summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* MLK-10774-5 Add EPDC splash screen for MX 6DL SabreSD and 6SL EVKPeng Fan2015-04-29-1/+1721
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add EPDC splash screen feature for MX6SL EVK, and MX6DL SABRESD board. - Currently, splash screen consists of a simple black border around a white screen. Done this way to save in memory footprint. - EPDC splash screen is disabled by default in the config file for MX6DL_SABRESD and MX6SL_EVK. If left enabled, the U-Boot image will not boot correctly (hang), since some additional content on the boot device (waveform file) is required for EPDC splash to work correctly. Please refer to Linux Reference Manual for how to flash WAVEFORM file. Signed-off-by: Robby Cai <R63905@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit b8ab9b3eabb94bbbc1eea63e7c0e2a87d2d645f4) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/include/asm/arch-mx6/mx6sl_pins.h board/freescale/mx6sabresd/mx6sabresd.c board/freescale/mx6slevk/mx6slevk.c drivers/video/Makefile include/configs/mx6sabresd.h include/configs/mx6slevk.h include/lcd.h drivers/video/Makefile
* MLK-10774-4 fsl:qspi update qspi driverPeng Fan2015-04-29-596/+684
| | | | | | Use freescale vendor qspi driver but not upstream qspi driver Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00328312 i2c: imx: Optimize the i2c device recovery solutionFugang Duan2015-04-29-2/+25
| | | | | | | | | | | | | | | | | From i2c spec, if device pull down the SDA line that causes i2c bus dead, host can send out 9 clock to let device release SDA. But for some special device like pfuze100, it pull down SDA line and the solution cannot take effort. The patch just add NACK and STOP signal after 8 dummy clock, and pmic can release SDA line after the recovery. Test case catch 375 times of i2c hang, and all are recovered. Signed-off-by: Fugang Duan <B38611@freescale.com> (cherry picked from commit 53118db42d201d36ca9067b4bb0e2702399e100b) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00321435-1 imx-common: cpu: Disable mxsfb when necessaryLiu Ying2015-04-29-0/+4
| | | | | | | | | | The kernel may break the display pipeline at boot stage and introduce various display artifacts, so let's disable mxsfb in uboot when necessary. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> (cherry picked from commit 539b8416299ec1ae3f57f866dd3f016bdfaa6875) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-81 gis: Add gis moduleYe.Li2015-04-29-0/+640
| | | | | | | | | | | | Add gis module, current gis is support vadc input. Add power down function to lcdif driver. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit a007b00dd8ef9f773dfdebef0b1deb0990281793) Conflicts: drivers/video/Makefile
* ENGR00315894-80 pxp: Add pxp moduleYe.Li2015-04-29-0/+324
| | | | | | | | | | Add pxp module. Support csc between YUV444 and RGB888 and scaling. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 4c6e1f9ed1b2f5c98a34502b44b6414593fdd290) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-79 csi: Add csi moduleYe.Li2015-04-29-0/+425
| | | | | | | | | Add csi module. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 854ae26758ec8132ef749b98645dd2f43b84e5e2) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-78 vadc: Add vadc moduleYe.Li2015-04-29-0/+602
| | | | | | | | | | Add vadc module. Both PAL and NTSC mode can work. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 03c31ae30c1e81c99f6824221e4801433445e04a) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-70 iMX6SX:Video Update MXS LCDIF driverYe.Li2015-04-29-13/+67
| | | | | | | | | | | | | | Add a new interface "mxs_lcd_panel_setup" to setup fb parameters and specifies the LCDIF controller for multiple controllers of iMX6SX. Pass fb parameters via "videomode" env remains work if the new interface is not called before video initialization. Modify LCDIF clock interface "mxs_set_lcdclk" to support multiple LCDIF controllers on iMX6SX. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 054fed6bab5b05a054c7e3cb5362635a40e6ee18) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-58 RDC: Add an iMX platform driver for RDC-SEMAYe.Li2015-04-29-0/+319
| | | | | | | | | | | | | | | | | | | | The RDC driver provides interfaces for setting peripherals and masters at BSP initialization, before using the peripherals driver. Another interfaces for lock/unlock RDC semaphore and permission check. The driver assumes boot CPU which runs u-boot is in Domain 0 (default setting on boot). Users should not set it to other domains. The peripherals ID and masters ID may change on different chip, each should provide definitions of the IDs and be included in "imx-rdc.h". Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 964b2672bfbec14629f5767e59e73fd3bb185e3a) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/imx-common/Makefile arch/arm/include/asm/arch-mx6/imx-regs.h
* ENGR00315894-55 iMX6SX: add debug monitor supportYe.Li2015-04-29-0/+25
| | | | | | | | | | | | | | | | Debug monitor will print out last failed AXI access info when system reboot is caused by AXI access failure, only works when debug monitor is enabled. Enable this module on i.MX6SX. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit df6ac8531d498021ed379c74fc1847bd2cec7179) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/include/asm/arch-mx6/imx-regs.h
* ENGR00331269 arm: mx6: select OSC as uart's clk parentAnson Huang2015-04-29-0/+9
| | | | | | | | | | As M4 is sourcing UART clk from OSC, to make UART work when M4 is enabled, need to select OSC as clk parent, 24M OSC is enough for debug UART in uboot. Signed-off-by: Anson Huang <b20788@freescale.com> (cherry picked from commit 8b903f529370fdc59cc03b3ced954ed894753044) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00322860 iMX6SX: Add function to check M4 status before bootingYe.Li2015-04-29-1/+31
| | | | | | | | | Add new function "arch_auxiliary_core_check_up" to check whether M4 is already up. Therefore, avoid starting M4 again when it is running. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 54a0803b29c5ab459bedfb2c68c1e94b89866aa1) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-56 CMD: Add new command "bootaux" to boot auxiliary coreYe.Li2015-04-29-0/+43
| | | | | | | | | | | | | To boot a auxiliary core in asymmetric multicore system, introduce the new command "bootaux" to do it. Example of boot auxliary core from 0x70000000 where stores the boot head information that should be parsed by each core. "bootaux 0x70000000" Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit fd00c322d058e02953a336517547174edaf2c573) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00321299 gis: clean csi0 input mux set bit in GPRSandor Yu2015-04-29-0/+6
| | | | | | | | | | When gis enable in uboot, the CSI0 input mux select setting to vadc module, clean the bit when gis disabled. Signed-off-by: Sandor Yu <R01008@freescale.com> (cherry picked from commit ae66b17b7da3be50dc81ca636b67e8e879f52e26) (cherry picked from commit c83fd326e810c2fff44b8b02e78406d5d04c977c) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00321260-1 iMX6: Add support to get CPU serial numberYe.Li2015-04-29-0/+13
| | | | | | | | | | The android boot needs get_board_serial function to get the CPU uid as the serial number. Implement this function to read the uid from fuse for all iMX6 platforms. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 8d355a9d6f138e1c1cd04dbadb7b5b3e2d692701) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00320350 iMX6SLEVK: Fix build warning of PCIE Phy power downYe.Li2015-04-29-0/+2
| | | | | | | | | | | | | | Since the iMX6SL does not have PCIE module, should not define the function "imx_set_pcie_phy_power_down" for it. Otherwise, get the build warning below: arch/arm/cpu/armv7/mx6/soc.c:446:13: warning: 'imx_set_pcie_phy_power_down' defined but not used [-Wunused-function] static void imx_set_pcie_phy_power_down(void) Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 987c48c07c9ef62fa3fe55faa6f7369b30637127) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00319965 pcie: mask the imx6sl outRichard Zhu2015-04-29-2/+7
| | | | | | | | | imx6sl doesn't have the pcie module, mask the pcie related codes from imx6sl. Signed-off-by: Richard Zhu <r65037@freescale.com> (cherry picked from commit acaff11da33f8f0cb1521d3c48e64e7ed9a87bec) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00319415 pcie: random link down issue after warm-rstRichard Zhu2015-04-29-0/+18
| | | | | | | | | | | | | | | | | | | There are about 0.02% percentage on some imx6q/dl/solo hw boards, random pcie link down when warm-reset is used. Make sure to clear the ref_ssp_en bit16 of gpr1 before warm-rst, and set ref_ssp_en after the pcie clks are stable to workaround it. rootcause: * gpr regisers wouldn't be reset by warm-rst, while the ref_ssp_en is required to be reset by pcie. (work-around in u-boot) * ref_ssp_en should be set after pcie clks are stable. (work-around in kernel) Signed-off-by: Richard Zhu <r65037@freescale.com> (cherry picked from commit 5cc825b12c6b86a22f1a6a0535b52cf3ee142e77) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-77 mx6 soc: Add vadc power up/down functionYe.Li2015-04-29-0/+59
| | | | | | | | | | | | Add vadc power up/down function. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 96d990ef754a879f6ca9da4adf6e0be3d21cdc51) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/include/asm/arch-mx6/imx-regs.h
* ENGR00315894-76 mx6 clock: Add vadc clock enable functionYe.Li2015-04-29-0/+11
| | | | | | | | | | | | | Add vadc clock enable function. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 721c7a1448c5b7265b597b83d18f8338a27ea213) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/cpu/armv7/mx6/clock.c arch/arm/include/asm/arch-mx6/clock.h
* ENGR00315894-71 iMX6SX Update registers and clock for displayYe.Li2015-04-29-0/+445
| | | | | | | | | | | | | Add registers and clock functions to enable/set LCDIF clock and LVDS. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit ef9d769f9ad1b504a1df8b987d269df9944d8e0c) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/include/asm/arch-mx6/clock.h arch/arm/include/asm/arch-mx6/crm_regs.h arch/arm/include/asm/arch-mx6/imx-regs.h
* ENGR00315894-57 iMX6SX: Add M4 boot support at soc levelYe.Li2015-04-29-0/+29
| | | | | | | | | | | Implement the override function "arch_auxiliary_core_up" to boot Cortex-M4 by executing command "bootaux". The parameter "boot_private_data" points to fields where stores the stack address and PC address for M4 to run. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 98c15deb3083d5dac7900c58e95f2ac2f422a4d3) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-3 iMX6SX/SL: Modify SOC to support two ENETPeng Fan2015-04-29-6/+48
| | | | | | | | | | | | | | | | | | | iMX6SX has different enet system clocks with iMX6SL, and has two ENET controllers. So update clocks and soc APIs accordingly to support this features. 1. Enet RGMII TX clock source may come from external or internal PLL. By default, use the external phy CLK_25M output as TX clock source. When using internal PLL as source, the function enable_fec_anatop_clock must be called to enable clock for each enet controller. 2. Modify the MAC address function "imx_get_mac_from_fuse" to get either ENET MAC address. 3. Add configuration "CONFIG_FEC_MXC_25M_REF_CLK" to enable ENET 25Mhz reference clock. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ENGR00315894-11 i.mx6:shutdown vddpu and pcie phy to save powerYe.Li2015-04-29-0/+31
| | | | | | | | | | | | | shutdown vddpu and pcie phy to save power Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 580011f86caf137d59a487694f6f7da042164e05) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/cpu/armv7/mx6/soc.c
* MLK-10774-2 HDMI: splash screen function enhancementPeng Fan2015-04-29-31/+76
| | | | | | | | | | | | | | -Change HDMI video mode to VGA. -Add pixel clock fraction part setting in IPU driver, fix video mode timing issue. -Add overflow state clear workaround, fix kernel hang in HDMI driver issue. -Correct IPU clock to 264MHz. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit 45d532a0237f5baf2ec95b4364ec5bc94d312689) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-1 imx: LDO: add LDO bypassPeng Fan2015-04-29-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | This patch is from two commits: 1. 748eac71fde78aa0c2e8cb3a3bab94bd994c06f5 ENGR00315499-5: Support i.MX6 1.2GHz via LDO bypass Add check for 1.2GHz core speed. If Speed grading fuse is for 1.2GHz, enable LDO bypass and setup PMIC voltages. LDO bypass is dependent on the flatten device tree file. 2. 93d457e4c601ee5266bc30b7dfa5fa1bbfa8500a MLK-9891-1: ARM: imx6: split WDOG_B setting from set_anatop_bypass() function We set WDOG_B in set_anatop_bypass() before, because it is the only case, but now on i.mx6sabreauto board, we didn't use ldo-bypass mode, but have to use WDOG_B to reboot whole board, so split these code to independent function so that board file can call it freely. Board code is not included, board ldo bypass code will be in bsp update code. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* Prepare v2015.04Tom Rini2015-04-13-1/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* break build if it would produce broken binaryPavel Machek2015-04-13-0/+4
| | | | | | | Add an error in known-bad case so that we don't produce broken and hard to debug binaries. Signed-off-by: Pavel Machek <pavel@denx.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-04-13-3/+693
|\
| * ARM: mx5: add support for USB armory boardAndrej Rosano2015-04-09-0/+670
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Inverse Path USB armory board, an open source flash-drive sized computer based on Freescale i.MX53 SoC. http://inversepath.com/usbarmory Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Chris Kuethe <chris.kuethe@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-By: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
| * ARM: mx5: move to a standard arch/board approachAndrej Rosano2015-04-09-0/+22
| | | | | | | | | | | | | | | | | | | | Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the commit: 89ebc82137bebb11a8191f8b9cbf08f2533ae8bc Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
| * Fix mxc_hab documenation for DEK blob generationUlises Cardenas2015-04-08-0/+1
| | | | | | | | | | | | | | | | | | | | Include/fsl_sec.h defines sec_in and sec_out, according to the platform's endianess. Therefore, CONFIG_SYS_FSL_LE needs to be declared in the configuration file of the target, in order to use enable the DEK blob generation command. This requirement is not explicit in the README.mxc_hab. Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
| * mx53loco: Disable printing cpuinfoFabio Estevam2015-04-08-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 32df39c741788e ("mx5: fix get_reset_cause") we have the following boot messages on a mx53qsb: U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: POR Board: MX53 LOCO I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial CPU: Freescale i.MX53 rev2.1 at 1000 MHz Reset cause: unknown reset Net: FEC [PRIME] The CPU and Reset cause lines appear twice. Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via I2C to raise the CPU voltage so that it can run at 1GHz. To avoid such misleading double printings, disable printing cpu info for now. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
* | ARM: rpi: add a couple more revision IDsStephen Warren2015-04-13-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | According to Gordon Henderson's WiringPi library, there are some more Pi revision IDs out there. Add support for them. http://git.drogon.net/?p=wiringPi;a=blob_plain;f=wiringPi/wiringPi.c;hb=5edd177112c99416f68ba3e8c6c4db6ed942e796 At least ID 0x13 is out in the wild: Reported-by: Chee-Yang Chau <cychau@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
* | ARM: fix arch/arm/Makefile for TegraMasahiro Yamada2015-04-11-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 79d75d752717 (ARM: move -march=* and -mtune= options to arch/arm/Makefile), all the Tegra boards are broken because the SPL is built for ARMv7. Insert Tegra-specific code to arch/arm/Makefile to set compiler flags for an earlier ARM architecture. Note: The v1 patch for commit 79d75d752717 *was* correct when it was submitted. Notice it was originally written for multi .config configuration where Kconfig set CONFIG_CPU_V7/CONFIG_CPU_ARM720T for Tegra U-Boot Main/SPL, respectively. But, until it was merged into the mainline, commit e02ee2548afe (kconfig: switch to single .config configuration) had been already applied there. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Stephen Warren <swarren@nvidia.com> Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
* | arm: armada-xp: Fix SPL for AXP by using save_boot_params_retStefan Roese2015-04-11-1/+1
| | | | | | | | | | | | | | | | | | | | | | Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced a different method to return from save_boot_params(). The SPL support for AXP has been pulled and changing to this new method is now required for SPL to work correctly. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
* | Merge git://git.denx.de/u-boot-arcTom Rini2015-04-10-1/+46
|\ \
| * | arc: fix separate compilation of start.oAlexey Brodkin2015-04-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While testing "arc: make sure _start is in the beginning of .text section" I haven't done proper clean-up of built binaries and so missed another tiny bit that lead to the following error: --->8--- LD u-boot arc-linux-ld.bfd: cannot find arch/arc/lib/start.o Makefile:1107: recipe for target 'u-boot' failed make: *** [u-boot] Error 1 --->8--- Fix is trivial: put "start.o" in "extra-y". Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
| * | arc: make sure _start is in the beginning of .text sectionAlexey Brodkin2015-04-10-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is important to have entry point in the beginning of .text section because it allows simple loading and execution of U-Boot. For example pre-bootloader loads U-Boot in memory starting from offset 0x81000000 and then just jumps to the same address. Otherwise pre-bootloader would need to find-out where entry-point is. In its turn if it deals with binary image of U-Boot there's no way for pre-bootloader to get required value. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
| * | board: axs10x - support v3 mother-boardAlexey Brodkin2015-04-09-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There're 2 versions of motherboards that could be used in ARC SDP. The only important difference for U-Boot is different NAND IC in use: [1] v2 board (we used to support up until now) sports MT29F4G08ABADAWP while [2] v3 board sports MT29F4G16ABADAWP They are almost the same except data bus width 8-bit in [1] and 16-bit in [2]. And for proper support of 16-bit data bus we have to pass NAND_BUSWIDTH_16 option to NAND driver core - which we do now knowing board type we're running on. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* | | integrator: consolidate flash infoLinus Walleij2015-04-10-33/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | This consolidates the flash settings for the Integrator and activates the new ARM flash image support for them so images can be loaded by name from flash. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | vexpress64: juno: add default NOR flash bootLinus Walleij2015-04-10-1/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This modifies the vexpress64 Juno configuration so that it will by default load and boot a kernel and a device tree from the images stored in the NOR flash. When we are at it, also define the proper command line for the Juno and indicate that the USB stick (/dev/sda1) is the default root file system. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | common/armflash: Support for ARM flash imagesLinus Walleij2015-04-10-0/+285
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ARM reference designs all use a special flash image format that stores a footer (two versions exist) at the end of the last erase block of the image in flash memory. Version one of the footer is indicated by the magic number 0xA0FFFF9F at 12 bytes before the end of the flash block and version two is indicated by the magic number 0x464F4F54 0x464C5348 (ASCII for "FLSHFOOT") in the very last 8 bytes of the erase block. This command driver implements support for both versions of the AFS images (the name comes from the Linux driver in drivers/mtd/afs.c) and makes it possible to list images and load an image by name into the memory with these commands: afs - lists flash contents afs load <image> - loads image to address indicated in the image afs load <image> <addres> - loads image to a specified address This image scheme is used on the ARM Integrator family, ARM Versatile family, ARM RealView family (not yet supported in U-Boot) and ARM Versatile Express family up to and including the new Juno board for 64 bit development. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | Merge branch 'master' of git://git.denx.de/u-boot-fdtTom Rini2015-04-10-2/+0
|\ \ \
| * | | fdt: nios: Fix warning in ft_cpu_setup()Simon Glass2015-04-10-2/+0
| |/ / | | | | | | | | | | | | | | | | | | This function should not return a value. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Thomas Chou <thomas@wytron.com.tw>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2015-04-10-77/+3653
|\ \ \
| * | | lpc32xx: add support for board work_92105Albert ARIBAUD \(3ADEV\)2015-04-10-1/+1129
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Work_92105 from Work Microwave is an LPC3250- based board with the following features: - 64MB or 128MB SDR DRAM - 1 GB SLC NAND, managed through MLC controller. - Ethernet - Ethernet + PHY SMSC8710 - I2C: - EEPROM (24M01-compatible) - RTC (DS1374-compatible) - Temperature sensor (DS620) - DACs (2 x MAX518) - SPI (through SSP interface) - Port expander MAX6957 - LCD display (HD44780-compatible), controlled through the port expander and DACs This board has SPL support, and uses the LPC32XX boot image format. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
| * | | Introduce CONFIG_SPL_PANIC_ON_RAW_IMAGEAlbert ARIBAUD \(3ADEV\)2015-04-10-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE. An SPL which define this will panic() if the image it has loaded does not have a mkimage signature. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
| * | | lpc32xx: add lpc32xx-spl.bin boot image targetAlbert ARIBAUD \(3ADEV\)2015-04-10-0/+181
| | | | | | | | | | | | | | | | Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
generated by cgit v1.1 at 2024-09-19 09:44:05 +0000