summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* sunxi_nand_spl: Turn off clocks when we're done with the nandHans de Goede2015-08-31-2/+15
| | | | | | | | | | | | Turn off the nand and dma clocks when we're done with the nand, this puts the nand and dma controllers back into a clean state for when the kernel boots. Without this the kernel will not boot properly when it is built with dma-controller support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi_nand_spl: Make sure the DMA controller is enabledHans de Goede2015-08-31-0/+6
| | | | | | | | We use DMA for nand data transfers in the SPL, so make sure the DMA controller is enabled. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessaryHans de Goede2015-08-31-5/+10
| | | | | | | | Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are actually using the nand. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi_nand_spl: Do not bother writing the spare-area reg in syndrome modeHans de Goede2015-08-31-4/+1
| | | | | | | | | | | | In syndrome mode we set the NFC_SEQ bit in the command register, so the spare-area register is not used. Also the value currently being written is actual wrong, the ecc sits at "column + CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE" not just CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE. So the current code only serves to confuse the user -> remove it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi_nand_spl: We only need to reset the nand chip onceHans de Goede2015-08-31-10/+10
| | | | | | | There is no need to reset the nand chip for every ecc-block read. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi_nand_spl: Drop unnecessary temp bufHans de Goede2015-08-31-27/+8
| | | | | | | | | | | | | | | | | nand_spl_load_image() always gets called with either CONFIG_SYS_TEXT_BASE or spl_image.load_addr as destination, both of which are properly aligened, and have plenty of space for "overshooting" up to CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes, as we read in CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes chunks. This saves CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE (typically 1k) in SPL size, which is a lot on the total 24k we have. Note this changes the dma destination from SRAM to DRAM, so this patch updates the DDMA_DST_TYPE bits in the dma controller cfg0 reg accordingly. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi_nand_spl: Fix CONFIG_SPL_NAND_SUNXI handlingHans de Goede2015-08-31-6/+1
| | | | | | | | | | CONFIG_SPL_NAND_SUPPORT gets used via IS_ENABLED so it must be defined to 1, rather then just being defined. While at remove 2 other unused NAND related defines from sunxi-common.h. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add CONFIG_MMC0_CD_PIN to various boardsHans de Goede2015-08-31-0/+6
| | | | | | | | | Add CONFIG_MMC0_CD_PIN to various boards, this stops the SPL from still trying to access the sdcard when there is none (e.g. when booting from nand). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Drop LCD_MODE from A13-OLinuxIno defconfigsHans de Goede2015-08-31-2/+1
| | | | | | | | | | | | | | | | | | | With the unified / cleaned up default display output selection changes, which were done as part of adding composite video out support, our example LCD_MODE line in the A13-OLinuxIno defconfigs causes the display code to setup a LCD console by default, rather then a VGA console. Given that the LCD console is only useful for people who have hooked up the exact lcd-panel from the config, while most people will not have any lcd panel connected to these boards, this is not a good default. Dropping the LCD_MODE line which was intended as an example fixes this, instead add a link to the LCD_MODE help text pointing to http://linux-sunxi.org/LCD which contains the removed and other example modes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: musb: Drop no longer accurate comment in Kconfig help textHans de Goede2015-08-31-3/+1
| | | | | | | | | Drop the no longer accurate part of the USB_MUSB_SUNXI Kconfig help text, since the musb-host code now supports the device-model, ehci and musb in host mode can both be enabled at the same time without issues. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add support for gt90h-v4 tabletsHans de Goede2015-08-31-0/+173
| | | | | | | | | | | | | | | The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot. The pmic setup on this board is somewhat special, dcdc2 MUST be set to 1.1V instead of the usual 1.2V otherwise the board is very unstable. aldo1 is used to power the micro sd slot, dldo1 is used for wifi. This commit adds a defconfig + dts (as submitted to the kernel) for the gt90h-v4 pcb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp221: Allow specifying dcdc2 voltage via KconfigHans de Goede2015-08-31-1/+10
| | | | | | | | Allow specifying the axp221 dcdc2 voltage via Kconfig, this is necessary because on some boards the 1.2V default does not work reliable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: dts: uniphier: add ProXstream2 and PH1-LD6b SoC/board supportMasahiro Yamada2015-08-31-2/+334
| | | | | | | | | | | | | | Initial version of DTSI for ProXstream2 and PH1-LD6b and DTS for PH1-LD6b reference board. Import from Linux with some adjustments: - Use SPDX-License-Identifier - Add clock-frequency to serial nodes - Drop unusable nodes from -ref.dts While I am here, sort Makefile entries alphabetically. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: dts: uniphier: add PH1-Pro5 SoC supportMasahiro Yamada2015-08-31-0/+216
| | | | | | | | Initial version of UniPhier PH1-Pro5 device tree. (Imported from Linux with adjustment for SPDX License Identifier) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: dts: uniphier: sync with LinuxMasahiro Yamada2015-08-31-107/+472
| | | | | | | This commit imports device tree updates from Linux. It eventually adds pinctrl-related nodes and properties. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* serial: uniphier: drop platform data supportMasahiro Yamada2015-08-31-44/+15
| | | | | | | | | | This driver is enabled only for UniPhier SoCs and ARCH_UNIPHIER now selects OF_CONTROL and SPL_OF_CONTROL. This driver no longer needs to support platform data configuration. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* ARM: uniphier: enable SPL_OF_CONTROLMasahiro Yamada2015-08-31-67/+31
| | | | | | | | | | | | | Device Tree really improves code maintainability and is now available for SPL too. This is the state-of-the-art implementation in U-boot. The board files (platform data) are no longer needed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
* ARM: uniphier: select SPL_DM rather than default in defconfigMasahiro Yamada2015-08-30-4/+1
| | | | | | Now UniPhier SoCs highly depend on Driver Model for SPL, too. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove unused macroMasahiro Yamada2015-08-30-2/+0
| | | | | | This macro is not referenced at all. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: fix build error when CONFIG_DEBUG_LL is definedMasahiro Yamada2015-08-30-0/+2
| | | | | | | The build error happens if CONFIG_DEBUG_LL and CONFIG_MACH_PH1_SLD3 are both enabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mtd: denali_spl: do not allocate page_buffer in .bss sectionMasahiro Yamada2015-08-30-20/+12
| | | | | | | | | | | | | | | | | | | Since commit 2580a2a7e719 ("mtd: nand: Increase max sizes of OOB and Page size"), three boards (ph1_ld4, ph1_pro4, ph1_sld8) fail to build with the following error message: arm-linux-gnueabi-ld.bfd: SPL image plus BSS too big They compile drivers/mtd/nand/denali_spl.c and it has a page_buffer as static data: static uint8_t page_buffer[NAND_MAX_PAGESIZE]; This buffer required 8KB in .bss section before that commit and now it has been increased to 16KB. Given limited code/memory size for SPL, it is not a good idea to allocate a page buffer statically. In the first place, the load address 'dst' can be used as a page buffer. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* tools/atmelimage.c: Fix warning when debug is enabledTom Rini2015-08-28-1/+1
| | | | | | | | | | Otherwise we get: tools/atmelimage.c:134:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘size_t’ [-Wformat=] debug("atmelimage: interrupt vector #%d is 0x%08X\n", pos+1, ^ Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP5/AM43xx: remove enabling USB clocks from enable_basic_clocks()Kishon Vijay Abraham I2015-08-28-42/+0
| | | | | | | | | | Now that we have separate function to enable USB clocks, remove enabling USB clocks from enable_basic_clocks(). Now board_usb_init() should take care to invoke enable_usb_clocks() for enabling USB clocks. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: invoke clock API to enable and disable clocksKishon Vijay Abraham I2015-08-28-0/+10
| | | | | | | | invoke enable_usb_clocks during board_usb_init and disable_usb_clocks during board_usb_exit to enable and disable clocks respectively. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: AM43xx: Add functions to enable and disable USB clocksKishon Vijay Abraham I2015-08-28-0/+73
| | | | | | | | | | | Added functions to enable and disable USB clocks which can be invoked during USB init and USB exit respectively. Cc: Roger Quadros <rogerq@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP5: Add functions to enable and disable USB clocksKishon Vijay Abraham I2015-08-28-0/+101
| | | | | | | | | | | Added functions to enable and disable USB clocks which can be invoked during USB init and USB exit respectively. Cc: Roger Quadros <rogerq@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: OMAP5: added USB initializtion codeKishon Vijay Abraham I2015-08-28-0/+81
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in omap5 board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: beagle_x15: added USB initializtion codeKishon Vijay Abraham I2015-08-28-1/+112
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in beagle_x15 board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include: configs: am43xx_evm: add 'usb stop' in usbboot envKishon Vijay Abraham I2015-08-28-0/+2
| | | | | | | | | | | | The usbboot environment variable has 'usb start' command but doesn't have the corresponding 'usb stop' command. This breaks usb peripheral mode if tried after 'run usbboot' fails to load the images in usb host mode. Fix it here by adding 'usb stop' command in usbboot env. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: remove duplicate initialization of vbus_id_statusKishon Vijay Abraham I2015-08-28-4/+0
| | | | | | | | vbus_id_status is initialized in board_usb_init. So remove it while creating dwc3_device objects. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* TI PHY: Add support to control 2nd USB PHY in DRA7xx/AM57xxKishon Vijay Abraham I2015-08-28-4/+11
| | | | | | | | Added support to power on/power off the second USB PHY present in DRA7xx and AM57xx. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Enable clocks for USB OTGSS2 and USB PHY2Kishon Vijay Abraham I2015-08-28-0/+23
| | | | | | | | Enabled clocks for the second dwc3 controller and second USB PHY present in DRA7. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* usb: dwc3: dwc3-omap: Use the clear register inorder to clear the interruptsKishon Vijay Abraham I2015-08-28-18/+28
| | | | | | | | | | Writing "0x00" to the USBOTGSS_IRQENABLE_SET_MISC and USBOTGSS_IRQENABLE_SET_0 doesn't disable the interrupts. Used USBOTGSS_IRQENABLE_CLR_MISC and USBOTGSS_IRQENABLE_CLR_0 instead. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
* Makefile: fix SOURCE_DATE_EPOCH for *BSD hostAndreas Bießmann2015-08-28-3/+15
| | | | | | | | | | | | | | | | | | | The SOURCE_DATE_EPOCH mechanism for reproducible builds require some date(1) with -d switch to print the relevant date and time strings of another point of time. In other words it requires some date(1) that behaves like the GNU date(1) [1]. The BSD date(1) [2] on the other hand has the same switch but with a different meaning. Respect this and check the date(1) abilities before usage, error on non working version. Use the well known pre- and suffixes for the GNU variant of a tool on *BSD hosts to search for a working date(1) version. [1] http://man7.org/linux/man-pages/man1/date.1.html [2] http://www.freebsd.org/cgi/man.cgi?query=date Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* picosam9g45: adopt CONFIG_SYS_PROMPTAndreas Bießmann2015-08-28-1/+1
| | | | | | | | Commit 181bd9dc61d2da88b78f1c1138a685dae39354d6 introduced Kconfig selection for SYS_PROMPT. When applying the new picosam9g45 board this change slipped through, adopt it. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91sam9260ek: add missing files to MAINTAINERSAndreas Bießmann2015-08-28-0/+1
| | | | | | | | | | | This fixes the following genboardscfg.py warnings: ---8<--- WARNING: no status for 'at91sam9g20ek_2mmc' WARNING: no maintainers for 'at91sam9g20ek_2mmc' --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91sam9rlek: add missing files to MAINTAINERSAndreas Bießmann2015-08-28-0/+1
| | | | | | | | | | | This fixes following genboardscfg.py warning: ---8<--- WARNING: no status for 'at91sam9rlek_mmc' WARNING: no maintainers for 'at91sam9rlek_mmc' --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* omap-common: SYS_BOOT fallback logic correction and support for more devicesPaul Kocialkowski2015-08-28-10/+22
| | | | | | | | | | | | | | | | | | | | | The SYS_BOOT-based fallback shouldn't only check for one of the conditions of use and then let the switch/case handle each boot device without enforcing the conditions for each type of boot device again. For instance, this behaviour would trigger the fallback for UART when BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not CONFIG_SPL_USB_SUPPORT. Separating the logic for USB and UART solves this. In addition, this adds support for more peripheral devices (USBETH and CPGMAC) to the fallback mechanism. Note that the USBETH boot device should always be different from the USB boot device (each should match a different bootrom handoff case). Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
* mtd/nand/ubi: assortment of alignment fixesMarcel Ziswiler2015-08-28-7/+19
| | | | | | | | | | | | | | Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer alignment into account which led to failures of the following form: ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108 ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108 Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Scott Wood <scottwood@freescale.com> [trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h] Signed-off-by: Tom Rini <trini@konsulko.com>
* arm: spear: Some changes / updates to the x600 config headerStefan Roese2015-08-28-5/+16
| | | | | | | | | | | | | | | This patch brings the following changes to the x600 board support: - Add USB EHCI support - Add VFAT support for USB key file access - Increase malloc size (for UBI / UBIFS usage) - Enable Thumb mode to save some image space - Remove unreferenced CONFIG_STACKSIZE - Remove unreferenced CONFIG_SPL_NO_PRINTF Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com>
* arm: spear: Enable caches on SPEArStefan Roese2015-08-28-0/+10
| | | | | | | | | | | The designware ethernet driver supports d-cache now. So there is nothing stopping us now to enable the caches completely on SPEAr. Tested on SPEAr600 x600 board. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com>
* arm: spear: Move to common SPL infrastructureStefan Roese2015-08-28-271/+85
| | | | | | | | | | | | | The SPL implementation for SPEAr600 is older than the common SPL infrastructure. This patch now moves the SPEAr600 SPL over to the common SPL code. Tested on the only SPEAr board that currently uses SPL in mainline U-Boot, the x600. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com>
* arm: spear: Fix booting - relocate vector table to 0 (low-vector)Stefan Roese2015-08-28-5/+0
| | | | | | | | | | | | Booting SPEAr600 eval board doesn't work with current mainline U-Boot. With this patch the low-vector bit is left to '0'. Resulting in the common relocation of the vectors to 0 (SDRAM) to work correctly. Tested on the SPEAr600 EVB. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com>
* ARM: k2l: Fix device speedsLokesh Vutla2015-08-28-3/+3
| | | | | | | | | | | ARM supported speeds and init value of core_pll for SDP1200 are programmed wrong as part for the device speed cleanups. Fixing it here. Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection") Tested-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Update READMELokesh Vutla2015-08-28-11/+15
| | | | | | | Update README to include uart boot mode support and makefile changes. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Build MLO by defaultLokesh Vutla2015-08-28-0/+4
| | | | | | | | | | | MLO(NAND/MMC boot image), is used for all the ks2 platforms. Enabling it in config.mk so that these images will be automatically built upon calling make. u-boot-spi.gph is already the build target, so not including here. Reported-by: Nishanth Menon <nm@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Rename u-boot-nand.gph to MLOLokesh Vutla2015-08-28-7/+9
| | | | | | | | | | | | | | NAND boot mode, ROM expects an image with a gp header in the beginning and an 8bytes filled with zeros at the end. The same is true for SD boot on K2G platforms but the file name should be MLO. Renaming u-boot-nand.gph to MLO, so that same image can be used for NAND and SD boots. And also not including all the u-boot only images under CONFIG_SPL_BUILD. Reported-by: Nishanth Menon <nm@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: move the custom build rules out to keystone specific makefileNishanth Menon2015-08-28-16/+22
| | | | | | | | | | | | | | | Keystone has build rules introduced by commit ef509b9063fb7 ("k2hk: add support for k2hk SOC and EVM") and commit 0e7f2dbac6ead ("keystone: add support for NAND gpheader image"). These are not reused by other platforms for the build, hence there is no clear benefit is maintaining them in the generic makefile as a build target. move these to the keystone specific make option Original idea of using config.mk by Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: configs: Move SP to end of u-boot sectionLokesh Vutla2015-08-28-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Currently u-boot stack is defined at the beginning of MSMC RAM. This is a problem for uart boot mode as ROM downloads directly to starting of MSMC RAM. Fixing it by moving stack to the end of u-boot section and shifting SYS_TEXT_BASE to the start of MSMC RAM. Updated division of MSMC RAM is shown below: ----------------------------------------- | | | | | U-Boot text |U-Boot | SPL text | | download | Stack | Download + | | | | SPL_BSS + | | | | SPL_STACK | ----------------------------------------- [1] [2] [3] [4] [1] SYS_TEXT_BASE (Start of MSMC RAM) [2] SPL_TEXT_BASE - GBL_DATA_SIZE [3] SPL_TEXT_BASE [4] END of SPL [1] + [2] is at least 1M on all platforms, so no chance of overlap. Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* env_mmc: Properly prefix mmc errors with '!'Hans de Goede2015-08-28-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | The set_default_env() function from env_common.c expects either a fully formatted error msg, e.g.: "## Resetting to default environment\n" or an error msg prefixed with an !, in which case it will format it. Fix the init_mmc_for_env() error messages to be prefixed with a ! this changes the bootup-log on sunxi when no mmc card is found from: MMC: SUNXI SD/MMC: 0 No MMC card foundIn: serial Out: serial To: MMC: SUNXI SD/MMC: 0 *** Warning - No MMC card found, using default environment In: serial Out: serial Which clearly is how things should look. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit v1.1 at 2024-12-24 01:36:52 +0000