summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* mx6: Distinguish mx6dual from mx6quadFabio Estevam2014-02-11-3/+14
| | | | | | | | | | | | Currently when we boot a mx6dual U-boot reports that it is a mx6quad. Report it as MX6D instead: CPU: Freescale i.MX6D rev1.2 at 792 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* imx: Introduce a header for the imx cpu versionsFabio Estevam2014-02-11-13/+14
| | | | | | | Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header files, introduce a common header to centralize such definitions. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* hummingboard: Return from cpu_eth_init() directlyFabio Estevam2014-02-11-5/+1
| | | | | | | | | | There is no need to print an error message when cpu_eth_init() fails because net/eth.c already prints it. In order to simplify the code, just return the value from cpu_eth_init(bis) directly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failureAnson Huang2014-02-11-0/+11
| | | | | | | | | Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2), it will cause warm reset fail, need to clear this MMDC_CHx_MASK field to make sure all the i.MX6 series SOCs reset function work. Otherwise, uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2. Signed-off-by: Anson Huang <b20788@freescale.com>
* imx6: ensure AHB clock is 132MHz in low freq boot modeAnson Huang2014-02-11-0/+20
| | | | | | | | | | | | For low freq boot mode(ARM boot up with 396MHz), ROM will not set AHB clock to 132MHz, and the reset value of AHB divider is incorrect which will lead to wrong AHB rate, need to correct it. To enable low freq boot mode, need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL SabreSD board and i.MX6SL EVK board. Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Anson Huang <b20788@freescale.com>
* mx6sl: Adjust fdt_addr to avoid address overlappingFabio Estevam2014-02-11-1/+1
| | | | | | | | | Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading address to avoid overlaping), we need to adjust the fdt_addr in order to be able to boot FSL 3.10 kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* vf610twr: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* udoo: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx6slevk: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx6sabre_common: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx6qarm2: Set default environment to use zImageOtavio Salvador2014-02-11-5/+5
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx53loco: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx51evk: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx28evk: Set default environment to use zImageOtavio Salvador2014-02-11-13/+13
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx23evk: Set default environment to use zImageOtavio Salvador2014-02-11-6/+6
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* hummingboard: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* cgtqmx6eval: Set default environment to use zImageOtavio Salvador2014-02-11-7/+7
| | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* ARM: m53evk: Enable CONFIG_REGEXMarek Vasut2014-01-26-0/+2
| | | | | | | | Enable CONFIG_REGEX on M53EVK to allow usage of regular expressions on environment variables. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* ARM: m53evk: Rename mxc-nand to mxc_nandMarek Vasut2014-01-26-2/+2
| | | | | | | | | The name the Linux kernel expects is 'mxc_nand' , not 'mxc-nand' . This patch renames the driver name. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* nitrogen6x: README: Do not refer to MAINTAINERS fileFabio Estevam2014-01-26-1/+1
| | | | | | | | | MAINTAINERS file has been removed from the project. Replace its reference with 'boards.cfg' file instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
* nitrogen6x: README: Only calling 'make' is enoughFabio Estevam2014-01-26-1/+1
| | | | | | | | No need to pass 'u-boot.imx' as parameter for 'make' because u-boot.imx is built by default. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
* ARM: mx6: Enable PCIe on SabreliteMarek Vasut2014-01-26-0/+11
| | | | | | | | | | Enable PCI express on MX6 Sabrelite. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* ARM: mx6: Add PCI express driverMarek Vasut2014-01-26-0/+593
| | | | | | | | | | | | Add PCIe driver for the Freescale i.MX6 SoC . This driver operates the PCIe block in RC mode only, the EP mode is NOT supported. The driver is tested with the Intel e1000 NIC driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* ARM: mx6: Add PCI express clock configurationMarek Vasut2014-01-26-10/+66
| | | | | | | | | | | | | | | | Split the SATA clock enabling function and add PCI express clock enabling function. The SATA clock enabling function starts up the 100MHz SATA reference PLL in ENET_PLL register, but the code can be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull this code into separate function. Moreover, add the PCIe clock enabling code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* ARM: armv7: Make indirect vector addresses globlMarek Vasut2014-01-26-0/+7
| | | | | | | | | | | | | Make indirect vectors addresses global, so they can be replaced by various code that needs to do so. For example the MX6 PCI express driver needs to temporarily replace data abort handler when reading the config space. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2014-01-26-4489/+8008
|\
| * arm: koelsch: Add support QSPI device and enable boot from SPI flashNobuhiro Iwamatsu2014-01-16-4/+28
| | | | | | | | | | | | | | | | This supports SH-QSPI device on koelsch board, and enable booting from SPI flash. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: lager: Add support QSPI device and enable boot from SPI flashNobuhiro Iwamatsu2014-01-16-4/+29
| | | | | | | | | | | | | | | | This supports SH-QSPI device on lager board, and enable booting from SPI flash. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * spi: sh_qspi: Add header file that defines the address of registersNobuhiro Iwamatsu2014-01-16-1/+2
| | | | | | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Add SH QSPI base register addressNobuhiro Iwamatsu2014-01-16-0/+2
| | | | | | | | | | | | | | | | This adds base register address of SH QSPI. Currently, SH QSPI is used only from R8A7790 and R8A7791. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: lager: Disable TMU0 before OS bootNobuhiro Iwamatsu2014-01-16-0/+6
| | | | | | | | | | | | | | | | | | On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel and other. This disables TMU0 at the request of from kernel user. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: koelsch: Disable TMU0 before OS bootNobuhiro Iwamatsu2014-01-16-0/+6
| | | | | | | | | | | | | | | | | | On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel and other. This disables TMU0 at the request of from kernel user. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-01-15-3/+691
| |\
| * | arm: use canonical sub mnemonicAndreas Bießmann2014-01-14-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building some arm boards with older binutils may produce errors like this: ---8<--- crt0.S: Assembler messages: crt0.S:70: Error: register expected, not '#(184)' -- `sub sp,#(184)' --->8--- Use canonical version of the subtract mnemonic to avoid those issues. Reported-by: Alexey Smishlayev <alexey@xtech2.lv> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | Merge 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-01-14-53/+45
| |\ \
| * | | arm: put .hash, .got.plt and .machine_param back in binariesAlbert ARIBAUD2014-01-14-4/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some targets will build fine but not boot if sections .hash and .got.plt are not present in the binary. Add them back. Also, Exynos machines require .machine_param section in SPL. Add it. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
| * | | mx1ads: remove board supportAlbert ARIBAUD2014-01-14-733/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | mini2440: remove board supportAlbert ARIBAUD2014-01-14-301/+3
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | ARM: pxa: Fix OneNAND window access on VPAC270Marek Vasut2014-01-13-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Access the OneNAND 1KiB window on the VPAC270 as an SRAM instead of accessing it as a burst-RAM. This fixes a problem where the board failed to reboot sometimes as the CPU couldn't start executing from the OneNAND 1KiB window. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com>
| * | | ARM: pxa: Fix OneNAND SPL buildsMarek Vasut2014-01-13-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The OneNAND SPL used on PXA is slightly obscure. Due to the OneNAND limitation, where we have only the first 1KiB of the OneNAND available upon power-up as a memory-mapped area, from which the CPU starts executing, we place only the most essential code into this first 1KiB . This code copies the rest of the SPL into SRAM and jumps to it. This code is stored in section .text.0 . The rest of the SPL is stored in section .text.1 . When running the OBJCOPY on the SPL, it will preserve only .text section, but the .text.0 and .text.1 are stripped away from the result, thus making the SPL binary empty. The patch adds additional -j parameters to the OBJCOPY for PXA during the SPL build, which will preserve the .text.0 and .text.1 sections. Moreover, this patch also adds missing functions into the .text.0 section, since otherwise the PXA270 with 1KiB-window OneNAND won't be able to boot. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com>
| * | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-01-10-6629/+14927
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be added to include/configs/exynos5-dt.h now. Conflicts: include/configs/exynos5250-dt.h Signed-off-by: Tom Rini <trini@ti.com>
| | * | | doc: Update the zynq u-boot statusJagannadha Sutradharudu Teki2014-01-10-8/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Updated doc/README.zynq to current status Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | zynq: Enable CONFIG_DEFAULT_DEVICE_TREEJagannadha Sutradharudu Teki2014-01-10-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enabled default dts files on respective pre-board config files this is way MAKEALL will works. and it's upto user to build specific dts by specifying at build time. $ make zynq_zc70x_config $ make --> with default dts zynq-zc702.dts or $ make DEVICE_TREE=zynq-zc702 --> Same configuration with zynq-zc706.dts Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | dts: zynq: Add more zynq dts filesJagannadha Sutradharudu Teki2014-01-10-0/+84
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds initial dts support for supported zynq boards. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | zynq-common: Enable verified boot(RSA)Jagannadha Sutradharudu Teki2014-01-10-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_FIT_SIGNATURE - signature node support in FIT image CONFIG_RSA - RSA lib support Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | gpio: zynq: Add dummy gpio routinesJagannadha Sutradharudu Teki2014-01-10-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GPIO dummy routines are required for fdt build, may be removed these dependencies once the u-boot fdt is fully optimized. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | dts: zynq: Add basic fdt supportJagannadha Sutradharudu Teki2014-01-10-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch provides a basic fdt support for zynq u-boot. zynq-7000.dtsi-> initial arch dts file zynq-zed.dts -> initial zed board dts file more devices should be added in subsequent patches. u-boot build: once configuring of a board done for building dtb with zynq-zed.dts as an input zynq-uboot> make DEVICE_TREE=zynq-zed Enabled CONFIG_OF_SEPARATE for building dtb separately. There is a new binary called u-boot-dtb.bin which is a u-boot with devicetree supported. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | zynq-common: Define CONFIG_ENV_OVERWRITEJagannadha Sutradharudu Teki2014-01-10-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Defined CONFIG_ENV_OVERWRITE, which allow to overwrite serial baudrate and ethaddr. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | zynq-common: Define flash env. partitionJagannadha Sutradharudu Teki2014-01-10-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Last 128Kb sector of 1Mb flash is defined as u-boot environment partition. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| | * | | zynq-common: Change Env. Sector size to 128KbJagannadha Sutradharudu Teki2014-01-10-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changed Env. Sector size from 0x10000 to 128Kb Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
generated by cgit v1.1 at 2024-12-28 12:57:52 +0000