summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* ENGR00139215 iMX61 Uboot support blow fuseRyan QIAN2011-11-02-0/+846
| | | | | | | | 1. add force option to blow operation 2. add blown value check 3. add simple validation for zeros returned by 'simple_strtoul' call Signed-off-by: Ryan QIAN <b32804@freescale.com>
* ENGR00161126 Enable Hush parser in MX6Q Sabrelite configMahesh Mahadevan2011-11-01-0/+4
| | | | | | | Enable the Hush parser in the Sabrelite config to parse boot scripts. Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00161133: Add spi-nor support for mx6qTerry Lv2011-11-01-2/+83
| | | | | | Add spi-nor support for mx6q. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00161125 Update MX6Q Sabrelite config to boot from MMC by defaultMahesh Mahadevan2011-10-31-2/+2
| | | | | | Boot from MMC by default and disable DHCP by default on MX6Q Sabrelite Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00161004 MX6Q Uboot Rename sabreauto to arm2 boardAnish Trivedi2011-10-28-32/+48
| | | | | | | | | Sabreauto is an inaccurate name for the Armadillo2 board that this code is actually meant for. So, replaced "sabreauto" in folder names, file names, configs, and code with "arm2". Created a new machine id for ARM2 board. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00139221 USDHC Add SDXC UHS-I supportAnish Trivedi2011-10-27-26/+344
| | | | | | | Modified MMC library for UHS-I command sequence Added support to USDHC driver for UHS-I Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00160514: clean up compiler warning for mx6qTerry Lv2011-10-26-2/+3
| | | | | | Clean up compiler warning. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00160399 Added support for the MX6Q Sabre-lite boardMahesh Mahadevan2011-10-25-82/+1480
| | | | | | Includes support for uSDHC read, write, FEC, SPI-NOR etc. Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00160725 fastboot: fix the serial number display errorXinyu Chen2011-10-25-1/+1
| | | | | | Incorrect usb string package size assign. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00160507 Update the IOMUX implementation for MX6Mahesh Mahadevan2011-10-20-6/+5
| | | | | | | The MX6 code incorrectly uses the Hysteresis bit to decide NO_PAD_CTRL operation Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00156934: Update mx35 AIPS max dbg m3if esdctl settingsTerry Lv2011-10-18-18/+32
| | | | | | | This patch is to fix mx35 TVIN flicker issue. It will change AIPS, M3IF, MAX, DBG and esdctl settings. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00156930: Update MX35 DDR2 scriptsTerry Lv2011-10-18-81/+451
| | | | | | | | | | Update MX35 DDR2 scripts for that when enabling 256MB, the CSD1 is not stable. 1. Add CSD1 configs to support 256M RAM. 2. Add mx35 TO2 256M RAM configs. 3. Update DDR init code in lowlevel_init.S for external boot. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139279-3 MX6Q: invalidate the D-CACHEHuang Shijie2011-10-14-0/+37
| | | | | | | | | | | The USB boot mode does not invalidate the D-CACHE, so the uboot will DEAD when it tries to invalidate the random data in the cache line. The MMC boot will do the MMU init which will do the D-CACHE invalidation. So the MMC boot will ok in the boot procedure. Signed-off-by: Huang Shijie <b32955@freescale.com>
* ENGR00139279-2 MX6Q: add mfgtool supportHuang Shijie2011-10-14-0/+269
| | | | | | add the MFGTOOL support for mx6q. Signed-off-by: Huang Shijie <b32955@freescale.com>
* ENGR00139279-1 MX6Q: add env_embedded module for CONFIG_ENV_IS_NOWHEREHuang Shijie2011-10-14-0/+1
| | | | | | | The env_embedded module is a built-in module. So add the module when the CONFIG_ENV_IS_NOWHERE is enabled. Signed-off-by: Huang Shijie <b32955@freescale.com>
* ENGR00159845 [MX6]lpddr2 board, put MMDC into power saving modeAnson Huang2011-10-13-2/+10
| | | | | | | | For lpddr2 board. 1. Put mmdc into power saving mode; 2. Do the necessary setting for AXI cache and IPU Qos. Signed-off-by: Anson Huang <b20788@freescale.com>
* ENGR00159740 Android: Fastboot: enlarge max image size to 148MBZhang Jiejing2011-10-12-5/+5
| | | | | | | enlarge max image size to 148MB from 128MB. since android become bigger. so 128M not enough. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00159696 [MX6]Enable lpddr2 boardAnson Huang2011-10-11-0/+452
| | | | | | | And new config to enable lpddr2 board with H9TKNNN4KDMPQR-NDM chip. Signed-off-by: Anson Huang <b20788@freescale.com>
* ENGR00158184 mx53 smd: use highest value for unknown board revision valueWayne Zou2011-09-26-1/+5
| | | | | | mx53 smd: use highest value for unknown board revision value Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00157538 remove VDIG_PLL setting in plug-in codeLily Zhang2011-09-23-20/+0
| | | | | | | | According to the datasheet, VDIG_PLL needs to be increased to 1.3v for TO2.0. This operation has been done in the low_level_init.S. Remove the duplicated code here. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00157468: Fix default environment's "mmc dev" type errorTerry Lv2011-09-23-14/+14
| | | | | | | Some semicolons are missed after "mmc dev 0". They need to be added to make default environment work. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00157419: Correct default environment's mmc device in mx6qTerry Lv2011-09-22-1/+1
| | | | | | | Default environment in mx6q uses mmc device 0. We should use mmc device 3. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00155569 mc34708: change global reset time as 4s of LOCO and PCBARobin Gong2011-09-19-0/+22
| | | | | | reduce the time of global reset to 4s in the boards of loco and pcba Signed-off-by: Robin Gong <B38343@freescale.com>
* ENGR00156670-2 MMC: Fixed some bugs in common codeAnish Trivedi2011-09-13-2/+2
| | | | | | | | | | | | | Need to send RCA when sending CMD13. Cannot use print_size function when displaying card capacity because it expects a 32 bit integer as input, while mmc->capacity is a 64 bit integer. There is loss of information leading to incorrect capacities being displayed for "mmcinfo" cmd. Changed it to simply print the entire 64 bit integer, which is the number of bytes. Signed-off-by: Tony Lin <tony.lin@freescale.com> Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00156670-1 ESDHC/USDHC: Remove delay before each cmd and some bug fixesAnish Trivedi2011-09-13-8/+13
| | | | | | | | | | | | Removed delay of 10 ms before each command. There should not be a need to have this delay after the ENGR00156405 patch that polls until card is not busy anymore before proceeding to next cmd. Added poll on reset bits of controller after the bits are set to wait until they clear before proceeding further. Signed-off-by: Tony Lin <tony.lin@freescale.com> Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00156405 ESDHC: Add workaround for auto-clock gate errata ENGcm03648Anish Trivedi2011-09-13-2/+34
| | | | | | | | | | | | The errata, not applicable to USDHC, causes ESDHC to shut off clock to the card when auto-clock gating is enabled for commands with busy signalling and no data phase. The card might require the clock to exit the busy state, so the workaround is to disable the auto-clock gate bits in SYSCTL register for such commands. The workaround also entails polling on DAT0 bit in the PRSSTAT register to learn when busy state is complete. Auto-clock gating is re-enabled at the end of busy state. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00156389: turn off child clocks before reconfigure perclk_rootTerry Lv2011-09-13-0/+75
| | | | | | | | | | | | | | | | | | | | | | | | | In addition to ensuring that PERCLK remains at least 2.5 times slower than the AHB clock, certain steps need to be followed to ensure robust operation of PERCLK when reconfiguring the PERCLK clock source. To properly configure the PERCLK clock source, the following steps are required: 1.In the CCGR registers, gate the clocks to all PERCLK-dependent modules. 2.Select the desired input clock for the PERCLK root clock (to be either source from the peripherals main source clock or the lp_apm clock source). Refer to the CMCBR register, perclk_lp_apm_sel bit. 3.Configure the perclk_pred1, perclk_pred2, and perclk_podf dividers to the desired setting. Refer to the CBCDR register for details. 4.In the CCGR registers, enable the desired clocks for the PERCLK-dependent module clocks. Certain steps are required to reconfigure perclk_root. If don't follow these steps, GPT timer may stop and the kernel stops at " "Calibrating delay loop". Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00156304 eMMC: Need to update partition config after changing boot partitionAnish Trivedi2011-09-08-32/+33
| | | | | | | | | | | | | | | | After enabling boot partition on an eMMC using "mmc bootpart" command, the partition configuration variable that is supposed to track this value on the eMMC is not updated. This leads to stale and possibly inaccurate boot partition number being printed when "mmcinfo" command is used, thereby confusing the user. The fix is to update the part_config variable of mmc struct with the new value that was just written to the eMMC. Also removed condition that restricted boot_bus_width programming (for fastboot) to eMMC with DDR support only. Now, even non-DDR capable eMMCs can be programmed for fastboot (in SDR mode). Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00156098 mx53_smd/mx53_loco: DA9053 I2C SDA stuck low issue on bootupWayne Zou2011-09-06-2/+204
| | | | | | | | | | | | | | | | For DA9053 I2C SDA stuck low issue: the I2C block in DA9053 may not correctly receive a Power On Reset and device is in unknown state during start-up. The only way to get the chip into known state before any communication with the Chip via I2C is to dummy clock the I2C and bring it in a state where I2C can communicate. Dialog suggested to provide 9 clock on SCL. Dialog don't know the exact reason for the fault and assume it is because some random noise or spurious behaviour. This has to been done in host platform specific I2C driver during start-up when the I2C is being configured at platform level to supply with dummy 9 clock on SCL. Dialog I2C driver has no control to provide dummy 9 clock on SCL. Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00156034: Fix mx53 evk build errorTerry Lv2011-09-05-1/+0
| | | | | | Fix mx53 evk build error. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139254: Enable MX6Q Uboot Splash ScreenSandor Yu2011-09-02-63/+441
| | | | | | | | | | | | | | Only support LVDS0 splash screen. Enable splash process: 1.define CONFIG_SPLASH_SCREEN in mx6q_sabreauto.h 2.Config U-boot with followed command:() setenv splashimage '0x30000000' #Set splash position as Center setenv splashpos 'm,m' #Set LVDS via LVDS bridge 0 setenv lvds_num 0 Signed-off-by: Sandor Yu <r01008@freescale.com>
* ENGR00155283: Set dpgdck0_2_en to 0 when freq is lower than 300MHzTerry Lv2011-09-01-13/+54
| | | | | | | | 1. Set dpgdck0_2_en to 0 when required freq is lower than 300Mhz. 2. When dpgdck0_2_en is 0, the formula to calculate output freq will be changed to 2 * freq * []. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00155279: Change ESDCTL_0x82228080 to ESDCTL_0x82226080 for mx35Terry Lv2011-09-01-3/+4
| | | | | | | | | | In mx35, when testing TVIN, the screen will flick. We find that flickers will get better when using ESDCTL_0x82226080 against ESDCTL_0x82228080 for register SCDCTL0. The origin value ESDCTL_0x82228080 in lowlevel_init.S will be called in external boot which will reduce the bandwidth. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00155739: mx53 evk mmu wrong mapped two csd slotsTerry Lv2011-09-01-10/+4
| | | | | | | mx53 evk mmu wrong mapped two csd slots. Actually evk only has one slot. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154666-4: Align u-boot mmc command with communityTerry Lv2011-09-01-14/+11
| | | | | | | Change fastboot code for that fastboot uses mmc command to access card. Thus the code need to be modified to new mmc command. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154666-3: Align u-boot mmc command with communityTerry Lv2011-09-01-571/+918
| | | | | | | | | | | This patch will enhance mmc command. 1. Add erase command. 2. Abandon dev_no in mmc command. User need to switch slot with "mmc dev" command. 3. Add mmc part switch command. Enhance partition switch support. 4. Add mmc bootpart. Boot partition support is more flexible. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154666-2: Align u-boot mmc command with communityTerry Lv2011-09-01-5/+5
| | | | | | Trivial change to remove build warnings. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154666-1: Align u-boot mmc command with communityTerry Lv2011-09-01-84/+92
| | | | | | | | Modifications on config files. 1. Remove CONFIG_BOOT_PARTITION_ACCESS. 2. Change all mmc read command in default env configs. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00155284 mx53_smd: move I2C access to board_init_late for system hang issueWayne Zou2011-08-31-9/+12
| | | | | | | | | | | | MX53 SMD hangs if reset many times with lower possibility. If doing I2C access in early time, I2C may cause system hangs. So moving I2C access to late phase to make system hang issue disappear. QA Test result: QA raised 6 full rounds of CTS one-round test Totally ran for 6 rounds about 27 hours, reboot for 56*6=336 times, no reboot failure occurred. Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00155472 mx53_loco: support both of RevA and RevB in ubootRobin Gong2011-08-29-4/+18
| | | | | | to fix we should amend systemrev in uboot, add new board RevB for it Signed-off-by: Robin Gong <B38343@freescale.com>
* ENGR00154672: Change to use rom plugins for mx53 boardsTerry Lv2011-08-29-465/+889
| | | | | | | | | | | | | 1. As customer required, we change to use rom plugins for mx53 boards. Tested pass with latest mfg tools. 2. Update DDR3 script based on MX53_TO2_DDR3_LCB_SMD_ARDb_v2.inc. Got from http://compass.freescale.net/livelink/livelink?func=ll &objId=221058910&objAction=browse&viewType=1. 3. Fix a tiny build error in mx53_smd.c. This error will happen when building mx53_smd_mfg. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00155240 mx53_smd: Fix a bug that hangs on printf() in board_initWayne Zou2011-08-23-5/+1
| | | | | | remove printf() because serial interface is not ready in board_init() Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00155133: Add sata support for imx6Terry Lv2011-08-22-0/+64
| | | | | | Init clocks, phy and pll for sata. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00151255 mx53 QS: Enable VUSB_2V5Lily Zhang2011-08-22-0/+15
| | | | | | | | | Kernel stops at USB driver initialization if suspending, resuming and resetting the board. It's because VUSB_2V5 voltage is disabled after suspend. Need to re-enable it mannually into U-boot Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00155156 [MX6]Clean up debug info in ubootAnson Huang2011-08-22-25/+1
| | | | | | | | 1. ENET don't need to enable ENET pll clock; 2. Enable cpu debug clock in case of using JTAG; 3. Clean up some debug info during bring up. Signed-off-by: Anson Huang <b20788@freescale.com>
* ENGR00155138 mx53_smd/mx53_loco: Add i2c retry to fix DA9053 i2c NAK issueWayne Zou2011-08-22-3/+20
| | | | | | | | | when board boots up, during the iMX53 SOC does DA9053 Read/Write operation, it writes slave address and wait for ACK . Instead of ACK PMIC sends NAK. A workaround fix is provided as a part of retries to fix I2C NAK for very first access. Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00155018 mx53_pcba: update Ripley AUX input to 950mA and charge currentWayne Zou2011-08-19-2/+3
| | | | | | | set Ripley AUX input current limit to 950mA and set charge termination current to 400mA Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00154998 mx53 pcba: correct the default bootargsXinyu Chen2011-08-18-29/+9
| | | | | | Default boot up with the 7' LCD on. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00154924 [MX6]Disable some clocks in ubootAnson Huang2011-08-17-2/+7
| | | | | | | | | | | We should disabel some clocks in uboot to save power, or when we download from enet to boot up kernel, the power consumption could be up 800mA@5V, may damage the chip. After apply it, we can save more then 200mA@5V. Signed-off-by: Anson Huang <b20788@freescale.com>
* ENGR00154396: U_BOOT: Env config adjustment.Terry Lv2011-08-12-85/+85
| | | | | | | Change env size to 8K and change gpmi nand env offset to 2M. This will reduce boot time and fix gpmi nand env problem. Signed-off-by: Terry Lv <r65388@freescale.com>
generated by cgit v1.1 at 2024-12-24 20:03:14 +0000