summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* powerpc/t1023rdb: Add T1023 RDB board supportShengzhou Liu2015-05-04-44/+382
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC. T1023RDB board Overview ----------------------- - T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - one 1G RGMII port on-board(RTL8211F PHY) - one 1G SGMII port on-board(RTL8211F PHY) - one 2.5G SGMII port on-board(AQR105 PHY) - PCIe: Two Mini-PCIe connectors on-board. - SerDes: 4 lanes up to 10.3125GHz - NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash - NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash - eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash. - USB: one Type-A USB 2.0 port with internal PHY - eSDHC: support SD/MMC card and eMMC on-board - 256Kbit M24256 I2C EEPROM - RTC: Real-time clock DS1339 on I2C bus - UART: one serial port on-board with RJ45 connector - Debugging: JTAG/COP for T1023 debugging As well updated T1024RDB to add T1023RDB. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: fix defconfig files] Reviewed-by: York Sun <yorksun@freescale.com>
* fsl/pci: Set CFG_READY for PCIe v3.0 and laterMinghuan Lian2015-05-04-1/+8
| | | | | | | | | | | | | | Freescale PCIe controllers v3.0 and later need to set bit CFG_READY to allow all inbound configuration transactions to be processed normally when in EP mode. However, bit CFG_READY has been moved from PCIe configuration space to CCSR PCIe configuration register comparing previous version. The patch is to set this bit according to PCIe version. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* T2080QDS/PCIe: Soft Reset PCIe on T2080QDS for down-training issueZhao Qiang2015-05-04-0/+16
| | | | | | | | | T2080QDS PEX1/Slot#1 will down-train from x4 to x2, with SRDS_PRTCL_S1 = 0x66 and SRDS_PRTCL_S2 = 0x15. Soft reset PCIe can fix this issue. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t4rdb: Add SD boot support for T4240RDB boardChunhe Lan2015-05-04-16/+186
| | | | | | | | | | | | This patch adds SD boot support for T4240RDB board. SPL framework is used. PBL initializes the internal RAM and copies SPL to it. Then SPL initializes DDR using SPD and copies u-boot from SD card to DDR, finally SPL transfers control to u-boot. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> [York Sun: Fix T4240RDB_SDCARD_defcofig] Reviewed-by: York Sun <yorksun@freescale.com>
* drivers: usb: fsl: Workaround for Erratum A004477Nikhil Badola2015-05-04-0/+49
| | | | | | | | | | Add a delay of 1 microsecond before issuing soft reset to the controller to let ongoing ULPI transaction complete. This prevents corruption of ULPI Function Control Register which eventually prevents phy clock from entering to low power mode Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx/T4240EMU: Remove T4240EMU boardYork Sun2015-05-04-234/+0
| | | | | | | T4240 SoC has been available for a long time. Emulator support is no longer needed. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Use GOT when loading IVORs post-relocationScott Wood2015-05-04-15/+20
| | | | | | | | | | | | | | | | | | | | | Commit 96d2bb952bb ("powerpc/mpc85xx: Don't relocate exception vectors") simplified IVOR initialization a bit too much, failing to use the post-relocation offset. This doesn't cause a problem with normal NOR boot, in which both the pre-relocation and post-relocation addresses are 64 KiB aligned. However, if TEXT_BASE is only 4 KiB aligned, such as for NAND/SD/etc. boot on some targets, as well as the QEMU target, the post-relocation address will not be the same in the lower 16 bits, as reserve_uboot() ensures that the relocation address is always 64 KiB aligned even if the pre-relocation address was not. Use the GOT to get the proper post-relocation offsets. Fixes: 96d2bb952bb ("powerpc/mpc85xx: Don't relocate exception vectors") Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Alexander Graf <agraf@suse.de> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Tested-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini2015-04-29-50/+914
|\
| * ARM: zynq: rename CONFIG_ZYNQ to CONFIG_ARCH_ZYNQMasahiro Yamada2015-04-29-12/+12
| | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: move SoC headers to mach-zynq/include/machMasahiro Yamada2015-04-29-0/+0
| | | | | | | | | | | | | | | | Move arch/arm/include/asm/arch-zynq/* -> arch/arm/mach-zynq/include/mach/* Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: move SoC sources to mach-zynqMasahiro Yamada2015-04-29-4/+4
| | | | | | | | | | | | | | Move arch/arm/cpu/armv7/zynq/* -> arch/arm/mach-zynq/* Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: pass "-mfpu=neon" only to lowlevel_init.SMasahiro Yamada2015-04-29-7/+1
| | | | | | | | | | | | | | | | | | The comment line in arch/arm/cpu/armv7/zynq/config.mk says that the option "-mfpu=neon" is necessary for compiling lowlevel_init.S. We do not have to give it to all the source files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: Enable SDHCI0 optionsMichal Simek2015-04-29-0/+14
| | | | | | | | | | | | | | Enable SDHCI0 for zynqmp. Add empty gpio.h because of sdhci requirement. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: Enable FS_GENERIC optionSiva Durga Prasad Paladugu2015-04-29-2/+3
| | | | | | | | | | | | | | Provide an option to write filesystem independend commands. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: Add SPI driver support for ZynqMPSiva Durga Prasad Paladugu2015-04-29-0/+10
| | | | | | | | | | | | | | | | | | Added the SPI driver support for ZynqMP The controller is same as zynq SPI controller Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
| * zynqmp: i2c: Enable i2c driver for zynqMPSiva Durga Prasad Paladugu2015-04-29-0/+26
| | | | | | | | | | | | | | | | | | | | Enable the i2c driver for ZynqMP Also enable the eeprom for read and writes to eeprom on ZynqMP ZynqMP uses the same i2c controller as in Zynq Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: Add support for EMMC bootmodeMichal Simek2015-04-29-1/+3
| | | | | | | | | | | | Add support for EMMC bootmode. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: Add support for emulation platform - VeloceMichal Simek2015-04-29-2/+12
| | | | | | | | | | | | | | Add support for Veloce - zynqmp emulation platform. Platform doesn't support SDHCI. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynq: timer: Fix wrong timer calculationSiva Durga Prasad Paladugu2015-04-29-1/+3
| | | | | | | | | | | | | | | | | | | | Fix wrong timer calculation in get_timer_masked incase of overflow. This fixes the issue of getting wrong time from get_timer() calls. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: sdhci: Remove the quirk SDHCI_QUIRK_NO_CDSiva Durga Prasad Paladugu2015-04-29-1/+1
| | | | | | | | | | | | | | | | Remove the quirk SDHCI_QUIRK_NO_CD as it is not required. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynqmp: Add support for R5 sw loadingMichal Simek2015-04-29-3/+285
| | | | | | | | | | | | | | Add support for loading sw for R5 with enabling for zynqmp. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
| * zynqmp: caches: Enable dcache for zynqmpSiva Durga Prasad Paladugu2015-04-29-1/+165
| | | | | | | | | | | | | | | | Define the mmu table till 2MB granularity enable dcaches for zynqmp. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynq: slcr: Disable all level shiftersSiva Durga Prasad Paladugu2015-04-29-0/+7
| | | | | | | | | | | | | | | | | | | | | | Disable all level shifters before enabling the PS-to-PL level shifters as it would be good to disable all level shifters before enabling the PS-to-PL in order to ensure that it is in proper state Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: zynq: drop legacy ps7_init.c/h supportMasahiro Yamada2015-04-29-7/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | We are about to change the location for ps7_init files, breaking the current work-flows. It is good time to drop the legacy ps7_init.c/h support. Going forward, please use ps7_init_gpl.c/h all the time. If you are still using old Xilinx tools that are only able to generate ps7_init.c/h, rename them into ps7_init_gpl.c/h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynq: Add Zynq PicoZed board supportNathan Rossi2015-04-29-0/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PicoZed is a System-on-Module board which is marketed as part of the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000 processor. This patch adds support that covers all the variants of the PicoZed including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This patch set however only covers support for the System-on-Module and does not cover any extra components that are available on carrier boards (except those that are fanned out of the module itself). More information on this board, its variants and available carrier boards is available at: http://zedboard.org/product/picozed Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * serial: zynq: Add support for slow emulation platformMichal Simek2015-04-29-1/+7
| | | | | | | | | | | | | | | | On slow platforms not all baudrate setting is valid. Check it directly in the driver and setup maximum possible frequency. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * zynq: Enable GPIO driver and GPIO commandsMichal Simek2015-04-29-0/+3
| | | | | | | | | | | | Enable GPIO driver and GPIO commands. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * gpio: add Xilinx Zynq PS GPIO driverAndrea Scian2015-04-29-0/+287
| | | | | | | | | | | | | | | | | | Most of the code is taken (and adapted) from Linux kernel driver. Just add CONFIG_ZYNQ_GPIO to you config to enable it Signed-off-by: Andrea Scian <andrea.scian@dave.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2015-04-29-1/+1
|\ \
| * | microblaze: Fix EMAC Lite initializationNathan Rossi2015-04-29-1/+1
| |/ | | | | | | | | | | | | | | | | | | It is possible for CONFIG_XILINX_EMACLITE to be defined without XILINX_EMACLITE_BASEADDR being defined as the EMAC Lite driver support OF init. Check that the driver is enabled and the base address is available before initializing with a static base address. Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-socfpgaTom Rini2015-04-28-51/+197
|\ \
| * | socfpga: implement arria V socdk SPI flash config in dtsPavel Machek2015-04-27-0/+24
| | | | | | | | | | | | | | | | | | | | | Arria V SocDK has same QSPI and SPI flash configuration as Socrates. Add support for it. Signed-off-by: Pavel Machek <pavel@denx.de>
| * | socfpga: implement socdk SPI flash config in dtsPavel Machek2015-04-24-0/+24
| | | | | | | | | | | | | | | | | | | | | SocDK has same QSPI and SPI flash configuration as Socrates. Add support for it. Signed-off-by: Pavel Machek <pavel@denx.de>
| * | arm: socfpga: spl: Add stub sdram.hMarek Vasut2015-04-21-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the SoCFPGA SDRAM support is not yet applied to u-boot, we still need to be able to compile the codebase. Introduce stub functions which temporarily supplement the missing SDRAM setup functions. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@opensource.altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Pavel Machek <pavel@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Vince Bridgers <vbridger@opensource.altera.com>
| * | spi: Add Cadence QSPI controller Kconfig entryMarek Vasut2015-04-21-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Cadence QSPI controller Kconfig entry. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@opensource.altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Acked-by: Pavel Machek <pavel@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Vince Bridgers <vbridger@opensource.altera.com>
| * | spi: Add Designware SPI controller Kconfig entryMarek Vasut2015-04-21-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DWC SPI controller Kconfig entry. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@opensource.altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Acked-by: Pavel Machek <pavel@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Vince Bridgers <vbridger@opensource.altera.com>
| * | arm: socfpga: spl: update peripheral pll for dev kitDinh Nguyen2015-04-21-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | "commit 0d13a0051b2c arm: socfpga: Sync Cyclone V DK PLL configuration" mistakenly changed CONFIG_HPS_MAINPLLGRP_VCO_NUMER to 39, the correct value should be 79. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: add board_init_f to SPLDinh Nguyen2015-04-21-0/+29
| | | | | | | | | | | | | | | | | | | | | Remap SDRAM to 0x0, and clear OCRAM's ECC in board_init_f(). Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Reviewed-by: Marek Vasut <marex@denx.de>
| * | arm: socfpga: spl: Add s_init stubDinh Nguyen2015-04-21-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a stub s_init function in the board file. The reason why the stub function is needed is that most of the work is now being done in board_init_f(), there is no need for the SPL to do anything s_init(). However, since lowlevel_init() is still branching to s_init(), we need stub function for now, until lowlevel_init() morphs into s_init(). Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: fix uart0 pin mux configurationDinh Nguyen2015-04-21-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit "07d30b6c3129 arm: socfpga: Sync Cyclone V DK pinmux configuration" incorrectly set the muxing for UART0 on the Cyclone V DK. This fixes it up so UART0 is working again. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: Add SDRAM checkDinh Nguyen2015-04-21-0/+6
| | | | | | | | | | | | Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: Adjust the SYS_INIT_RAM_SIZE to have room for the spl mallocDinh Nguyen2015-04-21-1/+1
| | | | | | | | | | | | | | | | | | | | | We need to adjust the SYS_INIT_RAM_SIZE to have room for the SPL_MALLOC_SIZE. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: add CONFIG_SPL_STACK to socfpga_common.hDinh Nguyen2015-04-21-0/+5
| | | | | | | | | | | | Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: Use common lowlevel_initDinh Nguyen2015-04-21-47/+1
| | | | | | | | | | | | | | | | | | | | | For SoCFGPA, use the common ARMv7 lowlevel_init. Thus, we can delete the SoCFPGA lowlevel_init.S file. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: printout sdram sizeDinh Nguyen2015-04-21-0/+4
| | | | | | | | | | | | | | | Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Reviewed-by: Marek Vasut <marex@denx.de>
| * | arm: socfpga: spl: add sdram init and calibrationDinh Nguyen2015-04-21-0/+13
| | | | | | | | | | | | | | | | | | Add a call to checkboard along with sdram intilialization and calibration. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: allow bootrom to enable IOs after warm resetDinh Nguyen2015-04-21-0/+13
| | | | | | | | | | | | | | | Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Marek Vasut <marex@denx.de>
| * | arm: socfpga: spl: Add call to timer_initDinh Nguyen2015-04-21-0/+2
| | | | | | | | | | | | Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
| * | arm: socfpga: spl: enable sdram, timer and uartDinh Nguyen2015-04-21-0/+4
| | | | | | | | | | | | | | | | | | | | | Add the calls in the spl_board_init to enable SDRAM, timer, and UART. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Marek Vasut <marex@denx.de>
| * | arm: socfpga: add functions to bring sdram, timer, and uart out of resetDinh Nguyen2015-04-21-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | These functions will be needed for use by the SPL for enabling the console and sdram initialization. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Pavel Machek <pavel@denx.de>
generated by cgit v1.1 at 2024-07-04 20:38:45 +0000