summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* powerpc/mpc8xxx DDR: Fall back to raw timing for first controller onlyYork Sun2012-08-23-1/+1
| | | | | | | | Only the first DIMM of first controller should fall back to raw timing parameters if SPD is missing or corrupted. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx DDR: Fix CAS latency calculationYork Sun2012-08-23-2/+4
| | | | | | | Empty slot should be skipped when calculating CAS latency. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Fix bug for extended DDR timingYork Sun2012-08-23-20/+43
| | | | | | | | Faster DDR3 timing requires parameters exceeding previously defined range. Extended parameters are fixed. Added some debug messages. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Enable 3-way and 4-way DDR interleavingYork Sun2012-08-23-320/+489
| | | | | | | | Restructure DDR interleaving option to support 3 and 4 DDR controllers for 2-, 3- and 4-way interleaving. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Add support for cas latency 12 and aboveYork Sun2012-08-23-7/+21
| | | | | | | | Required by JEDEC 79-3E for high speed DDR3. Also change "CSn disabled" message to debug. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Add fine timing support for DDR3York Sun2012-08-23-13/+42
| | | | | | | | When the DDR3 speed goes higher, we need to utilize fine offset from SPD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Skip zero values for DDR debug registersYork Sun2012-08-23-3/+11
| | | | | | | | | | | Some debug registers have non-zero default out of reset. If software is not setting debug registers, skip writing to them to avoid unnecessary overriding. Also add debug messages for workarounds and debug registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: fix core id for multicore bootingYork Sun2012-08-23-6/+53
| | | | | | | | | | For the cores with multiple threads, we need to figure out which physical core a thread belongs. To match the core ids, update PIR registers and spin tables. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Added new ext fields to IFCKumar Gala2012-08-23-6/+24
| | | | | | | | | | In case more than 32 bit address is used, the EXT bit should be set. Need to fix up address map for IFC #CS for 4, also need to move # of IFC banks into config_mpc85xx.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Add IFC offset for DPAA/Corenet platformsKumar Gala2012-08-23-0/+1
| | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Add e6500 processor detectionKumar Gala2012-08-23-0/+4
| | | | | Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: use topology registers to calculate number of coresYork Sun2012-08-23-9/+70
| | | | | | | | | We have actual topology infomation to find out exactly which core is present. Calculate the number of cores if not specified. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Add immap for topology and rcpm registersYork Sun2012-08-23-1/+87
| | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add IFC LAW target ID for FSL High-End SoCPrabhakar Kushwaha2012-08-23-0/+1
| | | | | | | | | | Freescale's High-End SoC are going to have Integrated Flash controller (IFC)'s support. So add IFC LAW target ID support for High-End SoC or corenet SoC. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx:Enable debugger support to missed e500v2 SoCPrabhakar Kushwaha2012-08-23-0/+4
| | | | | | | | | | | | | | | Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some restrictions on external debugging (JTAG). Need to define define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be used during boot to work around the limitations. Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for debug support. Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/fsl-corenet: work around erratum A004510Scott Wood2012-08-23-0/+355
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum A004510 says that under certain load conditions, modified cache lines can be discarded, causing data corruption. To work around this, several CCSR and DCSR register updates need to be made in a careful manner, so that there is no other transaction in corenet when the update is made. The update is made from a locked cacheline, with a delay before to flush any previous activity, and a delay after to flush the CCSR/DCSR update. We can't use a readback because that would be another corenet transaction, which is not allowed. We lock the subsequent cacheline to prevent it from being fetched while we're executing the previous cacheline. It is filled with nops so that a branch doesn't cause us to fetch another cacheline. Ordinarily we are running in a cache-inhibited mapping at this point, so we temporarily change that. We make it guarded so that we should never see a speculative load, and we never do an explicit load. Thus, only the I-cache should ever fill from this mapping, and we flush/unlock it afterward. Thus we should avoid problems from any potential cache aliasing between inhibited and non-inhibited mappings. NOTE that if PAMU is used with this patch, it will need to use a dedicated LAW as described in the erratum. This is the responsibility of the OS that sets up PAMU. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/fsl-corenet: remove dead variant symbolsScott Wood2012-08-23-72/+7
| | | | | | | | | | | These are not supported as individual build targets, but instead are supported by another target. The dead p4040 defines in particular had bitrotted significantly. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: remove support for the Freescale P3060Timur Tabi2012-08-23-1971/+3
| | | | | | | | The P3060 was cancelled before it went into production, so there's no point in supporting it. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: get rid of enum board_slots in P4080 MDIO driverTimur Tabi2012-08-23-40/+19
| | | | | | | | | enum board_slots contained six values, where SLOT1 == 1, SLOT2 == 2, and so on. This is pointless, so remove it. Also move the lane_to_slot[] array to the top of the file so that it can be used by other functions. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* fm-eth: use fdt_status_disabled() function in ft_fixup_port()Timur Tabi2012-08-23-6/+5
| | | | | | | | We have a dedicated function for setting the node status now, so use it. Also improve a comment and fix the type of the phandle variable. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: introduce function serdes_device_from_fm_port()Timur Tabi2012-08-23-0/+33
| | | | | | | | | In order to figure out which SerDes lane a given Fman port is connected to, we need a function that maps the fm_port namespace to the srds_prtcl namespace. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* fm-eth: add function fm_info_get_phy_address()Timur Tabi2012-08-23-0/+17
| | | | | | | | | Function fm_info_get_phy_address() returns the PHY address for a given Fman port. This is handy when the MDIO code needs to fixup the Ethernet nodes in the device tree to point to PHY nodes for a specific PHY address. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: add support for FM2 DTSEC5Timur Tabi2012-08-23-0/+12
| | | | | | | | Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second Fman, so add the Fman and SerDes macros for that DTSEC. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mpc85xx: use LCRR_DBYP define instead of raw constantPaul Gortmaker2012-08-23-12/+12
| | | | | | | | | | | | | | | Using the raw value of 0x80000000 directly in the code can lead to "count the zeros" bugs like that fixed in commit 718e9d13b98 ("MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC") Change all existing raw values to use the symbolic value of LCRR_DBYP instead. Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* nand_spl: change out_be32 to raw_writel and depend on subsequent syncMatthew McClintock2012-08-23-73/+71
| | | | | | | | | | | | | This change reduces the SPL size by removing the redundant syncs produced by out_be32 and just replies on one final sync Done with: sed -r '/in_be32/b; s/(out_be32)\(([^,]*),\s+(.*)\)/__raw_writel(\3, \2)/g' -i `git grep --name-only sdram_init nand_spl/` Signed-off-by: Matthew McClintock <msm@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* nand_spl: p1023rds: wait before enabling DDR controllerMatthew McClintock2012-08-23-5/+20
| | | | | | | | We have a requirement to wait a period of time before enabling the DDR controller Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* nand_spl: update udelay for Freescale boardsMatthew McClintock2012-08-23-15/+60
| | | | | | | | | | | | | | Let's use the more appropriate udelay for the nand_spl. While we can't make use of u-boot's full udelay we can atl east use a for loop that won't get optimized away .Since we have the bus clock we can use the timebase to calculate wall time. Looked at reusing the u-boot udelay functions but it pulls in a lot of code and would require quite a bit of work to keep us within the very small space constrains we currently have Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p1010rdb: nandboot: compare SVR properlyMatthew McClintock2012-08-23-1/+2
| | | | | | | | | | | | | | | | We were not comparing the SVRs properly previously. This comparison will properly shift the SVR and mask off the E bit This fixes the boot output to show the correct DDR bus width: 512 MiB (DDR3, 16-bit, CL=5, ECC off) instead of 512 MiB (DDR3, 32-bit, CL=5, ECC off) Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* p1010rdb: fix ddr values for p1014rdb (setting bus width to 16bit)Matthew McClintock2012-08-23-3/+4
| | | | | | | | | | | There was an extra 0 in front of the value we were using to mask, remove it to improve the code. Also fix the value written to ddr_sdram_cfg to set the bus width properly to 16 bits Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* p1014rdb: set ddr bus width properly depending on SVRMatthew McClintock2012-08-23-0/+12
| | | | | | | | | | Currently, for NAND boot for the P1010/4RDB we hard code the DDR configuration. We can still dynamically set the DDR bus width in the nand spl so the P1010/4RDB boards can boot from the same u-boot image Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Remove P1015 and P1016 from CPU listYork Sun2012-08-23-49/+7
| | | | | | | | P1015 is the same as P1011 and P1016 is the same as P1012 from software point of view. They have different packages but share SVRs. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/CoreNet: add tool to support pbl image build.Shaohui Xie2012-08-23-0/+601
| | | | | | | | | | Provides a tool to build boot Image for PBL(Pre boot loader) which is used on Freescale CoreNet SoCs, PBL can be used to load some instructions and/or data for pre-initialization. The default output image is u-boot.pbl, for more details please refer to doc/README.pblimage. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Slave module for boot from PCIELiu Gang2012-08-23-49/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When boot from PCIE, slave's core should be in holdoff after powered on for some specific requirements. Master will release the slave's core at the right time by PCIE interface. Slave's ucode and ENV can be stored in master's memory space, then slave can fetch them through PCIE interface. For the corenet platform, ucode is for Fman. NOTE: Because the slave can not erase, write master's NOR flash by PCIE interface, so it can not modify the ENV parameters stored in master's NOR flash using "saveenv" or other commands. environment and requirement: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image is in master NOR flash. 3. Put the slave's ucode and ENV into it's own memory space. 4. Normally boot from local NOR flash. 5. Configure PCIE system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to one PCIE interface by RCW. 3. RCW should configure the SerDes, PCIE interfaces correctly. 4. Must set all the cores in holdoff by RCW. 5. Must be powered on before master's boot. For the slave module, need to finish these processes: 1. Set the boot location to one PCIE interface by RCW. 2. Set a specific TLB entry for the boot process. 3. Set a LAW entry with the TargetID of one PCIE for the boot. 4. Set a specific TLB entry in order to fetch ucode and ENV from master. 5. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 6. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. In addition, the processes are very similar between boot from SRIO and boot from PCIE. Some configurations like the address spaces can be set to the same. So the module of boot from PCIE was added based on the existing module of boot from SRIO, and the following changes were needed: 1. Updated the README.srio-boot-corenet to add descriptions about boot from PCIE, and change the name to README.srio-pcie-boot-corenet. 2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to "xxxx_SRIO_PCIE_BOOT", and the image builded with "xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and from PCIE. 3. Updated other macros and documents if needed to add information about boot from PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Master module for boot from PCIELiu Gang2012-08-23-40/+156
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For the powerpc processors with PCIE interface, boot location can be configured from one PCIE interface by RCW. The processor booting from PCIE can do without flash for u-boot image. The image can be fetched from another processor's memory space by PCIE link connected between them. The processor booting from PCIE is slave, the processor booting from normal flash memory space is master, and it can help slave to boot from master's memory space. When boot from PCIE, slave's core should be in holdoff after powered on for some specific requirements. Master will release the slave's core at the right time by PCIE interface. Environment and requirement: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image is in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure PCIE system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to one PCIE interface by RCW. 3. RCW should configure the SerDes, PCIE interfaces correctly. 4. Must set all the cores in holdoff by RCW. 5. Must be powered on before master's boot. For the master module, need to finish these processes: 1. Initialize the PCIE port and address space. 2. Set inbound PCIE windows covered slave's u-boot image stored in master's NOR flash. 3. Set outbound windows in order to configure slave's registers for the core's releasing. 4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2" or "PCIE3" using the following command: setenv bootmaster PCIE1 saveenv Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Update README and README.srio-pcie-boot-corenetLiu Gang2012-08-23-105/+118
| | | | | | | | | Added descriptions about boot from PCIE in the files README and doc/README.srio-pcie-boot-corenet, and changed the name of the doc/README.srio-boot-corenet to doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Get rid of the CONFIG_SRIOBOOT_SLAVE_PORTx macroLiu Gang2012-08-23-19/+28
| | | | | | | | | | | | | | | | When compile the slave image for boot from SRIO, no longer need to specify which SRIO port it will boot from. The code will get this information from RCW and then finishes corresponding configurations. This has the following advantages: 1. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just rewrite the new RCW with selected port, then the code will get the port information by reading new RCW. 2. It will be easier to support other boot location options, for example, boot from PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build targetLiu Gang2012-08-23-128/+129
| | | | | | | | | | | | | | | | | | | | | | Get rid of the SRIOBOOT_MASTER build target, and to support for serving as a SRIO boot master via environment variable. Set the environment variable "bootmaster" to "SRIO1" or "SRIO2" using the following command: setenv bootmaster SRIO1 saveenv The "bootmaster" will enable the function of the SRIO boot master, and this has the following advantages compared with SRIOBOOT_MASTER build configuration: 1. Reduce a build configuration item in boards.cfg file. No longer need to build a special image for master, just use a normal target image and set the "bootmaster" variable. 2. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just set the corresponding value to "bootmaster" based on the using SRIO port. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Update README.srio-boot-corenetLiu Gang2012-08-23-37/+33
| | | | | | | | | | | | | | | Update some descriptions due to the implementation changes: For master: Get rid of the SRIOBOOT_MASTER build target, and to support for serving as a SRIO boot master via environment variable. For slave: 1. When compile the slave image for boot from SRIO, no longer need to specify which SRIO port it will boot from. 2. All slave's cores should be in hold off. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditionalYork Sun2012-08-23-3/+56
| | | | | | | | | | | | | | | | | This erratum applies to the following SoCs: P4080 rev 1.0, 2.0, fixed in rev 3.0 P2041 rev 1.0, 1.1, fixed in rev 2.0 P3041 rev 1.0, 1.1, fixed in rev 2.0. Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround may degrade performance. P4080 erratum CPU22 shares the same workaround. So it is always enabled for P4080. For other SoCs, it can be disabled by hwconfig with syntax: fsl_cpu_a011:disable Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* nand/fsl_elbc: shrink SPL a bit by converting out_be32() to __raw_writel()Scott Wood2012-08-22-22/+25
| | | | | | | | | This is needed to make room for a bugfix on p1_p2_rdb_pc. A sync is used before the final write to LSOR that initiates the transaction, to ensure all the other set up has been completed. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: Stack Pointer not properly alignedJoakim Tjernlund2012-08-22-3/+2
| | | | | | | | | The code first aligns the SP to 16 then subtract 8, making it 8 bytes aligned. Furthermore the initial stack frame not quite correct either. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mpc85xx: Initial SP alignment is wrong.Joakim Tjernlund2012-08-22-11/+5
| | | | | | | | | | | | PowerPC mandates SP to be 16 bytes aligned. Furthermore, a stack frame is added, pointing to the reset vector which may in the way when gdb is walking the stack because the reset vector may not accessible depending on emulator settings. Also use a temp register so gdb doesn't pick up intermediate values. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Makefile: fix HAVE_VENDOR_COMMON_LIBScott Wood2012-08-17-2/+2
| | | | | | | | | | | Commit 8b5a02640adf77301f943e8754992c50df004e8a ("Makefile: cosmetic: optimize usage of LIBS-y") broke the build of boards that have a board vendor "common" directory, by introducing a space between "LIBS-" and "y". Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* mtd/cfi_flash: fix write problems for Numonyx P33/30 32 MBit flashsHolger Brunck2012-08-13-22/+44
| | | | | | | | | | | | | | | | | | commit 54652991 Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads to problems for smaller versions of this chip e.g. the 32Mbit version with deviceid 0x16 on mgcoge. So move the code for this work around to an own function and check previously manufacturer id and device id to not break other flashes which don't need this work around. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Stefan Roese <sr@denx.de> cc: Philippe De Muyter <phdm@macqel.be> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Stefan Roese <sr@denx.de>
* cfi_flash: add support for Spansion flash PPB sector protectionAnatolij Gustschin2012-08-13-0/+59
| | | | | | | | | | Erasing flash sectors protected with persistent protection bit (PPB) mechanism on Spansion flash chips doesn't work. Add sector protection status checking and sector lock and unlock commands to fix this. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* dts/Makefile: Turn off some predefined macrosHorst Kronstorfer2012-08-10-1/+2
| | | | | | | | | | | Add '-ansi' to DTS_CPPFLAGS to avoid unwanted expansion of dts content that matches some predefined macros. Example: A number of PowerPC related *.dts files in the kernel define a property named 'linux,network-index' which (w/o '-ansi') is expanded to '1,network-index' by the preprocessor because of '#define linux 1.' Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
* Add support for DS1388.Kenth Eriksson2012-08-10-0/+27
| | | | | | | | | | Support for DS1388 is added by extending the DS1337 driver. DS1388 is similar to DS1337. The time registers are offset by 1 (due to support for hundreds of seconds), and there is no century bit. The configuration and trickle charge registers are also different. Tested on hardware with Freescale P2010 and DS1388. Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
* dts/Makefile: Check for empty $(LDSCRIPT)Horst Kronstorfer2012-08-10-2/+3
| | | | | | | | Make sure that $(LDSCRIPT) is not empty before calling process_lds with 'cat $(LDSCRIPT)' else cat will block waiting for input from stdin. Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
* Makefile: cosmetic: optimize usage of LIBS-yDaniel Schwierzeck2012-08-10-13/+7
| | | | Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* Makefile: replace LIBS by LIBS-yDaniel Schwierzeck2012-08-10-68/+68
| | | | | | | Synchronize with ALL-y handling and code in spl/Makefile. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit v1.1 at 2024-12-30 04:04:38 +0000