summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discreteShengzhou Liu2016-03-21-8/+82
| | | | | | | | | | Add support of address parity for DDR4 UDIMM or discrete memory. It requires to configurate corresponding MR5[2:0] and TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig, e.g. hwconfig=fsl_ddr:parity=on. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* pci/layerscape: set LUT and msi-map for discovered PCI devicesStuart Yoder2016-03-21-0/+147
| | | | | | | | | | | | | | | | | | msi-map properties are used to tell an OS how PCI requester IDs are mapped to ARM SMMU stream IDs. for all PCI devices discovered in a system: -allocate a LUT (look-up-table) entry in that PCI controller -allocate a stream ID for the device -program and enable a LUT entry (maps PCI requester id to stream ID) -set the msi-map property on the controller reflecting the LUT mapping basic bus scanning loop/logic was taken from drivers/pci/pci.c pci_hose_scan_bus(). Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* pci/layerscape: add defines for LUTStuart Yoder2016-03-21-0/+4
| | | | | | | | | | The per-PCI controller LUT (Look-Up-Table) is a 32-entry table that maps PCI requester IDs (bus/dev/fun) to a stream ID. Add defines for the register offsets. Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* pci: make pci_get_hose_head() available to external usersStuart Yoder2016-03-21-0/+1
| | | | | | | | | Put pci_get_hose_head() prototype in header so it is available to external users, allowing them to find and iterate over all pci controllers. Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls2080a: update stream ID partitioning infoStuart Yoder2016-03-21-21/+34
| | | | | | | | | Update comments around how stream IDs are partitioned. Stream IDs allocated to PCI are no longer divided up by controller, but are instead a contiguous range Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls2080a: remove obsolete stream ID partitioning supportStuart Yoder2016-03-21-183/+0
| | | | | | | | | | Remove stream ID partitioning support that has been made obsolete by upstream device tree bindings that specify how representing how PCI requester IDs are mapped to MSI specifiers and SMMU stream IDs. Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* boards: ls2080: Fix default bootargsYork Sun2016-03-21-2/+2
| | | | | | A white space is missing in multiple-line string for bootargs. Signed-off-by: York Sun <york.sun@nxp.com>
* arm: ls102xa: fdt: Update FSL_QSPI_COMPAT and FSL_DSPI_COMPATAlison Wang2016-03-21-2/+2
| | | | | | | | | As the compatible property values for QSPI and DSPI dts nodes are changed in kernel, FSL_QSPI_COMPAT and FSL_DSPI_COMPAT need to be updated too. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* drivers/crypto/fsl: define structures for PDBAneesh Bansal2016-03-21-0/+55
| | | | | | | | | | | Structures are defined for PDB (Protocol Data Blcks) for various operations. These structure will be used to add PDB data while creating the PDB descriptors. Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> CC: Ulises Cardenas <raul.casas@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* drivers/crypto/fsl: add constructs for protocol descriptorsAneesh Bansal2016-03-21-0/+52
| | | | | | | | | | Construct APIs are added to create Protocol Descriptors for CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> CC: Ulises Cardenas <raul.casas@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* drivers/crypto/fsl: correct error checking in run_descriptorAneesh Bansal2016-03-21-1/+1
| | | | | | | | | When CAAM runs a descriptor and an error occurs, a non-zero value is set in Output Status Register. The if condition should check the status for a non-zero value. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls2080ardb: invert irq pins polarity for AQR405 PHYShaohui Xie2016-03-21-0/+9
| | | | | | | | | To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins polarity by setting IRQCR register, because AQR405 interrupt is low active but GIC accepts high active. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: lsch3: Enable WUO config for RNI-20 nodePrabhakar Kushwaha2016-03-21-0/+31
| | | | | | | | | | Enable wuo config to accelerate coherent ordered writes for LS2080A and LS2085A. WRIOP IP is connected to RNI-20 Node. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* arm64: Fix layerscape mmu setupAlexander Graf2016-03-21-1/+6
| | | | | | | | | | | | | | | | | | With commit 7985cdf we converted all systems except for the Layerscape SoCs to the generic descriptor table based page table setup. On the Layerscape SoCs however, we just provide an empty table stub and do the setup ourselves. To reserve enough memory for the tables, we need to override the default counting mechanism which would end up with an empty table because we have no maps. Fixes: 7985cdf Reported-by: York Sun <york.sun@nxp.com> CC: Alison Wang <alison.wang@nxp.com> CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Alexander Graf <agraf@suse.de> Tested-by: York Sun <york.sun@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* cmd_dhry.c: Use lldiv for vax_mips calculation as wellTom Rini2016-03-17-1/+1
| | | | | | | | | | Since dhry_per_sec is a u64 we must also use lldiv here when working with it. Otherwise: ../lib/dhry/cmd_dhry.c:(.text.do_dhry+0xd8): undefined reference to `__udivdi3' On some platforms. Signed-off-by: Tom Rini <trini@konsulko.com>
* x86: Add congatec conga-QA3/E3845-4G (Bay Trail) supportStefan Roese2016-03-17-0/+506
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM, installed on the congatec Qseven 2.0 evaluation carrier board (conga-QEVAL). Its port is very similar to the MinnowboardMAX port and also uses the Intel FSP as described in doc/README.x86. Currently supported are the following interfaces / devices: - UART (via Winbond legacy SuperIO chip on carrier board) - Ethernet (PCIe Intel I210 / E1000) - SPI including SPI NOR as boot-device - USB 2.0 - SATA via U-Boot SCSI IF - eMMC - Video (HDMI output @ 800x600) - PCIe Not supported yet is: - I2C - USB 3.0 Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add support for the samus chromebookSimon Glass2016-03-17-1/+876
| | | | | | | | | | | | | | | | | | | | | | | This adds basic support for chromebook_samus. This is the 2015 Pixel and is based on an Intel broadwell platform. Supported so far are: - Serial - SPI flash - SDRAM init (with MRC cache) - SATA - Video (on the internal LCD panel) - Keyboard Various less-visible drivers are provided to make the above work (e.g. PCH, power control and LPC). The platform requires various binary blobs which are documented in the README. The major missing feature is USB3 since the existing U-Boot support does not work correctly with Intel XHCI controllers. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Support a chained-boot development flowSimon Glass2016-03-17-0/+80
| | | | | | | | | | | | | | | | | | Sometimes it is useful to jump into U-Boot directly from coreboot or UEFI without any 16-bit init. This can help during development by allowing U-Boot to avoid doing all the init required by the platform. U-Boot expects its GDT to be set up correctly by its 16-bit code. If coreboot doesn't do this (because it hasn't run the payload setup code yet) then this won't happen. In this case we cannot rely on the GDT settings. U-Boot will hang or crash if these are wrong. Provide a development-only option to set up the GDT correctly. This is just a hack so you can jump to U-Boot from any stage of coreboot, not just at the end. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: dts: Drop memory SPD compatible stringSimon Glass2016-03-17-3/+0
| | | | | | | | This is not needed now that the memory controller driver has the SPD data in its own node. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: ivybridge: Convert to use the common SDRAM codeSimon Glass2016-03-17-311/+83
| | | | | | | Adjust the existing implementation to use the new common SDRAM init code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add common SDRAM-init codeSimon Glass2016-03-17-0/+327
| | | | | | | | | The code to call the memory reference code is common to several Intel CPUs. Add common code for performing this init. Intel calls this 'Pre-EFI-Init' (PEI), where EFI stands for Extensible Firmware Interface. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Move common PCH code into a common placeSimon Glass2016-03-17-84/+99
| | | | | | | | The SATA indexed register write functions are common to several Intel PCHs. Move this into a common location. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* dhry: Correct dhrystone calculation for fast machinesSimon Glass2016-03-17-3/+5
| | | | | | | At present samus reports about 5600 DMIPS. With the default iteration count this is OK, but if 10 million runs are performed it overflows. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: Add a 64-bit division routine to the private librarySimon Glass2016-03-17-1/+247
| | | | | | | | | | | | This is missing, with causes lldiv() to fail on boards with use the private libgcc. Add the missing routine. Code is available for using the CLZ instruction but it is not enabled at present. This comes from coreboot version 4.0. Signed-off-by: Simon Glass <sjg@chromium.org>
* x86: Fix a header nit in x86-chromebook.hSimon Glass2016-03-17-1/+0
| | | | | | | There is an extra line in the comment in the header. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add a function to set the IOAPIC IDSimon Glass2016-03-17-0/+18
| | | | | | | Add a function to set the ID in the IOAPIC. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Update README for new developmentsSimon Glass2016-03-17-3/+13
| | | | | | | Update a few points which have become out-of-date. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Use white on black for the console on chromebooksSimon Glass2016-03-17-0/+2
| | | | | | | | This is a little easier on the eyes, particularly when the backlight is set to maximum. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add a default address for reference codeSimon Glass2016-03-17-0/+2
| | | | | | | | Add an address which can be used for loading and running the reference code when needed. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add video supportSimon Glass2016-03-17-1/+1174
| | | | | | | | | | | | | | Add a video driver for Intel's broadwell integrated graphics controller. This uses a binary blob for most init, with the driver just performing a few basic tasks. This driver supports VESA as the mode-setting mechanism. Since most boards don't support driver model yet with VESA, a special case is added to the Kconfig for broadwell. Eventually all boards will use driver model and this can be removed. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add support for high-speed I/O lane with MESimon Glass2016-03-17-0/+58
| | | | | | | | Provide a way to determine the HSIO (high-speed I/O) version supported by the Intel Management Engine (ME) implementation on the platform. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add a GPIO driverSimon Glass2016-03-17-0/+208
| | | | | | | Add a GPIO driver for the GPIO peripheral found on broadwell devices. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add support for SDRAM setupSimon Glass2016-03-17-0/+509
| | | | | | | | | Broadwell uses a binary blob called the memory reference code (MRC) to start up its SDRAM. This is similar to ivybridge so we can mostly use common code for running this blob. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add power-control supportSimon Glass2016-03-17-0/+220
| | | | | | | | | | Broadwell requires quite a bit of power-management setup. Add code to set this up correctly. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com> [squashed in http://patchwork.ozlabs.org/patch/598373/] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add reference code supportSimon Glass2016-03-17-0/+114
| | | | | | | | Broadwell needs a special binary blob to set up the PCH. Add code to run this on start-up. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add an LPC driverSimon Glass2016-03-17-0/+110
| | | | | | | | Add a driver for the broadwell LPC (low-pin-count peripheral). This mostly uses common code. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add a northbridge driverSimon Glass2016-03-17-0/+60
| | | | | | | | Add a driver for the broadwell northbridge. This sets up the location of several blocks of registers. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add a SATA driverSimon Glass2016-03-17-0/+270
| | | | | | | | Add a SATA driver for broadwell. This supports connecting an SSD and the usual U-Boot commands to read and write data. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add a pinctrl driverSimon Glass2016-03-17-0/+590
| | | | | | | | | | | GPIO pins need to be set up on start-up. Add a driver to provide this, configured from the device tree. The binding is slightly different from the existing ICH6 binding, since that is quite verbose. The new binding should be just as extensible. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: broadwell: Add a PCH driverSimon Glass2016-03-17-0/+839
| | | | | | | Add a driver for the broadwell low-power platform controller hub. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add basic support for broadwellSimon Glass2016-03-17-0/+1246
| | | | | | | | This adds the broadwell architecture, with the CPU driver and some useful header files. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
* x86: dts: Update the pinctrl binding a littleSimon Glass2016-03-17-10/+11
| | | | | | | Make a few minor updates to make the meaning clearer. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add support for running Intel reference codeSimon Glass2016-03-17-1/+36
| | | | | | | | | | | | Intel has invented yet another binary blob which firmware is required to run. This is run after SDRAM is ready. It is linked to load at a particular address, typically 0, but is a relocatable ELF so can be moved if required. Add support for this in the build system. The file should be placed in the board directory, and called refcode.elf. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Drop all the old pin configuration codeSimon Glass2016-03-17-334/+0
| | | | | | | | We don't need this anymore - we can use device tree and the new pinconfig driver instead. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: gpio: Allow the pinctrl driver to set up the pin configSimon Glass2016-03-17-175/+15
| | | | | | | | Rather than setting up the pin configuration in the GPIO driver, use the new pinctrl driver to do it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Add an ICH6 pin configuration driverSimon Glass2016-03-17-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a driver which sets up the pin configuration on x86 devices with an ICH6 (or later) Platform Controller Hub. The driver is not in the pinctrl uclass due to some oddities of the way x86 devices work: - The GPIO controller is not present in I/O space until it is set up - This is done by writing a register in the PCH - The PCH has a driver which itself uses PCI, another driver - The pinctrl uclass requires that a pinctrl device be available before any other device can be probed It would be possible to work around the limitations by: - Hard-coding the GPIO address rather than reading it from the PCH - Using special x86 PCI access to set the GPIO address in the PCH However it is not clear that this is better, since the pin configuration driver does not actually provide normal pin configuration services - it simply sets up all the pins statically when probed. While this remains the case, it seems better to use a syscon uclass instead. This can be probed whenever it is needed, without any limitations. Also add an 'invert' property to support inverting the input. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: link: Add pin configuration to the device treeSimon Glass2016-03-17-0/+155
| | | | | | | | | | | | At present pin configuration on link does not use the standard mechanism, but some rather ugly custom code. As a first step to resolving this, add the pin configuration to the device tree. Four of the GPIOs must be available before relocation (for SDRAM pin strapping). Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Update microcode for secondary CPUsSimon Glass2016-03-17-2/+12
| | | | | | | | Each CPU needs to have its microcode loaded. Add support for this so that all CPUs will have the same version. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: ivybridge: Show microcode version for each coreSimon Glass2016-03-17-1/+2
| | | | | | | | Enable the microcode feature so that the microcode version is shown with the 'cpu detail' command. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* x86: Record the CPU details when starting each coreSimon Glass2016-03-17-1/+20
| | | | | | | | As each core starts up, record its microcode version and CPU ID so these can be presented with the 'cpu detail' command. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit v1.1 at 2024-08-21 16:40:25 +0000