summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* tegra2: Fix conflicting pinmux for UARTAStephen Warren2012-02-12-0/+12
| | | | | | | | | | | | | | | Tegra appears to boot with function UARTA pre-selected on mux group SDB. If two mux groups are both set to the same function, it's unclear which group's pins drive the RX signals into the HW module. For UARTA, SDB certainly overrides group IRTX in practice. To solve this, configure some alternative function on SDB to avoid the conflict. Also, tri-state the group to avoid driving any signal onto it until we know what's connected. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* fw_env.h: fix commentFrans Meulenbroeks2012-02-11-2/+2
| | | | | | | made description according to implementation (where the config file is the default). Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
* Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2012-02-11-0/+23
|\ | | | | | | | | | | * 'master' of /home/wd/git/u-boot/custodians: add STM29F400BB to table of supported legacy flashs * Fix: watchdog timed out, if flash blank (0xFF) blocks
| * Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk2012-02-11-0/+23
| |\ | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-cfi-flash: add STM29F400BB to table of supported legacy flashs * Fix: watchdog timed out, if flash blank (0xFF) blocks
| | * add STM29F400BB to table of supported legacy flashsDavid Müller (ELSOFT AG)2012-02-09-0/+20
| | | | | | | | | | | | | | | Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
| | * * Fix: watchdog timed out, if flash blank (0xFF) blocksJens Scharsig (BuS Elektronik)2012-02-09-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current implementation of cfi_flash uses udelay to reset watchdog. If several blocks are blank (0xff filled) the watchdog timed out. The reason is, udelay is never called, if flash device is ready to fast. e.g. mw.w $(copy_addr) FFFF 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog timed out mw.w $(copy_addr) 0000 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog not timed out This patch adds an extra watchdog reset in front of flash ready check. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2012-02-11-693/+3085
|\ \ \ | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of /home/wd/git/u-boot/custodians: nand/fsl_elbc: Convert to self-init nand: Introduce CONFIG_SYS_NAND_SELF_INIT nand_spl: store ecc data on the stack mtd/nand: Add ONFI support for FSL NAND controller nand: make 1-bit software ECC configurable nand: Sanitize ONFI strings. nand: Merge changes to BBT from Linux nand driver nand: Merge changes from Linux nand driver nand: cleanup whitespace nand: Add more NAND types from Linux nand driver nand: Merge BCH code from Linux nand driver NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS NAND: remove NAND_MAX_CHIPS definitions nand_spl_simple: store ecc data on the stack
| * | Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk2012-02-11-693/+3085
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-nand-flash: nand/fsl_elbc: Convert to self-init nand: Introduce CONFIG_SYS_NAND_SELF_INIT nand_spl: store ecc data on the stack mtd/nand: Add ONFI support for FSL NAND controller nand: make 1-bit software ECC configurable nand: Sanitize ONFI strings. nand: Merge changes to BBT from Linux nand driver nand: Merge changes from Linux nand driver nand: cleanup whitespace nand: Add more NAND types from Linux nand driver nand: Merge BCH code from Linux nand driver NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS NAND: remove NAND_MAX_CHIPS definitions nand_spl_simple: store ecc data on the stack
| | * | nand/fsl_elbc: Convert to self-initScott Wood2012-01-26-5/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver doesn't yet make use of the added flexibility (not that that should stop anyone from converting...), but it will with the in-progress hack to support 4k-page NAND. Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: Introduce CONFIG_SYS_NAND_SELF_INITScott Wood2012-01-26-37/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows a driver to run code between nand_scan_ident() and nand_scan_tail(), among other things. See the additions to doc/README.nand for details. To allow a gradual transition, Boards that don't set CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but new drivers should not require this, and existing drivers should be converted when convenient. Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand_spl: store ecc data on the stackScott Wood2012-01-26-54/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adapt the following patch from spl to nand_spl: Author: Stefano Babic <sbabic@denx.de> Date: Thu Dec 15 10:55:37 2011 +0100 nand_spl_simple: store ecc data on the stack Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM which is likely to contain already loaded data. The patch saves the oob data and the ecc on the stack replacing the fixed address in RAM. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com> While nand_spl is on its way out, in favor of spl, there are still many boards using it, and conversions are gradual. This allows us to get rid of CONFIG_SYS_NAND_ECCSTEPS and CONFIG_SYS_NAND_ECCTOTAL now, which would otherwise be likely to linger unreferenced after a conversion. It also eliminates a temporary error in the hawkboard_nand build, since the spl version of the patch removed ECCSTEPS/TOTAL from hawkboard.h, but the spl conversion is pending (and may be merged via a different tree). Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | mtd/nand: Add ONFI support for FSL NAND controllerShengzhou Liu2012-01-26-7/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - fix NAND_CMD_READID command for ONFI detect. - add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: make 1-bit software ECC configurableChristian Hitz2012-01-26-1/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The software ECC algorithm is not necessary when hardware ECC is available and can be left out for a smaller image size. Enable with CONFIG_MTD_ECC_SOFT. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: Sanitize ONFI strings.Christian Hitz2012-01-26-1/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This is part of the synchronization with the nand driver to the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: Merge changes to BBT from Linux nand driverChristian Hitz2012-01-26-99/+330
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: Merge changes from Linux nand driverChristian Hitz2012-01-26-315/+541
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> [scottwood@freescale.com: minor fixes] Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: cleanup whitespaceChristian Hitz2012-01-26-74/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bring up to date with corresponding file from linux. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: Add more NAND types from Linux nand driverChristian Hitz2012-01-26-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch merges the additional NAND flash types from the 3.0 Linux kernel. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand: Merge BCH code from Linux nand driverChristian Hitz2012-01-26-8/+1788
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch merges the BCH ECC algorithm from the 3.0 Linux kernel. This enables U-Boot to support modern NAND flash chips that require more than 1-bit of ECC in software. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPSScott Wood2012-01-26-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | NAND_MAX_CHIPS has been replaced by CONFIG_SYS_NAND_MAX_CHIPS, and the latter defaults to 1. Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | NAND: remove NAND_MAX_CHIPS definitionsVladimir Zapolskiy2012-01-26-31/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This change follows the change by Wolfgang Grandegger (commit 6c869637fef), which allows to remove useless NAND_MAX_CHIPS definitions in board config files. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| | * | nand_spl_simple: store ecc data on the stackStefano Babic2012-01-26-55/+17
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM which is likely to contain already loaded data. The patch saves the oob data and the ecc on the stack replacing the fixed address in RAM. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2012-02-11-175/+421
|\ \ \ | |/ / | | | | | | | | | | | | | | | * 'master' of /home/wd/git/u-boot/custodians: ARM: AM33XX: Add i2c support ARM: AM33XX: Add AM33XX I2C driver support ARM: I2C: I2C Multi byte address support
| * | ARM: AM33XX: Add i2c supportPatil, Rachna2012-01-23-1/+118
| | | | | | | | | | | | | | | | | | | | | Add i2c driver board hookup for AM335X EVM Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
| * | ARM: AM33XX: Add AM33XX I2C driver supportPatil, Rachna2012-01-23-7/+13
| | | | | | | | | | | | | | | | | | | | | | | | 1. Compliant with Philips I2C specification version 2.1 2. Supports upto 100Kbps in standard mode Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
| * | ARM: I2C: I2C Multi byte address supportPatil, Rachna2012-01-23-173/+296
| |/ | | | | | | | | | | | | | | | | | | Existing OMAP I2C driver does not support address length greater than one. Hence this patch is to add support for 2 byte address read/write. Signed-off-by: Philip, Avinash <avinashphilip@ti.com> Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
* | README: update (C) entryWolfgang Denk2012-01-19-1/+1
|/ | | | | | | There are tools that automatically extract this information, so better make it up to date. Signed-off-by: Wolfgang Denk <wd@denx.de>
* overo: add SPL supportAndreas Müller2012-01-16-29/+147
| | | | | | | | | | * implementation based on ti beagleboard/omap3evm * timing data and i2c workaround for revision 0 boards taken from x-loader * run-tested with overo revision 0 and 1 / boot from NAND and SDcard * run-tested with x-loader Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
* omap_rev_string: output to stdoutAndreas Müller2012-01-16-17/+11
| | | | | | | | * avoid potential buffer overflows * allow SPL-build not to output "Texas Instruments Revision detection unimplemented" Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP SPL: call timer_init in s_init to make udelay work earlierAndreas Müller2012-01-16-2/+2
| | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* drivers/i2c/omap24xx_i2c.c: move all local variables to SRAMAndreas Müller2012-01-16-4/+9
| | | | | | | | | | | | | At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately this pin is also used for revision detection. Therefore we need to send shut-up to TWL4030 to avoid reading wrong revision. In SPL this must be done before SDRAM is set up because the type of SDRAM is revision dependent. By this patch it is ensured that all variables used by omap24xx_i2c.c are located in SRAM. Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* include/configs/omap3_overo.h: several cleanupsAndreas Müller2012-01-16-35/+31
| | | | | | | | | * remove unused macros * remove unused macro values * align tabs * remove Free Software Foundation address Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* board/overo/overo.c: replace printf with one argument by putsAndreas Müller2012-01-16-7/+7
| | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* drivers/i2c/omap24xx_i2c.c: replace printf with one argument by putsAndreas Müller2012-01-16-6/+6
| | | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de>
* ARM:AM33XX: Add SPL support for AM335X EVMChandan Nath2012-01-16-122/+231
| | | | | | | | | | | This patch is added to support SPL feature on AM335X platform. In this patch, MMC1 is configured as boot device for SPL and support for other devices will be added in the next patch series. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* ARM:AM33XX: Add mmc/sd supportChandan Nath2012-01-16-0/+205
| | | | | | | | | This patch add supports for mmc/sd driver on AM335X platform. PLL and pinmux configurations for mmc/sd are configured in this patch. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Fixing AM335X config parametersChandan Nath2012-01-16-8/+3
| | | | | | | | | This patch is added to correct some of the AM335X config parameters which were incorrect along with some cleanup like removing unused code. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Fix ddr and timer register offsetChandan Nath2012-01-16-27/+32
| | | | | | | | This patch is added to update incorrect ddr and timer register offset. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* ARM:AM33XX: Replace CONFIG_AM335X with CONFIG_AM33XXChandan Nath2012-01-16-3/+3
| | | | | | | | | This patch is added to replace CONFIG_AM335X symbol with CONFIG_AM333XX for AM33XX platforms. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Thomas Weber <weber@corscience.de>
* cm-t35: use the new EEPROM module to read the MAC addressNikita Kiryanov2012-01-16-3/+54
| | | | | | | | | Switch to the new EEPROM module and fix the problem of MAC address being read from the wrong offset due to lack of distinction between EEPROM layouts. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: pass correct revision information to LinuxNikita Kiryanov2012-01-16-0/+28
| | | | | | | Read revision from EEPROM and pass it to Linux. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* omap3: make get_board_rev() function weakNikita Kiryanov2012-01-16-1/+2
| | | | | | | | | | Current get_board_rev() function returns a hard coded value which is obviously incorrect for the majority of boards. Allow boards to provide a correct implementation by making this function weak. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: add EEPROM module and pass Linux a serial numberNikita Kiryanov2012-01-16-1/+95
| | | | | | | | Add board specific EEPROM handling module, read the serial number from the EEPROM and pass it to Linux. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: various cleanupsNikita Kiryanov2012-01-16-6/+4
| | | | | | | | | Move #ifdef CONFIG_SMC911X out of board_eth_init() function, simplify the board_mmc_init() function, and enclose handle_mac_address() in the CONFIG_SMC911X. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t35: cleanup the config fileNikita Kiryanov2012-01-16-39/+39
| | | | | | | | Remove values from boolean defines, fix indentation, etc.. No functional changes. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* omap4: fix boot issue on ES2.0 PandaAneesh V2012-01-16-3/+3
| | | | | | | | | | | | | Fix boot issue on ES2.0 Panda by tuning some IO settings. The CONTROL_EFUSE_2 register has to be over-ridden in software for 4430 boards. Commit 23e9f0723e48615332119de4f4ec7a833a282628 wrongly did this for CONTROL_EFUSE_1. Reverting this and doing it for CONTROL_EFUSE_2. Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Raúl Porcel <armin76@gentoo.org>
* beagle: add eeprom expansion board info for bct brettl3Peter Meerwald2012-01-16-0/+4
| | | | | | | this is for a prototyping board vendor/product ids have been added to http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs
* ARMV7: Add support For Logic OMAP35x/DM37x modulesPeter Barada2012-01-16-0/+703
| | | | | | | | | | | | This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo reference boards. It assumes U-boot is loaded to SDRAM with the help of another small bootloader (x-load) running from SRAM. Signed-off-by: Peter Barada <peter.barada@logicpd.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* arm, davinci: Change byte order of RTC kick register valuesChristian Riesch2012-01-16-4/+4
| | | | | | | | Now the values in the defines agree with those in the manuals. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de>
* OMAP3: Remove unused define CONFIG_OMAP3_*_DDRThomas Weber2012-01-16-30/+0
| | | | | | | | | | | This patch removes the unused definitions: CONFIG_OMAP3_MICRON_DDR CONFIG_OMAP3_NUMONYX_DDR CONFIG_OMAP3_INFINEON_DDR Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
generated by cgit v1.1 at 2024-12-28 14:06:29 +0000