where the DRAM initialitzation is only at u-boot level. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
| * TI: armv7: Move ELM support to SoC configuration file.Enric Balletbò i Serra2014-01-24-1/+12
| | | | | | | | | | | | | | | | | | The ELM hardware engine wihich is used for ECC error detections is not present on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to SoC configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: OMAP5: Rename to ti_omap5_common.hEnric Balletbò i Serra2014-01-24-7/+7
| | | | | | | | | | | | | | | | Follow the pattern ti_<processor family>_common.h used by other TI processors to be coherent. So just rename omap5_common.h to ti_omap5_common.h. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: OMAP4: Rename to ti_omap4_common.hEnric Balletbò i Serra2014-01-24-7/+7
| | | | | | | | | | | | | | | | Follow the pattern ti_<processor family>_common.h used by other TI processors to be coherent. So just rename omap4_common.h to ti_omap4_common.h. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
| * feature-removal-schedule.txt: Drop CONFIG_SYS_ENABLE_PADS_ALL/CLOCKS_ENABLE_ALLTom Rini2014-01-24-16/+0
| | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| * ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALLJassi Brar2014-01-24-688/+0
| | | | | | | | | | | | | | | | | | The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
| * ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALLJassi Brar2014-01-24-227/+0
| | | | | | | | | | | | | | | | | | The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* | Merge branch 'u-boot-arm/next' into 'u-boot-arm/master'Albert ARIBAUD2014-01-28-1/+6
|\ \
| * | ARM: versatile: pass console setting to the kernelLinus Walleij2014-01-13-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Versatiles come up with the primary UART set to ttyAMA0 at 38400 baud, and unless we pass this to the kernel it will assume it is set to 9600 baud which will be quite awkward for the terminal, let's try to be helpful and inform the kernel what setting is used. Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | ARM: versatile: pass correct machine type for Versatile ABLinus Walleij2014-01-13-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When U-Boot is configured for Versatile AB, it will still pass the machine ID of Versatile PB to the kernel. After this simple fix the system boots correctly. Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* | | boards.cfg: Keep the entries sortedFabio Estevam2014-01-27-28/+28
| | | | | | | | | | | | | | | | | | | | | Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0.cfg boards.cfg" in order to keep the entries sorted. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | | board_r - fixup functions table after relocationAlexey Brodkin2014-01-27-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is only required for "PIC" relocation and doesn't apply to modern "PIE" relocation which does data relocation as well as code. "init_sequence_r" is just an array that consists of compile-time adresses of init functions. Since this is basically an array of integers (pointers to "void" to be more precise) it won't be modified during relocation - it will be just copied to new location as it is. As a consequence on execution after relocation "initcall_run_list" will be jumping to pre-relocation addresses. As long as we don't overwrite pre-relocation memory area init calls are executed correctly. But still it is dangerous because after relocation we don't expect initially used memory to stay untouched. Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Doug Anderson <dianders@chromium.org> Cc: Thomas Langer <thomas.langer@lantiq.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* | | arm: am43xx: Add USB spl boot supportDan Murphy2014-01-24-6/+40
| | | | | | | | | | | | | | | | | | | | | Add the USB host boot support for the am43xx evm Add the macros to boot from a usb drive in uBoot Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | | spl: common: Support for USB MSD FAT image loadingDan Murphy2014-01-24-11/+92
| | | | | | | | | | | | | | | | | | | | | | | | Add SPL support to be able to detect a USB Mass Storage device connected to a USB host. Once a USB Mass storage device is detected the SPL will load the u-boot.img from a FAT partition to target address. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | | spl: common: Move FAT funcs to a common fileDan Murphy2014-01-24-62/+108
| | | | | | | | | | | | | | | | | | Move the FAT functions to a common location for reuse. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | | powerpc: mpc5xxx: remove redundant CONFIG_MPC5xxx definitionMasahiro Yamada2014-01-24-61/+29
| | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_MPC5xxx in board config headers (and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | board: delete meaningless serial.hMasahiro Yamada2014-01-24-287/+0
| | | | | | | | | | | | | | | | | | | | | | | | Delete some serial.h files, whole code in which is surrounded by #if 0 ... #endif Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de>
* | | sandbox: fix the return type of os_free() functionMasahiro Yamada2014-01-24-2/+2
| | | | | | | | | | | | | | | | | | | | | The function os_free() returns nothing. Its return type should be "void" rather than "void *". Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | ARM: merge commonly-defined PLATFORM_RELFLAGSMasahiro Yamada2014-01-24-82/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8 had the same option: $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) This commit moves it into arch/arm/config.mk. If the compiler does not support the option, it is ignored by $(call cc-option,...). So this commit gives no harm to ARMv8. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc86xx: move CONFIG_MPC86xx definition to CPU config.mkMasahiro Yamada2014-01-24-5/+1
| | | | | | | | | | | | | | | | | | | | | Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk because all target boards with mpc86xx cpu define it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc85xx: move CONFIG_MPC85xx definition to CPU config.mkMasahiro Yamada2014-01-24-41/+1
| | | | | | | | | | | | | | | | | | | | | Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk because all target boards with mpc85xx cpu define it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc824x: remove redundant CONFIG_MPC824X definitionMasahiro Yamada2014-01-24-13/+0
| | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_MPC824X in board config headers because it is defined in arch/powerpc/cpu/mpc824x/config.mk. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc5xx: remove redundant CONFIG_5xx definitionMasahiro Yamada2014-01-24-2/+0
| | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_5xx in a source file because it is defined in arch/powerpc/cpu/mpc5xx/config.mk. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc512x: remove redundant CONFIG_MPC512X definitionMasahiro Yamada2014-01-24-5/+0
| | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_MPC512X in board config headers because it is defined in arch/powerpc/cpu/mpc512x/config.mk. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc8xx: remove redundant CONFIG_8xx definitionMasahiro Yamada2014-01-24-4/+0
| | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_8xx in source files because it is defined in arch/powerpc/cpu/mpc8xx/config.mk Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: mpc83xx: remove redundant CONFIG_MPC83xx definitionMasahiro Yamada2014-01-24-20/+0
| | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_MPC83xx in board config headers because it is defined in arch/powerpc/cpu/mpc83xx/config.mk. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | powerpc: ppc4xx: remove redundant CONFIG_4xx definitionMasahiro Yamada2014-01-24-78/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We do not have to define CONFIG_4xx in board config headers because it is defined in arch/powerpc/cpu/ppc4xx/config.mk. include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx". I believe it is a typo because "CONFIG_4x" is not used at all in other files. So, I also deleted "CONFIG_4x" in include/configs/JSE.h. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | board: tec-ng: Do not make directories in a board MakefileMasahiro Yamada2014-01-24-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e5c5301f refactored the build system not to make directories in board makefiles. But commit 8f380381 create directories again in board/avionic-design/tec-ng/Makefile. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Alban Bedel <alban.bedel@avionic-design.de>
* | | drivers: delete unused header filesMasahiro Yamada2014-01-24-1217/+0
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>