summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* mpc85xx: Add deep sleep support on T1040QDSTang Yuantian2014-04-22-0/+16
| | | | | | | Add deep sleep support on T1040QDS platform. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx/t104x: Add deep sleep framework supportTang Yuantian2014-04-22-4/+80
| | | | | | | | | | When T104x soc wakes up from deep sleep, control is passed to the primary core that starts executing uboot. After re-initialized some IP blocks, like DDRC, kernel will take responsibility to continue to restore environment it leaves before. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: Add support for the supplement configuration unit registerTang Yuantian2014-04-22-0/+22
| | | | | | | | | | | | The supplement configuration unit (SCFG) provides chip-specific configuration and status registers for the device. It is the chip defined module for extending the device configuration unit (DCFG) module. It provides a set of CCSR registers in addition to those available in the device configuration unit. The base address for this unit is 0x0F_C000. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* drivers/ddr: Fix possible out of bounds errorYork Sun2014-04-22-58/+64
| | | | | | | | | This is a theoretical possible out of bounds error in DDR driver. Adding check before using array index. Also change some runtime conditions to pre-compiling conditions. Signed-off-by: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/net/fm/memac_phy: Initialize mdio_clock for SoCs wih FMANv3Priyanka Jain2014-04-22-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | MDIO clock needs to be initialized in u-boot code for SoCs having FMAN-v3(v3H or v3L) controller due to below reasons -On SoCs that have FMAN-v3H like B4860, default value of MDIO_CLK_DIV bits in mdio_stat(mdio_cfg) register generates mdio clock too high (much higher than 2.5MHz), violating the IEEE specs. -On SOCs that have FMAN-v3L like T1040, default value of MDIO_CLK_DIV bits is zero, so MDIO clock is disabled. So, for proper functioninig of MDIO, MDIO_CLK_DIV bits needs to be properly initialized. Also this type of initialization is generally done in PBI(pre-bootloader) phase using rcw.But for chips like T1040 which support deep-sleep, such type of initialization cannot be done in PBI phase due to the limitation that during deep-sleep resume, FMAN (MDIO) registers are not accessible in PBI phase. So, mdio clock initailization must be done as part of u-boot. This initialization code is implemented in memac_phy.c which gets compiled only for SoCs having FMANv3, so no extra compilation flag is required. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fsl/usb: Increase TXFIFOTHRESH value for usb write in T4 Rev 2.0Nikhil Badola2014-04-22-0/+27
| | | | | | | | | | | Increase TXFIFOTHRES field value in TXFILLTUNING register of usb for T4 Rev 2.0. This decreases data burst rate with which data packets are posted from the TX latency FIFO to compensate for latencies in DDR pipeline during DMA. This avoids Tx buffer underruns and leads to successful usb writes Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t104xrdb: Add support of CPLDPrabhakar Kushwaha2014-04-22-0/+174
| | | | | | | | | | | T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features. This support of CPLD includes - files and register defintion - Commands to swtich alternate bank and default bank Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/cpu/mpc85xx: Add MAC address for layer 2 switchCodrin Ciubotariu2014-04-22-0/+29
| | | | | | | | | | | T1040RDB and T1040QDS boards have an integrated l2 switch. The switch needs a MAC address for Layer 2 protocols (MSTP, LLDP, LACP, etc). Setting a MAC address on l2switchaddr will add a MAC in device-tree, under node l2switch. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Cc: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/T1040: add mtdparts suppport for T104xRDB and T1040QDSPrabhakar Kushwaha2014-04-22-0/+34
| | | | | | | | We use dynamical mtdparts partition instead of directly puting mtd partitions nodes in device tree. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/T208xRDB: add mtdparts suppportShengzhou Liu2014-04-22-0/+16
| | | | | | | | We use dynamical mtdparts partition instead of directly puting mtd partitions nodes in device tree. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/T208xQDS: add mtdparts suppportShengzhou Liu2014-04-22-0/+17
| | | | | | | | We use dynamical mtdparts partition instead of directly puting mtd partitions nodes in device tree. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t104xrdb: Unification of T104xRDB header filesvijay rai2014-04-22-722/+36
| | | | | | | | | | | | | | T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB. T104xRDB header file can support both T1040RDB and T1042RDB_PI header. Patch makes following changes -Update Boards.cfg file for T1040RDB and T1042RDB_PI -Add new T104xRDB header file -Delete T1040RDB, T1042RDB_PI header file Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/mmc: fix compile warningsPrabhakar Kushwaha2014-04-22-1/+5
| | | | | | | | | | | | | | Fix following compile warnings fsl_esdhc_spl.c: In function 'mmc_boot': fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable] fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable] fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable] fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable] fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Add workaround for erratum A007212York Sun2014-04-22-0/+99
| | | | | | | | | | | | | | | | | Erratum A007212 for DDR is about a runaway condition for DDR PLL oscilliator. Please refer to erratum document for detail. For this workaround to work, DDR PLL needs to be disabled in RCW. However, u-boot needs to know the expected PLL ratio. We put the ratio in a reserved field RCW[18:23]. U-boot will skip this workaround if DDR PLL ratio is set, or the reserved field is not set. Workaround for erratum A007212 applies to selected versions of B4/T4 SoCs. It is safe to apply the workaround to all versions. It is helpful for upgrading SoC without changing u-boot. In case DDR PLL is disabled by RCW (part of the erratum workaround), we need this u-boot workround to bring up DDR clock. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/t208xqds: fix nor chip selection when nand bootShengzhou Liu2014-04-22-10/+18
| | | | | | | | NOR flash is on CS1 instead of CS2 when NAND boot. So correct NOR chip selection to CS1 from CS2. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fsl/usb: Workaround for USB erratum-A007075Nikhil Badola2014-04-22-0/+33
| | | | | | | | | | | | Put a delay of 5 millisecond after reset so that ULPI phy gets enough time to come out of reset. Erratum A007075 applies to following SOCs and their variants, if any P1010 rev 1.0 B4860 rev 1.0, 2.0 P4080 rev 2.0, 3.0 Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx/T1040QDS_D4: Add DDR4 supportYork Sun2014-04-22-28/+31
| | | | | | | T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Add DDR4 support to Freescale DDR driverYork Sun2014-04-22-321/+2378
| | | | | | | Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register calculation and programming. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/85xx: Fix e6500 L2 cache stash IDsScott Wood2014-04-22-4/+8
| | | | | | | | The value written to L2CSR1 didn't match the value written to the device tree. Signed-off-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* net/phy: Fix PHY id for VSC8514Codrin Ciubotariu2014-04-22-1/+1
| | | | | | | | | | In the current Datasheet for VSC8514 there is a mistake, saying that the PHY id is 0x70570. The real value in the identifier registers is 0x70670. Linux PHY driver uses 0x70670 also. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Cc: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/fsl_ifc: Add a function to finalize CS0 address bindingYork Sun2014-04-22-0/+8
| | | | | | | | | For fsl-lsch3 NOR flash boot, IFC CS0 needs to be binded with address within 32-bit at fist. After u-boot relocates to DDR, CS0 can be binded to higher address to support large space. Signed-off-by: York Sun <yorksun@freescale.com> CC: Prabhakar Kushwaha <prabhakar@freescale.com>
* board/b4860qds:Slow MDC clock to comply IEEE specs in PBI configPrabhakar Kushwaha2014-04-22-0/+3
| | | | | | | | | | The MDC generate by default value of MDIO_CLK_DIV is too high i.e. higher than 2.5 MHZ. It violates the IEEE specs. So Slow MDC clock to comply IEEE specs Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* t1040rdb/qe: add QE support for T1040RDBZhao Qiang2014-04-22-0/+4
| | | | | | | | add CONFIG_QE, CONFIG_U_QE and CONFIG_SYS_QE_FW_ADDR into "include/configs/T1040RDB.h" Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* QE/U-QE: Add U-QE supportZhao Qiang2014-04-22-5/+32
| | | | | | | | | | | | | Modify code to adapt to both u-qe and qe. U_QE is a kind of cutted QE. the differences between U_QE and QE 1. UCC: U_QE supports 2 UCCs while QE supports up to 8 UCCs. 2. IMMR: have different immr base addr. 3. iopin: U_QE doesn't need to config iopin. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and ↵Zhao Qiang2014-04-22-61/+66
| | | | | | | | | | | CONFIG_SYS_QE_FW_ADDR CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address. Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address, and CONFIG_SYS_QE_FW_ADDR for QE microcode address. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T1040QDS and T1040RDBAneesh Bansal2014-04-22-1/+5
| | | | | | | | | | | | | Secure Boot Target is added for T1040QDS and T1040RDB Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T1040QDS and CONFIG_T1040RDB Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T2080QDSAneesh Bansal2014-04-22-1/+4
| | | | | | | | | | | Secure Boot Target is added for T2080QDS Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080QDS. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T4240QDS and T4160QDSAneesh Bansal2014-04-22-1/+3
| | | | | | | | | | | Secure Boot Target is added for T4240QDS and T4160QDS Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T4240QDS. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for B4860QDSAneesh Bansal2014-04-22-6/+35
| | | | | | | | | | | | | | | | | Changes: 1. L2 cache is being invalidated by Boot ROM code for e6500 core. So removing the invalidation from start.S 2. Clear the LAW and corresponding configuration for CPC. Boot ROM code uses it as hosekeeping area. 3. For Secure boot, CPC is configured as SRAM and used as house keeping area. This configuration is to be disabled once in uboot. Earlier this disabling of CPC as SRAM was happening in cpu_init_r. As a result cache invalidation function was getting skipped in case CPC is configured as SRAM.This was causing random crashes. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add NAND secure boot target for BSC9132QDSAneesh Bansal2014-04-22-1/+10
| | | | | | | | | | In case of secure boot from NAND, the DDR is initialized by the BootROM using the config words (CF_WORDS) in the CF_HEADER and u-boot image is copied from NAND to DDR by the BootROM. So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for BSC9132QDSAneesh Bansal2014-04-22-7/+12
| | | | | | | | | | Add NOR, SPI and SD secure boot targets for BSC9132QDS. Changes: - Debug TLB entry is not required for Secure Boot Target. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc8xxx: SECURE BOOT- Disable law 0 for non PBL platformsAneesh Bansal2014-04-22-0/+10
| | | | | | | | | ISBC creates a LAW 0 entry for non PBL platforms, which is not disabled before transferring the control to uboot. The LAW 0 entry has to be disabled. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/p1010rdb: SECURE BOOT- enable workaround for IFC errata A003399Aneesh Bansal2014-04-22-2/+1
| | | | | | | | | The workaround for IFC errata A003399 was not enabled in case of secure boot. So, secure boot from NOR was not working. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/p1010rdb: SECURE BOOT enabled for NANDAneesh Bansal2014-04-22-1/+2
| | | | | | | | | | In case of secure boot from NAND, the DDR is initialized by the BootROM using the config words (CF_WORDS) in the CF_HEADER and u-boot image is copied from NAND to DDR by the BootROM. So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fsl/usb: Fix phy type for Second USB controllerNikhil Badola2014-04-22-2/+6
| | | | | | | | | Set correct phy_type value for second USB controller. This is required for supporting SOCs having 2 USB controllers working simultaneously, one with UTMI phy and other with ULPI phy Signed-off-by: Nikhil Badola <B46172@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* PPC 85xx: Add qemu-ppce500 machineAlexander Graf2014-04-22-4/+592
| | | | | | | | | | | | | | | | For KVM we have a special PV machine type called "ppce500". This machine is inspired by the MPC8544DS board, but implements a lot less features than that one. It also provides more PCI slots and is supposed to be enumerated by device tree only. This patch adds support for the generic ppce500 machine and tries to rely solely on device tree for device enumeration. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* PPC 85xx: Add ELF entry pointAlexander Graf2014-04-22-0/+1
| | | | | | | | | | | | We want to be able to directly execute the ELF binary without going through the u-boot.bin one. To know where we have to start executing this ELF binary we have to tell the linker where our entry point is. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* PPC: 85xx: Generalize DDR TLB mapping functionAlexander Graf2014-04-22-15/+40
| | | | | | | | | | The DDR mapping function really is just a generic virtual -> physical mapping function. Generalize it so it can support any virtual starting offset and IO maps just the same. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* PPC: 85xx: Remove IVOR resetAlexander Graf2014-04-22-101/+5
| | | | | | | | | | | There is no need to set IVORs to anything but their default values, so let's leave them where they are. Suggested-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> [York Sun: Add back $(obj)start.S section in mpc8572ds/Makefile] Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_support: Add helper function to read "ranges" propertyAlexander Graf2014-04-22-0/+96
| | | | | | | | | | | | | This patch adds a helper function that can be used to interpret most "ranges" properties in the device tree. It reads the n'th range out of a "ranges" array and returns the node's virtual address of the range, the physical address that range starts at and the size of the range. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_support: split fdt_getprop_u32_defaultAlexander Graf2014-04-22-6/+34
| | | | | | | | | | We already have a nice helper to give us a property cell value with default fall back from a path. Split that into two helpers - one for the old path based lookup and one to give us a value based on a node offset. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ARM:tegra20: Remove aes debug printsTom Rini2014-04-18-9/+0
| | | | | | | | In 6e7b9f4 some of the debug prints for AES code moved into the generic code, so we remove these additional calls. Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Tom Warren <twarren@nvidia.com>
* aes: make apply_cbc_chain_data non-staticStephen Warren2014-04-18-14/+16
| | | | | | | | | | | | | | | | | | Tegra's crypto.c uses apply_cbc_chain_data() to sign the warm restart code. This function was recently moved into the core aes.c and made static, which prevents the Tegra code from compiling. Make it public again to avoid the compile errors: arch/arm/cpu/tegra20-common/crypto.c: In function ‘sign_object’: arch/arm/cpu/tegra20-common/crypto.c:74:3: warning: implicit declaration of function ‘apply_cbc_chain_data’ [-Wimplicit-function-declaration] arch/arm/cpu/built-in.o: In function `sign_object': .../arch/arm/cpu/tegra20-common/crypto.c:74: undefined reference to `apply_cbc_chain_data' .../arch/arm/cpu/tegra20-common/crypto.c:78: undefined reference to `apply_cbc_chain_data' Fixes: 6e7b9f4fa0ae ("aes: Move the AES-128-CBC encryption function to common code") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de>
* build: Use filechk rules to create and update u-boot.ldsJon Loeliger2014-04-18-4/+5
| | | | | | | | | | | | | Prior to this patch, the top-level linker script u-boot.lds used a simple $(call if_changed) check when generated. That mechanism misses cases where a possible include file change induces a change in the u-boot.lds too. This patch converts it to a stronger check using ($call filechk) that will also notice differences in file contents and will catch changes due to pre-processing as well. Signed-off-by: Jon Loeliger <jon.loeliger@oracle.com>
* buildman: make output dir configurableDaniel Schwierzeck2014-04-18-1/+4
| | | | | | | | Add an option to specify the output directory to override the default path '../'. This is useful for building in a ramdisk. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* e1000: remove redundant assignmentDavid Müller (ELSOFT AG)2014-04-18-1/+0
| | | | | Signed-off-by: David Mueller <d.mueller@elsoft.ch> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* bootm: set max decompression size for LZOKees Cook2014-04-18-1/+1
| | | | | | | | | | The LZO decompressor wasn't initializing the maximum output size, which meant it would fail to decompress most of the time. Reported-by: Matthias Weißer <weisserm@arcor.de> Signed-off-by: Kees Cook <keescook@chromium.org> Tested-by: Matthias Weißer <weisserm@arcor.de> Acked-by: Simon Glass <sjg@chromium.org>
* kbuild: add user-supplied CPPFLAGS, AFLAGS and CFLAGSMasahiro Yamada2014-04-18-0/+5
| | | | | | | | Like Linux Kernel, this commit provides environment variables KCPPFLAGS, KAFLAGS and KCFLAGS, which are useful to pass additional options. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kbuild: docbook: sync with Linux Kernel v3.15-rc1Masahiro Yamada2014-04-18-19/+10
| | | | | | | | | | | | | | | | | | | | This commit imports DocBook-related updates from v3.14 to v3.15-rc1. - commit ec3fadd64b9940baa2a369bf978e8561837db3f5 kbuild: docbook: use $(obj) and $(src) rather than specific path - commit 100da4c0150c97ce34d4d3b38bf2f5449b05ae4f kbuild: docbook: specify KERNELDOC dependency correctly - commit 6f89b9c1d6b29eaa600ac4a8ac1314b0d06f15e3 kbuild: docbook: include cmd files more simply - commit ac6d662a95a6989d83b259ccf8ec01dd7903af73 doc: Add "*.svg" to DocBook/.gitignore - commit 832919bfcf0cfd75767c68b0c61f7cf48be860a8 DocBook: Make mandocs parallel-safe - commit c4d79a4799719f2b0cd354ee498aad605730c97e work around xmlto bug in htmldocs Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kbuild: sync with Linux Kernel v3.15-rc1Masahiro Yamada2014-04-18-13/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit imports Kbuild-related updates from v3.14 to v3.15-rc1. - commit 3d3d6b8474204b6819688c9800774d52d370a538 kbuild: LLVMLinux: Adapt warnings for compilation with clang - commit 61163efae02040f66a95c8ed17f4407951ba58fa kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang - commit 79192ca8ebd9a25c583aa46024a250fef1e7766f scripts: objdiff: detect object code changes between two commits - commit 1c9e70a55b088d97a59241744fe459409d0c3582 kbuild: create a build directory automatically for out-of-tree build - commit a03fcb50e816a69acffb13b5e56db75063aeba8a kbuild: remove redundant '.*.cmd' pattern from make distclean - commit 13338935f1574a2dcd1c891461b0dcc42f8cff42 kbuild: move "quote" to Kbuild.include to be consistent - commit bfdfaeae500a3b194b73b01e92a8034791a58b7f kbuild: specify build_docproc as a phony target - commit f4d4ffc03efc864645b990e1d579bbe1b8e358a4 kbuild: dtbs_install: new make target - commit 1e64ff42ea3d8d2fc8aa71f9717b3c1cb6c2f893 Kbuild, lto: Disable LTO for asm-offsets.c - commit ccbef1674a1579842c7dbdf554efca85d2cd245a Kbuild, lto: add ld-version and ld-ifversion macros - commit ae63b2d7bdd9bd66b88843be0daf8e37d8f0b574 scripts/tags.sh: Ignore *.mod.c - commit e36aaea28972c57a32a3ba5365e61633739719b9 kbuild: Fix silent builds with make-4 Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
generated by cgit v1.1 at 2024-11-06 08:59:24 +0000