summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* zynq: Add support for U-BOOT SPLMichal Simek2014-02-19-2/+241
| | | | | | | | | | | | | | | | | SPL is using ps7_init.c/h files which are generated from design tools which have to be copied to boards/xilinx/zynq folder before compilation. BSS section is moved to SDRAM because fat support requires more space than SRAM size. Added: - MMC and QSPI support - Boot OS directly from SPL - Enable SPL command Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* zynq: Update CLK in bdinfoMichal Simek2014-02-19-0/+5
| | | | | | ARM has specific clk entries which should be also setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Implement dump clock commandSoren Brinkmann2014-02-19-0/+22
| | | | | | | | Enable and implement dump clock command which shows soc frequencies. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* serial_zynq: Migrate to Zynq clock frameworkSoren Brinkmann2014-02-19-11/+2
| | | | | | | | Remove hard coded frequencies and use Zynq's clock framework to obtain the UART clock frequency. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* net: zynq_gem: Calculate clock dividers dynamicallySoren Brinkmann2014-02-19-12/+20
| | | | | | | | Remove hard coded clock divider setting and use the Zynq clock framework to dynamically calculate appropriate dividers at run time. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* net: zynq_gem: Move RCLK details out of driverSoren Brinkmann2014-02-19-9/+6
| | | | | | | | | The GEM driver should not need to know about Zynq specific details of RCLK related registers and bitfields in the SLCR. Move those details to the slcr driver. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: timer: Fix hangs if network activity attempted after about one hourMichal Simek2014-02-19-2/+2
| | | | | | | | | | | | Cortex-A9 MPCore TRM' from ARM (ARM DDI 0407G ID072711) describes in the section 4.1.1 how this value calculation should be done. This patch fixes the problem if network activity such as ping or tftp is attempted after u-boot has been idle for an hour, it hangs, and cannot control-C out of it. Signed-off-by: Uday Hegde <udayh@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: timer: Migrate to zynq clock frameworkSoren Brinkmann2014-02-19-4/+7
| | | | | | | Remove hardcoded frequencies in favor of Zynq clock framework. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Provide a framework to read clock frequenciesSoren Brinkmann2014-02-19-2/+701
| | | | | Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* common: Provide DIV_ROUND_CLOSEST macroSoren Brinkmann2014-02-19-0/+16
| | | | | | | | Provide the DIV_ROUND_CLOSEST macro - taken from the Linux kernel - in common.h Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: serial: Simplify serial driver initializationMichal Simek2014-02-19-31/+24
| | | | | | | | | | Define both serial uarts in the driver and return default uart based on board configuration. - Move baseaddresses to hardware.h - Define default baudrate and clock values Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Move bootmode to headersMichal Simek2014-02-19-6/+6
| | | | | | These numbers will be reused by SPL. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Use board_eth_init if CMD_NET is not enabledMichal Simek2014-02-19-2/+0
| | | | | | | board_eth_init can be also called in cases where CMD_NET is not enabled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Enable tftp put commandMichal Simek2014-02-19-0/+1
| | | | | | For saving content of memory via tftp to file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Extend kernel image size to 20MBMichal Simek2014-02-19-0/+3
| | | | | | | | | | | Extend max kernel image size. Gunzip is checking this value. If kernel is larger, message below is shown. Uncompressing Kernel Image ... Error: inflate() returned -5 GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Fix incorrect header nameMichal Simek2014-02-19-2/+2
| | | | | | | Zynq common configuration is placed in zynq-common.h not zynq_common.h. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Enable dcache supportMichal Simek2014-02-19-0/+8
| | | | | | Enable dcache. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: Do not explicitely enable icacheMichal Simek2014-02-19-2/+0
| | | | | | icache is already enabled by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'Albert ARIBAUD2014-02-19-70403/+5
|\
| * ARM: serial: Remove the IXP UART driverMarek Vasut2014-02-06-137/+0
| | | | | | | | | | | | | | | | | | This driver is no longer used, remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: NET: Remove the IXP NPE ethernet driverMarek Vasut2014-02-06-65939/+0
| | | | | | | | | | | | | | | | | | This driver is no longer used, remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: PCI: Remove the IXP PCI driverMarek Vasut2014-02-06-356/+0
| | | | | | | | | | | | | | | | | | The driver is no longer used, remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: USB: Remove the IXP EHCI driverMarek Vasut2014-02-06-38/+0
| | | | | | | | | | | | | | | | | | The driver is no longer used, remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: IXP: Remove the IXP architecture supportMarek Vasut2014-02-06-1547/+0
| | | | | | | | | | | | | | | | | | The architecture is unmaintained and dead, remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: IXP: Remove dvl_host boardMarek Vasut2014-02-06-500/+1
| | | | | | | | | | | | | | | | | | The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: IXP: Remove actux4 boardMarek Vasut2014-02-06-375/+1
| | | | | | | | | | | | | | | | | | The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: IXP: Remove actux3 boardMarek Vasut2014-02-06-506/+1
| | | | | | | | | | | | | | | | | | The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: IXP: Remove actux2 boardMarek Vasut2014-02-06-479/+1
| | | | | | | | | | | | | | | | | | The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
| * ARM: IXP: Remove actux1 boardMarek Vasut2014-02-06-526/+1
| | | | | | | | | | | | | | | | | | The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-17-6851/+17596
|\ \
| * | ARM: bcm2835: fix mbox POWER_STATE_RESP_ON valueStephen Warren2014-02-14-1/+1
| | | | | | | | | | | | | | | | | | Typo: The correct value is 1 not 2. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
| * | arm/km: introduce kmsugp1 targetGerlando Falauto2014-02-13-2/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA. The only difference is that the PCIe reset is connected to Kirkwood pin MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7. Such pin should theoretically be handled by the PCIe subsystem automatically, but this turned out not to be the case. So simply configure this PIN as a GPIO and issue a pulse manually. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com> Cc: Valentin Longchamp <valenting.longchamp@keymile.com> Cc: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km: define fdt_high env variable and allow backwards compatibilityGerlando Falauto2014-02-13-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high" This is necessary on Kirkwood so that the FDT does not get relocated above the memory limit that the kernel cannot access (that is the memory part reserved for the switch). This was tested on NUSA1, where it is necessary, and on ETER1, where it doesn't seem to hurt. We want the scripts to also work with older versions of u-boot, where: a) set_fdthigh is not defined (will be default env for newer u-boots) b) the fdt will not be available For this reason, we use "set_fdthigh" to tell whether we are running a newer (FDT-aware) u-boot or not. So if "set_fdthigh" runs successfully or arch != arm we try loading the fdt; otherwise we proceed normally. Notice how, contrary to release mode, set_fdthigh will _not_ be part of subbootcmds for develop and ramfs, but will be executed as part of "tftpfdt". Since this is only needed for kirkwood cards, and it prevents the kernel from booting on QorIQ (though it seemed to work on ETER1), we change its definition in the default env for powerpc so that the value is only set on ARM. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km: enable FDT for km_kirwkoodGerlando Falauto2014-02-13-14/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This consists of: a) Defining the addresses, enabling fdtsupport [arm] b) Defining "cramfsloadfdt" [arm,powerpc => common] c) Adding the FDT address to bootm [arm,powerpc => common] d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common] This should work with 3.10 kernels, whether loaded through TFTP (with rootfs either through NFS or TFTP-ramfs) or from the NAND. The machid was left unchanged, this should keep compatibility with both older and newer kernels. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km: fix wrong error handlingHolger Brunck2014-02-13-5/+5
| | | | | | | | | | | | | | | | | | | | | miiphy_read and miiphy_write are returning 0 on success. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km: add CONFIG_KM_BOARD_EXTRA_ENV to default environmentHolger Brunck2014-02-13-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | This is needed for board specific additional environment variables. E.g. the mgcoge3un has this additional "waitforne" variable. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km/suv31: switch to 256MB RAMHolger Brunck2014-02-13-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | We now use 256MB RAM instead of 128MB. We can use the same config file as kmnusa. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km: make local function startup_allowed staticHolger Brunck2014-02-13-1/+1
| | | | | | | | | | | | | | | Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | arm/km: drop unneeded defineHolger Brunck2014-02-13-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | CONFIG_BOOTCOUNT_LIMIT is used on all boards from this board series. So remove this unneeded define. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
| * | zynq: Fix elf header generationMichal Simek2014-02-13-0/+101
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is here because of: "arm: keep all sections in ELF file" (sha1: 47ed5dd031d7d2c587e6afd386e79ccec1a1b7f7) Our tools expect to have elf with only LOAD header. Without this fix also PHDR, INTERP and DYNAMIC headers are available in ELF. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | zynq: Use full tftpboot command instead of shortcut tftpMichal Simek2014-02-13-1/+1
| | | | | | | | | | | | | | | | | | | | | The reason is enabling tftpput command where tftp shorcut stops to work for tftpboot. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | relocate-rela: replace a magic number with sizeof(Elf64_Rela)Masahiro Yamada2014-02-13-1/+1
| | | | | | | | | | | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Scott Wood <scottwood@freescale.com> Cc: David Feng <fenghua@phytium.com.cn> Acked-by: Scott Wood <scottwood@freescale.com>
| * | ARM: bcm2835: config.mk isn't neededStephen Warren2014-02-13-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The entries in config.mk were needed so that U-Boot could be built with an old version of the Raspberry Pi Foundation's toolchain. Without them, the build would error out with: ...-ld: error: .../libgcc.a(_bswapsi2.o) uses VFP register arguments, u-boot does not However, none of the 3 toolchains in the latest version of their tools.git, nor the Ubuntu/Linaro ARM compilers in at least Ubuntu Quantal or Saucy, need these options set in order to compile a working U-Boot. Hence, remove the options for simplicity. Reported-by: Tom Rini <trini@ti.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Andreas Färber <afaerber@suse.de>
| * | ARM: rpi_b: set $fdtfile in default environmentStephen Warren2014-02-13-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | U-Boot names the Raspberry Pi board rpi_b. This means that the common expression for DTB filename ${soc}-${board}.dtb expands to bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts look for the correct DTB filename. An alternative would be to rename the U-Boot board to rpi-b. However, that change would be far more invasive, and end up affecting users (i.e they'd have to change their U-Boot build commands). Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
| * | Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2014-02-13-5458/+11605
| |\ \
| | * | exynos: clock: use the clear and set bits macros.Inha Song2014-02-10-65/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use setbits/clrbits macro instead of readl/writel function. (Suggested by Wolfgang) Signed-off-by: Inha Song <ideal.song@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| | * | exynos: clock: fixed that cfg is set to wrong value.Inha Song2014-02-10-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixed that cfg value is set to wrong value. Because it didn't read the related register. Signed-off-by: Inha Song <ideal.song@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| | * | board:samsung:trats/trats2: enable boot with appended and separated DTBPiotr Wilczek2014-02-07-6/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch modifies envs to enable dual kernel boot - with separated DTB if the DTB file is loaded successfully; - with DTB apppended to uImage if DTB file is not found; This is neccesssary for backward compatibilty. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| | * | board:samsung:trats2: add env variables describing platformPiotr Wilczek2014-02-07-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds variables describing platform (soc, board, vendor) to default environment. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| | * | board:samsung:trats: add env variables describing platformPiotr Wilczek2014-02-07-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds variables describing platform (soc, board, vendor) to default environment. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit v1.1 at 2024-09-18 21:24:31 +0000