summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* net: fec_mxc: configure MDIO hold timeMåns Rullgård2016-01-03-3/+15
| | | | | | | | | | | | If the host clock frequency is higher than 100 MHz, the MDIO hold time needs to be increased from its current setting of one cycle in order to meet the specified minium of 10 ns. Writing an appropriate value to the HOLDTIME field of the MII_SPEED register achieves this. Comment copied from Linux kernel. Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Eric Nelson <eric@nelint.com>
* serial_mxc: Fix setup of UARTx_UFCR registerMaximilian Schwerin2016-01-03-1/+8
| | | | | | | | This patch writes the default values for TXTL and RXTL to UARTx_UFCR. Without this patch some older kernel versions crash as UARTx_UFCR was not always correctly initialized. Signed-off-by: Maximilian Schwerin <maximilian.schwerin@tigris.de>
* ARM: imx: fsl_esdhc: fix usage of low 4 bits of sysctl registerEric Nelson2016-01-03-2/+15
| | | | | | | | | | | | | | | | | | | | | | The low four bits of the SYSCTL register are reserved on the USDHC controller on i.MX6 and i.MX7 processors, but are used for clocking operations on earlier models. Guard against their usage by hiding the bit mask macros on those processors. These bits are used to prevent glitches when changing clocks on i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7. >From the i.MX6DQ RM: To prevent possible glitch on the card clock, clear the FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS or DVS in System Control Register) or setting RSTA bit. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Hector Palacios <hector.palacios@digi.com>
* imx: ddr: drop duplicated debug infoPeng Fan2016-01-03-1/+0
| | | | | | | Drop duplicated debug info for tcl. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* arm: novena: Switch novena to config_distro_bootcmdVagrant Cascadian2015-12-14-1/+22
| | | | | | | | | | Switch Novena to distro bootcmd, so it can be used with debian easily. Signed-off-by: Vagrant Cascadian <vagrant@aikidev.net> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Stefano Babic <sbabic@denx.de> Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
* imx: mx6: fix reg base address when runtime usagePeng Fan2015-12-07-4/+4
| | | | | | | | | | | | | | | | | | Should use parenthese to wrap the macro definition, otherwise we will encounter error like the following: " if (base_addr != LCDIF1_BASE_ADDR) { puts("Wrong LCD interface!\n"); return -EINVAL; } " Without this patch, we will always encounter "Wrong LCD interface". Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
* imx: mx6: add missing return valueJeroen Hofstee2015-12-07-0/+2
| | | | | | | cc: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Peng Fan <Peng.Fan@freescale.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
* imx: mx7: enable CONFIG_FSL_CLKPeng Fan2015-12-07-0/+2
| | | | | | | | | | | | | This commit "677f970bc62a661690b3431543d5a5d5e682ba70" introduce a new macro "CONFIG_FSL_CLK" that get_clocks() should not be limited by ESDHC. But that patch missed to enable it for i.MX7. THis patch enables CONFIG_FSL_CLK to let get_clocks work. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Adrian Alonso <aalonso@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sxsabresd: Fix Ethernet PHY reset sequenceFabio Estevam2015-12-07-3/+7
| | | | | | | | | | | | | | | Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. Fix this by calling enable_fec_anatop_clock() earlier and also by adding a 10ms reset delay as recommended in the AR8031 datasheet. Suggested-by: Jörg Krause <joerg.krause@embedded.rocks> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
* cgtqmx6eval: Fix defconfig nameOtavio Salvador2015-12-07-1/+1
| | | | | | After the conversion to SPL the defconfig was renamed, so adjust it. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* arm: imx6: novena: Enable extfs support in SPLMarek Vasut2015-12-01-0/+1
| | | | | | | | Simple patch to enable support for extfs filesystem in SPL, this is useful to those who want to avoid vfat like plague. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* arm: imx6: novena, gw_ventana: Fix use of pfuze100 bit definitionsMarek Vasut2015-12-01-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | The following patch changed the PFUZE100 swbst register bit definitions and broke PMIC configuration on multiple boards, at least on the novena and gw_ventana. This patch fixes it. commit 8fa46350a4c7dca7710362f6c871098557b934ad Author: Peng Fan <Peng.Fan@freescale.com> Date: Fri Aug 7 16:43:45 2015 +0800 power: regulator: add pfuze100 support Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Peng Fan <Peng.Fan@freescale.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Vagrant Cascadian <vagrant@aikidev.net> Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com> Tested-by: Vagrant Cascadian <vagrant@aikidev.net> Reviewed-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Tim Harvey <tharvey@gateworks.com>
* ARM: mxs: fix VDDD brownout settingMichael Heimpold2015-12-01-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At the moment, the desired brownout is at 1.0V. However, this setting cannot be realized by hardware since we have only 3 bits to represent the voltage difference from the target value. Target value is 1500 mV, brownout target is 1000 mV, voltage steps are 25 mV. Register content calculation: (1500 [mV] - 1000 [mV]) / 25 [mV] = 20 (decimal) = 0x14 Register takes only 3 bits, that is 0x4. But 0x4 * 25 [mV] = 100 [mV], that means that actual brownout level is 1500 [mV] - 100 [mV] = 1.4 V. Minimum possible BO level is 1500 [mV] - 0x7 * 25 [mV] = 1315 [mV]. So lets use this value as desired BO value (which is also the same as FSL bootlets use). Signed-off-by: Michael Heimpold <mhei@heimpold.de> Cc: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
* mx6: clock: Modify GPMI clock to support mx6sxYe.Li2015-11-25-0/+12
| | | | | | | On mx6sx, the CCM register bits for GPMI are different as other mx6 platforms. Modify the GPMI clock function to support mx6sx. Signed-off-by: Ye.Li <B37916@freescale.com>
* video: ipu: simplify if else codePeng Fan2015-11-25-3/+1
| | | | | | | | | | Simplify if/else code, since if channel equals to MEM_BG_SYNC or MEM_FG_SYNC, we have value 5 for 'dc_chan'. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
* colibri_vf: Add board_usb_phy_mode functionSanchayan Maity2015-11-25-1/+32
| | | | | | | | Add board_usb_phy_mode function for detecting whether a port is being used as host or client using a GPIO. On Colibri Vybrid we provide GPIO 102 for this very same purpose. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
* cgtqmx6eval: Add DFU supportOtavio Salvador2015-11-25-0/+22
| | | | | | | Add MMC and SPI DFU support. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* iomux-v3: Take MX6D in consideration for imx_iomux_v3_setup_pad()Otavio Salvador2015-11-25-1/+1
| | | | | | | | We should also take MX6D option in consideration when defining imx_iomux_v3_setup_pad(). Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* cgtqmx6eval: Add SPL supportOtavio Salvador2015-11-25-270/+565
| | | | | | | | | Congatec has several MX6 boards based on quad, dual, dual-lite and solo. Add SPL support so that all the variants can be supported Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* cgtqmx6eval: Add fastboot supportOtavio Salvador2015-11-25-0/+6
| | | | | | | | | | | | | | | | | | | Tested basic fastboot commands, such as: On the U-boot prompt: => fastboot 0 On the host PC: $ fastboot getvar bootloader-version -i 0x0525 bootloader-version: U-Boot 2015.10-rc2-09654-g8f41d27 finished. total time: 0.000s $ fastboot reboot -i 0x0525 --> board reboots fine. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* cgtqmx6eval: Use SPI NOR to store the environmentOtavio Salvador2015-11-25-4/+14
| | | | | | | | Congatec boards boot from SPI NOR, so it makes more sense to use SPI NOR to store the environment variables. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* cgtqmx6eval: Add SPI NOR flash supportOtavio Salvador2015-11-25-0/+41
| | | | | | | | | | Add SPI NOR support: => sf probe SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* arm: mx6: Reduce SPL malloc pool sizeMarek Vasut2015-11-23-3/+3
| | | | | | | | | | | | Using 50 MiB malloc pool in SPL is nonsense. Since the caches are not enabled in SPL, it takes 2 seconds to init the pool and has no obvious benefit. Reduce the size to 1 MiB. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Tim Harvey <tharvey@gateworks.com>
* dm: Add timeline and guide for porting serial driversSimon Glass2015-11-20-0/+58
| | | | | | | | | | Add a README with a brief guide to porting serial drivers over to use driver model. Add a timeline also. All serial drivers should be converted by the end of January 2016. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: test: usb: sandbox: Add keyboard tests for sandboxSimon Glass2015-11-19-0/+36
| | | | | | | Add a test that verifies that USB keyboards work correctly on sandbox. This verifies some additional parts of the USB stack. Signed-off-by: Simon Glass <sjg@chromium.org>
* sandbox: Enable USB keyboardSimon Glass2015-11-19-1/+3
| | | | | | | Enable the USB keyboard on sandbox, now that we have a suitable emulation driver. Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: sandbox: Add a USB emulation driverSimon Glass2015-11-19-0/+264
| | | | | | | | | Add a simple USB keyboard driver for sandbox. It provides a function to 'load' it with input data, which it will then stream through to the normal U-Boot input subsystem. When the input data is exhausted, the keyboard stops providing data. Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: sandbox: Add support for interrupt operationsSimon Glass2015-11-19-0/+42
| | | | | | | Allow USB device emulation to support interrupt URBs so that we can use USB keyboards with sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: Avoid open-coded USB constants in usb_kbd.cSimon Glass2015-11-19-5/+5
| | | | | | | Replace the open-coded values with constants to make it clearer what they mean. Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: Drop unused code in usb_kbd.cSimon Glass2015-11-19-30/+0
| | | | | | This was missed in the conversion to driver model. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: test: usb: Add a test for device reorderingSimon Glass2015-11-19-0/+50
| | | | | | | Add tests that 'usb tree' produces the right output when a device changes order on the bus. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: test: usb: Add tests for the 'usb tree' commandSimon Glass2015-11-19-1/+169
| | | | | | | Add tests that this command produces the right output, even when a rescan results in a device disappearing from the bus. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: usb: Remove inactive children after a bus scanSimon Glass2015-11-19-0/+23
| | | | | | | | | | Each scan of the USB bus may return different results. Existing driver-model devices are reused when found, but if a device no longer exists it will stay around, de-activated, but bound. Detect these devices and remove them after the scan completes. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: usb: Deprecate usb_get_dev_index()Simon Glass2015-11-19-0/+9
| | | | | | | | This function should not be used with driver model. While there are users of USB Ethernet that use driver model for USB but not Ethernet, we have to keep it around. Add a comment to that effect. Signed-off-by: Simon Glass <sjg@chromium.org>
* Revert "dm: Export device_remove_children / device_unbind_children"Simon Glass2015-11-19-30/+18
| | | | | | This reverts commit bb52b367f6ca4a3a918e77737f4ff6a1089912d9. Signed-off-by: Simon Glass <sjg@chromium.org>
* Revert "dm: usb: Use device_unbind_children to clean up usb devs on stop"Simon Glass2015-11-19-3/+0
| | | | | | | | This reverts commit 6cda369509e0d3fa5f9e33c9d71589c4523799fa. We want to avoid having the USB stack rely on unbind. Signed-off-by: Simon Glass <sjg@chromium.org>
* Revert "dm: usb: Rename usb_find_child to usb_find_emul_child"Simon Glass2015-11-19-9/+10
| | | | | | | | This reverts commit 9b510df703d282effba4f56ac567aa8011d56e6b. We want to avoid having the USB stack rely on unbind. Signed-off-by: Simon Glass <sjg@chromium.org>
* sandbox: usb: Allow finding a USB emulator for a deviceSimon Glass2015-11-19-2/+25
| | | | | | | | Each USB device has an emulator. Currently this can only be found by supplying the 'pipe' value, which contains the device number. Add a way to find it directly from the emulated device. Signed-off-by: Simon Glass <sjg@chromium.org>
* sandbox: usb: Allow up to 4 emulated devices on a hubSimon Glass2015-11-19-1/+1
| | | | | | To support more advanced testing, support 4 devices instead of 2. Signed-off-by: Simon Glass <sjg@chromium.org>
* sandbox: usb: Allow dynamic emulated USB device descriptorsSimon Glass2015-11-19-20/+28
| | | | | | | | We would like the serial number to come from the device tree node name of the emulated device. This avoids them all having the same name. Adjust the code to support this. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: core: Add safe device iteration macrosSimon Glass2015-11-19-0/+27
| | | | | | Add iteration macros which support unbinding a device within the loop. Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: Refactor USB tree output code for testingSimon Glass2015-11-19-25/+41
| | | | | | | Allow the 'usb tree' command to be used from test code, so that we can verify that it works correctly. Signed-off-by: Simon Glass <sjg@chromium.org>
* test: Record and silence console in testsSimon Glass2015-11-19-0/+22
| | | | | | | | | When running sandbox tests, silence the console to avoid unwanted output. Also, record the console in case tests want to check it. The -v option can be used to enable stdout during tests. Signed-off-by: Simon Glass <sjg@chromium.org>
* sandbox: Enable console recording and silent consoleSimon Glass2015-11-19-0/+4
| | | | | | | Allow console recording so that tests can use it. Also allow the console output to be suppressed, to reduce test output 'noise'. Signed-off-by: Simon Glass <sjg@chromium.org>
* console: Add a console bufferSimon Glass2015-11-19-1/+125
| | | | | | | | | | | | | | | | | | | It is useful to be able to record console output and provide console input via a buffer. This provides sandbox with the ability to run a command and check its output. If the console is set to silent then no visible output is generated. This also provides a means to fix the problem where tests produce unwanted output, such as errors or warnings. This can be confusing. We can instead set the console to silent and record this output. It can be checked later in the test if required. It is possible that this may prove useful for non-test situations. For example the console output may be suppressed for normal operations, but recorded and stored for access by the OS. That feature is not implemented at present. Signed-off-by: Simon Glass <sjg@chromium.org>
* Add a circular memory buffer implementationSimon Glass2015-11-19-0/+637
| | | | | | | | This will be used to support console recording. It provides for a circular buffer which can be written at the head and read from the tail. It supports avoiding data copying by providing raw access to the data. Signed-off-by: Simon Glass <sjg@chromium.org>
* Drop config.h header from display_options.cSimon Glass2015-11-19-1/+0
| | | | | | Since common.h will always include this automatically, it is not needed. Signed-off-by: Simon Glass <sjg@chromium.org>
* Move console definitions into a new console.h fileSimon Glass2015-11-19-18/+131
| | | | | | | | The console includes a global variable and several functions that are only used by a small subset of U-Boot files. Before adding more functions, move the definitions into their own header file. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: usb: Avoid time delays in sandbox testsSimon Glass2015-11-19-1/+14
| | | | | | | Currently the USB tests take around two seconds to run. Remove these unnecessary time delays so that the tests run quickly. Signed-off-by: Simon Glass <sjg@chromium.org>
* sandbox: Add a way to skip time delaysSimon Glass2015-11-19-1/+37
| | | | | | | | Some tests are slow due to delays which are unnecessary on sandbox. The worst offender is USB where we lose two seconds. Add a way to disable time delays. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-08-25 15:59:04 +0000