summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* common: dfu: saperate the dfu common functionalityB, Ravi2016-09-27-59/+92
| | | | | | | | | The cmd_dfu functionality is been used by both SPL and u-boot, saperating the core dfu functionality moving it to common/dfu.c. Signed-off-by: Ravi Babu <ravibabu@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* spl: dfu: add dfu support in SPLB, Ravi2016-09-27-0/+32
| | | | | | | | | | | | | | | | | | | | | | | Traditionally the DFU support is available only as part 2nd stage boot loader(u-boot) and DFU is not supported in SPL. The SPL-DFU feature is useful for boards which does not have MMC/SD, ethernet boot mechanism to boot the board and only has USB inteface. This patch add DFU support in SPL with RAM memory device support to load and execute u-boot. And then leverage full functionality DFU in u-boot to flash boot inital binary images to factory or bare-metal boards to memory devices like SPI, eMMC, MMC/SD card using USB interface. This SPL-DFU support can be enabled through Menuconfig->Boot Images->Enable SPL-DFU support Signed-off-by: Ravi Babu <ravibabu@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* drivers: usb: xhci-fsl: Change burst beat and outstanding pipelined ↵Sriram Dash2016-09-27-0/+13
| | | | | | | | | | | transfers requests This is required for better performance, and performs below tuning: 1. Enable burst length set, and define it as 4/8/16. 2. Set burst request limit to 16 requests. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
* colibri_t30: fix usb ethernet functionalityMarcel Ziswiler2016-09-27-0/+1
| | | | | | | | | | | | | | | | Since commit aa7a648747d8c704a9a81c9e493d386930724e9d ("net: Stop including NFS overhead in defragment max") the following has been reproducibly observed while trying to transfer data over TFTP: Load address: 0x80408000 Loading: EHCI timed out on TD - token=0x8008d80 T EHCI timed out on TD - token=0x88008d80 Rx: failed to receive: -5 This patch fixes this by upping our maximal de-fragmentation aka IP packet size again. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
* net: asix: Fix ASIX 88772B with driver modelAlban Bedel2016-09-27-24/+3
| | | | | | | | | | | | | | | | | | | Commit 147271209a9d ("net: asix: fix operation without eeprom") added a special handling for ASIX 88772B that enable another type of header. This break the driver in DM mode as the extra handling needed in the receive path is missing. However this new header mode is not required and only seems to increase the code complexity, so this patch revert this part of commit 147271209a9d. This also reverts commit 41d1258aceb45b45f9e68f67a9c40f0afbc09dc9 ("net: asix: Fix AX88772B when used with DriverModel") of late. Fixes: 147271209a9d ("net: asix: fix operation without eeprom") Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
* Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini2016-09-26-885/+4733
|\ | | | | | | | | | | | | trini: Drop local memset() from examples/standalone/mem_to_mem_idma2intr.c Signed-off-by: Tom Rini <trini@konsulko.com>
| * armv7: ls102xa: Rename GIC_ADDR and DCSR_RCPM_ADDRYork Sun2016-09-26-4/+4
| | | | | | | | | | | | | | | | | | Instead of using CONFIG_* name space, rename these two macros to SYS_FSL_* space. Signed-off-by: York Sun <york.sun@nxp.com> CC: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig optionYork Sun2016-09-26-2/+5
| | | | | | | | | | | | | | | | Move this option to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * armv8: ls1046ardb_emmc: Fix a typo in defconfigYork Sun2016-09-26-1/+1
| | | | | | | | | | | | | | | | It should be EMMC_BOOT instead of CONFIG_EMMC_BOOT. Signed-off-by: York Sun <york.sun@nxp.com> CC: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * Convert CONFIG_SYS_FSL_ERRATUM_A010315 to Kconfig optionYork Sun2016-09-26-2/+17
| | | | | | | | | | | | | | Move this option to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
| * armv8: ls1012a: Convert CONFIG_LS1012A to Kconfig option ARCH_LS1021AYork Sun2016-09-26-10/+17
| | | | | | | | | | | | | | | | | | Move this config to Kconfig option and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Calvin Johnson <calvin.johnson@nxp.com> CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * driver: ddr: fsl_mmdc: Pass board parameters through data structureYork Sun2016-09-26-73/+87
| | | | | | | | | | | | | | | | | | Instead of using multiple macros, a data structure is used to pass board-specific parameters to MMDC DDR driver. Signed-off-by: York Sun <york.sun@nxp.com> CC: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * armv8: ls1046a: Convert CONFIG_LS1046A to Kconfig option ARCH_LS1046AYork Sun2016-09-26-6/+12
| | | | | | | | | | | | | | | | | | Move this option to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Mingkai Hu <mingkai.hu@nxp.com> CC: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * armv8: ls1046aqds: Add LS1046AQDS board supportShaohui Xie2016-09-14-5/+1866
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls1046ardb: Add LS1046ARDB board supportMingkai Hu2016-09-14-0/+1470
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1046ARDB Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 512 Mbyte NAND flash * Two 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card * On-board 4G eMMC Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: * PCIe1 (SerDes2 Lane0) to miniPCIe slot * PCIe2 (SerDes2 Lane1) to x2 PCIe slot * PCIe3 (SerDes2 Lane2) to x4 PCIe slot SATA: * SerDes2 Lane3 to SATA port USB 3.0: one super speed USB 3.0 type A port one Micro-AB port UART: supports two UARTs up to 115200 bps for console Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls1046a: disable SATA ECC in DCSRShaohui Xie2016-09-14-0/+4
| | | | | | | | | | | | | | | | | | This is a workaround to fix SATA CRC error. Once the root cause is found the ECC disabling will be removed. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls1046a: Enable DDR erratum for ls1046aShengzhou Liu2016-09-14-0/+6
| | | | | | | | | | | | | | | | | | Enable ERRATUM_A008511, ERRATUM_A009801, ERRATUM_A009803, ERRATUM_A009942, ERRATUM_A010165 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-layerscape: spl: remove BSS clearing and board_init_rQianyu Gong2016-09-14-5/+0
| | | | | | | | | | | | | | | | | | | | As per the top level U-Boot README "Board Initialisation Flow" section, board_init_f() should return without calling board_init_r() directly. Clearing BSS and calling board_init_r() will be done in crt0_64.S. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-layerscape: add define CONFIG_STANDALONE_LOAD_ADDR for standalone appShaohui Xie2016-09-14-0/+2
| | | | | | | | | | | | | | | | The CONFIG_STANDALONE_LOAD_ADDR is set to 0x80300000 by default. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-layerscape: Increase L2 Data RAM latency and L2 Tag RAM latencyMingkai Hu2016-09-14-0/+15
| | | | | | | | | | | | | | | | | | | | | | According to design specification, the L2 cache operates at the same frequency as the A72 CPUs in the cluster with a 3-cycle latency, so increase the L2 Data RAM and Tag RAM latency to 3 cycles, or else, will run into different call trace issues. Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * Export memset for standalone AQ FW load appsShaohui Xie2016-09-14-1/+2
| | | | | | | | | | | | | | | | | | | | The 'commit 95279315076c ("board/ls2085rdb: Export functions for standalone AQ FW load apps")' mentioned memset was exported but it was not, this patch exports the memset. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * ddr: fsl: fix a compile issueShaohui Xie2016-09-14-1/+6
| | | | | | | | | | | | | | | | | | | | When CONFIG_SYS_FSL_ERRATUM_A009801 is defined but CONFIG_SYS_FSL_ERRATUM_A008511 not defined, there is compile error that temp32 undeclared, this patch fixes it. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver/ddr/fsl: Add general MMDC driver and reuse common MMDC driver for ls1012aShengzhou Liu2016-09-14-409/+262
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This general MMDC driver adds basic support for Freescale MMDC (Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8 LS1012A SoC for DDR3L, there will be a update to this driver to support more flexible configuration if new features (DDR4, multiple controllers/chip selections, etc) are implimented in future. Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/ LS1012AFRDM. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv7:ls1021a: Enable workaround for DDR erratum A-009942Shengzhou Liu2016-09-14-1/+7
| | | | | | | | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * nxp: ls102xa: add LS1 PSCI system suspendHongbo Zhang2016-09-14-2/+284
| | | | | | | | | | | | | | | | The deep sleep function of LS1 platform, is mapped into PSCI system suspend function, this patch adds implementation of it. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * nxp: ls102xa: add EPU Finite State MachineHongbo Zhang2016-09-14-0/+165
| | | | | | | | | | | | | | | | The EPU Finite State Machie (FSM) is used in both the last stage of system suspend and the earliest stage of system resume. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * nxp: ls102xa: add registers definition for system sleepHongbo Zhang2016-09-14-1/+60
| | | | | | | | | | | | | | | | This patch adds definitions of all the regesters necessary for system sleep. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv7: psci: make v7_flush_dcache_all public for all psci codeHongbo Zhang2016-09-14-3/+5
| | | | | | | | | | | | | | | | | | | | | | The v7_flush_dcache_all function will be called by ls102xa platform system suspend, it is necessary to make it a public call instead of a local one, but changing the LENTRY to ENTRY isn't enough, because there is another one using the same name, so this one gets a psci_ prefix. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls2080a: Remove debug server supportYork Sun2016-09-14-323/+1
| | | | | | | | | | | | Debug server feature has been dropped from roadmap. Signed-off-by: York Sun <york.sun@nxp.com>
| * fsl-layerscape: Add workaround for PCIe erratum A010315Hou Zhiqiang2016-09-14-0/+65
| | | | | | | | | | | | | | | | | | | | As the access to serders protocol unselected PCIe controller will hang. So disable the R/W permission to unselected PCIe controller including its CCSR, IO space and memory space according to the serders protocol field of RCW. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * fsl: csu: add an API to set R/W permission to PCIeHou Zhiqiang2016-09-14-0/+30
| | | | | | | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * fsl: csu: add an API to set individual device access permissionHou Zhiqiang2016-09-14-14/+21
| | | | | | | | | | | | | | | | Add this API to make the individual device is able to be set to the specified permission. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * arm: fsl-layerscape: move forward the non-secure access permission setupHou Zhiqiang2016-09-14-36/+10
| | | | | | | | | | | | | | | | | | | | Move forward the basic non-secure access enable operation, so the subsequent individual device access permission can override it. And collect the dispersed callers in board level, and then move them to SoC level. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * fsl: serdes: ensure accessing the initialized maps of serdes protocolHou Zhiqiang2016-09-14-9/+276
| | | | | | | | | | | | | | | | | | | | | | | | Up to now, the function is_serdes_configed() doesn't check if the map of serdes protocol is initialized before accessing it. The function is_serdes_configed() will get wrong result when it was called before the serdes protocol maps initialized. As the first element of the map isn't used for any device, so use it as the flag to indicate if the map has been initialized. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * ls1043ardb: PPA: add PPA validation in case of secure bootSumit Garg2016-09-14-0/+39
| | | | | | | | | | | | | | | | | | | | As part of Secure Boot Chain of trust, PPA image must be validated before the image is started. The code for the same has been added. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * board: ls1043ardb: move sec_init to board_initSumit Garg2016-09-14-15/+17
| | | | | | | | | | | | | | | | | | | | sec_init() which was earlier called in misc_init_r() is now done in board_init() before PPA init as SEC block will be used during PPA image validation. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver/ddr/fsl: Revise workaround A008511 for A009803York Sun2016-09-14-36/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DDR controller 5.2.1 has this erratum A008511 partially fixed. The workaround needs to be adjusted to take advantage of Vref training. This patch enables the training and force output enable to be off. Erratum A009803 requires the controller to be idel before enabling address parity. It was combined with workaround for A008511. With new A008511 flow, this flow needs to be changed to enabling data init (D_INIT) after the address parity is enabled. Signed-off-by: York Sun <york.sun@nxp.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
| * driver/ddr/fsl: Add more debug registersYork Sun2016-09-14-6/+5
| | | | | | | | | | | | | | 32 more debug registers are added for newer DDR controllers. Signed-off-by: York Sun <york.sun@nxp.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
| * armv8: fsl-layerscape: Update ddr erratum a008336Shengzhou Liu2016-09-14-2/+4
| | | | | | | | | | | | | | | | | | DDR erratum A008336 only applies to DDR controller v5.2.0. DDR controller v5.2.1 already has default 0x43b30002 in EDDRTQCR1 register for optimal performance. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * net: fm: fix spi flash probe for using driver modelQianyu Gong2016-09-14-0/+10
| | | | | | | | | | | | | | | | | | | | | | The current code would always use the speed and mode set by CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE. But if using SPI driver model it should get the values from DT. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | kconfig: introduce kconfig for UBIHeiko Schocher2016-09-26-76/+251
| | | | | | | | | | | | | | | | | | move the UBI config options into Kconfig. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andrew F. Davis <afd@ti.com> Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-coldfireTom Rini2016-09-26-2/+30
|\ \
| * | board: amcore: update to use dm serial driverAngelo Dureghello2016-09-25-1/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | Update amcore board to use dm serial driver. Signed-off-by: Angelo Dureghello <angelo@sysam.it> --- Changes for v2: - None
| * | board: amcore: add update scriptsAngelo Dureghello2016-09-25-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add some useful update scripts. Signed-off-by: Angelo Dureghello <angelo@sysam.it> --- Changes for v.2: - Fix syntax error on upgrade_jffs2 script
* | | i2c: mvtwsi.c: Add support for Marvell Armada 7K/8KStefan Roese2016-09-26-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | By adding the "marvell,mv78230-i2c" compatible property, we can enable this I2C driver to support these new ARM64 chips as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Heiko Schocher <hs@denx.de>
* | | i2c: mv_i2c.c: Validate read length in I2C commandjinghua2016-09-26-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The I2C bus will get stuck when reading 0 byte. So we add validation of the read length in i2c_read(). This issue only occurs on read operation. Signed-off-by: jinghua <jinghua@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Heiko Schocher <hs@denx.de>
* | | i2c: mv_i2c.c: Enable runtime speed selection (standard vs fast mode)Stefan Roese2016-09-26-7/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds runtime speed configuration to the mv_i2c driver. Currently standard (max 100kHz) and fast mode (max 400kHz) are supported. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Heiko Schocher <hs@denx.de>
* | | i2c: mv_i2c.c: Add DM supportStefan Roese2016-09-26-48/+136
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Heiko Schocher <hs@denx.de>
* | | i2c: mv_i2c.c: Prepare driver for DM conversionStefan Roese2016-09-26-126/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To prepare for the DM conversion, we add a layer of compatibility functions to be used by both the legacy and the DM functions. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Heiko Schocher <hs@denx.de>
* | | i2c: mv_i2c.c: Remove CONFIG_HARD_I2CStefan Roese2016-09-26-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_HARD_I2C is not needed, lets remove it. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Heiko Schocher <hs@denx.de>
generated by cgit v1.1 at 2024-08-23 20:44:01 +0000