summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* doc: cleanup - move board READMEs into respective board directoriesWolfgang Denk2012-07-29-626/+565
| | | | | | | | | | | | | | | | Also drop a few files referring to no longer / not yet supported boards. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Jason Jin <jason.jin@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
* net: sh_eth: add support for SH7757's GETHERYoshihiro Shimoda2012-07-23-0/+9
| | | | | | | | | SH7757 has 2 ETHERs and 2 GETHERs. This patch supports the SH7757's GETHER. If CONFIG_SH_ETHER_USE_GETHER is defined using SH7757, the driver handles the GETHER. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* net: sh_eth: modify the definitions of regsiterYoshihiro Shimoda2012-07-23-181/+258
| | | | | | | | | The previous code had many similar definitions in each CPU. This patch borrows from the sh_eth driver of Linux kernel. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* net: sh_eth: add SH_ETH_TYPE_ conditionYoshihiro Shimoda2012-07-23-33/+32
| | | | | | | | | | | | | | | | | | | | | At the moment, the driver supports the following CPUs: - GETHER (Gigabit Ethernet) : SH7763, SH7734 - ETHER (Fast Ethernet) : SH7724, SH7757 And the driver had the following "#if": #if defined(CONFIG_CPU_SH7763) || defined(CONFIG_CPU_SH7734) #if !defined(CONFIG_CPU_SH7757) && !defined(CONFIG_CPU_SH7724) - Those are for GETHER #if defined(CONFIG_CPU_SH7724) || defined(CONFIG_CPU_SH7757) - This is for ETHER So, for clean up the code, this patch adds SH_ETH_TYPE_GETHER and SH_ETH_TYPE_ETHER. And then, the patch modifies the above "#if". Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* net: sh_eth: clean up for the SH7757's codeYoshihiro Shimoda2012-07-23-20/+3
| | | | | | | | The SH7757's ETHER can work using the SH7724's setting. So, the patch modifies it. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* net: fec_mxc: Fix MDC for xMIIbenoit.thebaudeau@advans2012-07-19-1/+1
| | | | | | | | | The MDC signal is available on all xMII (i.e. 'not 7-wire') interfaces, so mii_speed has to be set for all these interfaces, and not only for MII. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* net: fec_mxc: Fix setting of RCR for xMIIbenoit.thebaudeau@advans2012-07-19-5/+3
| | | | | | | | | | | | | | | | | | At least on i.MX25, the RMII mode did not work, which is fixed by this patch. The MII_MODE bit of the FEC RCR register means xMII, i.e. 'not 7-wire', so set it accordingly. According to the xMII and 7-wire (aka GPSI) standards, full duplex should be available on xMII, but not on 7-wire, so set FCE accordingly. The FEC may support full duplex for 7-wire too, but the reference manual does not say that, so avoid an invalid assumption. Actually, the choice between half and full duplex also depends on the endpoint/switch/repeater configuration, so a config option could be added for that, but there has been no need for it so far. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* net: nfs: make NFS_TIMEOUT configurableTetsuyuki Kobayashi2012-07-12-1/+12
| | | | | | | NFS_TIMEOUT is constant value defined in net/nfs.c. But sometimes it needs to adjust. This patch enables to override NFS_TIMEOUT by defining CONFIG_NFS_TIMEOUT in a board specific config file. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
* Merge branch 'next' of git://git.denx.de/u-boot-net into nextWolfgang Denk2012-07-12-26/+96
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | * 'next' of git://git.denx.de/u-boot-net: net: Inline the new eth_setenv_enetaddr_by_index function net: allow setting env enetaddr from net device setting net/designware: Consecutive writes to the same register to be avoided CACHE: net: asix: Fix asix driver to work with data cache on net: phy: micrel: make ksz9021 phy accessible net: abort network initialization if the PHY driver fails phylib: phy_startup() should return an error code on failure net: tftp: fix type of block arg to store_block Signed-off-by: Wolfgang Denk <wd@denx.de>
| * net: Inline the new eth_setenv_enetaddr_by_index functionJoe Hershberger2012-07-11-1/+1
| | | | | | | | | | | | This function is currently only used in one case. Inline for now. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * net: allow setting env enetaddr from net device settingRob Herring2012-07-11-1/+19
| | | | | | | | | | | | | | | | | | | | If the net driver has setup a valid ethernet address and an ethernet address is not set in the environment already, then set the environment variables from the net driver setting. This enables pxe booting on boards which don't set ethaddr env variable. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * net/designware: Consecutive writes to the same register to be avoidedDinh Nguyen2012-07-11-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit is an add-on to f6c4191f. There are a few registers where consecutive writes to the same location should be avoided or have a delay. According to Synopsys, here is a list of the registers and bit(s) where consecutive writes should be avoided or a delay is required: DMA Registers: Register 0 Bit 7 Register 6 All bits except for 24, 16-13, 2-1. GMAC Registers: Registers 0-3 All bits Registers 6-7 All bits Register 10 All bits Register 11 All bits except for 5-6. Registers 16-47 All bits Register 48 All bits except for 18-16, 14. Register 448 Bit 4. Register 459 Bits 0-3. Signed-off-by: Dinh Nguyen <dinguyen@altera.com> Reviewed-by: Matthew Gerlach <mgerlach@altera.com> Acked-by: Amit Virdi <amit.virdi@st.com>
| * CACHE: net: asix: Fix asix driver to work with data cache onMarek Vasut2012-07-11-13/+17
| | | | | | | | | | | | | | | | | | The asix driver did not align buffers, therefore it didn't work with data cache enabled. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
| * net: phy: micrel: make ksz9021 phy accessibleTroy Kisky2012-07-11-2/+14
| | | | | | | | | | | | | | | | | | | | Micrel accidentally used the same part number for the KS8721 and KSZ9021. So, both cannot be in the same build of u-boot. Add a config option to handle this. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com>
| * net: abort network initialization if the PHY driver failsTimur Tabi2012-07-11-6/+39
| | | | | | | | | | | | | | | | | | | | Now that phy_startup() can return an actual error code, check for that error code and abort network initialization if the PHY fails. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Nobuhiro Iwamamatsu <nobuhiro.iwamatsu.yj@renesas.com> (sh_eth part) Acked-by: Stephan Linz <linz@li-pro.net> (Xilinx part, xilinx_axi_emac and xilinx_ll_temac) Reviewed-by: Marek Vasut <marex@denx.de> (FEC part)
| * phylib: phy_startup() should return an error code on failureTimur Tabi2012-07-11-1/+4
| | | | | | | | | | | | | | phy_startup() calls the PHY driver's startup function, but it ignores the return code from that function, and so it never returns any failures. Signed-off-by: Timur Tabi <timur@freescale.com>
| * net: tftp: fix type of block arg to store_blockJayachandran Chandrasekharan Nair2012-07-11-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | The block argument for store_block can be -1 when the tftp sequence number rolls over (i.e TftpBlock == 0), so the first argument to store_block has to be of type 'int' instead of 'unsigned'. In our environment (gcc 4.4.5 mips toolchain), this causes incorrect 'offset' to be generated for storing the block, and the tftp block with number 0 will be written elsewhere, resulting in a bad block in the downloaded file and a memory corruption. Signed-off-by: Jayachandran Chandrasekharan Nair <jayachandranc@netlogicmicro.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk2012-07-12-36/+51
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-i2c: mx28evk: Add I2C support mxs-i2c: Fix internal address byte order mxc_i2c: remove setting speed at each start mx6qsabrelite: add i2c support mxc_i2c: specify i2c base address in config file Signed-off-by: Wolfgang Denk <wd@denx.de>
| * | mx28evk: Add I2C supportFabio Estevam2012-07-11-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add I2C support. Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
| * | mxs-i2c: Fix internal address byte orderTorsten Fleischer2012-07-11-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Large EEPROMs, e.g. 24lc32, need 2 byte to address the internal memory. These devices require that the high byte of the internal address has to be written first. The mxs_i2c driver currently writes the address' low byte first. The following patch fixes the byte order of the internal address that should be written to the I2C device. Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de> CC: Marek Vasut <marex@denx.de> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * | mxc_i2c: remove setting speed at each startTroy Kisky2012-07-11-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Other then being very weird, this code was also wrong. For example, say I set speed to 100K. I'll read back the speed as 85937. But the speed is really 85937.5, so we I reset the speed to 85937, I'll get 73660.7. After a couple of transactions my speed is now exactly 68750 so it will remain there. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * | mx6qsabrelite: add i2c supportTroy Kisky2012-07-11-0/+19
| | | | | | | | | | | | | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | mxc_i2c: specify i2c base address in config fileTroy Kisky2012-07-11-29/+20
| |/ | | | | | | | | | | | | | | | | The following platforms had their config files changed flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd and mx53loco. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | net: fix typo in arp clean upMike Frysinger2012-07-10-1/+1
| | | | | | | | | | | | | | | | | | | | The clean up patch missed an &, so we end up passing an int rather than a pointer to the sprintf function. arp.c: In function 'ArpReceive': arp.c:197: warning: format '%p' expects type 'void *', but argument 3 has type 'int' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | net/sh-ether: Fix build by removing ECSIPR_BRCRXIP and otherNobuhiro Iwamatsu2012-07-10-4/+3
|/ | | | | | | | When support sh7734 of sh-ether, ECSIPR_BRCRXIP and other were removed. Therefore SH7757 and SH7724 can not build. This revise this probelem. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
* Prepare v2012.07-rc1Wolfgang Denk2012-07-10-3/+3
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Minor Coding Style cleanupWolfgang Denk2012-07-10-9/+3
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2012-07-10-216/+628
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: tegra: define fdt_load/fdt_high variables tegra: enable bootz command tegra: usb: Fix device enumeration problem of USB1 tegra: trimslice: set up serial flash pinmux tegra: add pin_mux_spi() board initialization function tegra: add GMC/GMD funcmux entry for SFLASH tegra: bootcmd: start USB only when needed tegra: bootcmd enhancements tegra: add enterrcm command tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG Add env vars describing U-Boot target board tegra: usb: fix wrong error check tegra: add ULPI on USB2 funcmux entry tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches tegra: Add Tamonten Evaluation Carrier support tegra: Use SD write-protect GPIO on Tamonten tegra: Implement gpio_early_init() on Tamonten tegra: Allow boards to perform early GPIO setup tegra: plutux: Add device tree support tegra: medcom: Add device tree support tegra: Rework Tamonten support beagle: add eeprom expansion board info for bct brettl4 Signed-off-by: Wolfgang Denk <wd@denx.de>
| * tegra: define fdt_load/fdt_high variablesStephen Warren2012-07-09-0/+2
| | | | | | | | | | | | | | | | | | | | These variables act like loadaddr, but for a device tree image. Defining them in the environment allows boot scripts to be identical on Tegra20 and Tegra30, which have different memory base addresses, and hence need different values for these variables. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: enable bootz commandStephen Warren2012-07-09-0/+1
| | | | | | | | | | | | | | | | bootz is just like bootm, except that it can boot a raw zImage, without requiring it to be wrapped inside a uImage. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: usb: Fix device enumeration problem of USB1Jim Lin2012-07-09-1/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | A known hardware issue of USB1 port where bit 1 (connect status change) of PORTSC register will be set after issuing Port Reset (like "usb reset" in u-boot command line). This will be treated as an error and stops later device enumeration. Therefore we clear that bit after Port Reset in order to proceed later device enumeration. Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: trimslice: set up serial flash pinmuxStephen Warren2012-07-09-0/+5
| | | | | | | | | | | | | | | | | | | | | | When Trimslice is booted from serial flash, the boot ROM does this, so U-Boot doesn't need to. However, booting from the SD slot for recovery purposes, the boot ROM does not set up the pinmux for serial flash. Add code to U-Boot to set this up, so that an SD-based recovery U-Boot image can upgrade the U-Boot in serial flash. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add pin_mux_spi() board initialization functionStephen Warren2012-07-09-0/+7
| | | | | | | | | | | | | | | | Boards can override this to set up the pinmux correctly to access serial flash. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add GMC/GMD funcmux entry for SFLASHStephen Warren2012-07-09-0/+13
| | | | | | | | | | | | | | This is used on TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: bootcmd: start USB only when neededStephen Warren2012-07-09-3/+11
| | | | | | | | | | | | | | | | | | | | Instead of initializing USB as soon as bootcmd is executed, defer it until the first boot device that (potentially in the case of network) uses USB is scanned. This avoids initializing USB when booting from MMC, so speeds that up. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: bootcmd enhancementsStephen Warren2012-07-09-30/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Place the list of searched boot devices, file-system types, boot file locations/prefixes, and boot script names into variables. This allows the user to override them directly (e.g. to change boot order, or select the specific values they use) without having to edit the main bootcmd and script_boot variables. The default boot order is changed from USB, MMC, DHCP to MMC, USB, DHCP. This speeds up the typical MMC boot case. People who want USB boot can now edit variable boot_targets appropriately. Also, reformat BOOTCMDS_COMMON to fit within 80 columns. Potential future enhancements might be: * Allow boards to specify which of bootcmd_mmc0/... should be defined, based on the HW they contain. * Allow boards to influence the order that the boot targets are added into the boot_targets variable. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add enterrcm commandStephen Warren2012-07-09-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tegra's boot ROM supports a mode whereby code may be downloaded and flash programmed over a USB connection. On dev boards, this is typically entered by holding down a "force recovery" button and resetting the CPU. However, not all boards have such a button (one example is the Compulab Trimslice), so a method to enter RCM from software is useful. This change implements the command "enterrcm" to do this, and enables it for all Tegra boards by default. Even on boards other than Trimslice, controlling this over a UART may be useful, e.g. to allow simple remote control without the need for mechanical button actuators, or hooking up relays/... to the button. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIGStephen Warren2012-07-09-0/+1
| | | | | | | | | | | | | | | | | | So that all Tegra boards define environment variables that describe themselves. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * Add env vars describing U-Boot target boardStephen Warren2012-07-09-0/+44
| | | | | | | | | | | | | | | | | | | | | | This can be useful for generic scripts. For example, rather than hard- coding a script to ext2load tegra-harmony.dtb, it could load ${soc}-${board}.dtb and hence not need adjustments to run on multiple boards. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: usb: fix wrong error checkLucas Stach2012-07-09-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | loop_count runs down from 10000, so the correct condition to error out is ==0. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren.nvidia@gmail.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add ULPI on USB2 funcmux entryLucas Stach2012-07-09-1/+15
| | | | | | | | | | | | | | | | | | | | | | This is needed as a prerequisite for Tegra USB ULPI support within U-Boot. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switchesTom Warren2012-07-09-6/+6
| | | | | | | | | | | | | | | | | | Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
| * tegra: Add Tamonten Evaluation Carrier supportThierry Reding2012-07-09-0/+192
| | | | | | | | | | | | | | | | | | | | | | The Tamonten Evaluation Carrier is an evaluation board for the Tamonten processor board. More information is available here: http://www.avionic-design.de/en/products/nvidia-tegra-tamonten-system-en/nvidia-tegra-tamonten-evboard-en.html Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: Use SD write-protect GPIO on TamontenThierry Reding2012-07-09-1/+3
| | | | | | | | | | | | | | | | | | GPIO PI6 can be used to obtain the write-protect status of an SD card inserted into the SD slot. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: Implement gpio_early_init() on TamontenThierry Reding2012-07-09-0/+8
| | | | | | | | | | | | | | | | | | | | | | The PI4 GPIO is used on Tamonten to reset carrier board peripherals. Power sequencing hardware on the carrier pulls the reset low before powering up the Tegra, and the CPU is supposed to signal readiness, and therefore bring peripherals out of reset by pulling PI4 high. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: Allow boards to perform early GPIO setupThierry Reding2012-07-09-0/+8
| | | | | | | | | | | | | | | | | | The new gpio_early_init() function, which does nothing by default, can be overridden by boards to configure GPIOs at an early stage. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: plutux: Add device tree supportThierry Reding2012-07-09-1/+78
| | | | | | | | | | | | | | | | | | Device tree support is required for working USB host support, which in turn enables ethernet support. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: medcom: Add device tree supportThierry Reding2012-07-09-1/+78
| | | | | | | | | | | | | | | | | | Device tree support is required for working USB host support, which in turn enables ethernet support. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: Rework Tamonten supportThierry Reding2012-07-09-170/+13
| | | | | | | | | | | | | | | | | | | | | | This commit uses the common Tegra board implementation instead of duplicating a lot of the code. In addition, the Plutux and Medcom specific board files can be removed as the MMC/SD setup is common among all Tamonten-based boards. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * beagle: add eeprom expansion board info for bct brettl4Peter Meerwald2012-07-09-2/+6
| | | | | | | | | | | | | | | | | | this is for a prototyping board vendor/product ids have been added to http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
generated by cgit v1.1 at 2024-11-09 06:09:31 +0000