summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ARM: DRA7: Change configuration to prevent DDR reset control from EMIFNishanth Menon2015-06-19-4/+4
| | | | | | | | | | | | | | | | | | | | DRA7/AM57xx devices can be operated in many different configurations. When the SoC is supposed to support a configuration where low power mode state may involve the SoC completely powered off and DDR is in self refresh, SoC EMIF controller should not be the master of the reset signal and an external entity might be in control of things. The default configuration of Linux on TI evms involve not powering off the voltage rails (due to various reasons including reliability concerns) and must not allow DDR reset to be controlled by EMIF. On platforms where external entity might control the reset signal, this configuration will be a "dont care". Fixes: 536d87470869 ("ARM: DRA7: Update DDR IO registers") Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Brad Griffis <bgriffis@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ti: omap4: remove CONFIG_SPL_EXT_SUPPORT from ti_omap4_common.h since it is ↵Guillaume GARDET2015-06-19-3/+0
| | | | | | | | now in ti_armv7_common.h Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)Guillaume GARDET2015-06-19-0/+5
| | | | | | | | | Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B). Compilation tested on TI armv7 boards and OMAP boards from other vendors. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* arm, am33xx: update for siemens am335x based boardsHeiko Schocher2015-06-19-178/+428
| | | | | | | | | | | | | | | | | | | | | | | | | | | | updates for the siemens am335x based boards: - draco: add delay for DDR3 configuration - change MTD partition layout and add a possibility to redefine MTD layout in board header. - move ubi support to common header file - draco: improve dtb naming - draco: set CONFIG_SYS_CBSIZE to 1024 - add generic env based led Leds can now be defined in Environment - add generic env based dfu button Which gpio is used for the dfu button can be defined through the Environment - set MACH_TYPE only if defined - draco: increase CPU freq to 300MHz - Add time command to siemens am33xx boards - DDR3: increase default tRFC - draco: enable pullup for DFU and ERST pin - change print format DDR3 Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Heiko Schocher <hs@denx.de>
* common: cmd_part: start and size sub-commands introductionPaul Kocialkowski2015-06-19-1/+77
| | | | | | | | | | | | | | | This introduces the part start and part size sub-commands. The purpose of these is to store the start block and size of a partition in a variable, given the device and partition number. This allows reading raw data that fits a single partition more easily. For instance, this could be used to figure out the start block and size of a kernel partition when a partition table is present, given the partition number. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Stephen Warren <swarren@nvidia.com> [trini: Change "%lx" to LBAF] Signed-off-by: Tom Rini <trini@konsulko.com>
* common: cmd_part: Proper alignmentPaul Kocialkowski2015-06-19-1/+1
| | | | | | This fixes a misaligned declaration. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* keystone2: use correct EFUSE_BOOTROM fileds to configure speedVitaly Andrianov2015-06-19-6/+6
| | | | | | | | The get_max_arm_speed() and get_max_dev_speed() used wrong register fields to get the maximum speeds. This commit fixes the bug. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* CPCI4052: Remove CONFIG_SYS_LONGHELPTom Rini2015-06-18-1/+1
| | | | | | | | | | | | | | | | With the change to make sure that CONFIG_CMD_NET is enabled this board no longer fits into the linker script: powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723] powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724 powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0 LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec powerpc-linux-ld.bfd: final link failed: File truncated Drop CONFIG_SYS_LONGHELP to free up space. Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* spl: spl_mmc: MMC boot mode provisions checksPaul Kocialkowski2015-06-18-7/+15
| | | | | | | | | | | This allows using only one of either raw or fs mode for SPL mmc boot, without the need to have provisions for the other. In particular, a device may have U-Boot installed on a file system on the mmc, without ever needing to read U-Boot from raw memory. Thus, there is no reason to provide a sector or partition for raw mode. This allows this behaviour and still provides a robust fallback mechanism in case provisions for both modes are defined. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* spl: spl_mmc: Minor cosmeticsPaul Kocialkowski2015-06-18-6/+5
| | | | | | This switches some printf calls to puts and avoids a test repetition. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* tools/env/fw_env.h: Correct include orderPeter Robinson2015-06-18-1/+2
| | | | | | | | | | | | | | | When building tools-only (or env) we need to be sure that we do use <linux/kconfig.h> and do not use <generated/autoconf.h>. This will fix problems such as running 'make defconfig' or 'make sandbox_config' and then 'make tools-only'. Based on the responses below to the thread add linux/kconfig.h higher in the includes and drop the now unneeded autoconf.h lower down to ensure the default environment is included correctly http://lists.denx.de/pipermail/u-boot/2015-June/216849.html Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
* fix: samsung: common: autoboot.cmd: Correct itbcfg definitionŁukasz Majewski2015-06-18-1/+1
| | | | | | This fix is necessary to avoid booting the default ITB configuration. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* mmc_write.c: Make mmc_berase do 32bit safe 64bit mathTom Rini2015-06-18-1/+11
| | | | | | | | | | | | | | We want to see if the requested start or total block count are unaligned. We discard the whole numbers and only care about the remainder. Update the code to use div_u64_rem here and add a comment. Cc: Hans de Goede <hdegoede@redhat.com> Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Bernhard Nortmann <bernhard.nortmann@web.de> Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
* board/BuR/tseries: remove lpj= from environment-variableHannes Petermaier2015-06-18-1/+1
| | | | | | | | | | since we have now various processor-speeds it isn't useful anymore to preinitialize kernels-delay loop. Rather we want the kernel to calibrate it on every boot. This wastes around 80ms boottime but is compatible to all CPU-speeds. Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
* board/BuR/common: support timer5 for pwm-backlightHannes Petermaier2015-06-18-3/+11
| | | | | | | | | | in future we support yet another b&r am335x based board, where Timer 5 is wired to backlight-driver. So we introduce a new driver-type '2' to setup timer5 instead timer6. Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Simon Glass <sjg@chromium.org>
* ti: am335x/am437x/omap5 devices: Fix breakage when CONFIG_CMD_NET is not usedCooper Jr., Franklin2015-06-18-1/+2
| | | | | | | | | | | | Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set. This results in build errors which was first discovered when trying to run make env. By defining a blank NETARGS these errors can be avoided. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Tested-by: Maxin B. John <maxin.john@enea.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* boards: tam3517-common: enable gpmc prefetch modeJeroen Hofstee2015-06-18-0/+1
| | | | | | | | | | | | | | | Since the tam3517 base board has a 16bit wide nand connected to the gpmc, enable the prefetch mode, since that is now supported. Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Cc: pekon gupta <pekon@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Daniel Mack <zonque@gmail.com> Cc: Tapani Utriainen <tapani@technexion.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Tom Rini <trini@konsulko.com>
* mtd: OMAP: Enable GPMC prefetch mode for 16 bit accessJeroen Hofstee2015-06-18-10/+18
| | | | | | | | | | | | commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled prefetch mode for 8 bit nand access, this adds 16 bit as well. Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Cc: Daniel Mack <zonque@gmail.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap_gpmc: move prefetch out of CONFIG_NAND_OMAP_ELMJeroen Hofstee2015-06-18-109/+109
| | | | | | | | | | | | | The prefech mode is a feature of the gpmc, not the ELM. An am3517 does not have an elm, but can do prefeches, so move the code out of the CONFIG_NAND_OMAP_ELM ifdef. Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Cc: Daniel Mack <zonque@gmail.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Tom Rini <trini@konsulko.com>
* MSI_Primo81_defconfig: enable USB OTG port and keyboard supportKarsten Merker2015-06-17-0/+4
| | | | | | | | | | | | | | | The MSI Primo 81 is an Allwinner A31s-based tablet on which the OTG port is the only accessible USB interface. The existing defconfig had VGA console on the LCD enabled, but was missing keyboard support because the prerequisites for that (sunxi MUSB support and AXP221 GPIO support) had not been available before. All previously missing dependencies are available now, so this patch enables keyboard support and its prerequisites in the defconfig. Signed-off-by: Karsten Merker <merker@debian.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sun6i: cpu_reset: Do not return from cpu_reset()Hans de Goede2015-06-17-0/+1
| | | | | | | | | | | | Currently on sun6i after a "reset" the prompt returns and the user can even type stuff until the watchdog triggers and does the actual reset. This is somewhat unexpected behavior for the "reset" command, this commit adds an endless loop to wait for the watchdog to trigger so that we do not return to the prompt. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: musb: Remove unused sunxi_musb_exit methodHans de Goede2015-06-17-34/+0
| | | | | | | | | Remove the unused sunxi_musb_exit method, there is no code in u-boot calling the exit method, and our implementation was broken as it did not disable the clocks and asserted reset. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: musb: Do not fully reset the controler from sunxi_musb_disableHans de Goede2015-06-17-21/+31
| | | | | | | | | | | | | | Fully resetting the controller is a too big hammer, and the musb_core will then afterwards fail to communicate with any endpoints other then 0 as too much state was cleared. Instead report vbus low for 200ms which will effectively end the current session without needing to do a full reset. This fixes usb mass-storage devices no longer working after a "usb reset" Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* Merge git://git.denx.de/u-boot-usbTom Rini2015-06-15-13/+364
|\
| * samsung: common: add example boot scriptsPrzemyslaw Marczak2015-06-08-0/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds example scripts of boot.scr: - bootzimg.cmd - check if dtb exists and boot zImage - autoboot.cmd - check which image exists: Image.itb, zImage or uImage and optionally load fdt file for u/zImage The blank spaces are added to improve readability and can be removed before use mkimage. Required U-Boot environment variables: $boardname, $fdtfile, $console, $mmcbootdev, $mmcbootpart, $mmcrootdev, $mmcrootpart, $rootfstype. Making boot.scr from file.cmd: mkimage -C none -A arm -T script -d file.cmd boot.scr The Odroid XU3 default environment is ready for those boot scripts and the right script can be loaded by DFU. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * odroid-xu3: config: enable DFU/THOR/UMS by add configs and environmentPrzemyslaw Marczak2015-06-08-2/+86
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables all functions required to use DFU/THOR and UMS: - DWC3: core, gadget, Samsung DWC3 PHY - USB gadget: endpoint autoconf, downloader, DFU, THOR, UMS The CONFIG_EXTRA_ENV_SETINGS from exynos5-common.h is redefined and appended by dfu environment setting and some system settings. The boot is still using $distro_boot as previous. Signed-off-by: Inha Song <ideal.song@samsung.com> Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * usb: f_mass_storage: sleep_thread: decrease the interval for check ctrlc()Inha Song2015-06-08-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This change decreases the interval of calls to: - display busy indicator - check ctrlc() - check cable connection By this change, breaking the UMS command is more easy on Odroid XU3. Signed-off-by: Inha Song <ideal.song@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
| * smdk5420: board: add functions to init dfu environment settingsInha Song2015-06-08-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit extends SMDK5420 board's file by adding functions: - get_dfu_alt_system() - get_dfu_alt_boot() This allows setting the DFU environment by function set_dfu_alt_info() from: board/samsung/common/misc.c Signed-off-by: Inha Song <ideal.song@samsung.com> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * smdk5420: board: add functions required to enable USB DWC3Joonyoung Shim2015-06-08-8/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds implementation of function calls: - usb_gadget_handle_interrupts() - board_usb_init() Which allow enable USB DWC3 gadget for this board. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Inha Song <ideal.song@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * samsung: usb: phy: Support for DWC3 PHYLukasz Majewski2015-06-08-0/+95
| | | | | | | | | | | | | | | | | | | | | | New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have been added to u-boot to provide proper PHY handling at Exynos5 SoCs. This code is used thereafter in the board_usb_init() call. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de>
| * arm: exynos: USB3 PHY base definition for Exynos5 SoCsLukasz Majewski2015-06-08-1/+1
| | | | | | | | | | | | | | | | After that change it would be possible to call samsung_get_base_usb3_phy() function to get proper base address Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
| * drivers: usb: fsl: Return if USB_MAX_CONTROLLER_COUNT is incorrectNikhil Badola2015-06-07-1/+1
| | | | | | | | | | | | | | Return if USB_MAX_CONTROLLER_COUNT hence the index of the controller to be initialised is incorrect Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
* | Merge git://git.denx.de/u-boot-marvellTom Rini2015-06-15-12/+39
|\ \
| * | tools/kwboot: Add parameters to set delay and timeout via cmdlineStefan Roese2015-06-14-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To support the Armada 38x, new values for the request-delay and the response-timeout are needed. As the values already implemented in this tool (for Kirkwood and Armada XP) don't seem to work here. To make this more flexible, lets add make those 2 parameters configurable via the cmdline. Here the new parameters: -q <req-delay>: use specific request-delay -s <resp-timeo>: use specific response-timeout For the Marvell DB-88F6820 these values are known to work: One board: -q 2 -s 1 2nd board: -q 5 -s 5 So this seems to be even board specific. But with this patch now those values can be specified and tested via the cmdline. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Kevin Smith <kevin.smith@elecsyscorp.com> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Luka Perkov <luka.perkov@sartura.hr>
| * | arm: mvebu: Update CBAR with SOC regs baseKevin Smith2015-06-14-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | SMP-enabled Linux kernels read the CBAR register in CP15 to find the address of the SCU registers. After remapping internal registers, also update the CBAR so the kernel can find them. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Stefan Roese <sr@denx.de>
| * | arm: mvebu: Disable L2 cache before enabling d-cacheStefan Roese2015-06-14-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | L2 cache may still be enabled by the BootROM. We need to first disable it before enabling d-cache support. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
| * | tools/kwbimage.c: Correct header size for SPI bootKevin Smith2015-06-14-10/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If defined, the macro CONFIG_SYS_SPI_U_BOOT_OFFS allows a board to specify the offset of the payload image into the kwb image file. This value was being used to locate the image, but was not used in the "header size" field of the main header. Move the use of this macro into the function that returns the header size so that the same value is used in all places. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Stefan Roese <sr@denx.de>
* | | omap5: Exclude more environment from SPL buildsTom Rini2015-06-15-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | In the cases where we make use of environment in SPL we do not need these defaults compiled in and available. These are taking up space that in some cases now prevent linking, so drop. Signed-off-by: Tom Rini <trini@konsulko.com>
* | | board: add support for Vision System's Baltos Industrial PCYegor Yefremov2015-06-15-0/+1280
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Vision Systems's Baltos is based on AM335x SoC from Texas Instruments. This patch adds support such Industrial PCs in mainline u-boot. [ balbi@ti.com: updated original patch to current u-boot ] Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
* | | ARM: DRA7: emif: Fix DDR init sequence during warm resetLokesh Vutla2015-06-15-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after warm reset, emif needs to be configured to bring it back to a known state. So configure EMIF during warm reset. Reported-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | | avr32: move CONFIG_SYS_GENERIC_BOARD to KconfigMasahiro Yamada2015-06-15-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | Now all the AVR32 boards have been converted into Generic Board. Select it in Kconfig and clean up defines in header files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | | ARM: AM43x: Fix MAX_RAM_BANK_SIZELokesh Vutla2015-06-15-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf. But MAX_RAM_BANK_SIZE is defined as 1GB. Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx. Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | am33xx: Re-enable SW levelling for DDR2Tom Rini2015-06-15-40/+124
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The recent changes for hw leveling on am33xx were not intended for DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config value to check against. This lets us pass in the value we would use to configure, when we have not yet configured the board yet. In other cases update the call to be as functional as before and check an already programmed value in. Tested-by: Yan Liu <yan-liu@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | | ARM: BeagleBoard-x15: Enable i2c5 clocksLokesh Vutla2015-06-15-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | On AM57xx evm I2C5 is used to detect the LCD board by reading the EEPROM present on the bus. Enable i2c5 clocks to help that. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | am43xx_evm: Enable NAND bootTom Rini2015-06-15-2/+22
| | | | | | | | | | | | | | | | | | | | | | | | Enable booting from NAND on the am437xx-evm. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | am335x_evm: nand: Fix boot from NANDRoger Quadros2015-06-15-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | Use the correct partition names from with the Device Tree blob and the kernel is picked up. Also use partition name instead of number for the root filesystem in the kernel boot arguments. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | am335x_evm: am44xx_evm: dra7xx_evm: nand: Fix file-system partition nameRoger Quadros2015-06-15-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We almost always use UBIFS for user accessible NAND file systems and the UBIFS file system might contain more than one volume within the single NAND partition. The last NAND partition is therefore more appropriately named as "NAND.file-system" instead of "NAND.rootfs" The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the last NAND partition. This patch makes the partition name consistent between u-boot and the kernel. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | configs: am43xx_evm: Enable NANDRoger Quadros2015-06-15-1/+1
| | | | | | | | | | | | | | | | | | | | | AM43xx EVMs have NAND so enable it. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | highbank: add custom ahci_link_up functionMark Langsdorf2015-06-15-1/+231
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Calxeda highbank SOC needs a custom sequence to bring up SATA links, so override ahci_link_up with custom function to handle combophy setup. Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com> Signed-off-by: Richard Gibbs Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Andre Przywara <osp@andrep.de>
* | | ahci: extend data io wait to 10sMark Langsdorf2015-06-12-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AHCI driver currently waits 5s before timing out when sending a data command to a drive. Some drives take upwards of 8s to respond to the initial data command while they're spinning up. Increase the data io timeout to 10s so that those drives can be found on initial scsi scan. Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com> Signed-off-by: Andre Przywara <osp@andrep.de>
generated by cgit v1.1 at 2024-12-17 02:20:50 +0000