summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* MMC: DWMMC: Fix FIFO_DEPTH calculationRajeshwari Shinde2013-06-17-8/+6
| | | | | | | | | | | | | | | | | | | | Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time for mmc rescan command. In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1). Instead of storing the correct value, we were recalculating the FIFO_DEPT each time which is not correct. Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues" http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247 Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* power: exynos-tmu: use the mux_addr bit fields in tmu_control registerNaveen Krishna Chatradhi2013-06-13-1/+10
| | | | | | | | | This patch implements the mux_addr bit fields defined in tmu_control register (used for debugging purpose) Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Reviewed-by: Vadim Bendebury <vbendeb@google.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* power: exynos-tmu: fix warnings and clean up codeNaveen Krishna Chatradhi2013-06-13-80/+90
| | | | | | | | | | | | | | | This patch does the folowing 1. change the data types for unsigned int variable to unsigned 2. change the tmu_base type to struct exynos5_tmu_reg * 3. Add timer functionality for get_cur_temp() 4. error handling in the get_tmu_fdt_values() 5. Add check for curr_temp reading 6. some cosmotic changes. Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Reviewed-by: Vadim Bendebury <vbendeb@google.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* COMMON: MMC: Command to support EMMC booting and to resize EMMC boot partitionAmar2013-06-13-2/+107
| | | | | | | This patch adds commands to access(open/close) and resize boot partitions on EMMC. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDK5250: Enable EMMC bootingAmar2013-06-13-13/+74
| | | | | | | This patch adds support for EMMC booting on SMDK5250. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* MMC: APIs to support resize of EMMC boot partitionAmar2013-06-13-0/+160
| | | | | | | This patch adds APIs to access(open / close) and to resize boot partiton of EMMC. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDTAmar2013-06-13-169/+493
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables and initialises DWMMC for SMDK5250. Supports both FDT and non-FDT. This patch creates a new file 'exynos5-dt.c' meant for FDT support. exynos5-dt.c: This file shall contain all code which supports FDT. Any addition of FDT support for any module needs to be added in this file. smdk5250.c: This file shall contain the code which supports non-FDT. version. Any addition of non-FDT support for any module needs to be added in this file. May be, the file smdk5250.c can be removed in near future when non-FDT is not required. The Makefile is updated to compile only one of the files exynos5-dt.c / smdk5250.c based on FDT configuration. NOTE: Please note that all additions corresponding to FDT need to be added into the file exynos5-dt.c. At same time if non-FDT support is required then add the corresponding updations into smdk5250.c. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* EXYNOS5: DWMMC: Initialise the local variable to avoid unwanted results.Amar2013-06-13-2/+2
| | | | | | | | | | | | This patch initialises the local variable 'shift' to zero. The uninitialised local variable 'shift' had garbage value and was resulting in unwnated results in the functions exynos5_get_mmc_clk() and exynos4_get_mmc_clk(). Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* EXYNOS5: DWMMC: Added FDT support for DWMMCAmar2013-06-13-17/+124
| | | | | | | | | | | This patch adds FDT support for DWMMC, by reading the DWMMC node data from the device tree and initialising DWMMC channels as per data obtained from the node. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* DWMMC: Initialise dwmci and resolve EMMC read write issuesAmar2013-06-13-9/+12
| | | | | | | | | | | | This patch enumerates dwmci and set auto stop command during dwmci initialisation. EMMC read/write is not happening in current implementation due to improper fifo size computation. Hence modified the fifo size computation to resolve EMMC read write issues. Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* EXYNOS5: FDT: Add DWMMC device node dataAmar2013-06-13-0/+111
| | | | | | | | | | | This patch adds DWMMC device node data for exynos5. This patch also adds binding file for DWMMC device node. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* FDT: Add compatible string for DWMMCAmar2013-06-13-0/+2
| | | | | | | | | Add required compatible information for DWMMC driver. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* arm:trats: change auto-booting to boot kernel with separate device tree blobArkadiusz Wlodarczyk2013-06-13-4/+13
| | | | | | | | Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos: Update origen and smdkv310 to use common tzpc_initInderpal Singh2013-06-04-125/+8
| | | | | | Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos: update tzpc to make it common for exynos4 and exynos5Inderpal Singh2013-06-04-18/+31
| | | | | | | | | | This requires that cpu_is_exynos4/5 should be made available before tzpc_init. Hence this patch also makes necessary changes to have cpu_info in spl and invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos: move tzpc_init to armv7/exynosInderpal Singh2013-06-04-30/+30
| | | | | | | | | | | tzpc_init is common for all exynos5 boards, hence move it to armv7/exynos so that all other boards can use it. Also update the smdk5250 Makefile and config file. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos: uart: s5p: enabling the uart tx/rx fifoAkshay Saraswat2013-05-21-4/+9
| | | | | | | | | | | | This patch enables the uart tx/rx fifo. Now that fifo is enabled, the uart read/write functions are modfied to check the UFSTAT register for fifo status instead of UTRSTAT (as required with fifo's enabled). Tested by booting linux kernel. Before enabling tx/rx fifo "Uncompressing linux" message is garbled and after enabling it is proper. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos5: clock: Update the equation to calculate PLL output frequencyAkshay Saraswat2013-05-21-4/+2
| | | | | | | | | | | | | | According to the latest exynos5 user manual, the equation for calculating PLL output was changed to FOUT= MDIV x FIN/(PDIV x 2^SDIV) earlier it was FOUT= MDIV x FIN/(PDIV x 2^(SDIV -1)) So updating the clock code accordingly. Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDK5250: Enable SPI Gigabyte device.Rajeshwari Shinde2013-05-20-0/+1
| | | | | | | | This patch enables gigabyte device for SMDK5250. Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SF: Add driver for Gigabyte device GD25LQ and GD25Q64BRajeshwari Shinde2013-05-20-0/+86
| | | | | | | | | | This patch adds driver for the gigabyte devices GD25LQ and GD25Q64B required for Snow Board. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* at91sam9260ek: move board id setup to config headerAndreas Bießmann2013-05-12-12/+18
| | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Bo Shen <voice.shen@atmel.com>
* mmc: atmel_mci: add mmc card supportBo Shen2013-05-12-1/+4
| | | | | | | add mmc card support with atmel mci driver Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* mmc: atmel_mci: using IP version for different settingBo Shen2013-05-12-4/+40
| | | | | | | | | Using IP version for different setting - Higher version supports 8bit mode - Higher version bus width setting is different Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: add at91sam9g20ek_mmc_config, which can save environment in mmc cardWu, Josh2013-05-12-1/+18
| | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: enable mci support for at91sam9g20ek.Wu, Josh2013-05-12-2/+28
| | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: add at91sam9n12ek board supportWu, Josh2013-05-12-2/+699
| | | | | | | | | | | | Add support for following features: - nand boot, with PMECC 2bit ECC for 512 bytes sector - SPI flash boot - SD card boot - LCD support Signed-off-by: Josh Wu <josh.wu@atmel.com> [fix -Wimplicit-function-declaration for at91_lcd_hw_init()] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: add at91sam9n12 register definitionWu, Josh2013-05-12-8/+32
| | | | | | | | Since at91sam9n12 is a subset of at91sam9x5, so put all at91sam9n12 definitions in at91sam9x5 head file. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* spi: atmel_spi: using ip version to check whether has wdrbtBo Shen2013-05-12-4/+13
| | | | | | | | | | | Using IP version to check whether it has wdrbt bit in mode register Tested in at91sam9x5ek and at91sam9n12ek. Signed-off-by: Bo Shen <voice.shen@atmel.com> [fix warning about incompatible parameter] Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-11-422/+1561
|\
| * ARM: OMAP: Add arch_cpu_init functionSRICHARAN R2013-05-10-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | The boot parameters passed from SPL to UBOOT must be saved as a part of uboot's gd data as early as possible, before we will inadvertently overwrite it. So adding a arch_cpu_init for the required Socs to save it. Signed-off-by: Sricharan R <r.sricharan@ti.com> [trini: Add igep0033 hunk] Signed-off-by: Tom Rini <trini@ti.com>
| * ARM: OMAP: Cleanup boot parameters usageSRICHARAN R2013-05-10-91/+39
| | | | | | | | | | | | | | | | | | | | | | The boot parameters are read from individual variables assigned for each of them. This been corrected and now they are stored as a part of the global data 'gd' structure. So read them from 'gd' instead. Signed-off-by: Sricharan R <r.sricharan@ti.com> [trini: Add igep0033 hunk] Signed-off-by: Tom Rini <trini@ti.com>
| * ARM: OMAP: Correct save_boot_params and replace with 'C' functionSRICHARAN R2013-05-10-7/+56
| | | | | | | | | | | | | | | | | | | | | | Currently save_boot_params saves the boot parameters passed from romcode. But this is not stored in a writable location consistently. So the current code would not work for a 'XIP' boot. Change this by saving the boot parameters in 'gd' which is always writable. Also add a 'C' function instead of an assembly code that is more readable. Signed-off-by: Sricharan R <r.sricharan@ti.com>
| * ARM: OMAP4/5: Make OMAPx_SRAM_SCRATCH_ defines commonSRICHARAN R2013-05-10-33/+24
| | | | | | | | | | | | | | | | These defines are same across OMAP4/5. So move them to omap_common.h. This is required for the patches that follow. Signed-off-by: Sricharan R <r.sricharan@ti.com>
| * ARM: OMAP: Make omap_boot_parameters common across socsSRICHARAN R2013-05-10-72/+49
| | | | | | | | | | | | | | | | omap_boot_parameters is same and defined for each soc. So move this to a common place to reuse it across socs. Signed-off-by: Sricharan R <r.sricharan@ti.com>
| * am33xx: Fix warning with CONFIG_DISPLAY_CPUINFOTom Rini2013-05-10-5/+1
| | | | | | | | | | | | | | | | The arm_freq and ddr_freq variables are unused, so remove. Fixup whitespace slightly while in here. Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Tom Rini <trini@ti.com>
| * davinci: handle CONFIG_SYS_CLE_MASK and CONFIG_SYS_ALE_MASKEric Benard2013-05-10-8/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | these variables are curently defined in several config files but the driver doesn't use them and defaults to hardcoded values in nand_defs.h It's interesting to be able to change this hardcoded valude when the hardware is not using the default adress signals to drive ALE and CLE and two configuration defines already exist for this purpose so use them. Signed-off-by: Eric Bénard <eric@eukrea.com>
| * da850: provide davinci_enable_uart0Eric Benard2013-05-10-0/+10
| | | | | | | | | | | | | | | | this is needed to bring UART0 out of reset but this function currently only exists for dm644x/355/365/646x when da850 (at least am1808 also need it). Signed-off-by: Eric Bénard <eric@eukrea.com>
| * cm-t35: update config fileIgor Grinberg2013-05-10-13/+5
| | | | | | | | | | | | | | Several minor updates to the cm-t35 config file. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
| * MAINTAINERS: fix the cm-t35 board nameIgor Grinberg2013-05-10-1/+1
| | | | | | | | | | | | | | "cm-t35" in U-Boot source code is called "cm_t35". Make the change "cm-t35" -> "cm_t35" for better greppability. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
| * cm-t35: move cm-t35 to live in compulab directoryIgor Grinberg2013-05-10-10/+11
| | | | | | | | | | | | | | | | | | Currently the cm-t35 support code lives under board/cm_t35 directory. Some of the code can be shared with other/future CompuLab boards, so move the cm-t35 to live under board/compulab/cm_t35 directory. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
| * ARM: Panda: Add flag to allow runtime enviroment varibale modsDan Murphy2013-05-10-0/+2
| | | | | | | | | | | | | | | | Add the flag to allow runtime enviroment variable modifications. This is being added so that the board-name can be modified at runtime to indicate either a panda(4430) or a panda-es(4460) Signed-off-by: Dan Murphy <dmurphy@ti.com>
| * ARM:Panda:Fix device tree loading for the panda-esDan Murphy2013-05-10-1/+9
| | | | | | | | | | | | | | | | | | | | | | Fix the device tree loading for panda(4430) and panda-es(4460) Modify the board name if a 4460 panda or panda-es is detected at run time. In the findfdt add a check for the panda-es board name and load the panda-es device tree blob. Signed-off-by: Dan Murphy <dmurphy@ti.com>
| * ARM: OMAP5: Fix warm reset with USB cable connectedLokesh Vutla2013-05-10-0/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Warm reset on OMAP5 freezes when USB cable is connected. Fix requires PRM_RSTTIME.RSTTIME1 to be programmed with the time for which reset should be held low for the voltages and the oscillator to reach stable state. There are 3 parameters to be considered for calculating the time, which are mostly board and PMIC dependent. -1- Time taken by the Oscillator to shut + restart -2- PMIC OTP times -3- Voltage rail ramp times, which inturn depends on the PMIC slew rate and value of the voltage ramp needed. In order to keep the code in u-boot simple, have a way for boards to specify a pre computed time directly using the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' option. If boards fail to specify the time, use a default as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead. Using the default value translates into some ~22ms and should work in all cases. However in order to avoid this large delay hiding other bugs, its recommended that all boards look at their respective data sheets and specify a pre computed and optimal value using 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' In order to help future board additions to compute this config option value, add a README at doc/README.omap-reset-time which explains how to compute the value. Also update the toplevel README with the additional option and pointers to doc/README.omap-reset-time. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [rnayak@ti.com: Updated changelog and added the README] Signed-off-by: Rajendra Nayak <rnayak@ti.com>
| * Remove duplicate / unused #defines on AM335x boardsMark Jackson2013-05-10-11/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | As part of a review of a recent patch to add a new AM335x board, Tom found several duplicate and/or unused #defines. This patch simply removes them. The two affected configs have been recompiled to check nothing was broken (from a compilation point of view !!) Reported-by: Tom Rini <trini@ti.com> Signed-off-by: Mark Jackson <mpfj-list@mimc.co.uk>
| * omap5_common: Add optargs variable for kernel command line argsTom Rini2013-05-10-0/+2
| | | | | | | | | | | | | | | | Add 'optargs' variable to be set to additional kernel arguments, similar to omap3*/am3* usage. Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
| * OMAP5: USB: hsusbtll_clkctrl has to be in hw_auto for USB to workLubomir Popov2013-05-10-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | USB TLL clocks do not support 'explicit_en', only 'hw_auto' control (R. Sricharan). cm_l3init_hsusbtll_clkctrl has to be moved to the clk_modules_hw_auto_essential[] array in order to make the clock work. This fix is needed (but not sufficient) for USB EHCI operation in U-Boot. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
| * ARM: Add support for IGEP COM AQUILA/CYGNUSEnric Balletbo i Serra2013-05-10-0/+680
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IGEP COM AQUILA and CYGNUS are industrial processors modules with following highlights: o AM3352/AM3354 Texas Instruments processor o Cortex-A8 ARM CPU o 3.3 volts Inputs / Outputs use industrial o 256 MB DDR3 SDRAM / 128 Megabytes FLASH o MicroSD card reader on-board o Ethernet controller on-board o JTAG debug connector available o Designed for industrial range purposes Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
| * Add DDR3 support for IGEP COM AQUILA/CYGNUS.Enric Balletbo i Serra2013-05-10-0/+17
| | | | | | | | | | | | These boards uses Samsung K4B2G1646E-BIH9 a 2Gb E-die DDR3 SDRAM. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
| * arm: omap: emif: Fix DDR3 init after warm resetLokesh Vutla2013-05-10-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EMIF supports a global warm reset mode, during which the EMIF keeps the SDRAM content. But if leveling is enabled at the time of warm reset for DDR3, the following steps needs to be done after warm reset: 1) Keep EMIF in self refresh mode. 2) Reset PHY to bring back the PHY to a known state. 3) Start Levelling procedure. Doing the same. And also enabling DLL lock and code output after warm reset. Tested on OMAP5432 ES2.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * beagleboard: Update comment in get_board_rev()Tom Rini2013-05-10-2/+3
| | | | | | | | | | | | | | | | We are able to tell the difference between xM Rev Ax/Bx and xM Rev Cx, and have been for some time. The comment above the function however did not list this, so update. Signed-off-by: Tom Rini <trini@ti.com>
generated by cgit v1.1 at 2024-12-11 20:12:38 +0000