summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ARM64: zynqmp: Correct the sdhci minimum frequency for ep108Siva Durga Prasad Paladugu2016-11-15-1/+1
| | | | | | | | Correct the sdhci minimum frequency for ep platform. It should be right shift instead of left shift operand. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Ignore warnings from autogenerated filesMichal Simek2016-11-15-0/+12
| | | | | | | | Autogenerated files contain casting issues and missing function declaration and even usleep implementation. Suppress them for now till these files are fixed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Fix secondary bootmode enablingMichal Simek2016-11-15-2/+7
| | | | | | | | | | | | | Do not setup use_alt bit which copy alternative boot mode to boot mode. The reason is that this bit is cleared after POR but not after any software reset which will cause that after SW reset bootrom will look for different boot image. This patch setups alternative boot mode selection (purely SW handling) and extends code to read this alternative boot mode first and use it if it is setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Add support for SD1 with level shifters bootmodeSiva Durga Prasad Paladugu2016-11-15-0/+4
| | | | | | | Add support for SD1 with level shifters bootmode. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Record board name as serial number for DFU/FASTBOOTMichal Simek2016-11-15-0/+4
| | | | Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Adjust to new SMC interface to get silicon versionSoren Brinkmann2016-11-15-0/+17
| | | | | | | | | | The new FW interface returns the IDCODE and version register, leaving extracting bitfields to the caller. Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: Add support for Zynq 7000S 7007s/7012s/7014s devicesMichal Simek2016-11-15-0/+30
| | | | | | | Zynq 7000S (Single A9 core) devices is using different ID code. This patch adds this new codes and assign them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* net: zynq_gem: Correct SGMII enable bit settingSiva Durga Prasad Paladugu2016-11-15-1/+1
| | | | | | | | | Correct the SGMII enable bit position to 27 instead of 31. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* net: zynq_gem: Modify the nwcfg bit definitionsSiva Durga Prasad Paladugu2016-11-15-8/+8
| | | | | | | | | Modify the nwcfg bit definitions to have 32-bit by removing the extra nibble. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* nand: arasan_nfc: Clear ecc on bit while sending read commandSiva Durga Prasad Paladugu2016-11-15-0/+2
| | | | | | | | | | Clear ecc ON bit while sending read command as all types of read command(like reading spare) doesnt need ECC to be enabled. It has been anyway taken care in other places whereever required using arasan_nand_enable_ecc(). Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: nand: Runtime detection of nand buswidth through slcrMichal Simek2016-11-15-0/+25
| | | | | | | | | | | | | This patch adds support to check the buswidth on nand flash at runtime based on nand MIO configurations done by FSBL. User needs to correctly configure the MIO's based on the buswidth supported by the nand flash which is present on the board. Added nand8 and nand16 @periph names on slcr driver. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: nand: Enable Nand flash controller driver a zynq boardSiva Durga Prasad Paladugu2016-11-15-0/+9
| | | | | | | | Enable zynq Nand flash controller driver for a zynq ZC770 XM011(dc2) board. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* mtd: nand: zynq_nand: Add nand driver support for zynqSiva Durga Prasad Paladugu2016-11-15-0/+1194
| | | | | | | Add nand flash controller driver support for zynq SoC. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: Add support for the topic-miami system-on-modules and carrier boardsMike Looijmans2016-11-15-0/+1115
| | | | | | | | | | | | | | The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM, 32MB QSPI NOR flash and 256MB NAND flash. The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC, 2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources and a fan controller. The "Florida" carrier boards add SD, USB, ethernet and other interfaces. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: Make SYS_VENDOR configurableMike Looijmans2016-11-15-0/+1
| | | | | | | | Add a string description for SYS_VENDOR to allow configuring boards from other vendors than just "xilinx". Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* tools: mkimage: Check if file is regular fileMichal Simek2016-11-15-2/+8
| | | | | | | | | | | | Current Makefile.spl passes -R parameter which is not empty and pointing to ./ folder. "./tools/mkimage -T zynqmpimage -R ./"" -d spl/u-boot-spl.bin spl/boot.bin" That's why mkimage is trying to parse ./ file and generate register init which is wrong. Check that passed filename is regular file. If not do not work with it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* tools: mkimage: Add support for initialization table for Zynq and ZynqMPMike Looijmans2016-11-15-2/+72
| | | | | | | | | | | | | | | | | | The Zynq/ZynqMP boot.bin file contains a region for register initialization data. Filling in proper values in this table can reduce boot time (e.g. about 50ms faster on QSPI boot) and also reduce the size of the SPL binary. The table is a simple text file with register+data on each line. Other lines are simply skipped. The file can be passed to mkimage using the "-R" parameter. It is recommended to add reg init file to board folder. For example: CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* Prepare v2016.11Tom Rini2016-11-14-1/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* MAINTAINERS: mark sunxi status as OrphanHans de Goede2016-11-14-3/+1
| | | | | | | | | | | | Ian has not had any time for sunxi for some time now and I'm in the same situation now, so I'm stepping down as sunxi custodian and marking the sunxi support as Orphan. Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* video: bmp: Fix compilation errors with CONFIG_BMP_xxBPP enabledStefan Roese2016-11-13-3/+3
| | | | | | | | | | | | | | | | | | | | | Compiling the 'bmp' command with DM and having one of the following macros enabled: CONFIG_BMP_16BPP, CONFIG_BMP_24BPP ONFIG_BMP_32BPP generates this error: drivers/video/video_bmp.c: In function ‘video_bmp_display’: drivers/video/video_bmp.c:315:22: error: ‘lcd_line_length’ undeclared (first use in this function) fb -= width * 2 + lcd_line_length; ^ This patch moves to using the correct variable instead and enables the 'bmp' command for DM again. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
* net: write enetaddr down to hardware on env_callbackMarek Vasut2016-11-13-0/+1
| | | | | | | | | | | | If mac-address is changed using "setenv ethaddr ...." command the new mac-adress also must be written into the responsible ethernet driver. This fixes the legacy ethernet handling. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
* spi: ti_qspi: Fix baudrate divider calculationVignesh R2016-11-13-9/+7
| | | | | | | | | Fix the divider calculation logic to choose a value so that the resulting baudrate is either equal to or closest possible baudrate less than the requested value. While at that, cleanup ti_spi_set_speed(). Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* ARM: dts: dra7xx: Update spi-max-frequency for qspi slave nodeVignesh R2016-11-13-2/+2
| | | | | | | | | Update the spi-max-frequency property of m25p80 flash slave to match that of TI QSPI controller node, so that QSPI operations happen at maximum supported frequency of 76.8MHz. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* ARM: k2g: Update PLL Multiplier and divider valuesLokesh Vutla2016-11-13-1/+1
| | | | | | | | | | | Only a certain set of PLLM/D values are recommended to configure the DDR at the required speeds for a given clock input frequency. Updating these values as specified in Data Sheet[1] Table 5-18 [1] http://www.ti.com/lit/ds/symlink/66ak2g02.pdf Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: PLL: Enable glitch free initialization sequenceLokesh Vutla2016-11-13-8/+8
| | | | | | | | | | Update the PLL initialization sequence to avoid glitches while programming. User guide for the same is available at[1]. [1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* arm: Set TTB XN bit in case DCACHE_OFF for LPAE modeKeerthy2016-11-13-1/+6
| | | | | | | | | | | | | | | | | While we setup the mmu initially we mark set_section_dcache with DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro is rightly defined with TTB_SECT_XN_MASK set so as to mark all the 4GB XN. In case of LPAE mode XN(Execute-never) bit is not set with DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which keeps all the regions execute okay and this leads to random speculative fetches in random memory regions which was eventually caught by kernel omap-l3-noc driver. Fix this to mark the regions as XN by default. Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Tom Rini <trini@konsulko.com>
* arm: print the cache config option in hex instead of decimalKeerthy2016-11-13-1/+1
| | | | | | | Printing the option value in hex makes it more comprehensible. Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* mx6ull_14x14_evk: Add README fileDiego Dorta2016-11-13-0/+36
| | | | | | | | | Add a README file to help users getting started with the board. Signed-off-by: Diego Dorta <diego.dorta@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* davinci: omapl138_lcdk: keep booting even when MAC address is invalidFabien Parent2016-11-13-6/+8
| | | | | | | | | | | | If the MAC address specified on the EEPROM is invalid (multicast or zero address), then u-boot fails to boot. Having a bad MAC address in the EEPROM should not prevent the system from booting. This commit changes the error path to just print an error messages in case of bad MAC address. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: am335x/mux: Do not hang when encountering a bad EEPROMAlex G2016-11-13-2/+2
| | | | | | | | | | | | | | | | | | | | | In most cases, the SPL and u-boot.img will be on the same boot media. Since the SPL was loaded by the boot rom, the pinmux will already have been configured for this media. This, the board will still be able to boot successfully, or at least reach the u-boot console, where more recovery options are available. I've encountered this on a beaglebone black with a corrupted EEPROM. Removing this check allowed the board to boot successfully. I've also seen this on EVM-based boards with an unprogrammed EEPROM. On those boards, for some reason there were no UART messages. This made it look as if the SOC was dead. Remove the hang(), as it is not a fatal error. Also reformat the error message to be clearer as to the cause. The original message made it appear as if the wrong binary was being loaded. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* igep00x0: add Hynix timingsLadislav Michl2016-11-13-4/+16
| | | | | | | | | Tested on IGEPv2 with Micron MT29F4G16ABBDA3W and Hynix H27S4G6F2DKA-BM Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Javier Martinez Canillas <javier@samsung.com> Tested-by: Javier Martinez Canillas <javier@samsung.com>
* igep00x0: consolidate defconfigsLadislav Michl2016-11-13-36/+5
| | | | | | | | Defconfigs should remain the same except CONFIG_SYS_EXTRA_OPTIONS. Drop NAND specific defconfig as flash type is runtime detected. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Javier Martinez Canillas <javier@samsung.com>
* igep00x0: disable CONFIG_DISPLAY_BOARDINFOLadislav Michl2016-11-13-18/+3
| | | | | | | | | | | As a single U-Boot binary can now run on various board modifications, drop CONFIG_DISPLAY_BOARDINFO as it prints flash memory information too early to give us chance to easily detect it. Also saves few bytes as a bonus. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Javier Martinez Canillas <javier@samsung.com> Tested-by: Javier Martinez Canillas <javier@samsung.com>
* tools: fix mksunxiboot build for tools-all targetAndre Przywara2016-11-13-1/+1
| | | | | | | | | | | | Commit fed329aebe3a ("tools: add mksunxiboot to tools-all target") added mksunxiboot to the tools-all target, but used the CONFIG_SUNXI symbol to enable its build. Now commit aec9a0f19f64 ("sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI"), merged before that, renamed that symbol, so that the first patch basically gets ineffective. Adjust the symbol name in tools/Makefile to make it build again. Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini2016-11-08-32/+69
|\
| * ARM: tegra186: call secure monitor for all cache-wide opsStephen Warren2016-11-07-3/+21
| | | | | | | | | | | | | | | | | | An SMC call is required for all cache-wide operations on Tegra186. This patch implements the two missing hooks now that U-Boot supports them, and fixes the mapping of "hook name" to SMC call code. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * armv8: add hooks for all cache-wide operationsStephen Warren2016-11-07-11/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC-specific logic may be required for all forms of cache-wide operations; invalidate and flush of both dcache and icache (note that only 3 of the 4 possible combinations make sense, since the icache never contains dirty lines). This patch adds an optional hook for all implemented cache-wide operations, and renames the one existing hook to better represent exactly which operation it is implementing. A dummy no-op implementation of each hook is provided. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * ARM: tegra: translate __asm_flush_l3_cache to assemblyStephen Warren2016-11-07-23/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When performing a cache disable function, code must not access DRAM. That is because when the cache is disabled, it will be bypassed and all loads and stores will be serviced by RAM. This prevents accessing any dirty data in the cache. In turn, this means the stack cannot be used, since that is in RAM. To guarantee that code doesn't use RAM (and in particular the stack) __asm_flush_l3_cache() must be manually implemented in assembly, rather than implemented in C since the compiler won't know not to touch RAM. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * ARM: tegra: ensure nvtboot_boot_x0 alignmentStephen Warren2016-11-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | nvtboot_boot_x0 is a 64-bit variable and hence must be 64-bit aligned. So far this has happened by accident! Fix the code so this is guaranteed. This fixes the following build error: ... relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC against symbol `nvtboot_boot_x0' ... Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini2016-11-07-24/+1849
|\ \
| * | net: use random ethernet address if invalid and not zeroSiva Durga Prasad Paladugu2016-11-07-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use random ethernet address if the ethernet address found is invalid, not zero and config for random address is defined. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net: mvgbe: Fix build error with CONFIG_PHYLIBChris Packham2016-11-07-22/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 5a49f17481bb ("net: mii: Use spatch to update miiphy_register") updated the mvgbe implementation of smi_reg_read/smi_reg_write. Prior to that change mvgbe_phy_read and mvgbe_phy_write where used as wrappers to satisfy the phylib APIs. Because these functions weren't updated in that commit build errors where triggered when CONFIG_PHYLIB was enabled. Fix these build errors by removing mvgbe_phy_read and mvgbe_phy_write and using smi_reg_read/smi_reg_write directly. Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net: phy: micrel: center FLP burst timing at 16msAsh Charles2016-11-07-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms specified by the IEEE802.3 standard from the chip's default of 8ms. For more details, see the "Auto-Negotiation Timing" section of the KSZ9031RNX datasheet. [1] https://patchwork.kernel.org/patch/6558371/ Signed-off-by: Ash Charles <ash.charles@savoirfairelinux.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | ARM: tegra: enable Ethernet on p2771-0000Stephen Warren2016-11-07-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | Enable the Ethernet device in DT, provide board-specific configuration, and enable the driver in Kconfig. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | ARM: tegra: add DWC EQoS (ethernet) to Tegra186 DTStephen Warren2016-11-07-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | Tegra186 includes a Synopsys DWC EQoS (Ethernet) device. Add this to the Tegra186 SoC DT so that boards can make use of it. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | ARM: tegra: configure Ethernet address on Tegra186Stephen Warren2016-11-07-0/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Tegra186, the bootloader which runs before U-Boot passes the Ethernet MAC address to U-Boot using device tree. Extract this value and write it to the environment, so that the Ethernet uclass picks it up and uses it for the built-in Ethernet device. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | ARM: tegra: add SoC-level hook for board_late_init()Stephen Warren2016-11-07-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extend the Tegra186 implementation of board_late_init() to call a per-SoC "hook" function. This will allow SoC-specific (rather than Tegra-wide) functionality to be implemented without the core Tegra code needing to be aware of the details. While board186.c is currently only used for Tegra186, it should be applicable to any other future SoC, and perhaps its simple design could be back-ported to older SoCs in the future too. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net: add driver for Synopsys Ethernet QoS deviceStephen Warren2016-11-07-0/+1564
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver supports the Synopsys Designware Ethernet QoS (Quality of Service) a/k/a eqos IP block, which is a different design than the HW supported by the existing designware.c driver. The IP supports many options for bus type, clocking/reset structure, and feature list. This driver currently supports the specific configuration used in NVIDIA's Tegra186 chip, but should be extensible to other combinations quite easily, as explained in the source. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> # V1 Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | dt: net: add DWC EQoS bindingStephen Warren2016-11-07-0/+166
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which supports multiple options for bus type, clocking and reset structure, and feature list. This patch imports the binding from the Linux kernel, including my V3 patch to extend the binding to cover the Tegra186, which is applied for next-20160912. So far, my changes have been acked by Lars Persson, the original author of the binding. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | wandboard: Make Ethernet functional againFabio Estevam2016-11-06-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit ce412b79e7255770 ("drivers: net: phy: atheros: add separate config for AR8031") ethernet does not work on mx6sabresd. This commit correctly assigns ar8031_config() as the configuration function for AR8031 in the same way as done in the Linux kernel. However, on wandboard design we need some additional configuration, such as enabling the 125 MHz AR8031 output that needs to be done in the board file. This also aligns with the same method that the kernel performs the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
generated by cgit v1.1 at 2024-12-16 19:59:00 +0000