summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* powerpc/p1010rdb: fix calculating ddr_freq_mhzShengzhou Liu2013-08-20-1/+1
| | | | | | | | There was a bug for calculating ddr_freq_mhz, it should be divided by 1000000 rather than 0x1000000. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/t4240: add QSGMII interface supportShaohui Xie2013-08-20-31/+108
| | | | | | | | | | Also some fix for QSGMII. 1. fix QSGMII configure of Serdes2. 2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN. 3. fix dtb for QSGMII interface. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/t4240: fix lanes routing for QSGMII protocolsShaohui Xie2013-08-20-2/+37
| | | | | | | | When using QSGMII protocols, the first lane and third lane on each slot need to be swapped. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/common/vsc3316: remove const from vsc3316_config parameter defineShaohui Xie2013-08-20-12/+12
| | | | | | | | | Since the parameters need to be modified according to different Serdes protocols at runtime, the const will block this. Also remove const from arrays define used by vsc3316_config. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpcv2: Print hardcoded size like print_size() doesShruti Kanetkar2013-08-20-21/+21
| | | | | | | | | Makes the startup output more consistent Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com>
* powerpc: Use print_size() where appropriateShruti Kanetkar2013-08-20-22/+21
| | | | | | | | Makes the startup output more consistent Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* SPDX-License-Identifier: clean up license headerYork Sun2013-08-20-48/+3
| | | | | | | | | This patch cleans up license header in these files: board/freescale/p1022ds/spl.c drivers/mmc/fsl_esdhc_spl.c drivers/mtd/spi/fsl_espi_spl.c Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc: Fix CamelCase checkpatch warningsPrabhakar Kushwaha2013-08-20-146/+149
| | | | | | | | | | | 85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions. because of this code checkpatch script generates "WARNING: Avoid CamelCase". Convert variables name to normal naming convention and modify board, driver files with updated the new structure. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc: p1022ds: add TPL for p1022ds nand bootYing Zhang2013-08-20-71/+103
| | | | | | | | TPL is introduced in the patch "NAND: TPL : introduce the TPL based on the SPL", here enable TPL for p1022ds nand boot. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* TPL : introduce the TPL based on the SPLYing Zhang2013-08-20-14/+147
| | | | | | | | | | | | | | | | Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can not be more than 4K. So, the SPL cannot initialize the DDR with the SPD code. This patch introduces TPL to enable a loader stub that is loaded by the code from the SPL. It initializes the DDR with the SPD or other operations. The TPL's size is sizeable, the maximum size is decided by the memory's size that TPL runs. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are three stage uboot images: * spl_boot, * tpl_boot, * final uboot image Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc : p1022ds : Enable p1022ds to start from eSPI with SPLYing Zhang2013-08-20-7/+39
| | | | | | | Enable p1022ds to start from eSPI with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc : spi flash : Support to start from eSPI with SPLYing Zhang2013-08-20-0/+80
| | | | | | | | | | | | | | | | | This patch introduces SPL to enable a loader stub that being loaded by the code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPLYing Zhang2013-08-20-17/+179
| | | | | | | Enable p1022ds to start from eSDHC with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc: mpc85xx: Support booting from SD Card with SPLYing Zhang2013-08-20-0/+233
| | | | | | | | | | | | | | | | The code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some ↵Ying Zhang2013-08-20-6/+6
| | | | | | | | | | | functionality for common SPL 1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it. 2. Some functions were unused in the minimal SPL, but it is useful in the common SPL. So, enabled some functionality for common SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* spl: env_common.c: make CONFIG_SPL_BUILD contain function env_importYing Zhang2013-08-20-2/+0
| | | | | | | | | | The functionality env_import will be used in the SPL. They had been excluded by ifndef CONFIG_SPL_BUILD. Now, put it into the SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: York Sun <yorksun@freescale.com>
* SPL: Makefile: Build a separate autoconf.mk for SPLJoel Fernandes2013-08-19-2/+24
| | | | | | | | | | | | | | | | | | | | | SPL defines CONFIG_SPL_BUILD but this does not percolate to the autoconf.mk Makefile. As a result the build breaks when CONFIG_SPL_BUILD is used in the board-specific include header file. With this, there is a possibility of having a CONFIG option defined in the header file but not defined in the Makefile causing all kinds of build failure and problems. It also messes things for up, for example, when one might want to undefine options to keep the SPL small and doesn't want to be stuck with the CONFIG options used for U-boot. Lastly, this also avoids defining special CONFIG_SPL_ variables for cases where some options are required in U-boot but not in SPL. We add a spl-autoconf.mk rule that is generated for SPL with the CONFIG_SPL_BUILD flag and conditionally include it for SPL builds. Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Ying Zhang <b40530@freescale.com>
* Prepare v2013.10-rc1Tom Rini2013-08-19-2/+2
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* SPDX-License-Identifier: convert BSD-3-Clause filesWolfgang Denk2013-08-19-3796/+179
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini Don't remove some copyrights by accident] Signed-off-by: Tom Rini <trini@ti.com>
* board/esd/cpci750/mv_eth.c: Fix licenseWolfgang Denk2013-08-19-16/+1
| | | | | | | | | | | The file header indicated that this file was GPL-2.0+, but actually the code was derived from (Marvell based) Linux source code which is only GPL-2.0. Fix this. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Acked-by: Stefan Roese <sr@denx.de>
* SPDX-License-Identifier: convert PIBS licensed filesWolfgang Denk2013-08-19-528/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adapts the files that were derived from PIBS (PowerPC Initialization and Boot Software) codeto using SPDX License Identifiers. So far, SPDX has not assigned an official License ID for the PIBS license yet, so this should be considered preliminary. Note that the following files contained incorrect license information: arch/powerpc/cpu/ppc4xx/4xx_uart.c arch/powerpc/cpu/ppc4xx/start.S arch/powerpc/include/asm/ppc440.h These files included, in addition to the GPL-2.0 / ibm-pibs dual license as inherited from PIBS, a GPL-2.0+ license header which was obviously incorrect. This has been removed. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Conflicts: Licenses/README Acked-by: Stefan Roese <sr@denx.de>
* SPDX-License-Identifier: fixing some problematic GPL-2.0 filesWolfgang Denk2013-08-19-90/+5
| | | | | | | | | | | | | | | | | Unlike the other patches in this series so far, this commit fixes a ambiguity in the license terms for some OMAP files: the code was originally derived from the Linux kernel sources, where it was clearly marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot version had a GPL-2.0+ file header added, apparently without permission / relicensing from the original authors of the code. Insert a GPL-2.0 SPDX-License-Identifier to fix this. Signed-off-by: Wolfgang Denk <wd@denx.de> cc: Tom Rix <Tom.Rix@windriver.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com>
* SPDX-License-Identifier: convert GPL-2.0+ / BSD-2-Clause dual-licensed filesWolfgang Denk2013-08-19-44/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* net: ftmac110: Update tx/rx descriptor formatKuo-Jung Su2013-08-19-74/+82
| | | | | | | | 1. Reformat tx/rx descriptor as an uniform struct. 2. Replace uint32_t[2] with uint64_t for descriptor control. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Joe Hershberger <joe.hershberger@gmail.com>
* net: ftmac110: struct ftmac110_regs __iomem * -> struct ftmac110_regs *Kuo-Jung Su2013-08-19-5/+5
| | | | | Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Joe Hershberger <joe.hershberger@gmail.com>
* net: ftmac110: Update license statementKuo-Jung Su2013-08-19-2/+2
| | | | | Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Joe Hershberger <joe.hershberger@gmail.com>
* net.h: don't use the reserved name __unusedJeroen Hofstee2013-08-19-1/+1
| | | | | | | | | The __* keywords are reserved. On FreeBSD __unused evaluates to the attribute unused, causing a compilation failure. Just use unused instead. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> cc: joe.hershberger@gmail.com
* linkstation_HGLAN: Convert from unused CONFIG_BOOTP_MASK to specific listTom Rini2013-08-19-1/+11
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* galaxy5200: Convert from unused CONFIG_BOOTP_MASK to specific listTom Rini2013-08-19-4/+3
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* configs: Remove unused CONFIG_BOOTP_DEFAULTTom Rini2013-08-19-18/+0
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* net: phy/realtek: Add support for RTL8211DN and RTL8211E phy modulesBhupesh Sharma2013-08-19-26/+51
| | | | | | | | | | | | This patch adds support for Realtek PHY modules RTL8211DN and RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG), which can be found on Freescale's T1040RDB boards. To make the driver more generic across 8211 family, a generic name 8211x is added for macros and function names. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* net: smsc95xx: Add support for another SMSC95xx variantStefan Roese2013-08-19-0/+1
| | | | | | | | | This patch adds support for the SMSC9500 with product id 0x9900 which is equipped in the "EXSYS USB 2.0" etherner USB adapter. Tested on omap3_beagle. Signed-off-by: Stefan Roese <sr@denx.de>
* net: Use ARRAY_SIZE at appropriate placesAxel Lin2013-08-19-17/+10
| | | | | | | | | | | | | | | | | | Use ARRAY_SIZE instead of having similar implementation in each drivers. The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used at all, so this patch removes it instead of converting it to use ARRAY_SIZE. Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Marek Vasut <marex@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: York Sun <yorksun@freescale.com>
* phy: smsc: LAN8710/8720 are not Gbit PHYsFabio Estevam2013-08-19-1/+1
| | | | | | | | LAN8710/8720 are 10/100 Mbps PHYs, so fix the '.features' field. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* serial: arm_dcc: Convert to use default_serial_putsAxel Lin2013-08-19-7/+1
| | | | | | | | Use default_serial_puts() instead of its own implementation. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Michal Simek <monstr@monstr.eu>
* powerpc/ppc4xx: Fix dlvision-10g reset gpioDirk Eibach2013-08-19-2/+2
| | | | | Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
* powerpc/ppc4xx: Do full iocon PHY initialization in softwareDirk Eibach2013-08-19-48/+172
| | | | | | | | | | | Up to this point some PHY initialization was done from the FPGA and some from u-boot. From now all initialization is done from u-boot. To keep this maintainable a PHY setup machine was implemented that can execute commands from initialization arrays. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
* powerpc/ppc4xx: Add support for iocon-2Dirk Eibach2013-08-19-11/+25
| | | | | | | Add a new iocon flavor with a second communiction port per channel. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
* powerpc/ppc4xx: Add support for iocon fiberDirk Eibach2013-08-19-8/+36
| | | | | | | Add a new iocon flavor with fiber instead of copper connectivity. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'master' of git://88.191.163.10/u-boot-armTom Rini2013-08-18-3544/+6620
|\ | | | | | | | | | | | | | | | | | | Fixup an easy conflict over adding the clk_get prototype and USB_OTG defines for am33xx having moved. Conflicts: arch/arm/include/asm/arch-am33xx/hardware.h Signed-off-by: Tom Rini <trini@ti.com>
| * Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-08-17-1966/+601
| |\
| | * Merge git://git.denx.de/u-boot-armStefano Babic2013-07-31-95031/+13229
| | |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: board/freescale/mx6qsabrelite/Makefile board/freescale/mx6qsabrelite/mx6qsabrelite.c include/configs/mx6qsabrelite.h Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * | mxc_ipuv3: fix memory alignment of framebufferEric Nelson2013-07-29-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | The frame-buffer on i.MX boards needs to be aligned for DMA. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| | * | imx: nitrogen6x: mx6qsabrelite: Add support for DVI monitorsRobert Winkler2013-07-27-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A little background is probably appropriate for this patch. Since "the beginning" of usage of the SABRE Lite and Nitrogen6x boards, DVI detection has been somewhat broken. Some (most) DVI monitors don't produce the "HPD" bit in the PHY_STAT0 register, but do show proper toggling of the RX_SENSE0..3 bits. Creating a new the bit-mask to include all five bits and modifying the 'hdmidet' command and internal detection routines allows these monitors to function properly in U-Boot. A related patch to our kernels allows things to work under Linux: https://github.com/boundarydevices/linux-imx6/commit/7d8752905c118af9063738a533227de0b2f6ecd4 Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | imx: Add documentation for imx specific commandsRobert Winkler2013-07-27-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_CMD_HDMIDETECT CONFIG_CMD_BMODE Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| | * | mx6qsabresd: Add splash screen support via HDMIPardeep Kumar Singla2013-07-27-2/+84
| | | | | | | | | | | | | | | | Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
| | * | mx6: Factor out common HDMI setup codePardeep Kumar Singla2013-07-27-78/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of duplicating HDMI setup code for every mx6 board, factor out the common code Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com> Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
| | * | mx6qsabrelite: Remove mx6qsabrelite code in favor of nitrogen6xFabio Estevam2013-07-26-1189/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the code duplication and only use the nitrogen6x source code to make board code maintainance easier. Tested booting a mainline device tree kernel on a mx6qsabrelite board. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * | wandboard: Use splash image at screen center by defaultOtavio Salvador2013-07-24-0/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * | mxc_gpio: Correct the GPIO handling in gpio_direction_output()Dirk Behme2013-07-24-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Setting the direction and an output value should be done by First, set the desired output value. Then, switch to output. If this is done in the inverse order, like at the moment, there can be a glitch on the GPIO line while switching first the old output value and aftwards the new one. Fix this by inverting the order of the direction/set_value calls. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-09-19 21:13:20 +0000