summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* DM9000: Make driver work properly for DM9000ARemy Bohmer2008-06-04-39/+54
| | | | | | | | | | | | | | | | | | | | | | The DM9000A network controller does not work with the U-boot DM9000x driver. Analysis showed that many incoming packets are lost. The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to check for a valid rx packet be done on the interrupt status register, not directly by performing the dummy read and the rx status check as is currently the case in the u-boot driver. When the recommended poll is done as suggested the driver starts working correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there can be more than 1 package in the fifo at the same time. The driver must perform the rx-status check in a loop and read and handle all packages until there is no more left _after_ the interrupt RX flag is set. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* DM9000: Improve eth_reset() routineRemy Bohmer2008-06-04-3/+31
| | | | | | | | | | | According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the reset procedure must be done twice to properly reset the DM9000 by means of software. This errata is not needed anymore for the DM9000A, but it does not bother it. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* DM9000: improve eth_send() routineRemy Bohmer2008-06-04-4/+11
| | | | | | | | | | | | The eth_send routine of the U-boot DM9000x driver does not match the DM9000 or DM9000A application notes/programming guides. This change improves the stability of the DM9000A network controller. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* DM9000: repair debug loggingRemy Bohmer2008-06-04-12/+21
| | | | | | | | | | It seems that the debugging code of the DM9000x driver in U-boot has not been compiled for a long time, because it cannot compile... Also rearranged some loglines to get more useful info while debugging. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* DM9000: Add data bus-width auto detection.Remy Bohmer2008-06-04-66/+129
| | | | | | | | | | | | | | | | | The U-boot DM9000x driver contains a compile time bus-width definition for the databus connected to the network controller. This compile check makes the code unclear, inflexible and is unneccessary. It can be asked to the network controller what its bus-width is by reading bits 6 and 7 of the interrupt status register. The linux kernel already uses a runtime mechanism to determine this bus-width, so the implementation below looks somewhat like that implementation. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Merge branch 'master' of git://www.denx.de/git/u-bootBen Warren2008-06-02-56/+78
|\
| * Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2008-05-27-48/+47
| |\ | | | | | | | | | | | | | | | | | | | | | Conflicts: include/configs/socrates.h Signed-off-by: Wolfgang Denk <wd@denx.de>
| | * USB: replace old swap_ with proper endianess conversion macrosChristian Eggers2008-05-22-45/+38
| | | | | | | | | | | | | | | Signed-off-by: Christian Eggers <ceggers@gmx.de> Signed-off-by: Markus Klotzbuecher <mk@denx.de>
| | * Fix endianess conversion in usb_ohci.cChristian Eggers2008-05-22-3/+3
| | | | | | | | | | | | | | | Signed-off-by: Christian Eggers <ceggers@gmx.de> Signed-off-by: Markus Klotzbuecher <mk@denx.de>
| | * USB: add support for multiple PCI OHCI controllersSergei Poselenov2008-05-22-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add new configuration variable CONFIG_PCI_OHCI_DEVNO. In case of several PCI USB controllers on a board this variable specifys which controller to use. Also add USB support for sokrates board. See doc/README.generic_usb_ohci for details. Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Markus Klotzbuecher <mk@denx.de>
| * | Socrates: Added USB support.Sergei Poselenov2008-05-27-9/+12
| | | | | | | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
| * | USB: add new configuration variable CONFIG_PCI_OHCI_DEVNOSergei Poselenov2008-05-27-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | In case of several PCI USB controllers on a board this variable specifys which controller to use. See doc/README.generic_usb_ohci for details. Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
| * | Socrates: add support for DS75 Digital Thermo Sensor on I2C bus.Sergei Poselenov2008-05-27-1/+11
| | | | | | | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
| * | Socrates: Config file cleanup.Sergei Poselenov2008-05-27-3/+4
| |/ | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
* | E1000: Add support for the 82541GI LF Intel Pro 1000 GT Desktop AdapterWolfgang Grandegger2008-06-02-2/+6
| | | | | | | | | | Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | ColdFire: Add 10 base ethernet support for mcf5445xTsiChung Liew2008-06-02-0/+6
| | | | | | | | | | Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | Add Marvell 88E1118 support for TSECRon Madrid2008-05-23-0/+31
| | | | | | | | | | Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | smc911x: add 16 bit supportJens Gehrlein2008-05-22-2/+34
|/ | | | | Signed-off-by: Jens Gehrlein <sew_s@tqs.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Merge branch 'master' of git://git.denx.de/u-boot-testingWolfgang Denk2008-05-21-9/+9
|\
| * Fix some whitespace issuesWolfgang Denk2008-05-21-9/+9
| | | | | | | | | | | | introduced by 53677ef18 "Big white-space cleanup." Signed-off-by: Wolfgang Denk <wd@denx.de>
* | Merge branch 'socrates' of /home/wd/git/u-boot/projectsWolfgang Denk2008-05-21-9/+1160
|\ \
| * | socrates: fix second TSEC configuration (it is actually TSEC3)Sergei Poselenov2008-05-20-6/+6
| | | | | | | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
| * | Fixed reset for socratesSergei Poselenov2008-05-20-9/+14
| | | | | | | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
| * | socrates: changes to support FDTSergei Poselenov2008-05-20-33/+50
| | | | | | | | | | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
| * | Initial support for "Socrates" boardSergei Poselenov2008-05-20-0/+1129
| | | | | | | | | | | | Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
* | | Merge branch 'lwmon5' of /home/wd/git/u-boot/projectsWolfgang Denk2008-05-21-8/+155
|\ \ \
| * | | POST: replace the LOGBUFF_INITIALIZED flag in gd->post_log_word (1 << 31) ↵Yuri Tikhonov2008-05-20-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | with the GD_FLG_LOGINIT flag in gd->flags. This way we become able to utilize the full post_log_word for POST activities (overwise, POST ECC, which has 0x8000 ID, could be erroneously treated as started in post_output_backlog() even if there was actually no POST ECC run (because of OCM POST failure, for example). Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
| * | | POST: mark OCM test as POST_STOPYuri Tikhonov2008-05-20-1/+1
| | | | | | | | | | | | | | | | Signed-off-by: Ilya Yanok <yanok@emcraft.com>
| * | | POST: add POST_STOP flagYuri Tikhonov2008-05-20-2/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Don't run futher tests in case of a test fails that is marked as POST_STOP. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
| * | | POST: switch CFG_POST_OCM with CFG_POST_CODEC (workaround)Yuri Tikhonov2008-05-20-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch the OCM testid with the codec one. The reason is that current implementation requires the POST_ROM testid to fit into lower 16 bits, and the codec test will never run with POST_ROM hopefully. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
| * | | lwmon5: enable OCM post test on lwmon5 boardYuri Tikhonov2008-05-20-0/+6
| | | | | | | | | | | | | | | | Signed-off-by: Ilya Yanok <yanok@emcraft.com>
| * | | POST: OCM test added.Yuri Tikhonov2008-05-20-0/+104
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Added OCM test to POST layer. This version runs before all other tests but doesn't yet interrupt post sequence on failure. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
| * | | POST: typo fixYuri Tikhonov2008-05-20-1/+1
| |/ / | | | | | | | | | Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* | | Make ads5121 out-of-tree compiling safeYork Sun2008-05-21-1/+6
| | | | | | | | | | | | | | | | | | Reuse the existing DIU driver in board/freescale/common. Signed-off-by: York Sun <yorksun@freescale.com>
* | | Adding DIU support for Freescale 5121ADSYork Sun2008-05-21-21/+261
| | | | | | | | | | | | | | | | | | | | | | | | Add DIU and cfb console support to FSL 5121ADS board. Use #define CONFIG_VIDEO in config file to enable fb console. Signed-off-by: York Sun <yorksun@freescale.com>
* | | Replace DPRINTF with debugYork Sun2008-05-21-35/+29
| | | | | | | | | | | | | | | | | | Remove DPRINTF macro and replace it with generic debug macro. Signed-off-by: York Sun <yorksun@freescale.com>
* | | Move pixel clock setting to board fileYork Sun2008-05-21-34/+25
| |/ |/| | | | | | | | | | | The clock divider has different format in 5121 and 8610. This patch moves it to board specific code. Signed-off-by: York Sun <yorksun@freescale.com>
* | Big white-space cleanup.Wolfgang Denk2008-05-21-13519/+13530
|/ | | | | | | | | | | This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <wd@denx.de>
* common/usb.c: fix incorrect escape sequenceHebbar2008-05-20-1/+1
| | | | Signed off by: Gururaja Hebbar <gururajakr@sanyo.co.in>
* Fix 8313ERDB board configurationYork Sun2008-05-19-8/+6
| | | | | | | | | Change LCRR clock ratio from 2 to 4 to commodate VSC7385. Correct TSEC1 vs TSEC2 assignment. Define ETHADDR and ETH1ADDR always. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com>
* Release v1.3.3Wolfgang Denk2008-05-19-1/+299
| | | | | | Update CHANGELOG for release. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk2008-05-19-1/+30
|\
| * ppc4xx: Canyonlands: Disable PCIe0/SATA in dev-tree depending on selectionStefan Roese2008-05-19-1/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When SATA is selected (via jumper J6) we need to disable the first PCIe node in the device tree, so that Linux doesn't initialize it. Otherwise the Linux SATA driver will fail to detect the devices. The same goes the other way around too. So if PCIe is selected we need to disable the SATA node in the device tree. This is because PCIe port 0 and SATA on 460EX share the same pins (multiplexed) and we have to configure in U-Boot which peripheral is enabled. Signed-off-by: Stefan Roese <sr@denx.de>
* | i386: Fix multiple definitions of __show_boot_progressJean-Christophe PLAGNIOL-VILLARD2008-05-19-14/+14
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | sc530_spunk: add missing SOBJS entryJean-Christophe PLAGNIOL-VILLARD2008-05-19-1/+1
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | sc520_spunk: Fix flashJean-Christophe PLAGNIOL-VILLARD2008-05-19-24/+6
| | | | | | | | | | | | | | flash.c:593: warning: dereferencing type-punned pointer will break strict-aliasing rules flash.c:398: error: label at end of compound statement Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | drivers/pcmcia: add missing i82365Jean-Christophe PLAGNIOL-VILLARD2008-05-19-4/+1
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | i386/bootm: remove unused varJean-Christophe PLAGNIOL-VILLARD2008-05-19-1/+0
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | example/gitignore: update with all generated examplesJean-Christophe PLAGNIOL-VILLARD2008-05-19-0/+4
|/ | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* TQM8272: fix out-of-tree buildingWolfgang Denk2008-05-15-8/+16
| | | | | | ...and add to MAKEALL script Signed-off-by: Wolfgang Denk <wd@denx.de>
generated by cgit v1.1 at 2024-12-01 18:44:42 +0000