summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* MLK-14915 mx6ul_arm2/mx6ull_arm2: Fix ENET PHY reset issueYe Li2017-05-15-27/+59
| | | | | | | | | There are two pins used for ENET PHY reset, need to assert them before init the PHY. Current DM driver does not have such operation, need board level codes to handle. This patch moves the PHY reset operation into setup_fec, which is common for DM driver and non-DM driver. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14890 i2c: Enable I2C force idle busYe Li2017-05-15-91/+648
| | | | | | | | | | | This patch enables the I2C force idle bus for all i.MX6 and i.MX7 boards to avoid i2c bus problem during reboot. To use it, we must add some i2c properties in DTB file and the GPIO pinctrl for i2c. For mx6qsabreauto, mx6slevk, mx6sxsabresd and mx6sxscm, these boards call the setup_i2c. To remove conflict, change to use "setup_i2c" only for non-DM i2c driver. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14891 mx6slevk/mx6sll_arm2: Fix SPINOR CS GPIO usingYe Li2017-05-14-0/+4
| | | | | | | Needs to request the GPIO pin before assigning to GPIO to SPI driver which will directly setting it to output without request it. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14772 net: fec: set the device->seq id to priv->dev_idFugang Duan2017-05-12-5/+3
| | | | | | | | | i.MX6UL/ULL evk board net get the wrong MAC address from fuse, exp, eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the priv->dev_id to device->seq as the real net interface alias id then .fec_get_hwaddr() read the related MAC address from fuse. Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
* MLK-14877 DTB: mx6sllevk: Fix usdhc2 property issueYe Li2017-05-11-1/+1
| | | | | | | | For eMMC, should using "non-removable" property, not "no-removable", this cause USDHC driver has problem in get_cd, then switching to eMMC will always show no card present. Signed-off-by: Ye Li <ye.li@nxp.com>
* ARM: fixed relocation using proper alignmentManfred Schlaegl2017-05-11-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Using u-boot-2017.05 on i.MX6UL we ran into following problem: Initially U-Boot could be started normally. If we added one random command in configuration, the newly generated image hung at startup (last output was DRAM: 256 MiB). We tracked this down to a data abort within relocation (relocated_code). relocated_code in arch/arm/lib/relocate.S copies 8 bytes per loop iteration until the source pointer is equal to __image_copy_end. In a good case __image_copy_end was aligned to 8 bytes, so the loop stopped as suggested, but in an errornous case __image_copy_end was not aligned to 8 bytes, so the loop ran out of bounds and caused a data abort exception. This patches solves the issue by aligning __image_copy_end to 8 byte using the linker script related to arm. From Community: http://patchwork.ozlabs.org/patch/760592/ Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14864: regulator: pfuze100: unsigned compared against 0Peng Fan2017-05-11-3/+9
| | | | | | Fix coverity:392391 392382 392385 Unsigned compared against 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14862 net: eth-uclass: add return value checkPeng Fan2017-05-11-2/+12
| | | | | | | | Add return value check Coverity 392391 Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14840: pinctrl: imx: fix resource leakPeng Fan2017-05-11-0/+5
| | | | | | | | | The device managed API actually not free the memory, so need to use devm_kfree to free the memory to avoid leakage. Coverity: 392384 resource leak Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14878 qspi: Fix issue when enabling DDR modeYe Li2017-05-10-7/+13
| | | | | | | | | | | | | | | There are two problems in enabling DDR mode in this new driver: 1. The TDH bits in FLSHCR register should be set to 1. Otherwise, the TX DDR delay logic won't be enabled. Since u-boot driver does not have DDR commands in LUT. So this won't cause explicit problem. 2. When doing read/write/readid/erase operations, the MCR register is overwritten, the bits like DDR_EN are cleared during these operations. When we using DDR mode QSPI boot, the TDH bit is set to 1 by ROM. if the DDR_EN is cleared, there is no clk2x output for TX data shift. So these operations will fail. The explicit problem is users may get "SF: unrecognized JEDEC id bytes: ff, ff, ff" error after using DDR mode QSPI boot on 6UL/ULL EVK boards. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14808 mx6sxsabresd: Fix wrong configuration name for QSPI bootYe Li2017-05-10-1/+1
| | | | | | | A wrong config name is used for QSPI boot, it causes IVT offset wrong. Fix the typo issue. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14792 mx6ull: Disable WDOG3 after initYe Li2017-05-10-1/+1
| | | | | | | Need to power down WDOG3 for mx6ull, otherwise the kernel will reboot once the iomux for WDOG_ANY pin is configured. This is missed in community u-boot. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14839-2 imx: clean up print info for thermal and reset causeYe Li2017-05-09-3/+4
| | | | | | | Clean up the print info, so that the reset cause print can display in a new line. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14839-1 mx6: Fix wrong CPU frequencyYe Li2017-05-09-1/+1
| | | | | | Fix incorrect value for 696MHz CPU frequency on i.MX6UL. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14845 mx6/mx7: Not call usb setup functions used by non-DM driverYe Li2017-05-09-1/+101
| | | | | | | | | | | Use CONFIG_DM_USB to comment out USB setup functions used by non-DM driver. So they won't be executed when using DM driver. These USB setup functions may setup power control pins to USB_PWR function not GPIO, which is different as the GPIO function used by USB vbus-supply. And cause the power control not work. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14775 mx7dsabresd: Disable USDHC2 in device treeYe Li2017-05-08-1/+1
| | | | | | | | | | | The USDHC2 is connecting to BT/WIFI chip on SDB board, this controller is enabled in device tree as SDIO, but USDHC driver in u-boot will use it as SDHC. So totally 3 USDHC devices will be created, and cause run time MMC environments go wrong because it only supports USDHC1 and USDHC3. So disable the unused USDHC2 controller in u-boot device tree. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14828 env_sata: Fix SATA saveenv issueYe Li2017-05-08-1/+1
| | | | | | | Wrong env buffer was passed into sata write function, so the saveenv can't work. Fix this issue. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14768 fec: Change CONFIG_ETHPRIME name to align with DM ETHYe Li2017-05-08-0/+92
| | | | | | | | | | The DM Ethernet driver requests the "ethprime" to align with DTB name or start with "eth" with seq number as index. So previous name "FEC" can't work as prime. Must change it to the "eth0" for first ethernet device, or "eth1" for second one. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14831 mx6: Fix wrong bmode value used for usb bootYe Li2017-05-08-1/+1
| | | | | | | Wrong bmode value is used in community u-boot for usb reboot. And cause it failed. Fix this by using a reserved bootcfg value. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14779 mx6qdlsabreauto: Fix usb detect issueYe Li2017-05-08-26/+6
| | | | | | | | The recent ehci-mx6 driver can support vbus-supply property, no need to request io expander pins in usb setup. If did this, the regulator for vbus-supply will fail to get due to the pin is occupied. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14777 imx: mx6ul/mx6ull/mx7d: correct the usage of the macro ↵Fugang Duan2017-05-04-14/+14
| | | | | | | | | | | | | PFUZE3000_SW1AB_SETP() Commit:894a4b4da7e2 add the voltage configuration macro that base on the 0.1mV precision, and i.MX6UL/i.MX6ULL/i.MX7D use the macro as 1mV prevision that cause the conversion are wrong, then some boards cannot boot up in ldo bypass mode. The patch just correct the usage of PFUZE3000_SW1AB_SETP(). Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
* MLK-14776 imx6sl: add enet phy reset to i.MX6SL EVK boardFugang Duan2017-05-03-7/+8
| | | | | | | | For some i.MX6SL evk board, enet phy need reset. Add phy reset before phy clock enable and init the pinctrl earlier. Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
* MXSCM-292-3 mx6sxscm: add dts files for EVB boardJuan Gutierrez2017-04-28-1/+1185
| | | | | | | Copy the dts files from kernel for MX6SXSCM EVB board for preparing enabling the OF_CONTROL. Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-292-2 mx6sxscm: convert to enable OF_CONTROL and DM driversJuan Gutierrez2017-04-28-31/+391
| | | | | | | | | | | | | Update mx6sxscm boards code and build configurations to enable OF_CONTROL and DM drivers. 1. Update GPIO codes for adding gpio request 2. Update PMIC and LDO by-pass codes for DM PMIC 3. Add lpddr2 512MB size and eMMC options tolocal Kconfig 4. Update license with NXP 2017 5. Add defconfigs for EVB boards Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-292-1 mx6sxscm: add mx6sxscm boards codeJuan Gutierrez2017-04-28-0/+1432
| | | | | | | Move the scm mx6sxscm board generic support code from v2016.03 as the base for converting to use DTB OF_CONTROL Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-291 mx6dqscm: set runtime fdt_file and other fixesJuan Gutierrez2017-04-28-6/+51
| | | | | | | | 1. set fdt_file according to board_rev which is set at runtime 2. Add macros for proper delimitation for different board builds 3. Fix and add proper iomux configuration Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-290-3 mx6dqscm: add dts files for qwks boardsJuan Gutierrez2017-04-28-1/+1057
| | | | | | | Copy the dts files from kernel for qwks boards for preparing enabling the OF_CONTROL. Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-290-2 mx6dqscm: convert to enable OF_CONTROL and DM driversJuan Gutierrez2017-04-28-186/+781
| | | | | | | | | | | | | | | Update mx6dqscm boards code and build configurations to enable OF_CONTROL and DM drivers. 1. Update GPIO codes for adding gpio request 2. Enable USB DM driver 3. Update PMIC and LDO by-pass codes for DM PMIC 4. Add spinor boot support 5. Add lpddr2 modes, sizes and boards on local Kconfig 6. Update license with NXP 2017 7. Add defconfigs for qwks boards Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MXSCM-290-1 mx6dqscm: add mx6dqscm boards codeJuan Gutierrez2017-04-28-0/+3190
| | | | | | | Move the scm mx6dqscm board generic support code from v2016.03 as the base for converting to use DTB OF_CONTROL. Signed-off-by: Juan Gutierrez <juan.gutierrez@nxp.com>
* MLK-14752 common/console.c: remove CONFIG_IS_ENABLED()Fugang Duan2017-04-26-19/+19
| | | | | | | | | | | | | | | Remove CONFIG_IS_ENABLED() macro in the driver, it seems the macro don't work in the config build for mx6sxsabreauto_config platform. And CONFIG_IS_ENABLED(FOO) evaluates to * 1 if CONFIG_SPL_BUILD is undefined and CONFIG_FOO is set to 'y' or 'm', * 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_FOO is set to 'y' or 'm' If enable CONFIG_SPL_BUILD, then CONFIG_FOO doesn't work. Now remove the CONFIG_IS_ENABLED() in the driver. Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
* MLK-14750 mxc_fec: Add compatible string for i.mx6slYe Li2017-04-25-0/+1
| | | | | | | The compatible string "fsl,imx6sl-fec" is missed for i.mx6sl in u-boot FEC driver, so that FEC can't be recognized. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13141 mx6qpsabresd: Do not touch VGEN3 and VGEN5Robin Gong2017-04-21-23/+28
| | | | | | | | | | VGEN3 and VGEN5 have been fused the right value in PF0100 on i.mx6qp board, so software didn't need to change their voltage output anymore. Otherwise, VGEN3 will be wrongly updated from 1.8v to 2.8v. Signed-off-by: Robin Gong <yibin.gong@nxp.com> (cherry picked from commit 6f7f185664a401f03f6ce6c81b996c1f27fdbe73) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14698 imx: lpi2c: fix clock issue when NACK detectedGao Pan2017-04-20-4/+9
| | | | | | | | | | For LPI2C IP, NACK is detected by the rising edge of the ninth clock. In current uboot driver, once NACK is detected, it will reset and then disable LPI2C master. As a result, we can never see the falling edge of the ninth clock. Signed-off-by: Gao Pan <pandy.gao@nxp.com> (cherry picked from commit dd139ee52b709c95af3e0c968bcbc3cf42cca408)
* MLK-14707 fsl_esdhc: Fix eMMC 1.8v setting issueYe Li2017-04-20-4/+4
| | | | | | | | | | | | Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init, then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has already set VSELECT to 1.8v before running the u-boot. This reset in USDHC driver causes a short 2.2v pulse on CMD pin. Fix this issue by not reset VSELECT to 0 when 1.8v flag is set. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit f01ebfdaa57b4c74ede32a6a40cf9cf9184ce049)
* MLK-14708 mmc: fsl_esdhc: fix wrong usage device_get_supply_regulatorPeng Fan2017-04-20-0/+4
| | | | | | | Fix wrong usage of device_get_supply_regulator. device_get_supply_regulator returns 0 on success. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* MLK-14693 mx7ulp: Change PLL rate calculation to avoid div 0Ye Li2017-04-14-2/+8
| | | | | | | | | | | | | The new ROM patch will set DENOM and NUM of APLL and SPLL to 0 to workaround PLL issue. When DENOM is 0, the PLL rate calculation will divide 0 and raise a signal. raise: Signal # 8 caught To avoid such problem, we change our calculation. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit f28cf489e1b3864bac6bae4944d8a73bab30ec32)
* MLK-14689 mx7ulp: Workaround APLL PFD2 to 345.6MhzYe Li2017-04-14-2/+2
| | | | | | | | | | The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28) to workaround the problem. The correct fix should let GPU handle the clock rate in kernel. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit e931d534fd68e0e639082766de17a20e705fd908)
* MLK-14636 Tools: Add python lib dependency check for libfdtYe Li2017-04-06-1/+1
| | | | | | | | | | | | | | The tools/makefile will build a libfdt Python module if swig is available. But actually it not only need swig but also need python libary. We will get build break below when python is not installed. It is better to add more check for python lib. Because applications may install some python libs, but not the full libpython-dev, then the Python.h is missed. We check Python.h to instead checking libs. tools/libfdt_wrap.c:147:21: fatal error: Python.h: No such file or directory Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14365 nand: replace the CONFIG_SYS_USE_NANDYe Li2017-04-06-2/+2
| | | | | | | The CONFIG_SYS_USE_NAND is not used in v2017.03. We have to replace it by other NAND configurations, like CONFIG_CMD_NAND or CONFIG_NAND_MXS. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12527-6 mx6slevkandroid: Add keyboard configurations to whilelistYe Li2017-04-06-0/+6
| | | | | | | To use keyboard on mx6slevk, some configurations are added in android header files. Need adding them to config_whilelist.txt Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12527-5 android: Miss pad setting for buttonYe Li2017-04-06-0/+2
| | | | | | The button pad setting is missed during cherry-pick. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12527-4 android: Fix duplicated configurationYe Li2017-04-06-1/+0
| | | | | | | The CONFIG_USB_GADGET is duplicated set in defconfig and android header file. Remove it from defconfig Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14445-12 mx7ulp_evk: Fix dts building for eMMCYe Li2017-04-06-0/+1
| | | | | | Missed to add eMMC dts file to Makefile Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14628 epdc: Fix configs issueYe Li2017-04-06-15/+14
| | | | | | | | | In Kconfig, the CONFIG_MXC_EPDC depends on CONFIG_LCD. We can't only set the CONFIG_MXC_EPDC in defconfig and set CONFIG_LCD in header file. This will cause the both two configs are not selected. So in fact the epdc codes are not compiled. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-13499 imx6sll: add epdc splash screen supportRobby Cai2017-04-06-9/+294
| | | | | | | | | add splash screen feature for epdc. it's tested on imx6sll arm2 board and evk board. Signed-off-by: Robby Cai <robby.cai@nxp.com> (cherry picked from commit c85c6f2a0f08dfc6c2859fe969b2021ab32b9370) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14627 android: Fix cache unaligned warningYe Li2017-04-06-3/+36
| | | | | | | | The sparse image writing and boot image reading may have cache unaligned problem. The u-boot v2017 will print warning at runtime. This patch fixes the unaligned problem. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14622 mx6sx: update defconfig to enable setexpr commandYe Li2017-04-05-24/+0
| | | | | | | Since we need the setexpr command for m4 image loading, so enable the CONFIG_CMD_SETEXPR for i.MX6SX defconfigs with m4 boot enabled. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14621 fsl_qspi: Set endianness for i.MX platformsYe Li2017-04-05-0/+10
| | | | | | | | The endianness is not set at qspi driver initialization. So if we don't boot from QSPI, we will get wrong endianness when accessing from AHB address directly. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14620 env_sata: Fix build warningYe Li2017-04-05-0/+2
| | | | | | | | | | | | | | | | | Fix below build warning by declaring sata_get_dev the in the part.h common/env_sata.c: In function 'saveenv': common/env_sata.c:70:9: warning: implicit declaration of function 'sata_get_dev' [-Wimplicit-function-declaration] sata = sata_get_dev(env_sata); ^ common/env_sata.c:70:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion] sata = sata_get_dev(env_sata); ^ common/env_sata.c: In function 'env_relocate_spec': common/env_sata.c:116:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion] sata = sata_get_dev(env_sata); Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14608 fsl_esdhc: Fix wp_enable issueYe Li2017-04-05-5/+13
| | | | | | | | | | The wp-gpios property is used for gpio, if this is set, the WP pin is muxed to gpio function, can't be used as internal WP checking. This patch changes to examine the "fsl,wp-controller" for using internal WP checking. And wp-gpios for using gpio pin. Signed-off-by: Ye Li <ye.li@nxp.com>
generated by cgit v1.1 at 2024-08-21 17:31:31 +0000