summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* usb: phy: omap_usb_phy: implement usb_phy_power() for AM437xFelipe Balbi2014-07-09-1/+21
| | | | | | | | Newer AM437x silicon requires us to explicitly power up the USB2 PHY. By implementing usb_phy_power() we can achieve that. Signed-off-by: Felipe Balbi <balbi@ti.com>
* usb: host: xhci: make sure to power up PHYFelipe Balbi2014-07-09-0/+1
| | | | | | | some boards won't work if the PHY isn't explicitly powered up. Signed-off-by: Felipe Balbi <balbi@ti.com>
* doc: Add zynq fragment to git-mailrc fileMichal Simek2014-07-09-0/+1
| | | | | | | | | | This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: OMAP4/5: Change omap4_sdp/panda and omap5_uevm maintainerLokesh Vutla2014-07-09-3/+3
| | | | | | | Updating omap4_sdp/panda and omap5_uevm maintainer. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: R Sricharan <r.sricharan@ti.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-07-09-30/+215
|\
| * mx6: soc: Update the comments of set_ldo_voltage()Fabio Estevam2014-07-09-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces set_ldo_voltage() function that can be used to set the voltages of any of the three LDO regulators controlled by the PMU_REG_CORE register. Prior to this commit there was a single set_vddsoc() which only configured the VDDSOC regulator. Update the comments to align with the new set_ldo_voltage() implementation. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * MX6: Correct calculation of PLL_SYSAndre Renaud2014-07-09-1/+1
| | | | | | | | | | | | | | DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do the shift after the multiply to avoid rounding errors Signed-off-by: Andre Renaud <andre@bluewatersys.com>
| * ARM: m53evk: Update default environmentLothar Rubusch2014-07-09-1/+86
| | | | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Lothar Rubusch <lothar@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
| * ARM: m53evk: Adjust mtdparts settingsMarek Vasut2014-07-09-9/+8
| | | | | | | | | | | | | | | | | | Adjust the mtdparts settings to allow for alternative boot images and for using UBI. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * ARM: m53evk: add needed commands and optionsMarek Vasut2014-07-09-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | - "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * ARM: m28evk: Update default environmentLothar Rubusch2014-07-09-3/+84
| | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Lothar Rubusch <lothar@denx.de>
| * ARM: m28evk: Adjust mtdpartsMarek Vasut2014-07-09-9/+8
| | | | | | | | | | | | Adjust the mtdparts to also consider factory-programmed config block. Signed-off-by: Marek Vasut <marex@denx.de>
| * ARM: m28evk: add needed commands and optionsMarek Vasut2014-07-09-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | - "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* | Merge branch 'tom' of git://git.denx.de/u-boot-x86Tom Rini2014-07-07-3/+8
|\ \
| * | buildman: fix toolchain priority_listMasahiro Yamada2014-07-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | '-elf' appears twice in the toolchain priority_list. The second one is rudundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
| * | buildman: fix to display warning message for missing [toolchain] sectionMasahiro Yamada2014-07-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Toolchains.__init__ is expected to display a warning message when the [toolchain] section is missing from ~/.buildman file. But it never works. In that case, instead, buildmain fails with an error message which is difficult to understand: Traceback (most recent call last): File "tools/buildman/buildman", line 126, in <module> control.DoBuildman(options, args) File "/home/foo/u-boot/tools/buildman/control.py", line 78, in DoBuildman toolchains = toolchain.Toolchains() File "/home/foo/u-boot/tools/buildman/toolchain.py", line 106, in __init__ config_fname) NameError: global name 'config_fname' is not defined Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
| * | cosmetic: doc: update README.generic-boardMasahiro Yamada2014-07-07-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | Now MIPS supports 'generic board' feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
| * | patman: Only apply patches when we know the original HEADSimon Glass2014-07-07-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When patman applies the patches it checks out a new branch, uses 'git am' to apply the patches one by one, and then tries to go back to the old branch. If you try this when the branch is 'undefined', this doesn't work as patman cannot restore the correct branch after applying the patches. It seems that 'undefined' is created by git and is persistent after it is created, so that you can end up on quite an old branch. Add a check for the 'undefined' branch to avoid this. Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Simon Glass <sjg@chromium.org>
* | | TI:omap3: enable CONFIG_CMD_DHCP for omap3_beagleTyler Baker2014-07-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following patch re-enables the dhcp functionality on omap3_beagle. It was removed with df4dbb5df6ab1c1d27b3fd4acbaad69b47095daf when omap3_beagle was converted to use ti_omap3_common.h. I have tested beagleboard and beagleboard-xm with this patch and confirmed dhcp is working. Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
* | | kmake: include DTB section into u-boot.bin if CONFIG_OF_EMBED enabledAlexey Ignatov2014-07-07-0/+4
| | | | | | | | | | | | | | | Fixes a bug when objcopy doesn't put .dtb.init.rodata section to resulting u-boot.bin, so u-boot was unable to find embedded DTB.
* | | git-mailrc: Add sunxi custodians.Ian Campbell2014-07-07-0/+3
| | | | | | | | | | | | | | | Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com>
* | | fit: make sha256 support optionalDirk Eibach2014-07-07-0/+14
| | | | | | | | | | | | | | | | | | | | | sha256 has some beefy memory footprint. Make it optional for constrained systems. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Remove commands to reduce footprintDirk Eibach2014-07-07-4/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit "2842c1c fit: add sha256 support" badly increased memory footprint, so some of our boards did not build anymore. Since monitor base must not be changed I removed some commands to save memory. Maybe making sha256 optional for fit would be an option for the future since it really has some beefy footprint. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: iocon: Modify iocon hardware startupDirk Eibach2014-07-07-5/+4
| | | | | | | | | | | | | | | | | | | | | To avoid peer "ChReceivePathStatus"-messages on iocon startup, initialize PHYs as soon as possible. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Enable scrambling on DP501Dirk Eibach2014-07-07-0/+1
| | | | | | | | | | | | | | | | | | | | | For proper displayport performance, scrambling has to be enabled, but is turned off on DP501 by default. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Make gdsys osd hardware detection more robustDirk Eibach2014-07-07-60/+79
| | | | | | | | | | | | Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Configure bridge on DP501 to support DDC onlyDirk Eibach2014-07-07-3/+5
| | | | | | | | | | | | | | | | | | | | | The I2C bridge on DP501 supports EDID, MCCS and HDCP by default. Allow EDID only to avoid I2C address conflicts. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Increase iocon and dlv10g version stringDirk Eibach2014-07-07-2/+2
| | | | | | | | | | | | Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Fix dlvision-10g I2C configurationDirk Eibach2014-07-07-2/+8
| | | | | | | | | | | | | | | | | | | | | PPC4xx config options were not complete. ICS8N3QV01 and SIL1178 needed some more configuration. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | i2c: IHS I2C master driverDirk Eibach2014-07-07-18/+261
| | | | | | | | | | | | | | | | | | | | | | | | IHS I2C master support was merely a hack in the osd driver. Now it is a proper u-boot I2C framework driver, supporting the v2.00 master features. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: iocon: Support DisplayPort hardwareDirk Eibach2014-07-07-85/+83
| | | | | | | | | | | | | | | | | | There is a new iocon hardware flavor, supporting DisplayPort finally. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: controlcenterd: Use new API for setting i2c busDirk Eibach2014-07-07-4/+9
| | | | | | | | | | | | Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: gdsys: Adapt sdhc_boot.c to mmc_get_env_addr API changeDirk Eibach2014-07-07-1/+1
| | | | | | | | | | | | Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | board: controlcenterd: Fix pci accessDirk Eibach2014-07-07-3/+3
| | | | | | | | | | | | | | | | | | | | | readl was called with values instead of pointers to these values. Why this ever did work is a mystery... Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* | | blackfin, powerpc: remove redundant definitions of ARRAY_SIZEMasahiro Yamada2014-07-07-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | Since ARRAY_SIZE macro is defined in include/common.h, re-defining it in arch-specific files is redundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Sonic Zhang <sonic.zhang@analog.com>
* | | blackfin: Add more dcache functionsVasili Galka2014-07-07-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add invalidate_dcache_range() and flush_dcache_range() for the blackfin architecture. Such functions already exist on this arch with different names, so just forward the call. This fixes the build of bf609-ezkit board as it uses drivers/net/designware.c which requires the above functions. Cc: Sonic Zhang <sonic.adi@gmail.com>, Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vasili Galka <vvv444@gmail.com>
* | | blackfin: Fix warning about undefined functionVasili Galka2014-07-07-0/+1
| | | | | | | | | | | | | | | | | | | | | get_sclk() was not defined in bfin_wdt.c, include the corresponding header. Cc: Sonic Zhang <sonic.adi@gmail.com> Signed-off-by: Vasili Galka <vvv444@gmail.com>
* | | m68k: Fix incorrect memory access on M5235Vasili Galka2014-07-07-16/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The csarX and cscrX registers in the fbcs_t struct are 16-bit for CONFIG_M5235 and 32-bit wide otherwise. The code in cpu_init.c accessed them always as 32-bit, effectively creating a wrong memory access on M5235. Fixed that by choosing out_be16/out_be32 depending on whether CONFIG_M5235 is defined or not. Cc: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Vasili Galka <vvv444@gmail.com>
* | | m68k: Fix bug, "address of" operator was forgottenVasili Galka2014-07-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | in_be16() shall be passed a pointer to register and not its value. This is clearly a typo resulting in a wrong memory access, so fix it. Cc: Alison Wang <b18965@freescale.com>, Jason Jin <Jason.jin@freescale.com> Signed-off-by: Vasili Galka <vvv444@gmail.com>
* | | mpc8xx: remove spc1920 board supportMasahiro Yamada2014-07-07-1367/+1
| | | | | | | | | | | | | | | | | | This board is old enough and has no maintainer. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | mpc8xx: remove v37 board supportMasahiro Yamada2014-07-07-1241/+2
| | | | | | | | | | | | | | | | | | This board is old enough and has no maintainer. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | mpc8xx: remove fads board supportMasahiro Yamada2014-07-07-2442/+6
| | | | | | | | | | | | | | | | | | These boards are old enough and have no maintainers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | mpc8xx: remove netta, netta2, netphone board supportMasahiro Yamada2014-07-07-10221/+3
| | | | | | | | | | | | | | | | | | These boards are old enough and have no maintainers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | mpc8xx: remove rbc823 board supportMasahiro Yamada2014-07-07-1552/+3
| | | | | | | | | | | | | | | | | | This board is old enough and has no maintainer. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | mpc8xx: remove RPXlite_dw, quantum board supportMasahiro Yamada2014-07-07-2765/+3
| | | | | | | | | | | | | | | | | | These boards are old enough and have no maintainers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | mpc8xx: remove qs850, qs860t board supportMasahiro Yamada2014-07-07-3876/+3
| | | | | | | | | | | | | | | | | | These boards are old enough and have no maintainers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | tpm: don't use unneeded double bracketsJeroen Hofstee2014-07-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | clang is tempted to inteprete such a condition as a assignment as well. Since it isn't don't use double brackets. cc: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | | vcma9/lowlevel_init.S: trivial: terminate commentJeroen Hofstee2014-07-07-1/+1
| | | | | | | | | | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* | | README: document CONFIG_ENV_IS_IN_SPI_FLASHWu, Josh2014-07-07-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The option can be used to save the environment in spi flash. Implementation code is already exist in command/env_sf.c. But the documentation is missing. This patch add the details for this option to the README file. Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* | | env_fat: use get_device_and_partition() during env save and loadWu, Josh2014-07-07-60/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use get_device_and_partition() is better since: 1. It will call the device initialize function internally. So we can remove the mmc intialization code to save many lines. 2. It is used by fatls/fatload/fatwrite. So saveenv & load env should use it too. 3. It can parse the "D:P", "D", "D:", "D:auto" string to get correct device and partition information by run-time. Also we remove the FAT_ENV_DEVICE and FAT_ENV_PART. We use a string: FAT_ENV_DEVICE_AND_PART. For at91sam9m10g45ek, it is "0". That means use device 0 and if: a)device 0 has no partition table, use the whole device as a FAT file system. b)device 0 has partittion table, use the partition #1. Refer to the commit: 10a37fd7a4 for details of device & partition string. Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
generated by cgit v1.1 at 2024-11-06 12:45:12 +0000